Related
Hello,
I bought the XDA IIs from a friend of mine in the U.K a month ago.
Everything works fine except that the STYLUS DOES NOT LOCK on to the groove provided behind the phone.
No matter how hard I push in it just would lock!!!
It was locking fine just an hour ago!!
After I charged the XDA IIs through a hotsync cable this problem seems to have arised.
Is there anything I can do at home to rectify the problem.
PLEASE PLEASE PLEASE HELP!!!
P.S - I have tried with a new pair of styli though and even they wouldn't lock in.!!!
Same problem here
I have learned to use it without the "pen". Losed two already!
nannlp said:
Hello,
I bought the XDA IIs from a friend of mine in the U.K a month ago.
Everything works fine except that the STYLUS DOES NOT LOCK on to the groove provided behind the phone.
No matter how hard I push in it just would lock!!!
It was locking fine just an hour ago!!
After I charged the XDA IIs through a hotsync cable this problem seems to have arised.
Is there anything I can do at home to rectify the problem.
PLEASE PLEASE PLEASE HELP!!!
P.S - I have tried with a new pair of styli though and even they wouldn't lock in.!!!
Click to expand...
Click to collapse
YES!!
:lol: Fingers work better than the PEN
AND leads to a form of exercise too... :wink:
The only drawback being while typing multiple letters get punched & b'comes a pain to delete them all :evil:
Re: YES!!
Could be VERY "handy" to have more "finger-optimized" options on the screen... I now really find the "stick" a ver slowww "extra". :roll:
nannlp said:
:lol: Fingers work better than the PEN
AND leads to a form of exercise too... :wink:
The only drawback being while typing multiple letters get punched & b'comes a pain to delete them all :evil:
Click to expand...
Click to collapse
finger optimization
huh !!! you could do something like a more finger friendly usage with XDA IIs!??? :shock:
How do you do that?
HELP!!!1
THANK YOU
Pockpctechs.com I thought had a fix for this?
I have this same problem but I just bought more replacement syluses and also make sure the device is in the normal position when I am wearing it.
Check www.pocketpctechs.com
what i did is open the back housing, put rubber sticker inside the place where stylus stay. now is tighter than before.
Hello
same problem, but realy easy to fix.
You have to use insulating tape (sorry, i don't know if this is the correct english name. This tape is used for insulating two elettrical wires connected togheter.)
So, you have to cut about 4mm x 1.5cm of this tape and then you have to turn around it on the top of your stylus.
This will produce a little gain of soft thickness right in the place where the stylus is in contact with your PDA.
My stylus slot was broken about one year ago: i used this insulating tape, and i have never lost my stylus.
follow some pictures... i have used white insulating tape in order to produce cleat photos: of course, you have to use black tape, as you can see in the last picture
Please try this link posted in wiki. This has details of how to fix a loose stylus.
http://wiki.xda-developers.com/index.php?pagename=BA_Sty_stopper
Regards
Sethuram
O2XDAiis
May need to modify length of tape, so experiment
Thank you Ronzino for this idea . I am now trying it out and it seems very good and yes, we do call it insulating tape in English btw, (at least in UK English).
I think it depends on the thickness of the insulating tape used, but I have found that I needed to cut the tape a bit shorter, for the stylus to fit. So it is worth experimenting on this.
I am guessing that the glue might soften in very hot weather, causing the tape to slide a bit, and make a bit of a mess, but this seems a minor problem compared to having to open uo my Blue Angel, which I reluctant to try. One can always clean up and use a fresh bit of tape.
I dare say it might be handy if manufacturers could perhaps produce stylus' in a way that overcomes this problem. One stylus I have seen has a small, rear springed, ball bearing inset on one side of it which would solve this problem. Unfortunately they do not seem to do these with the Blue Angel pecs in mind though.
almunday said:
Thank you Ronzino for this idea . I am now trying it out and it seems very good and yes, we do call it insulating tape in English btw, (at least in UK English).
I think it depends on the thickness of the insulating tape used, but I have found that I needed to cut the tape a bit shorter, for the stylus to fit. So it is worth experimenting on this.
I am guessing that the glue might soften in very hot weather, causing the tape to slide a bit, and make a bit of a mess, but this seems a minor problem compared to having to open uo my Blue Angel, which I reluctant to try. One can always clean up and use a fresh bit of tape.
