Related
I was trying to upgrade to radio v1.43 in the hope that battery life was improved over 1.41 however when it got to 8% it stopped and gave me an error i can't remember After atempting to recover, it got off the three colour screen now the 3100 stalls on the blackshadow version4 screen (bootloader screen?) and goes no further. I tried reflashing but got a 260 and using mtty, only getting 2 com port options, didn't offer any help.
I'm really sorry to have not been able to sort this with reading through the relevant post but I haven't found a solution. What else can I try?
Hi,
Could you pls advise what is your device made, model, SPL version ... etc.
Also did you try to do Hard reset?
I'm using now black MAJIK (and few days ago black shadow) with radio 1.43 with no problem.
its the SPV m3100 When I decided to go Black shadow I read up on mr vanx and made sure I had all the things I needed. If I remember right, when I came to upgrade to Majik the auto detect found the second option down
SPL-1.04/1.10 - 1.09 Bootloader. I've realized since I had a spaz and ran the RUU from the archive this time. From what I've since read thats not too cleaver.
I have tried a hard reset and took the battery out instead of pressing space.
I dont know if this information on the starter screen is of use
M 05
S 04
B 05 D 3lak
I'm not sure, but hard reset doesnt mean you take the batery out.
Please check that link:
http://wiki.xda-developers.com/index.php?pagename=Hermes_For_Beginners#hardreset
I was in your position (hanged on booting) few days ago, and when i did hard reset, it changes every thing to basic normal condition.
i meant when i did a hard reset when it asked me to press space to reboot I took the battery out. I tried again this time pressing space to reboot but I still get stuck on the loading screen. I can't connect by USB to the PC I'm guessing the drivers on the phone haven't loaded and I'm stuck as to what to do.
Does anyone have any ideas?
try look at it http://forum.xda-developers.com/showthread.php?t=286755
ok I've tried everything I can think of to connect the 3100 to the computer so I can reflash it but mtty gives only com 1 and com2 but no USB and neither those two work, active sync wont connect so I disabled it as suggested and running the radio ruu and wrapper wont querry the device. I am now at a loss as to what to do next someone must know what I should do. Please?
what is your SPL?
try this http://wiki.xda-developers.com/index.php?pagename=HTC_Hermes
sl is 1.09 i'd updated it on the previously successful black shadow flash
msn [email protected]
icq 150277111
AIM TazmanFH9
Yahoo bigfathairyboggart
I have tried changing KITL trasport but I am unable to select or chose either option. I have also tried the rversion command in the tri colour screen but nothing happens. I hope I'm missing something nice and simple but I get the feeling I'm not going to be that lucky. Please help
tcSPVm3100 said:
sl is 1.09 i'd updated it on the previously successful black shadow flash
Click to expand...
Click to collapse
I suggest you check again, press and hold the side OK button and the power button...then put the stylus into the hole in the bottom of the unit.
yeah I've done that it's "SPL-1.09"
I had this exact problem yesterday, with the same bootloader too. The phone would not pass the splash and IT refused to upgrade. I ended up downgrading to a shipped wm5 rom (in my case the cingular 1.30.502.1_1.11.00.00) which to my surprise actually worked as no rom radio or spl upgrade moved at al on my phone. Then upgraded back to black majik. I hope this helps.
Thanks. I downloaded the trial of wm5 from the windows website and it asked me to install .NET framework version 1 so I got that but it turns out to be 2.0 not 1.1 It would say it had repaired but it would say this with or without the phone connected.
tcSPVm3100 said:
Thanks. I downloaded the trial of wm5 from the windows website and it asked me to install .NET framework version 1 so I got that but it turns out to be 2.0 not 1.1 It would say it had repaired but it would say this with or without the phone connected.
Click to expand...
Click to collapse
Just download a WM5 ROM from the wiki page!
ok tried this too no luck.
Trying to use the one from orange (linked to through wikki) I get an 294 invalid vendor error however active sync cannot connect yet of course so is this to be expected?
