Related
Hi ,
I had 1.72.00wwe on my phone but i was tryin 2 upgrade it further but it got stuck while upgrading and its showing seril while not on cradle and while on cradle its showing usb 1.06
plz hlp me iam newbee and not good in programmin .I also have asecond Xda2 with 1.66.00wwe plz tell if it can b of any help
Reset your device, place it in the cradle and re-run the upgrade.
thanx i tried it already from 2 computers in one its showing error 103 no rom image found and in another its showing error 101 country code problem
Which ROM are you attempting to upgrade to? Which one exactly had you previously upgrade to? What operator do you use?
I'm asking all this to try and get a better picture. Normally, people in your situation can recover by applying the same upgrade again, or, at worst, re-applying the one they are upgrading from.
Make sure you are in bootloader mode (by pressing Jog button and Power button at the same time as pressing reset) before retrying any upgrade. Also make sure the USB cradle is plugged directly into a USB port on your PC and not through a hub and that the power supply is connected to the cradle. It may help to make sure that Activesync isn't running also.
active sync
in the active sync tray it shows that not connected
Well i had 1.72.00wwe rom image 1.14 earlier and iwas tryiong to upgrade to 1.72. something can't remember exactly but it was with rom image 1.17 it was downloaded from t mobile and my current phone is from o2
Click to expand...
Click to collapse
Activesync is not needed for upgrades. The upgrade process looks after its own connection. I suggest you follow the procedures in my post here to overcome the Country ID error problem. You will need to know what the device's operator and language IDs are currently set to, which is why I asked you above. I suspect you won't have Devicedata.txt, so it becomes necessary to know what operator and language the previous upgrade was.
to revive your XDA2 again
The main point is what is ROM 1.66 come from (e.g. i-mate ot T-mobile)
If you doesn't upgrade 1.66 ROM by yourself or it came from factory ,you must tell us which operator did you buy from.
If you try upgrade across operator ,it will hang on boot loader screen.
And again, which 1.72 ROM did you try to upgrade from?
Hi,
I recently had a power cut (yes, a lights off power cut!) that killed my PC half wat through installing the Cingular English CWS__001 1.34.502.1 09/21/06 ?? 1.16.00.00 32.53.7018.01H 14955.2.3.0 ROM onto my SPV 3100.
Now SPV 3100 will boot to the ROM I was running prior to the upgrade but I can't use the telephone. I'm also not able to rerun the upgrade as it got far enough through the process to upgrade my bootloader to 1.06 - therefor rendering me unable to load another ROM.
Before the crash I was using the Imate ROM as below and M3100 was sim unlocked and running on o2 3G
i-mate English CDL__001 1.20.305.3 07/21/06 1.20.305.104 1.07.03.10 32.41.7010.02H 14955.2.3.0 1.04
Please help.
Thanks
If your device is still working ok as a PDA then hopefully it just screwed up the radio update of your device.
Try reflashing the Radio only
Look Here
http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms
Post back with results
Regards
S.K
EDIT: Sorry only works on 1.04 bootloader only. Afraid your gonna have to wait for Pof to come up with a 1.06-1.04 workaround
Hi S.K,
Thanks for the info. I have now tried installing the HERM_1.20.31.10_type2_radio_fixed upgrade but unfortunately the radio upgarde crashes also. It all seams to go well, (after using MaUpgradeUt_noID.exe twice) the phone says "Upgrade Radio Stack Please wait" and the progress bar appears on the PC but then after 10 mins I get an ERROR 114: RADIO ROM UPDATE ERROR.
Do you think this might be becuase the last upgarde partly installed bootloader 1.06?
Any other suggestions - I'm desperate to get the hpone on M3100 working again.
Thanks
Read here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
Please post USB monitor capture, otherwise can't help u.
Hi Pof,
Thanks for the offer, I will sort out the usb software on Monday. Are there specific actions that I should try, obvioosly I will usb monior everthing I do but I want to keep it to the point and not waist yr time trailing through huge log files.
Cheers
BTW - I have tried all options of recovery, such as attempting to install the latest radio and trying to install the new rom from an sd card, trying several roms and using imei unlocker - all without any joy.
I think the problem is that I have partially installed radio and bootloader 1.06 so I can't fix the problem.
Thanks again.