I dare say it might be handy if manufacturers could perhaps produce stylus' in a way that overcomes this problem. One stylus I have seen has a small, rear springed, ball bearing inset on one side of it which would solve this problem. Unfortunately they do not seem to do these with the Blue Angel pecs in mind though.
Click to expand...
Click to collapse
This was suggested a while back (in fact, there was something about this in the wiki). For the most part, the section of the casing in charge of holding the stylus in place gets warped/cracked from use. Making the body of the stylus thicker allows the center to be locked rather than the top. Not sure about the glue, but for this to go bad, temps have to be rather high...
Instead of wrapping tape around your stylus, you can also take a 4x6mm piece of soft rubber and stick it inside the housing just behind the hook which should hold the pen.
You need 1,5mm material, if the hook is still there and you just want to improve the tightnes of your clasp, and 3-4mm if it is gone.
edit: replaced the missing clasp by using some piece of nylon- attached pic shows where i've taken it from. Glued this tiny part into the bay of the broken clasp and placed some mossrubber behind it as described above.
Works really good, and no tape smearing around in your housing
(Note: don't use cyanacrylate, it's like cancer to our housing...)
I'm wondering if anyone has considered modding the housing on their Wizard to change the colour, etc?
I've been looking at using Plasti-Kote to spray my housing black. They reckon it adheres to most surfaces including plastic (although maybe not pre-painted plastic). I'm not quite sure how smooth the finish will be. (If I fubar it I can buy a new housing for £40, although the missus wasn't impressed when I said so.)
If anyone else has done this, considered doing it, or has any other case mod ideas, let's hear about it!
Search for the thread for 'white wizard' pimp. that's nice.
Thanks for the pointer. Here's the thread:
http://forum.xda-developers.com/showthread.php?t=286863
That's pretty sweet. I'll take on board the advice to sand the housing first. I wondered if I'd just be able to paint directly over the top.
I think I would take my device apart too so I didn't have to worry about dust and paint getting somewhere it shouldn't.
Something else you could do and that I bet would look AWESOME would be to see if you could get it powder coated. I know there is a little shop up the road a few miles that has told me they would powder coat something in whatever color I wanted. Could allow for some interesting finishes. I'm picturing maybe some sort of glossy metallic finish or something.
Avatar28 said:
Something else you could do and that I bet would look AWESOME would be to see if you could get it powder coated. I know there is a little shop up the road a few miles that has told me they would powder coat something in whatever color I wanted. Could allow for some interesting finishes. I'm picturing maybe some sort of glossy metallic finish or something.
Click to expand...
Click to collapse
I am not familiar with powder coat. It looks like an interesting technique. According to this website you have to statically charge the item then bake the paint on?
I had also considered black with silver specks but ended up going for solid black in the end. (Maybe next time!)
* You can see my black wizard case mod here.
Usually when I buy RC car bodies they are Clear, you paint the inside to prevent scratching the paint, and it always looks great! Well I found this plastic case HERE Heck I am gonna order a couple and try a few different colors!!
I'd like a white wizard that's real glossy. I'd like the buttons to be white too, but I still want the buttons to display the letters and symbols. also i'm afraid the backlight wouldn't show through the keyboard. I think I have a delima huh?
You can use oven cleaner to strip the paint, just be sure to not leave it on very long or it will cause the top layer of plastic to shrink and crack. I haven't had to strip paint from plastic in a few years but I think it was about 30-40 minutes of soaking.
Regarding the powder coating, the piece to be coated is pretty much always metal because it must be baked in an oven.
Powder Coating wont work on plastic. It will just melt it within a few seconds of baking.
I just bought a wizard on ebay and also a separate case for it. My plan is to sand down the separate case and paint it with a matte black paint, I want to make it look like my macbook.
Yes so easy
See my Signature link PIMP My wizard and please post your jobs it will be nice see other jobs!!!
http://forum.xda-developers.com/showthread.php?t=427786
can someone help to open wizard's case with picture? all i can see 2 screws behind it which one of them is under stylus
I have a Wizard service manual but I can's seem to get it uploaded. If you know of another way to get it to you I will gladly send it along.
