Did one T-Mobile 3.17.03 rom just fine. Have 2 with 4.01.16 and get error: get connection type an existing connection was fociblyclosed by the remote host. error getting connection type. xda-developer-ser v1.2
Programme v1.09
Ichecked the device manager-okay. Firewall off-anti-virus off swapped between 4 2.0 USB's and 2 1.1 USB's changed connection pods-no difference.
Anyone have any suggestions? :x
Have you ever tried a search here in the forum?
I guess not....
The T-Mobile ROMS (e.g. 4.01.16) prohibit downgrade via active sync. Try downgrading via SD-Card......
Stefan
Related
(Reposted from the thread dealing with the EEPROM issue)
2 days ago I upgrade my Dopod 838Pro to WM6. There were no issues experienced during the upgrade, but since doing it I have not been able to establish a connection to my AP. I have since downgraded back to the shipping version of WM5 in an attempt to get rid of this issue as I had no problems prior to upgrading.
One thing that I have found is that if I change my AP to be unsecured, using neither WEP nor WPA-PSK I can actually connect successfully, however as soon as I go back to WPA-PSK I again cannot establish a connection. I will try WEP next and post an edit with the results of WEP.
Update:
I have just tested WEP and it works also. Problem only seems to be with WPA-PSK security. Unfortunately I can't test any other APs - my router is a Netgear DG834T with the latest firmware on it. Does the Radio ROM version have anything to do with the WLAN/Wi-Fi/Wireless Adapter in my Dopod? I have no connection issue from 3 other PCs using WPA-PSK, the issues are specific to the 838Pro.
Device Information:
ROM version: 1.30.707.8
ROM date: 12/13/06
Radio version: 1.47.00.10
Protocol version: 32.80.7020.20H
I experienced this kind of issue where I work. There is a full wifi coverage and we can connect through WPA(2)-PEAP (mschap) or Open connection + VPN.
Since I updated to WM6, I was no more able to connect through WPA to the network. I connect fine to the open connection, but as I don't have the cisco vpn client on my hermes I cannot go any further.
I found no resolution to this; I asked the technical staff in-charge and all what they were able to tell me is that my handshake request doesn't even come to the RADIUS server.
At home I am also using wifi through WPA2 PEAP (cert) and it works fine. I had some issue at first (no connection possible with any WM devices I tested)with one of my access point, but updating its firmware had this fixed.
What you could try is to have your Access Point updated.
Let us know how you handle this issue.
One thing I noticed after upgrading was that wifi encryption defaulted to WPA2 with AES and I had to set it back to WPA-PSK and TKIP
I have a similar problem but i didnt upgrade to WM6 i upgraded to the latest Vodafone Rom.
I can connect to the internet via GPRS and whilst connected to my laptop via activesynch. but whenever i try to connect to my Netgear accesspoint it just sits at connecting untill it gives up. I am using wpa-psk too But it still doesnt connect when i remove all security
It worked fine before.
Not been able to test it on any other networks yet though.
any ideas i am running out
Rom: 2.07.161.1
rom date: 02/06/07
radio: 1.32
protocol: 32.65.7020.09h
i am expirencing the same issues on my Dopod 838 Pro running win mobile 5.0
My netgear router is set to WPA-PSK/TKP and other phones can connect to it.
However my dopod just sits on connecting and does nothing. If i try to surf the web my phone conect to GPRS instead of the wireless. Any ideas this is really frustrating??
I have problem with Wifi connection. I cannot get access to my Wifi AP (inside PC workstation: card Gigabyte).
I use HTC Athena with WM6 official HTC ROM (build 17745.0.2.3).
Beside Athena, I have on room others WM devices, and they are connecting to my Wifi AP without problems. For example Eten X500. I tried different authentication modes, WEP, WPA-PSK, nothing success. I'm sure all settings in Athena are the same as on my others devices. My AP is visible on Settings/Wi-fi dialog, and marked as "Available". but when I try to tap-and-hold this name, and select: Connect, then nothing will happen. It's displaying Connecting for a while, and then back to Available.
Is there any Wifi fix for HTC Athena?
I have the same Problem
I have an Imate JasJam and I am facing similar problems.
Here is what I have on my phone:
ROM - Black Satin
Radio - 1.43.00.00
IPL - 1.04
SPL - 1.20 Olipro
I recently flashed to this ROM image from the following web-site:
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=62&Itemid=26
At first it worked for about 3-4 days. Now all of sudden it has stopped working.
- I see that the WiFi connects to my access point.
- I can ping the device from my PC - so seems like it's fine on the internal network
- I have office communicator installed on the device - this seems to connect to my company server - I can see my colleagues online/offline
- On the other hand - Live Messenger does not connect, IE cannot view any site. Says "Page could not be found. Check the spelling and try again"
I wonder what went wrong.
Anyone seen this issue?
Wifi Problem wm6
Hi
The problems you have explained possibly caused by the driver update on the pc for the Wifi AP. Try uninstall the Ap and delete the settings from the Ameo, Then set up the device with WPA- TSK settings after reinstall the Ap with new drivers.