@wotthefok:
For me is faster to look at the usb log file, then I exactly know why the upgrade fails, otherwise I have to decode it from your feedback and I can't be really sure. Check the "upgrading problems" page on the wiki, if none of the steps there seems to fix your problem, post USB monitor log please.
Log Files as requested
Hi,
I have captured information using usb monitor and attached the zipped log files for your attention.
The first is called USB_monitor_log_Herm_120Radio_twice. This log details attempting to install the HERM_1.20.31.10_type2_radio_fixed upgrade, and running it twice - just in case.
The USB_monitor_log_runing_Cingular_1.34.502_11_uprgrade_twice.zip details attempting to install the RUU_HER_Cingular_1.34.502.1_1.16.00.00_wwe_cws_ship upgrade, simply using the standard ROMUpgradeUt.exe method. This generates the expected Vendor ID error.
My primary focus is to install the radio upgare or download my bootloader to 1.04. The PDA part of my m3100 does now freeze occasionally but at least functions whereas the phone is completely dead.
Thanks in advance.
Please attach capture in *ANSI TEXT FORMAT*, the .lgs file you zipped is totally unuseful
Edit -> Export and Save as type "ANSI Text files".
Also make sure you export in "COMPLETE" view, see the wiki for more details.
OK, Spot the novice.... I have now created a txt log file that captures activity of me running the 120 Radio upgarde - but only once this time. I still had to zip the file due to it's size. Hope this is OK.
I'll send the other logs within the next couple of hours. Please let me know if the output I have sent so far is acceptable?
Thanks
wotthefok said:
Please let me know if the output I have sent so far is acceptable?
Click to expand...
Click to collapse
No, it's a "basic" capture, you have to export a "complete" capture:
Start USBMonitor.
File -> New session -> USB Monitor -> Select USB device where your phone is connected -> Check "request view" -> Finish
In the upper part there are two tabs: basic and complete. Click on "Complete".
Right, Try again (duh!) OK, I've tried to keep the log files names as self-explanitory as possible... USB_monitor_log_Herm_120Radio_run1.zip is the r20 radio upgrade, 1st run and USB_monitor_log_Herm_120Radio_run2.zip the second run - without disconneting or resetting the device.
USB_monitor_log_runing_Cingular_1.34.502_11_uprgrade_ran_twice.zip is the Cingular upgrade run via the ROMUpgradeUt.exe, again run twice without disconneting the device.
Hope I got it right this time.....Please let me know if there is anything else I can do.
Thanks.
This time you got the captures right
- You're on bootloader 1.06: You don't have 'rtask' command, you won't be able to do any radio upgrade only.
- Your device is not CID unlocked (Security level=FF, unprivileged)
- The bad flash caused the CID area to corrupt (CID: Wait interpreter timeout)
- When flashing a full ROM you get a CID not allow (255) this is because your corrupted CID doesn't match the CID on the ROM.
The radio part is screwed, you could have fixed this if you where in bootloader 1.04 by flashing a full ROM, but as you are in 1.06 you can't because of CID checking. But you're lucky because the OS ROM is intact and you can boot the OS, you should be able to downgrade to bootloader 1.04 from OS and flash a full ROM after, which will hopefully fix your radio.
Just wait until a solution to downgrade bootloader is available (I'm working on it).
Hi,
As I suspected.... Suppose it's not all bad news though - just means that I have to be patient and use my communicator once more. Do you know if the guys at IMEI-CHECK have a downgrade solution? Even if it's a pay for option??
I have already got a IMEI-CHECK sim unlock from where I originally got the M3100 unlocked from Orange to work on o2. That said, I have run either unlocker 2 or 3 with the .unl that I know worked I now get
HTC HERMES v3c unlock
Starting communication.........
Checking device..............ERROR
The device you try to unlock is not supported.
Please contact your supplier site.
Device is rebooting
Press any key to quit this application.
I'm currently chatting to the guys at IMEI-CHECK re this problem.
Anything else I can do to assist you in anyway??
Cheers
wotthefok said:
Do you know if the guys at IMEI-CHECK have a downgrade solution? Even if it's a pay for option??
Click to expand...
Click to collapse
They have it (M3100v3cUnlock.exe), but it will not work on your device because your IMEI is corrupted and their unlocker will not be able to read it and to check/compare with the .unl key file.
Hi,
Just a quick update. The guys at MIGsofT LTD have VERY VERY generously said they'll have a look at the problem for me so my phone will be winging it's way to them today.