MDA or 8125 style?
On my signature see PIMP My Wizard link...???? it has a picture tutorial download it and check your screws maybe it shows right but,..... is for the Qtek 9100 or MDA Vario t-mobile design device.
Service manual:
http://rapidshare.com/files/164116696/HTC_Prodigy_Wizard-Service-Manual.pdf
After reading this and after having repaired my Wiz (came with a cracked screen to begin with) I'm going to take part of my next week (good to have vacation after all....) and use it to mod my Wizard's case. Well, hopefully if everything goes well, you'll see a pimped out Mod B_Edwa style here in a week...
Avatar28 said:
Something else you could do and that I bet would look AWESOME would be to see if you could get it powder coated. I know there is a little shop up the road a few miles that has told me they would powder coat something in whatever color I wanted. Could allow for some interesting finishes. I'm picturing maybe some sort of glossy metallic finish or something.
Click to expand...
Click to collapse
that is very good!!!
Ok so I bought a clear case here And while working, I was inspired by A black and silver Ford GT sitting in our shop. Here are the results.
that looks pretty good. may i ask where did you buy your case.
eBay
You can buy it from eBay a seller "e2" in Hong Kong, but shipping just about a full month. I bought 2 and am using none of them. They are garbage because the holders (places where plastic pieces stickout) will scratch your phone no matter what. Overtime, the places where the case is held on the phone will be pressed leaving the paint on the phone depressed and scratched. Otherwise it will protect the phone real good.
GQ8125 said:
You can buy it from eBay a seller "e2" in Hong Kong, but shipping just about a full month. I bought 2 and am using none of them. They are garbage because the holders (places where plastic pieces stickout) will scratch your phone no matter what. Overtime, the places where the case is held on the phone will be pressed leaving the paint on the phone depressed and scratched. Otherwise it will protect the phone real good.
Click to expand...
Click to collapse
They are not the highest in quality, and it took ten days shipping. But it sounds like you need to trim the "flash" around the tabs, you can also cut the tabs off and use little pieces of 2-sided tape, which will solve all of your mentioned problems.. for less than $5.00 and you can paint 'em any color you want, I ain't complaining!
http://cgi.ebay.com/Crystal-clear-c...ryZ48677QQssPageNameZWDVWQQrdZ1QQcmdZViewItem
VERY NICE PIMP! Very nice indeeed. an affortable and less dodgy way to do it
What paint you used? And sorry if I am blind, but you painted the cases you bought, not the phone itself, right ?
And BTW, looks ...WOOW
Nice job!
that reminds me of a friend of mine who once owned one of the cheapest polish cars (http://en.wikipedia.org/wiki/Polski_Fiat_125p) and painted id in similar way (actually he made quite lot of modding inside as well, including chrome-metallic parts that resembled washing machine in a way
oh well, there's been a lot of fun with this piece of junk... and the guy's nickname is still "Viper" ;]
oh yeah. i forgot to mention i like this mod a lot, looks very cool!!
anichillus said:
What paint you used? And sorry if I am blind, but you painted the cases you bought, not the phone itself, right ?
And BTW, looks ...WOOW
Nice job!
Click to expand...
Click to collapse
I am a Developmental Marketing Technician for Ford Motor Co. I pulled the "Paint Codes" from the door of the GT in the Third Picture. And used PPg enamel paint. I think any paint will work?! And yes I painted the inside. I screwed up the stripes (they should be wider and closer together). But I was in a hurry, I did it on my lunch hour, and still had time to eat! The paint looks really good!! The clear Plastic makes it look like a super thick clear-coat!! I spent a little time on a bench buffer with it. But the paint will never scratch, because it is inside!!
[HINT]
Oh yeah, a little Tip if you decide to try!!! After spraying the inside, no matter how well you mask it, you will end up with a mist of paint on the outside. A little polishing compound and a soft rag removes it like magic!!
Here is a Link to a picture of the case without the phone
congratulations
anione knows if this clear case exist for i- mate k-jam or qtek 9100??
