I have problem with Wifi connection. I cannot get access to my Wifi AP (inside PC workstation: card Gigabyte).
I use HTC Athena with WM6 official HTC ROM (build 17745.0.2.3).
Beside Athena, I have on room others WM devices, and they are connecting to my Wifi AP without problems. For example Eten X500. I tried different authentication modes, WEP, WPA-PSK, nothing success. I'm sure all settings in Athena are the same as on my others devices. My AP is visible on Settings/Wi-fi dialog, and marked as "Available". but when I try to tap-and-hold this name, and select: Connect, then nothing will happen. It's displaying Connecting for a while, and then back to Available.
Is there any Wifi fix for HTC Athena?
I have the same Problem
I have an Imate JasJam and I am facing similar problems.
Here is what I have on my phone:
ROM - Black Satin
Radio - 1.43.00.00
IPL - 1.04
SPL - 1.20 Olipro
I recently flashed to this ROM image from the following web-site:
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=62&Itemid=26
At first it worked for about 3-4 days. Now all of sudden it has stopped working.
- I see that the WiFi connects to my access point.
- I can ping the device from my PC - so seems like it's fine on the internal network
- I have office communicator installed on the device - this seems to connect to my company server - I can see my colleagues online/offline
- On the other hand - Live Messenger does not connect, IE cannot view any site. Says "Page could not be found. Check the spelling and try again"
I wonder what went wrong.
Anyone seen this issue?
Wifi Problem wm6
Hi
The problems you have explained possibly caused by the driver update on the pc for the Wifi AP. Try uninstall the Ap and delete the settings from the Ameo, Then set up the device with WPA- TSK settings after reinstall the Ap with new drivers.
Good luck.
Actually, I could not figure what was going on. It surely was an issue with my device. Since my laptop(s) could connect just fine.
I did a hard reset - clear storage and the problem is gone.
I think it could have been due to some software installation on the device.
Now, question is which is that software. I will keep an out for this and see what happens each time when I install a new software on the device.
Related
Here's the deal: I need help!!!!!!
I have a HTC TYTN and upgraded it's ROM from WM5 to Custels Ultimate WM6 as he got a lot of good reviews for it. However, there's a bug in it - apparently a bug Mr. Custel was aware of. After upgrading to WM6 my Active sync does no longer work when using USB.
Here's my details:
HERM200
spl-2.10 Olipro
IPL-1.04
Windows Mobile 6 Professional
CE OS 5.2.1238 (Build 17745.0.2.3)
ROM Version: CUSTEL Ultimate
ROM Date: 05/05/07
Radio version: 1.41.00.10
Protocol version: 32.74.7020.18H
I run Active sync 4.5 on my PC.
I have checked that the setting for Active sync is correct on my computer and that the 'Enable advanced network functionality' box is unchecked in the USB-to-Pc setting on my TYTN
I have tried to manually put my TYTN into Bootload to see if it can connect via USB then - and it cannot even if it says USB on my TYTN tricolor screen.
I've deactivated firewall, checked to see if settings for Outlook is correct etc... etc...
I've even tried to put a .nbh file on my SD card and put TYTN into Bootload mode - but it never got past the tricolor screen.....
In other word: I cannot connect my TYTN to my PC and I cannot flash another ROM onto my TYTN to make it work properly with Active sync.
What can I do? Any ideas would be appreciated.
Regards,
Njål
I will try
Well I had the same problem with active sync when I installed wm6 on my cingular 8525 (hermes). Once I figured out to remove the check in the USB to PC window, I removed activesync 4.5 and restarted my pc. Then I reinstalled activesync. I then restarted my pc. I then hooked the usb cable from the cradle that my phone sits in and then placed the phone in the cradle. Everything has worked fine since then. I know for sure that check in USB to PC has to be unchecked. It will not work unless. So try that and see what happens. That is what I had to do. It would not work until I unistalled and reinstalled activesync. Hope this helps.
A little more info:
Here's a little more info when it comes to my problem.
I've read the thread regarding Mr Custel's WM6 Final ROM and after I upgraded my phone, several others has complained about the same problem as I have.
Mr Custel has written that he's aware of the problem and that he will fix it - however, I now see a new ROM upgrade from Mr Custel called Custels Ultimate WM6 ROM. The problem is that I cannot install it since I cannot get an USB connection to work.
I've tried uninstalling Active sync - restart PC - reinstall active sync - restart PC and try to connect. Several times, actually. It doesn't work
Any ideas?
Regards, Njål
I have a AT&T 8525. I installed 2.10 Olipro and then flashed with the latest AT&T WM6 upgrade from this site. It was labelled as the "official" upgrade.
The upgrade went well and everything seems ok (though it feels a bit more sluggish and I thought it would noticiabley increase speed of apps etc.)...anyway my Activesync is simply not working with this phone anymore. It doesn't recognize it when I plug in with the cable. This makes it hard for me to re-install a different ROM or any other app.
Bluetooth can see the phone, but, again, it doesn't seem to want to make an Activesync connection....please help...thanks in advance.
try deleting existing relationships. and create a new one. most likely because of your current upgrade, your DEVICE ID has been changed.
I actually have no relationships in Activesync right now.
I'm loading a fresh copy of Activesyn on my wife's computer to see if I can get a relationship established on a new install.
Any other ideas...I'm all ears!
you should be creating one.. its most likely because your DEVICE ID has been changed. have you checked it?
I have the same problem
The problem apears when I connect the device to the computer "USB Device Not Recognized".
Tested in another computer with same results...
It seems to be some driver issue, but I have no clue where to start...
I have a HERM200 (TyTN) unlocked and activesyn was working when the device OS was WM5. fter the upgrade, does not recognize anymore...