Thanks for your assistance and helping me be certain of the problem and to better understand the root cause.
Hope this information will prove useful to others.
Another quick update...
The guys at IMEI-CHECK (MIGsofT LTD) have rectified problems with my handset and managing to reinstall bootloader 1.04 in the process!!
They also turned my phone around in under three days and only charged me the cost of postage! I had previously been a customer of theirs but it was still a very generous and helpful offer and I would certainly pay for the service than have a duff handset - after all £250 + for a paperweight is rather excessive....
If you're experiencing a problem like mine why not get in touch with them and offer them money to have a look at your handset? No Guarantees but it seemed like my last chance, for a while anyway.
Praise to IMEI-CHECK for a brilliant service - they are King of the day !!
I was trying to upgrade to radio v1.43 in the hope that battery life was improved over 1.41 however when it got to 8% it stopped and gave me an error i can't remember After atempting to recover, it got off the three colour screen now the 3100 stalls on the blackshadow version4 screen (bootloader screen?) and goes no further. I tried reflashing but got a 260 and using mtty, only getting 2 com port options, didn't offer any help.
I'm really sorry to have not been able to sort this with reading through the relevant post but I haven't found a solution. What else can I try?
Hi,
Could you pls advise what is your device made, model, SPL version ... etc.
Also did you try to do Hard reset?
I'm using now black MAJIK (and few days ago black shadow) with radio 1.43 with no problem.
its the SPV m3100 When I decided to go Black shadow I read up on mr vanx and made sure I had all the things I needed. If I remember right, when I came to upgrade to Majik the auto detect found the second option down
SPL-1.04/1.10 - 1.09 Bootloader. I've realized since I had a spaz and ran the RUU from the archive this time. From what I've since read thats not too cleaver.
I have tried a hard reset and took the battery out instead of pressing space.
I dont know if this information on the starter screen is of use
M 05
S 04
B 05 D 3lak
I'm not sure, but hard reset doesnt mean you take the batery out.
Please check that link:
http://wiki.xda-developers.com/index.php?pagename=Hermes_For_Beginners#hardreset
I was in your position (hanged on booting) few days ago, and when i did hard reset, it changes every thing to basic normal condition.
i meant when i did a hard reset when it asked me to press space to reboot I took the battery out. I tried again this time pressing space to reboot but I still get stuck on the loading screen. I can't connect by USB to the PC I'm guessing the drivers on the phone haven't loaded and I'm stuck as to what to do.
Does anyone have any ideas?
try look at it http://forum.xda-developers.com/showthread.php?t=286755
ok I've tried everything I can think of to connect the 3100 to the computer so I can reflash it but mtty gives only com 1 and com2 but no USB and neither those two work, active sync wont connect so I disabled it as suggested and running the radio ruu and wrapper wont querry the device. I am now at a loss as to what to do next someone must know what I should do. Please?
what is your SPL?
try this http://wiki.xda-developers.com/index.php?pagename=HTC_Hermes
sl is 1.09 i'd updated it on the previously successful black shadow flash
msn [email protected]
icq 150277111
AIM TazmanFH9
Yahoo bigfathairyboggart
I have tried changing KITL trasport but I am unable to select or chose either option. I have also tried the rversion command in the tri colour screen but nothing happens. I hope I'm missing something nice and simple but I get the feeling I'm not going to be that lucky. Please help
tcSPVm3100 said:
sl is 1.09 i'd updated it on the previously successful black shadow flash
Click to expand...
Click to collapse
I suggest you check again, press and hold the side OK button and the power button...then put the stylus into the hole in the bottom of the unit.
yeah I've done that it's "SPL-1.09"
I had this exact problem yesterday, with the same bootloader too. The phone would not pass the splash and IT refused to upgrade. I ended up downgrading to a shipped wm5 rom (in my case the cingular 1.30.502.1_1.11.00.00) which to my surprise actually worked as no rom radio or spl upgrade moved at al on my phone. Then upgraded back to black majik. I hope this helps.
Thanks. I downloaded the trial of wm5 from the windows website and it asked me to install .NET framework version 1 so I got that but it turns out to be 2.0 not 1.1 It would say it had repaired but it would say this with or without the phone connected.
tcSPVm3100 said:
Thanks. I downloaded the trial of wm5 from the windows website and it asked me to install .NET framework version 1 so I got that but it turns out to be 2.0 not 1.1 It would say it had repaired but it would say this with or without the phone connected.