COGRATULATION AGAIN YOU GIVE ME A GREAT IDEA
badbert said:
They are not the highest in quality, and it took ten days shipping. But it sounds like you need to trim the "flash" around the tabs, you can also cut the tabs off and use little pieces of 2-sided tape, which will solve all of your mentioned problems.. for less than $5.00 and you can paint 'em any color you want, I ain't complaining!
http://cgi.ebay.com/Crystal-clear-c...ryZ48677QQssPageNameZWDVWQQrdZ1QQcmdZViewItem
Click to expand...
Click to collapse
Pardon my poor language.. but what do you mean by "flash"?
Just dropped my phone a few hours ago and extremely upset... Luckily it was in its case but a coupla corners still got damaged
I was about to purchase a replacement housing but seeing this post, this would be a much cheaper alternative... Just gotta think of a theme now and find an artist...
Do you know if anyone sells it without that circle on the back?
Tsuioku said:
Pardon my poor language.. but what do you mean by "flash"?
Just dropped my phone a few hours ago and extremely upset... Luckily it was in its case but a coupla corners still got damaged
I was about to purchase a replacement housing but seeing this post, this would be a much cheaper alternative... Just gotta think of a theme now and find an artist...
Do you know if anyone sells it without that circle on the back?
Click to expand...
Click to collapse
Flash means when a plastic piece is cast, a small amount of plastic is left over that needs to be trimmed, or it could leave a jagged edge.
The circle on the back gives it a stable base when you lay the phone down...
could you share the gt theme?
inneyeseakay said:
could you share the gt theme?
Click to expand...
Click to collapse
Sorry I missed your post hope you enjoy it!!
man, why dont they sell these cases in the stores?????
that's a pretty damn good job, nice work!!
My wizzard 's casing is pretty beat up due to me dropping it, just laying it down on concrete, etc. I'm really thinking about actually sanding and 'polishing' the body of it to make it more shiny/get rid of scratches....and then buy a hardcase to go over that...
Wow... tahts the nicest case i've ever seen. Nice job... you should resell your case... =]
I did the same thing(well, solid black). It looks awsome from the front, but I cant get the back to really fit to the phone. I don't know if its my phone or if I just got a bad case.
I think I would have a little trouble returning it painted black though!
today my at&t tilt2 accidently fell from my hands and got heavily scratched on the chrome shell (bezel) the bezel even got few small dents & & the chrome colour came out
so i wanted to ask how can i remove this bezel,as i thought to remove it sand it & then paint it chrome again
& also suggest me is my idea good or not
no rplys? atleast tell me hw can i remove those scratches & dents
i wanna know this too since i just dropped mine today and its a fairly small chip but i still get a little crazy over it
please help us out
Sorry for bad news but to remove the bezel you'll need to fully dissassemble your TP2. You'll have to dismantle the main housing to unscrew hinges. Once you separate the upper part with LCD you'll be able to open it, and then separate the bezel from LCD and digitizer. I've done it myself couple of times but be aware that is not a 5 minute job (especially if you're new to this). You'll need tools - small philips screwdriver, small star screwdriver an special plastic prying tool (couple of them, they get broken easily, you don't have to use them but you'll most likely scratch the phone). You can get tool sets on ebay. Word of advice - if only possible try not to separate LCD and digitizer. Once you get dust and/or fingerprints between them it's a HELL of a job to get rid of them.
Check out mike channon's site for dissassembly guide.
Good luck guys!
EDIT: Personally, I would rather try to do some touch-up repairs without opening the phone if possible.
touch up repairs like what? suggest me something specific
I want to replace my screen and bezel but don't mind stripping the whole phone down if thats what is needed.
Try this link http://translate.google.co.uk/translate?u=http%3A%2F%2Fwww.pdacenter.ru%2Frazborka%2Fhtc_touch_pro2%2F&sl=ru&tl=en&hl=en&ie=UTF-8
As mentioned by pjm77 this does not look easy, and chances are if your not very careful you could mess up your phone.
By touch up I mean trying to paint the damage to make it less visible. Can't really say if that's possible in your case - judge for yourself. Dissassembling the whole phone is by all means possible, I was able to do it several times and I'm just an enthusiast. Just bear in mind that unless you're really skillfull and experienced you end up with a little damage here and there (clips broken, scratches etc.), it's time consuming and there is a risk of serious damage. In the end you may just put a lot of effort into it and be a little disappointed with the final result. But maybe not, it's up to you. Whatever your decision is - good luck!
