I'm following Mr Vanx's guide for upgrading my Jasjam from WM5 to WM6, but am having trouble with flashing the new bootloader onto the device. It's a second-hand telstra imate. I just bought it off ebay a couple of weeks ago and need to upgrade it to get it to read sdhc memory cards. I can't get it to connect to optus' (my mobile contract provider) mobile internet either, which I did via GPRS on my old phone. I'm hoping by upgrading the OS I can remove all of Telstra's code so It's not trying to connect to telstra's 3g network when I start the web browser.
When I get to the last step of the Hard-SPL installation, where the "updater will flash the new SPL and then restart your device (this will take generally less than a minute)" , the phone restarts almost immediately after clicking yes when prompted on the phone. The screen quickly goes to the bootloader screen, which says
"herm 100
IPL-SSPL by Des
Herm 100
SPL-1.09.ds"
The PC says that it can't connect to the phone and I should check the cable, which is still connected
The phone stays on the bootloader screen until I hit the soft reset, and WM5 boots like normal.
Has anyone else had this happen?
Yup,
Same problem over here. I had the problem before. But i fixed it! The only question is how did i do that? short term memory.
I'm trying to solve the problem. If its solved i will let you know.
Till then hang on
I've been trying again today. Still getting the same result, though I figured out if I just leave it when it gets to the bootloader screen, the pc I'm installing from eventually comes up with Error 260.
I'm thinking now that the XP firewall may be the issue, but I'm having trouble disabling it because it's managed by "group policies" (it's a work computer). I'm going to try either finding out which port to unblock, or starting the pc in safe mode so I can disable the firewall altogether.
I fixed the problem with the following softwaretool Hypercore. Just intergrate the Hard spl from olipro. After this the error dissapears.
Related
I was trying to upgrade to radio v1.43 in the hope that battery life was improved over 1.41 however when it got to 8% it stopped and gave me an error i can't remember After atempting to recover, it got off the three colour screen now the 3100 stalls on the blackshadow version4 screen (bootloader screen?) and goes no further. I tried reflashing but got a 260 and using mtty, only getting 2 com port options, didn't offer any help.
I'm really sorry to have not been able to sort this with reading through the relevant post but I haven't found a solution. What else can I try?
Hi,
Could you pls advise what is your device made, model, SPL version ... etc.
Also did you try to do Hard reset?
I'm using now black MAJIK (and few days ago black shadow) with radio 1.43 with no problem.
its the SPV m3100 When I decided to go Black shadow I read up on mr vanx and made sure I had all the things I needed. If I remember right, when I came to upgrade to Majik the auto detect found the second option down
SPL-1.04/1.10 - 1.09 Bootloader. I've realized since I had a spaz and ran the RUU from the archive this time. From what I've since read thats not too cleaver.
I have tried a hard reset and took the battery out instead of pressing space.
I dont know if this information on the starter screen is of use
M 05
S 04
B 05 D 3lak
I'm not sure, but hard reset doesnt mean you take the batery out.
Please check that link:
http://wiki.xda-developers.com/index.php?pagename=Hermes_For_Beginners#hardreset
I was in your position (hanged on booting) few days ago, and when i did hard reset, it changes every thing to basic normal condition.
i meant when i did a hard reset when it asked me to press space to reboot I took the battery out. I tried again this time pressing space to reboot but I still get stuck on the loading screen. I can't connect by USB to the PC I'm guessing the drivers on the phone haven't loaded and I'm stuck as to what to do.
Does anyone have any ideas?
try look at it http://forum.xda-developers.com/showthread.php?t=286755
ok I've tried everything I can think of to connect the 3100 to the computer so I can reflash it but mtty gives only com 1 and com2 but no USB and neither those two work, active sync wont connect so I disabled it as suggested and running the radio ruu and wrapper wont querry the device. I am now at a loss as to what to do next someone must know what I should do. Please?
what is your SPL?
try this http://wiki.xda-developers.com/index.php?pagename=HTC_Hermes
sl is 1.09 i'd updated it on the previously successful black shadow flash
msn [email protected]
icq 150277111
AIM TazmanFH9
Yahoo bigfathairyboggart
I have tried changing KITL trasport but I am unable to select or chose either option. I have also tried the rversion command in the tri colour screen but nothing happens. I hope I'm missing something nice and simple but I get the feeling I'm not going to be that lucky. Please help
tcSPVm3100 said:
sl is 1.09 i'd updated it on the previously successful black shadow flash
Click to expand...