Click to expand...
Click to collapse
Just download a WM5 ROM from the wiki page!
ok tried this too no luck.
Trying to use the one from orange (linked to through wikki) I get an 294 invalid vendor error however active sync cannot connect yet of course so is this to be expected?
I have however gotten a connection with mtty which is a step forward dunno what to do with it yet though except trying the password 0000000000000000 command but it not disabling the password. This then lead me to read for a further hour how to change it and I've got to be honest; it beat me. I have No idea what the hell its talking about. My head hurt with so much reading.
I get a no gsm pop up v briefly on loader. I so want my phone back
I have since tried CID unlocker just so i get something installed onto this brick but I either get a connection error or it telling me it can't install for some other reason. I can not set the password in mtty to 0000000000000000 so how do I do that and is this the first step to getting things sorted? "just running a rom install" is not happening I can get a USB connection in mtty and that is it. Is the fact i'm running SPL 1.09 a problem? I'm getting precious little help guys If i'm posting in the wrong place or something please let me know. I need thing thing back now. Hours are drifting by with me trying to get some head knowledge but I still need some guidance please
tcSPVm3100 said:
I have since tried CID unlocker just so i get something installed onto this brick but I either get a connection error or it telling me it can't install for some other reason. I can not set the password in mtty to 0000000000000000 so how do I do that and is this the first step to getting things sorted? "just running a rom install" is not happening I can get a USB connection in mtty and that is it. Is the fact i'm running SPL 1.09 a problem? I'm getting precious little help guys If i'm posting in the wrong place or something please let me know. I need thing thing back now. Hours are drifting by with me trying to get some head knowledge but I still need some guidance please
Click to expand...
Click to collapse
can u flashing HARD V7?,i think better u have IPL 1.04 SPL 2.10olipro first ,then try to flashing radio?
and did u try SD card.
In bootloader can anyone here connect with active sync? I can't so updating rom and radio flashes in the usual way isn't possible. Trying the hard spl again it tells me to make sure active sync is connected and as it isn't it throws back a 262 update error. 0% on the hermes and that's currently as far as I can get. I have no means with which to access the memory card.
The reason you get an invalid vendor ID is because your CID doesnt match....download a ROM which is for your device (an orange one?)...then try.
You need to read the wiki alot more before trying anything else since you are not aware of the vendor ID error...nor the fact you MUST use HardSPL.
I linked to the orange ROM from wikki and tried installing it. it was while installing THIS ROM SPV_M3100_ROMUpdate_0407.exe I got invalid vendor error.
Installing a recent DL on HARD spl v7 I get a 240 open file error that's one I haven't had before.
With all other attempts they all say they want an active sync connection.
I can not connect to the phone through active sync
so all attempts by me to flash anything to the phone using an RUU fails.
I have a AT&T 8525. I installed 2.10 Olipro and then flashed with the latest AT&T WM6 upgrade from this site. It was labelled as the "official" upgrade.
The upgrade went well and everything seems ok (though it feels a bit more sluggish and I thought it would noticiabley increase speed of apps etc.)...anyway my Activesync is simply not working with this phone anymore. It doesn't recognize it when I plug in with the cable. This makes it hard for me to re-install a different ROM or any other app.
Bluetooth can see the phone, but, again, it doesn't seem to want to make an Activesync connection....please help...thanks in advance.
try deleting existing relationships. and create a new one. most likely because of your current upgrade, your DEVICE ID has been changed.
I actually have no relationships in Activesync right now.
I'm loading a fresh copy of Activesyn on my wife's computer to see if I can get a relationship established on a new install.
Any other ideas...I'm all ears!
you should be creating one.. its most likely because your DEVICE ID has been changed. have you checked it?
I have the same problem
The problem apears when I connect the device to the computer "USB Device Not Recognized".
Tested in another computer with same results...
It seems to be some driver issue, but I have no clue where to start...
I have a HERM200 (TyTN) unlocked and activesyn was working when the device OS was WM5. fter the upgrade, does not recognize anymore...
It's working now
After the OS upgrade, needs to turn off (for real) and turn on again. It works sweet.
Need to remember: MS Windows DEvices needs MS Solutions - Reboot !