EDIT: To be more specific I'll give you the real life example of touch-up. I had an awful, long and deep scratch on the back of my LCD (you can see that black, metal part when you slide out the keyboard). I took the masking tape and precisely shaped it in a way that only the scratch was visible (I'd say less than 0,5 of mm wide). Then I took a black paint (originally for my mother's renault) and painted the scratch. Aftrer half an hour I removed the masking tape. The repair is not perfect in any way, the scratch is still there if you know where to look. But I just never noticed it again and simply forgot about it until today.
I used a touch up pen from Staples that has metallic ink. It was a Silver Pilot Pen with Fine Point tip. Like pjm said, touch up paint isn't going to make it look perfect, but the scuffs on the chrome bezel are less noticeable. The ink is a little lighter than the chrome but makes the black cuffs disappear and is nice because you can get small marks with the fine point. I think it was $2.99.
Hi all,
Ok, so i've had a small disaster. As you probably guessed already i've dropped my phone. I thought the story was quite amusing (or just plain unfortunate!) so i'll you tell that before I ask for some advice!!
I got myself a white Galaxy S2 on upgrade through Vodafone. Gorgeous piece of kit so I ordered myself a nice case and screen protector to keep it nice and tidy.
Unfortunately the case got 'lost in the post' and as such the phone was unprotected. So, with some foresight I ordered a plain white cheap one off eBay (£2 inc. postage) just to see me through the 3-5 days I needed before the case I wanted was resent.
However what was sent what not white at all - it was the most hideous case with a rather disgusting floral effect all over it. I was going out for a night in town and had no choice, I had to take it with me.
Unfortunately later that eve I was stood at the bar, and my phone went off. So to save any embarrassment I slid the phone out of it's hideous case, and proceeded to read the message. Then it happened. The slippery son of a ***** jumped out of my hand, bounced off my foot and hit the deck.
It only has a couple of dings in the chrome bezel (the chrome effect rubbed off in two places to reveal black (the plating is obviously really thin)) - everything else was ok. Phew. But i'm still gutted and annoyed with myself
So, lesson learnt. I should have left the disgusting garish floral case on and it would have saved my phone. It was only 'de-sheathed' for a second and I managed to drop it, classic.
As a temporary solution, I coloured in the affected areas of the bezel with a silver permanent marker, and used some clear nail varnish over the top to stop the pen coming off. It seems to work well actually, and it looks much better than the black marks.
So, to my question - how do I change the chrome bezel for a new one?
I have read many threads, and watched many videos, and it looks to me like a nightmare job (eg as well as taking off the back and all components, you have to prise off the screen which is glued on, disconnect digitiser, etc). Can anyone confirm this, or has anyone tried it?
I can't find any videos of changing the bezel - they all seem to only go as far as taking off the back.
I've found a couple of sellers which sell the housing in white for only £20-30, so if it's an easy-ish job i'd have a stab at it. However i'm thinking I might as well just forget it ever happened and not be so precious about keeping the phone in A1 condition - it's a phone after all and it's going to encounter some scrapes now and then, even with a case on. And I plan on keeping it for 18 months anyway.
Opinions, anyone?
Cheers!
Movisman said:
Hi all,
Ok, so i've had a small disaster. As you probably guessed already i've dropped my phone. I thought the story was quite amusing (or just plain unfortunate!) so i'll you tell that before I ask for some advice!!
I got myself a white Galaxy S2 on upgrade through Vodafone. Gorgeous piece of kit so I ordered myself a nice case and screen protector to keep it nice and tidy.
Unfortunately the case got 'lost in the post' and as such the phone was unprotected. So, with some foresight I ordered a plain white cheap one off eBay (£2 inc. postage) just to see me through the 3-5 days I needed before the case I wanted was resent.
However what was sent what not white at all - it was the most hideous case with a rather disgusting floral effect all over it. I was going out for a night in town and had no choice, I had to take it with me.
Unfortunately later that eve I was stood at the bar, and my phone went off. So to save any embarrassment I slid the phone out of it's hideous case, and proceeded to read the message. Then it happened. The slippery son of a ***** jumped out of my hand, bounced off my foot and hit the deck.