Click to collapse
I suggest you check again, press and hold the side OK button and the power button...then put the stylus into the hole in the bottom of the unit.
yeah I've done that it's "SPL-1.09"
I had this exact problem yesterday, with the same bootloader too. The phone would not pass the splash and IT refused to upgrade. I ended up downgrading to a shipped wm5 rom (in my case the cingular 1.30.502.1_1.11.00.00) which to my surprise actually worked as no rom radio or spl upgrade moved at al on my phone. Then upgraded back to black majik. I hope this helps.
Thanks. I downloaded the trial of wm5 from the windows website and it asked me to install .NET framework version 1 so I got that but it turns out to be 2.0 not 1.1 It would say it had repaired but it would say this with or without the phone connected.
tcSPVm3100 said:
Thanks. I downloaded the trial of wm5 from the windows website and it asked me to install .NET framework version 1 so I got that but it turns out to be 2.0 not 1.1 It would say it had repaired but it would say this with or without the phone connected.
Click to expand...
Click to collapse
Just download a WM5 ROM from the wiki page!
ok tried this too no luck.
Trying to use the one from orange (linked to through wikki) I get an 294 invalid vendor error however active sync cannot connect yet of course so is this to be expected?
I have however gotten a connection with mtty which is a step forward dunno what to do with it yet though except trying the password 0000000000000000 command but it not disabling the password. This then lead me to read for a further hour how to change it and I've got to be honest; it beat me. I have No idea what the hell its talking about. My head hurt with so much reading.
I get a no gsm pop up v briefly on loader. I so want my phone back
I have since tried CID unlocker just so i get something installed onto this brick but I either get a connection error or it telling me it can't install for some other reason. I can not set the password in mtty to 0000000000000000 so how do I do that and is this the first step to getting things sorted? "just running a rom install" is not happening I can get a USB connection in mtty and that is it. Is the fact i'm running SPL 1.09 a problem? I'm getting precious little help guys If i'm posting in the wrong place or something please let me know. I need thing thing back now. Hours are drifting by with me trying to get some head knowledge but I still need some guidance please
tcSPVm3100 said:
I have since tried CID unlocker just so i get something installed onto this brick but I either get a connection error or it telling me it can't install for some other reason. I can not set the password in mtty to 0000000000000000 so how do I do that and is this the first step to getting things sorted? "just running a rom install" is not happening I can get a USB connection in mtty and that is it. Is the fact i'm running SPL 1.09 a problem? I'm getting precious little help guys If i'm posting in the wrong place or something please let me know. I need thing thing back now. Hours are drifting by with me trying to get some head knowledge but I still need some guidance please
Click to expand...
Click to collapse
can u flashing HARD V7?,i think better u have IPL 1.04 SPL 2.10olipro first ,then try to flashing radio?
and did u try SD card.
In bootloader can anyone here connect with active sync? I can't so updating rom and radio flashes in the usual way isn't possible. Trying the hard spl again it tells me to make sure active sync is connected and as it isn't it throws back a 262 update error. 0% on the hermes and that's currently as far as I can get. I have no means with which to access the memory card.
The reason you get an invalid vendor ID is because your CID doesnt match....download a ROM which is for your device (an orange one?)...then try.
You need to read the wiki alot more before trying anything else since you are not aware of the vendor ID error...nor the fact you MUST use HardSPL.
I linked to the orange ROM from wikki and tried installing it. it was while installing THIS ROM SPV_M3100_ROMUpdate_0407.exe I got invalid vendor error.
Installing a recent DL on HARD spl v7 I get a 240 open file error that's one I haven't had before.
With all other attempts they all say they want an active sync connection.
I can not connect to the phone through active sync
so all attempts by me to flash anything to the phone using an RUU fails.