I'm new on the forum, very informative but I could'nt find an answer to this situation. I have a HTC Advantage 7500 that originally came with mobile 5 on it and last year I successfully upgraded it to mobile 6. Couple of days ago I wanted to try something new so I upped it to 6.5 via a link on this site somewhere. The rom update went smoothly but I would like to go to 6.1 because for one the micro drive is not seen under the 6.5 that I have plus it has a slow response to screen manuvers and such. Now when I try to install mobile 6 or 6.1 it says please wait while the update takes place but my device restarts and the error #260 box comes up that says the update utility cannot connect to your PDA phone. Please check your USB connection. I would appreciate any help or suggestions. I know maybe I was wrong to try the mobile 6.5 on this. confused:
Since you are able to use 6.5, (it was a spl 3.5 version unless you
had found and used a spl 1.2) your phone should be having spl 3.5.
You need to search and download 6.1 spl 3.5 rom to change it.
Oh...Welcome!!
pdajoy said:
Since you are able to use 6.5, (it was a spl 3.5 version unless you
had found and used a spl 1.2) your phone should be having spl 3.5.
You need to search and download 6.1 spl 3.5 rom to change it.
Oh...Welcome!!
Click to expand...
Click to collapse
Thanks for your reply. I do now have the file 6.1 spl 3.5 but my device on 2 separate computers it just starts the update restarts my 7500 then the error message about USB connection. I didnt get this error the last 2 times I updated my device. Thanks in advance.
Taking it your pc (Windows XP) with anti virus and firewall disable.
Try flash back previous rom and have the device working first before going
any further.
Best to use same usb cable and port from same computer for your flashing. It helps to isolate problems in future.
Ensure device battery charge is above 60%, at least.
Remove SIM and memory cards before flashing.
I am sorry to hear that you're having problems with your device......however, the problem you've mentioned sounds quite familiar to me but I don't remember how I actually got mine fixed.
I have no idea what OS you're using but
try this:
re-installing activesync/device center then put your device in bootload mode (by holding down the camera button...fully....then press the reset button, keep holding camea button until the colored screen comes up. connect your phone to your computer and let it install the usb drivers.
after thats done, unplug, wait....replug and start up acticesync/device center make sure they're connected/synced then try changing the rom again.
hope that helps.
Thank you all so much. I did these things and it still restarts and goes right back in mobile 6.5 giving that same error message #260 box comes up that says the update utility cannot connect to your PDA phone. Please check your USB connection. Can it be a bad usb cable I'm using I wonder? Interesting my SPL version right now is 1.10.
that's the problem...your SPL should be 3.5 if you're on wm6.5. it is interesting that you got that instead of "invalid Model id" error. all in all I think the same method should solve your problem.
do a search for "invalid model id" and check out the post by cmonex she did a great job in creating a salutation. hopefully you had Hard SPLed your phone and that you had a home network that you had connected your phone so you can get back your phone's MAC address.
EDIT:
Also change your USB cable....I don't trust it, it's possible that it could be the problem. however, seen as your SPL isn't what it should be it the cable is not the problem (but change it anyway)
lennie said:
that's the problem...your SPL should be 3.5 if you're on wm6.5. it is interesting that you got that instead of "invalid Model id" error. all in all I think the same method should solve your problem.
do a search for "invalid model id" and check out the post by cmonex she did a great job in creating a salutation. hopefully you had Hard SPLed your phone and that you had a home network that you had connected your phone so you can get back your phone's MAC address.
EDIT:
Also change your USB cable....I don't trust it, it's possible that it could be the problem. however, seen as your SPL isn't what it should be it the cable is not the problem (but change it anyway)
Click to expand...
Click to collapse
Thanks so much! I will do this. I wonder why I have a spl 1.10? This is confusing with Win Mobile 6.5?
lennie said:
that's the problem...your SPL should be 3.5 if you're on wm6.5. it is interesting that you got that instead of "invalid Model id" error. all in all I think the same method should solve your problem.
do a search for "invalid model id" and check out the post by cmonex she did a great job in creating a salutation. hopefully you had Hard SPLed your phone and that you had a home network that you had connected your phone so you can get back your phone's MAC address.
EDIT:
Also change your USB cable....I don't trust it, it's possible that it could be the problem. however, seen as your SPL isn't what it should be it the cable is not the problem (but change it anyway)
Click to expand...
Click to collapse
I am using a new usb cable and the same thing happens. It says its starting to update the rom then it restarts my 7500 and error 260 comes up saying that it cannot connect to my device check your usb connection. I don't understand...