Good luck.
Actually, I could not figure what was going on. It surely was an issue with my device. Since my laptop(s) could connect just fine.
I did a hard reset - clear storage and the problem is gone.
I think it could have been due to some software installation on the device.
Now, question is which is that software. I will keep an out for this and see what happens each time when I install a new software on the device.
Hello, i'm trying to upgrade my device but facing a weird problem. The WMDC works fine and i can sync my device. When i run the RUU, it analyzes the rom and put the device in bootloader mode....
as soon as the device enters the bootloader, the usb loses the connection and says "cannot recognize the device" or "drivers not found" etc....and the RUU gives the error of "cannot connect to the device. make sure...."
I have tried this with the AthenaUnlocker as well as the AthenaWrapper. I'm currently on SPL 1.1 and want to upgrade to 1.2
Please help!
I have the same problem!
I want to install HSPL on my device. I cannot install this via SD Card so i tried it with USB. But after the bootloader the connenction was lost. Many times...
Can somebody tell me how to fix this problem?
Thanks
Edet: My device is a HTC HD2
This might not fit your problem, but ...
... try to connect your device to a PC/laptop with USB 1.1 - with my Ameo I have many "connection loss" problems with USB 2.0 speed, which occure only on heavy (data) load on syncing.
Disabling USB2.0 is possible on some machines within the BIOS.
If you got no PC/laptop with USB1.1 you can disable the USB 2.0 related driver in the Windows Device Manager (it works for me, in general). Therefor open the device manager and select the "View" menu -> devices by connection (or similar). Now search for the Athena entry attached to the listed USB hardware. Disable the "most-upper" USB controller the Athena is attached to.
OK, the last description might be confusing, but try.
Good luck (as this solution fits to your problem, as I am not sure)
What worked for me
junooni said:
Hello, i'm trying to upgrade my device but facing a weird problem. The WMDC works fine and i can sync my device. When i run the RUU, it analyzes the rom and put the device in bootloader mode....
as soon as the device enters the bootloader, the usb loses the connection and says "cannot recognize the device" or "drivers not found" etc....and the RUU gives the error of "cannot connect to the device. make sure...."
I have tried this with the AthenaUnlocker as well as the AthenaWrapper. I'm currently on SPL 1.1 and want to upgrade to 1.2
Please help!
Click to expand...
Click to collapse
I just spent the weekend trying to unlock my Athena and was having the exact same problem... USB would disconnect, errors 202, 267 . I finally was able to flash the Olipro bootloader, but had a hard time unlocking the radio. My device showed no radio under its properties, so I could not tell what radio version I had. Pressing "phone" would not bring the dialup screen. After so much sweat, I had to put it apart, only to find that the radio board connection to the motherboard was improperly seated, thus was having a bad connection. Once the connection was properly seated, the phone booted up to the emergency call screen, notified that there was no SIM card detected and when I looked in the device properties, the radio version was listed!. I then proceeded to unlock and flash the radio and this time the connection was not lost, the process completed without a glitch.
Hope that helps...
Hi everybody,
I got my new HD2 (original german Vodafone rom) last Friday and got it running very well if there wasn't that WLAN problem:
When connected to my Speedport W920V via WPA2 the phone does not get any access to the internet via WLAN. 3G works fine.
When I try to ping the phone the pings get back.
The strange thing is: Connecting to a friend's WLAN on a FritzBox get's me an access to the internet as well as an AdHoc connection to my laptop does.
What I tried since:
various hard- and softresets
deleting and setting it up again the wireless connection
removing any encryption on the accesspoint
updating HSPL with HSPL3
updating to 3.14 german original HTC
Nothing of that worked.
It would be great if you got some ideas for me!
Best regards from Germany
raid IO
one thing is important to know sir latest stock ROM (3.14) isn't compatible with HSPL.
it cause lot of troubles. so test it without HSPL on your stock ROM 3.14
Hi there,
i am running a HTC LEO Branded by Vodafone on Win Mobile 6.5 Professional.
Rom Version 3.14.162.5 (04666) GER
Radio 2.15.50.14
I was doing a Vodafone branded Rom-update 2 days ago.
Everything was fine just one thing went bad.
Before I was doing the update, I was connected with 2 wlan-server.
one server is based at home, one is based at work.
After the update I can´t see my wlan-server at work any more.
connecting with the server at home is allright and I also can see the wlan-servers of my neighbours but I can´t see my wlan-server at work even if I´m standing right in front of it. (On our laptops we can see the server and my friends also see the server with their smartphones).
Any Idea what I can do??
I tried to connect manually - no success
I tried to delete the connection - no success
I can´t even see the wlan-server in the list.
Is there any chance to change/delete something in the registry??
I tried to solve the topic with the help of htc but they have no idea because some server can be seen......
:-((
please help me!!
lastesel
The work one may be set to not show its SSID? meaning manually adding the network.