It only has a couple of dings in the chrome bezel (the chrome effect rubbed off in two places to reveal black (the plating is obviously really thin)) - everything else was ok. Phew. But i'm still gutted and annoyed with myself
So, lesson learnt. I should have left the disgusting garish floral case on and it would have saved my phone. It was only 'de-sheathed' for a second and I managed to drop it, classic.
As a temporary solution, I coloured in the affected areas of the bezel with a silver permanent marker, and used some clear nail varnish over the top to stop the pen coming off. It seems to work well actually, and it looks much better than the black marks.
So, to my question - how do I change the chrome bezel for a new one?
I have read many threads, and watched many videos, and it looks to me like a nightmare job (eg as well as taking off the back and all components, you have to prise off the screen which is glued on, disconnect digitiser, etc). Can anyone confirm this, or has anyone tried it?
I can't find any videos of changing the bezel - they all seem to only go as far as taking off the back.
I've found a couple of sellers which sell the housing in white for only £20-30, so if it's an easy-ish job i'd have a stab at it. However i'm thinking I might as well just forget it ever happened and not be so precious about keeping the phone in A1 condition - it's a phone after all and it's going to encounter some scrapes now and then, even with a case on. And I plan on keeping it for 18 months anyway.
Opinions, anyone?
Cheers!
Click to expand...
Click to collapse
Sorry to hear...similar happened to my HTC Desire...however this should help...if you buy the kit off Ebay...
http://forum.xda-developers.com/showthread.php?t=1253969
0semaj0 said:
Sorry to hear...similar happened to my HTC Desire...however this should help...if you buy the kit off Ebay...
http://forum.xda-developers.com/showthread.php?t=1253969
Click to expand...
Click to collapse
Hi,
Thanks for the information - I had a look at this tutorial yesterday, and although it's very good, it looks like this person has replaced the entire led panel/digitiser/housing in one go, rather than just the housing?
My screen is just fine, so I only need to replace the housing part.
The hardest bit looks like separating the screen from the housing from what i've read, and this is what I can't find a tutorial for, only some images on youtube suggesting to use a hairdryer to help with the proceedings!!
Thanks
Movisman said:
Hi,
Thanks for the information - I had a look at this tutorial yesterday, and although it's very good, it looks like this person has replaced the entire led panel/digitiser/housing in one go, rather than just the housing?
My screen is just fine, so I only need to replace the housing part.
The hardest bit looks like separating the screen from the housing from what i've read, and this is what I can't find a tutorial for, only some images on youtube suggesting to use a hairdryer to help with the proceedings!!
Thanks
Click to expand...
Click to collapse
Yea, the link is for the whole unit, but would give you some pointers. I am not as familar with the Samsung build, but with the HTC I know that between the LCD housing and the LCD/digitiser itself is applied through adhesive (most phones are) that is put into a temperature oven for 10 minutes to soften the adhesive. This is based on the HTC Official Service videos. I am not sure if the same will apply to Samsung phones.
But then again, as it is an expensive phone, it may be ideal for you to also get a quote from your local SSC or mobile phone repair agent to consider.
0semaj0 said:
Yea, the link is for the whole unit, but would give you some pointers. I am not as familar with the Samsung build, but with the HTC I know that between the LCD housing and the LCD/digitiser itself is applied through adhesive (most phones are) that is put into a temperature oven for 10 minutes to soften the adhesive. This is based on the HTC Official Service videos. I am not sure if the same will apply to Samsung phones.
But then again, as it is an expensive phone, it may be ideal for you to also get a quote from your local SSC or mobile phone repair agent to consider.
Click to expand...
Click to collapse
Yep, good point. I'd be interested to hear actually what the cost would be to replace the front bezel only. It's only £30 on eBay for the front and rear housing, but i'd be willing to pay more on top for an authorised repairer to carry out the job.
That tutorial is definitely one of the more detailed ones I have seen so far though. Doesn't look like many people have tackled changing the bezel only...
Thanks
Movisman said:
Yep, good point. I'd be interested to hear actually what the cost would be to replace the front bezel only. It's only £30 on eBay for the front and rear housing, but i'd be willing to pay more on top for an authorised repairer to carry out the job.
That tutorial is definitely one of the more detailed ones I have seen so far though. Doesn't look like many people have tackled changing the bezel only...