Alright so I am so frustrated with this...and I am sure there is a simple solution for it. The screen on my old 8525 got messed up and since it was under waranty they sent me a replacement...the screen is ok on the replacement, but the phone isn't working (shows exclamation point next to "wine glass" rather than signal strength bars).... after hours and several phone calls to tech support, High End Devices waranty dept and who knows where else, it was determined that the current ROM version is incompatible with the AT&T network, I have to upgrade. So the version of the ROM on the replacement is 2.15.502.3 which makes wonder why in the world would AT&T send me a phone that would not work on their network? (I'm really trying not to vent here...) Anyways so I go to the HTC website as directed by the Tech. Support person download the stuff and after another hour on the phone with HTC and every possible sollution that they know is tried still can't install. I am running a Vista 64 machine and after getting around all the Vista quirks I am finally able to get to the Bootloader screen (button combination is: Side button [Ok] + [Power] Then push [Reset]...if done correctly your phone goes to the 4 bar boot loader screen, if not your phone soft resets and you have to try it again...) anyways in the bootloader screen it goes to the installation bar on both phone and PC and goes to 1%, then durring that one percent I get the horrible "ERROR 294 : INVALID VENDOR ID" on the PC and the Phone resets.....No matter how we have tried it it is always the same thing...redownloaded the file 3 times, restarted the phone about a gazillion times and the PC about 2 or 3 times. What can I do? I would love to have Ms Windows Mobile 6, but all I really want is a working phone....can anyone please help?
Some more info for those of you that can help:
On "Device Information" screen here is what I have:
ROM version: 2.15.502.3
ROM Date: 04/09/07
Radio version: {blank}
Protocol version: {blank}
On Bootloader screen:
In the top (red) section:
(in white)
HERM100
IPL-1.03
(in yellow)
HERM100
SPL-1.11
and then at the bottom (white) section:
(in black)
USB
(it says Serial when I unplug the USB cable)
I am trying to install the ROM titled:
RUU_Hermes_CINGULAR_WWE_3.62.502.3_6275_1.54.07.00_108_UOOS_SVN05_Ship.exe
downloaded from:
http://216.139.227.230/download/Sof...502.3_6275_1.54.07.00_108_UOOS_SVN05_Ship.exe
found by going to http://www.htc.com, Support, AT&T 8525, Software Download.
Thank you for any help you can give.
u cant be serious......you got an invalid model ID from an 8525 while trying to install an update from at&t itself.
well the solution would simply be to install hardspl (see the sticky) and then install the update. although there are many other easier and faster solutions i think this is the *safest* way. but then the fact that your radio version shows nothing makes me wonder......maybe a corrupted radio or something, which may or may not be related to the invalid model ID error.......anywho, search the forums for error 294 its probably been discussed many times
First of all thanks for your help. So I tried installing the 2.10 - Hard-SPL-V7 and it wont finish the install. I connect the device follow through the installation and when I get to the point where I push Yes on the 8525 the screen goes to the red/green/blue/white bars screen shows
HERM100
IPL-SSPL by Des
HERM100
SPL-1.09.ds
then the Computer shows ERROR [260]: UPDATE ERROR and the installation stops....
error 260 is an open port error, reboot your computer, and try again, if it doesnt work, try a different usb port, also disable watever firewalls or antivirus software you have
Okay so I diabled both the firewall (Windows Firewall) and the antivirus (AVG) and restarted the computer...tried 3 different USB ports...still the same problem....You don't think it could have anything to do with Windows Vista 64 and Windows Mobile Device Center. BEcause as soon as I go into the new Bootloader screen, the WMDC shows that the 8525 is diconnected now...even though it's not. I saw a post on here about installing drivers to get Active Sync on a Vista machine, but the drivers it provides are unsigned and Vista won't let me load them....so what's the next step? And again thank you so much for your help.
Is there any use in putting more effort into this or should I just have AT&T send me a new one?
whether there's any use left is ur decision, dont ask me to help you make your decision.
i know you can install unsigned drivers on vista, i dont know how, use the search. i have also heard that updating wmdc to the latest version helps too.
or you can either try and install hardspl using the microsd card, again use the search.
I need some expert help please! I have a Hermes (Orange SPV M3100) that I want to flash with a custom ROM but I am having a problem with ActiveSync losing the USB connection at the point that the device enters the bootloader screen. I am also unable to flash using the SD card method. I have flashed a Nike without any problems and I'm usually good with technical stuff so I think there must be something extra I need to do that I have missed. I hope that somebody can spare the time to help me solve the problem. Here are the details:-
I am trying to follow Mr Vanxs guide to flashing the ROM in windows Vista so that I can upgrade it from WM5 to WM6 and apply a custom ROM to load a new TouchFlo style OS. The first step in this process is to flash HardSPL using this guide but my problem with the USB connection won't let me do that. I have unlocked the device using Hermes Unlocker 3a so it is (or should be) SIM and CID unlocked and be SuperCID with HardSPL-1.40 (so maybe I can miss the Mr Vanxs HardSPL step?).