I have however gotten a connection with mtty which is a step forward dunno what to do with it yet though except trying the password 0000000000000000 command but it not disabling the password. This then lead me to read for a further hour how to change it and I've got to be honest; it beat me. I have No idea what the hell its talking about. My head hurt with so much reading.
I get a no gsm pop up v briefly on loader. I so want my phone back
I have since tried CID unlocker just so i get something installed onto this brick but I either get a connection error or it telling me it can't install for some other reason. I can not set the password in mtty to 0000000000000000 so how do I do that and is this the first step to getting things sorted? "just running a rom install" is not happening I can get a USB connection in mtty and that is it. Is the fact i'm running SPL 1.09 a problem? I'm getting precious little help guys If i'm posting in the wrong place or something please let me know. I need thing thing back now. Hours are drifting by with me trying to get some head knowledge but I still need some guidance please
tcSPVm3100 said:
I have since tried CID unlocker just so i get something installed onto this brick but I either get a connection error or it telling me it can't install for some other reason. I can not set the password in mtty to 0000000000000000 so how do I do that and is this the first step to getting things sorted? "just running a rom install" is not happening I can get a USB connection in mtty and that is it. Is the fact i'm running SPL 1.09 a problem? I'm getting precious little help guys If i'm posting in the wrong place or something please let me know. I need thing thing back now. Hours are drifting by with me trying to get some head knowledge but I still need some guidance please
Click to expand...
Click to collapse
can u flashing HARD V7?,i think better u have IPL 1.04 SPL 2.10olipro first ,then try to flashing radio?
and did u try SD card.
In bootloader can anyone here connect with active sync? I can't so updating rom and radio flashes in the usual way isn't possible. Trying the hard spl again it tells me to make sure active sync is connected and as it isn't it throws back a 262 update error. 0% on the hermes and that's currently as far as I can get. I have no means with which to access the memory card.
The reason you get an invalid vendor ID is because your CID doesnt match....download a ROM which is for your device (an orange one?)...then try.
You need to read the wiki alot more before trying anything else since you are not aware of the vendor ID error...nor the fact you MUST use HardSPL.
I linked to the orange ROM from wikki and tried installing it. it was while installing THIS ROM SPV_M3100_ROMUpdate_0407.exe I got invalid vendor error.
Installing a recent DL on HARD spl v7 I get a 240 open file error that's one I haven't had before.
With all other attempts they all say they want an active sync connection.
I can not connect to the phone through active sync
so all attempts by me to flash anything to the phone using an RUU fails.
Ok...I have been through all the posts about upgrading etc. I still have a problem and I'm sure that I'm overlooking something....but I can't figure it out on my own. Here is what is happening (it does the same thing with every RUU that I've used...the DST fix...upgrading to WM6....etc)
1. I run the RUU and let it go through its routine (extract files, verify info on pc, etc.)
2. I check the box that says I have read the readme and click next
3. The next screen appears and it has the following steps:
Connect to the USB cable (check)
Establish an ActiveSync Connection (check)
Disable standby and hibernation on PC (check)
Make sure batter is > 50% (check)
Then I check the box and click next
4. I pick the update and click on the update button
5. I verify that I want to upgrade my phone from ROM verion x.xx.xxx to x.xx.xxx and click next
6. The program tells me that I am finally ready to update...and if I am sure I want to proceed to click next...so I click next
7. As soon as I click next...the progress bar comes up on my pc and my phone goes into standby mode (no bootloader...just standby). The progress bar never moves.
8. After a minute or two the RUU give me the ERROR [260]: Connection
9. I reboot my device and repeat steps 1-8
10. I reboot my device and my computer and repeat steps 1 - 8.
Now if I leave my device connected to the usb and close out the RUU after it gives me the ERROR [260], and then run the RUU again...when it is first verifying the information on my pc (before it asks any questions and before it tells me to connect my device) it will throw the device into bootloader mode. If I try to keep running the RUU while the device is in bootloader mode it give me the error that my device is not connected. I have tried and tried...maybe one of ya'll can help me. Thanks in advance
Chris
Some questions:
.) Is your desktop PC running XP or Vista?