Thanks
Click to expand...
Click to collapse
Hey Movis,
What did you end up doing for your dropped phone?
I too have dropped my phone on its corner and the chrome along with the plastic is now dented.
Another one with the same problem here. I managed to create a bump on the chrome bezel.
Can I bump this post as I've also just noticed a ding in the corner of the chrome bezel was wondering if anyone had found a solution to this yet.? short of replacing the LCD/digitiser which like OPs phone are working fine. It's just cosmetic damage.
I once was in a bad mood and snapped a screen and backing/housing in half.I can't remember exactly,but I'm thinking the chrome bit may be part of the thin metal casing/housing that is glue taped onto the screen.
You separate the screen from the housing by using a hot air gun sparingly.
If you look back at a motherboard thread I was involved in,a person on here called Roger put up a great video tutorial link that may answer all your questions...
Sent from my GT-I9100
Ah cheers for the reply. Had a look at the mobo post you were involved in followed it to the link and coincidentally that's the exact video I watched last night. Very good video good detail and instructions. But its the black one he is stripping down so he makes no reference to the bezel which afaik is only used on the white ones.
Sent from my GT-I9100 using xda premium
I've not seen the chrome bit listed separately,so I guess its part of the metal top housing that the LCD is glued to.I've got a white one and its got a ding on it too.
You could email Samsung to see if you can get the part,but I think its not worth risking cracking the screen and you probably couldn't resuse / would get that stupid gluey tape stuff.
Sent from my GT-I9100
Appreciate it's been a while, but this seems to be the only post that matches what happened to me, so figured I'd update with my experience.
As above, dropped and dented the bezel, screen was perfectly intact, but the dent was so severe, it actually lifted a corner of my screen up. I have intentions to sell on so I wanted to fix this and pass on.
I followed this disassembly , apart from the bit about not worrying about damaging the screen as you prise it away. The housing I ordered off ebay came with a little kit, so I warmed the screen with hairdryer for a couple of minutes, then slowly prised it away, from top to bottom, inserting the tool right down the middle as the video mentions there is a large adhesive right down the middle.
Following the vid all the way to the removal of all components, this is where I ditched my current bezel/housing and reassembled into the newly ordered one. Judging by the assembly, there is no way that a bezel could be replaced without replacing the housing, it's one whole unit, and I very much doubt the build would be that drastically different for the white SGS2.
Some things to note:
Be very careful removing the vibrate motor, the connector and natural pivot point is the weakest part (new module ordered from ebay
If you are transplanting the screen like me, have some adhesive pads in your kit as most tutorials are for new screens, and as can be seen on the vid, these come with pads intact, ready to apply
Try do it in daylight
Hope that helps anyone in a similar situation.
vyks10 said:
Appreciate it's been a while, but this seems to be the only post that matches what happened to me, so figured I'd update with my experience.
As above, dropped and dented the bezel, screen was perfectly intact, but the dent was so severe, it actually lifted a corner of my screen up. I have intentions to sell on so I wanted to fix this and pass on.
I followed this disassembly , apart from the bit about not worrying about damaging the screen as you prise it away. The housing I ordered off ebay came with a little kit, so I warmed the screen with hairdryer for a couple of minutes, then slowly prised it away, from top to bottom, inserting the tool right down the middle as the video mentions there is a large adhesive right down the middle.
Following the vid all the way to the removal of all components, this is where I ditched my current bezel/housing and reassembled into the newly ordered one. Judging by the assembly, there is no way that a bezel could be replaced without replacing the housing, it's one whole unit, and I very much doubt the build would be that drastically different for the white SGS2.
Some things to note:
Be very careful removing the vibrate motor, the connector and natural pivot point is the weakest part (new module ordered from ebay
If you are transplanting the screen like me, have some adhesive pads in your kit as most tutorials are for new screens, and as can be seen on the vid, these come with pads intact, ready to apply
Try do it in daylight
Hope that helps anyone in a similar situation.
Click to expand...
Click to collapse
Hi, will the heat actually damage the screen? I saw some posts mentioning about putting it into the oven and such. It sounded very intense but if it works without damaging the screen, i might give it a try. Facing the same situation as yours. Scratches and dents all over my front chrome bezel.