So, when I run the RUUWrapper.exe, choosing the Force option and accepting the messages I eventually get a prompt on the device. At this stage ActiveSync is connected. I click Yes on the device and it enters the bootloader screen which shows 'USB' on the tri-color screen but ActiveSync immediately drops the USB connection. The update then waits for a while then fails with Error 260. I have to do a soft reset to get the device out of the bootloader screen. When the device reboots the Activesync connection comes back to life.
I thought that I maybe don't need to HardSPL first so I tried just going straight to the ROM upgrade but I get the same problem.
Also, I tried following this link to flash using the SD card instead of USB but when I get to step 6 I don't see a confirm message - just the usual bootloader screen (it doesn't help that the screen shot doesn't appear on the link so I'm not even sure if I'm getting the correct screen). Any ideas?
I realise that an answer to this probably already exists somewhere on the forum but I have spent hours trawling through posts and I can't find it so I hope somebody has come across this before and can help me out.
Thanks guys!
Don't worry I solved it by rebooting my PC, skipping the HardSPL and flashing with an official ROM (HTC_TyTN_WWE_3.54.255.3_6275_1.48.00.10_108). I can now apply custom ROMs.
Am having a problem with unlocking a Hermes using the SIM_CID Unlock version 3A
I appear to be stuck in a loop with the unlock process. I appear to have got as far as having installed OliPro (while still being at bootloader 1.01) but keep getting error 262 UPDATE FAILED
I can then recover to the tri-colour screen and process as far as RECOVERY SUCCESSFUL
But I cant get as far as updating the radio or whatever else it unlocks towards the end of the process and no new ROM loads (if that is what the unlocker does?) The percentage screen appears but doesnt progress at all. Then I get ERROR 262 again.
Is starting to the bootloader screen a sign of a bricked Hermes? I can get SERIAL to show and can get it to change to USB on that screen when I plug it into a computer but cant get any proper communication with the unit from the computer with that screen in place: ActiveSync obvoiusly wont start. As I left the 3A unlocker, it said RECOVERY SUCCESSFUL but does that necessarily mean that I have a brick now? I thought that the installation of olipro by SIM_CID unlock version 3A means that the unit is now hard-unlocked?
(Yes, I did try Hard-SPL-V7.zip but cant set up any communication between the exe file and the tricolour screen)
If you are using XP, untick "Allow USB Connections" in activesync. Put Hermes into bootloader and connect to PC. Run RUU_Wrapper.exe. Should fix the problem.
I thought that tricolour screen meant that it is ONLY starting in bootloader mode?
ultramag69 said:
If you are using XP, untick "Allow USB Connections" in activesync. Put Hermes into bootloader and connect to PC. Run RUU_Wrapper.exe. Should fix the problem.
Click to expand...
Click to collapse
I am a bit lost: How do I get into bootloader mode? I thought that it starting in the tricolour screen meant that it had started up in boot loader mode? Is there some combination of pressing buttons and 'on' switches like on my Blue Angel?
As it appears to have got stuck in a mode while in an upgrade process which didnt work when this error occurred, when I get it started, what should I flash to get the bootloader updated, the SIM and CID unlocked so that I can choose which ROM to flash? Should I continue with the SuperCIM_CID unlock or Hard SPL?
I have fully unlocked another Hermes before and have been playing around with ROMs but this one seems to have worked out differently: I was under the impression that loading OliPro meant that it was unlocked?
(Sorry about that answer: I will try RUU_Unwrapper.exe again)
ultramag69 said:
If you are using XP, untick "Allow USB Connections" in activesync. Put Hermes into bootloader and connect to PC. Run RUU_Wrapper.exe. Should fix the problem.
Click to expand...
Click to collapse
I did what you said and immediately I unchecked the tick in USB, I heard that the computer was establishing communication with the Hermes
But nothing I could do would let RUU_Wrapper.exe Run and communicate with the device. It just kept reporting NO DEVICE.
So I tried the super SIM and CID unlock again and it tried installing OliPro again and couldn't do so, saying that (having communicated with the device) it couldn't communicate with the device either. I tried retrying a few times with no success and pressing NO with equally no success. So I tried canceling out of the application. it thought about it for about three minutes and then simply started communicating, running the upgrade program. Now it starts the update process and I can see the progress.
However it stops at 21% and doesn't move any further. It has been that way for a few hours now. not sure if it is charging while connected, I suspect not and am wondering what to do now which wont brick the unit??
V7 still wont run but v3A still will!
ultramag69 said:
If you are using XP, untick "Allow USB Connections" in activesync. Put Hermes into bootloader and connect to PC. Run RUU_Wrapper.exe. Should fix the problem.