It's working now
After the OS upgrade, needs to turn off (for real) and turn on again. It works sweet.
Need to remember: MS Windows DEvices needs MS Solutions - Reboot !
I'm following Mr Vanx's guide for upgrading my Jasjam from WM5 to WM6, but am having trouble with flashing the new bootloader onto the device. It's a second-hand telstra imate. I just bought it off ebay a couple of weeks ago and need to upgrade it to get it to read sdhc memory cards. I can't get it to connect to optus' (my mobile contract provider) mobile internet either, which I did via GPRS on my old phone. I'm hoping by upgrading the OS I can remove all of Telstra's code so It's not trying to connect to telstra's 3g network when I start the web browser.
When I get to the last step of the Hard-SPL installation, where the "updater will flash the new SPL and then restart your device (this will take generally less than a minute)" , the phone restarts almost immediately after clicking yes when prompted on the phone. The screen quickly goes to the bootloader screen, which says
"herm 100
IPL-SSPL by Des
Herm 100
SPL-1.09.ds"
The PC says that it can't connect to the phone and I should check the cable, which is still connected
The phone stays on the bootloader screen until I hit the soft reset, and WM5 boots like normal.
Has anyone else had this happen?
Yup,
Same problem over here. I had the problem before. But i fixed it! The only question is how did i do that? short term memory.
I'm trying to solve the problem. If its solved i will let you know.
Till then hang on
I've been trying again today. Still getting the same result, though I figured out if I just leave it when it gets to the bootloader screen, the pc I'm installing from eventually comes up with Error 260.
I'm thinking now that the XP firewall may be the issue, but I'm having trouble disabling it because it's managed by "group policies" (it's a work computer). I'm going to try either finding out which port to unblock, or starting the pc in safe mode so I can disable the firewall altogether.
I fixed the problem with the following softwaretool Hypercore. Just intergrate the Hard spl from olipro. After this the error dissapears.
Hello, i'm trying to upgrade my device but facing a weird problem. The WMDC works fine and i can sync my device. When i run the RUU, it analyzes the rom and put the device in bootloader mode....
as soon as the device enters the bootloader, the usb loses the connection and says "cannot recognize the device" or "drivers not found" etc....and the RUU gives the error of "cannot connect to the device. make sure...."
I have tried this with the AthenaUnlocker as well as the AthenaWrapper. I'm currently on SPL 1.1 and want to upgrade to 1.2
Please help!
I have the same problem!
I want to install HSPL on my device. I cannot install this via SD Card so i tried it with USB. But after the bootloader the connenction was lost. Many times...
Can somebody tell me how to fix this problem?
Thanks
Edet: My device is a HTC HD2
This might not fit your problem, but ...
... try to connect your device to a PC/laptop with USB 1.1 - with my Ameo I have many "connection loss" problems with USB 2.0 speed, which occure only on heavy (data) load on syncing.
Disabling USB2.0 is possible on some machines within the BIOS.
If you got no PC/laptop with USB1.1 you can disable the USB 2.0 related driver in the Windows Device Manager (it works for me, in general). Therefor open the device manager and select the "View" menu -> devices by connection (or similar). Now search for the Athena entry attached to the listed USB hardware. Disable the "most-upper" USB controller the Athena is attached to.
OK, the last description might be confusing, but try.
Good luck (as this solution fits to your problem, as I am not sure)
What worked for me
junooni said:
Hello, i'm trying to upgrade my device but facing a weird problem. The WMDC works fine and i can sync my device. When i run the RUU, it analyzes the rom and put the device in bootloader mode....
as soon as the device enters the bootloader, the usb loses the connection and says "cannot recognize the device" or "drivers not found" etc....and the RUU gives the error of "cannot connect to the device. make sure...."
I have tried this with the AthenaUnlocker as well as the AthenaWrapper. I'm currently on SPL 1.1 and want to upgrade to 1.2
Please help!
Click to expand...
Click to collapse
I just spent the weekend trying to unlock my Athena and was having the exact same problem... USB would disconnect, errors 202, 267 . I finally was able to flash the Olipro bootloader, but had a hard time unlocking the radio. My device showed no radio under its properties, so I could not tell what radio version I had. Pressing "phone" would not bring the dialup screen. After so much sweat, I had to put it apart, only to find that the radio board connection to the motherboard was improperly seated, thus was having a bad connection. Once the connection was properly seated, the phone booted up to the emergency call screen, notified that there was no SIM card detected and when I looked in the device properties, the radio version was listed!. I then proceeded to unlock and flash the radio and this time the connection was not lost, the process completed without a glitch.
Hope that helps...
Hi there,
i am running a HTC LEO Branded by Vodafone on Win Mobile 6.5 Professional.
Rom Version 3.14.162.5 (04666) GER
Radio 2.15.50.14
I was doing a Vodafone branded Rom-update 2 days ago.
Everything was fine just one thing went bad.
Before I was doing the update, I was connected with 2 wlan-server.
one server is based at home, one is based at work.
After the update I can´t see my wlan-server at work any more.
connecting with the server at home is allright and I also can see the wlan-servers of my neighbours but I can´t see my wlan-server at work even if I´m standing right in front of it. (On our laptops we can see the server and my friends also see the server with their smartphones).
Any Idea what I can do??
I tried to connect manually - no success
I tried to delete the connection - no success
I can´t even see the wlan-server in the list.
Is there any chance to change/delete something in the registry??
I tried to solve the topic with the help of htc but they have no idea because some server can be seen......
:-((
please help me!!
lastesel
The work one may be set to not show its SSID? meaning manually adding the network.