Click to expand...
Click to collapse
So I tried the super SIM and CID unlock again and it tried installing OliPro again and couldn't do so, saying that (having communicated with the device) it couldn't communicate with the device either. I tried retrying a few times with no success and pressing NO with equally no success. So I tried canceling out of the application. it thought about it for about three minutes and then simply started communicating, running the upgrade program. Now it starts the update process and I can see the progress.
However it stops at 21% and doesn't move any further. It has been that way for a few hours now. not sure if it is charging while connected, I suspect not and am wondering what to do now which wont brick the unit??[/QUOTE]
This is getting curiouser and curiouser: This device both will and wont coopeate at the same time. But nothing I could do would let RUU_Wrapper.exe Run and communicate with the device. It just kept reporting NO DEVICE on error 260\.
So I tried the super SIM and CID unlock again and it tried installing OliPro again and couldn't do so, saying that (having communicated with the device) it couldn't communicate with the device either. I tried retrying a few times with no success and pressing NO with equally no success. So I tried canceling out of the application. it thought about it for about three minutes and then simply started communicating, running the upgrade program. Now it starts the update process and I can see the progress.
However it stops at 21% and doesn't move any further. It has been that way for a few hours now. not sure if it is charging while connected, I suspect not and am wondering what to do now which wont brick the unit??[/QUOTE]
This is getting curiouser and curiouser: (Especially if you arent too petrified about bricking it) I can perform the recovery successfully from whatever I do but cant get v7 to communicate with the device. However 3A DOES still communicate but still gets stopped at 0% on the progress chart. Is this a known problem, that SuperSIM_CiD wont work with OliPro already installed at 1.40? That it WILL get stuck at 0% or 21%?
Now I cant hard reset either: I dont get the white screen, it just goes back into the bootloader, still showing IPL 1.01 and SPL 1.40 Olipro.
(Especially if you arent too petrified about bricking it) I can perform the recovery successfully from whatever I do but cant get v7 to communicate with the device. However 3A DOES still communicate but still gets stopped at 0% on the progress chart. Is this a known problem, that SuperSIM_CiD wont work with OliPro already installed at 1.40? That it WILL get stuck at 0% or 21%?
Now I cant hard reset either: I dont get the white screen, it just goes back into the bootloader, still showing IPL 1.01 and SPL 1.40 Olipro.
The computer IS communicating with the device (as I said it does give the 'ding' showing that the computer knows it is there) but it wont hard reset! It just goes straight to the tricolour screen immediately on startup. Even using a three hand method of pressing both buttons, pushing the reset in and putting the battery in at the same time gave the tricolour screen. And Windows Explorer cant get into the device. It seems to see it but there is no tree at all. So I cant use the Post 1160 method to flash from an SD card.
Even more baffling, i have now flashed a stock ROM successfully and v7 STILL wont communicate with the Hermes!! In desperation I even moved the directory to the root of C: Are some of these devices encrypted differently from others? So suddenly it boots properly and I immediately did a hard reset and erased everything and now Guess what? It hangs at the Windows Mobile screen! Needing a hard reset all over again
Should I just keep on trying Super SIM and CID unlock again and again until it works? (I assume that I have no longer got OliPro on it, though it does show a SPL of 1.40) There must be a way of unlocking this unit but this total non-cooperation doesn't seem to be covered in the Wiki. Is there a version of the Hermes like the Wizard which is more difficult to unlock than the others?
Sorry to reply again when no one gave any ideas on my last posting but I am wondering, horror of horrors, whether this might be a hardware problem?
I am now stuck at the tricolour screen ( 1.01, SPL 1.40.Olipro)) which turns on whenever I put the battery in. Connecting to the computer doesnt make any difference and obviously I keep getting ERROR 260 which seems to be a connection error meaning that the computer either isnt connected to the device (or that some software is conflicting somewhere, which is unlikely as flashing to the stock ROM did work before I tried to run V7 again)
Is there any possibility that running SuperCID&SIM unlock (which has never completed) caused all of this and is there any rescue procedure or should I just assume that this is a hardware problem now (or should I do a fresh posting)?
Is it inherently suspicious that tricolour turns in when I just put the battery in AND that even though SERIAL changes to USB on the Hermes, running the v7 hard update utility causes ERROR 260? [Or cant you run V7 when you already have OliPro installed somehow?]
There IS communication: Though I reported in my last posting that I could flash the Cingular ROM, flashing to the Cingular ROM now gets consistently stuck at 14%, sometimes with an ERROR 264!
Hello Everybody,
My mobile at&t 8525 alias HTC 8525 is stuck in windows operator logo.It would not boot further. It happened while I tried to upgrade it from Windows 5.0 to Windows 6.0.First I got a tri-colour screen,but in a hurry I tried to backgrade to windows 5.0 again.
Other problem the mobile cannot be synced. I have installed Microsoft Active sync 4.5. Even then it could not be synced.
I tried to read all the posts ,but could not understand anything.
So please help me in getting my mobile repaired
Don't worie.
I had somewhat the same issue with a bad ROM flash.
Just disconnect the USB and boot to the bootloader screen (the tricolour screen) and you should be able to reflash the phone again.
Problem in syncing the mobile
I am not able to sync the mobile to the laptop.I have installed Microsoft Active sync 4.5. Even then it is not syncing.So how could I run the hermes upgrade if the mobile is not helping.
Please help
In Activesync on PC - Untick "Allow USB Connections".
Put the Hermes into bootloader (tri-colour screen) and connect by usb. Run the RUU_Wrapper.exe file you want. Follow onscreen instructions.
You need to have installed Hard SPL V7 for this to work...
did not work
Hello Boss
I tried to follow the procedure you suggested me. but it did not work. I tried with Hard SPl 7.0.
Please give me some suggestion
you dont need an active sync connection to flash it. Enter bootloader(tri colour screen) as you were told in the previous posts and Just click on the boxes that you do have a connection(even though you dont) and then flash the rom.
@ultramag69 i hve never had to untick allow usb connections and i have cocked up loads of rom flashes, saying that i have never had a problem flashing in vista either so maybe i am lucky
If you still cant flash doing it this way, then maybe you should try flashing from sd card instead, just make sure the battery is fully charged. Full instructions of how to do this are found in the hermes wiki, which i advise you to read anyway.
Oh and good luck anyway, you should be able to recover the phone from this ,so i wouldnt fret too much
Guess he isnt hardspl'ed... then his batt is death... must to flash a shipped rom.
correct me if im wrong.
Problem with upgrade At&T 8525 mobile
Hi!
I'm having problems with my Cingular 8525, after I made the upgrade to WM6.1 (FARIA-R32-XDA2_WM6.1.rar) for WM 6.5 (FCWs_stock_like_6.5_v3.rar), and slowed my device does not work anymore. He died.
I need help please. How resurrect it?
Excuse my English.
english is not the problem here cause we need more info... device info SPL IPL hardSPL? you go from 6.5 to 6.1?
Do you try to flash first the Stripped?
Does your batt has charge enough to boot?
There are many many things to say so... start to tell us all your history!
Hi
I tried to Hard spl with Hard Splv7. But I got a error. I even tried the Sd Card method.Its says loading and I get the tricolour mode. If I press the Power button its not showing the status of upgradation.
Where can I get a shipped rom. Actually my Spl is 1.11.
Hi
I tried to Hard spl with Hard Splv7. But I got a error. I even tried the Sd Card method.Its says loading and I get the tricolour mode. If I press the Power button its not showing the status of upgradation.
Where can I get a shipped rom. Actually my Spl is 1.11.
check the wiki pages for your device in the upper bar of this web forums
there are many official roms.
I also am currently using an 8525 (Herm100). It was received from an Ebay deal with WM5. I flashed it with the ATT OEM WM6pro (aka shipped wm6). Once it hit the three color boot screen, it sat on that for a couple of minutes then started cooking. Once it showed a progress bar, it took about 3 minutes to cook the WM6 over the WM5. It also showed a popup that stated going back to WM5 was not an option.
I would suggest running the installer again and going down to 7-11 for a refreshment. You may not have let it percolate long enough to set itself up for the actual ROM overwriting.
gorkalraghavendra said:
Hello Everybody,
My mobile at&t 8525 alias HTC 8525 is stuck in windows operator logo.It would not boot further. It happened while I tried to upgrade it from Windows 5.0 to Windows 6.0.First I got a tri-colour screen,but in a hurry I tried to backgrade to windows 5.0 again.
Other problem the mobile cannot be synced. I have installed Microsoft Active sync 4.5. Even then it could not be synced.
I tried to read all the posts ,but could not understand anything.
So please help me in getting my mobile repaired
Click to expand...
Click to collapse