If you have a firewall running, close it.
.) If you running Vista check this guide:
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=23&Itemid=27
.) What updates did you try to flash?
.) Did you install Olipros bootloader first?
gerald_s said:
Some questions:
.) Is your desktop PC running XP or Vista?
If you have a firewall running, close it.
.) If you running Vista check this guide:
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=23&Itemid=27
.) What updates did you try to flash?
.) Did you install Olipros bootloader first?
Click to expand...
Click to collapse
XP
No firewall
I tried to flash the WM6 from AT&T I assume its beta
and no did not install the Olipros bootloader
Ok...I think I found out how to do this...Ya'll can tell me if I'm screwing something up.
I go through all the steps listed above until it gets to the progress screen. When it gets there I manually put the the device in bootloader mode (Power, side ok, and reset). Once I do this...the progress bar starts moving. I will let you know if this works...
Hmmmm
Its not the way it should work but if it works its ok
You should have installed Olipros HardSPL first and then try to flash an official rom. If its working then something with your download is wrong.
What ROM is on there now?
Has the phone been CID unlocked?
Oli's CustomRUU is better, you may want to unpack the ROM and put the NBH in a folder with Oli's RUU and then do the upgrade.
BTW, gerald_s is right, you should not have to do that... what you may want to do is put the phone in Bootloader mode manually (while not connected to the PC), then plug in the USB, then start the RUU. That helps some people with 260 error.
I've got the same damn issue... it's driving me crazy. I had this occur when I flashed my Hermes100 from the stock version to Custel's. After about 15 starts and reboots it took. I'm now trying to get to Vp3G's 3.60 and it continues to give me the 260 error.
I am trying to figure out how to fomat my micro, but really hoping to find a solution over cable.
Hermes 100
IPL 1.04
SPL - 2.10 Olipro
Any suggestions?
You may be trying to flash a rom that includes the radio rom. What is your device? Is it possible that your device is a new x01ht with radio 1.14 and radio bootloader 0182? If yes, then you will get this error when you try to flash a rom with this method because during the flash it will be disconnected by the radio bootloader because it is not overwriteable. If you flash using the NBH file on the microSD, it will skip past radio and radio boot and just flash the other parts of the file.
mikebraeuer said:
I've got the same damn issue... it's driving me crazy. I had this occur when I flashed my Hermes100 from the stock version to Custel's. After about 15 starts and reboots it took. I'm now trying to get to Vp3G's 3.60 and it continues to give me the 260 error.
I am trying to figure out how to fomat my micro, but really hoping to find a solution over cable.
Hermes 100
IPL 1.04
SPL - 2.10 Olipro
Any suggestions?
Click to expand...
Click to collapse
If you are running windows XP, just connect the card to the computer, open MY COMPUTER, right-click the removable disk that is your microSD and then click format. Default in windows xp is to format using FAT32 filesystem which is perfect.
The thing is... if you dont know how to format a drive in Windows, should you be flashing your device yourself?
Which Solution???
I've got a Softbank X01HT with:
S/N: HT639
SuperCID <--- result of checking by mtty
IPL: 1.04
SPL: 2.10Olipro
GSM: 1.47.00.10
OS: 3.54.07 WWE
I tried to flash with new Schap 3.54c but the process would not be done coz ERROR 262 or ERROR 302. Fortunately, after failure of flashing, my device is still normal running. Then I tried to flash radio 1.51.00.10 but I got the same above. Once again, I have just tried to flash splash screen and I got the same result too. It mean my device can not upgrade anything !
Anybody here show me a solution that help my device to become a normal device, I mean it will be able to flash anything ROM as it would be! Don't tell me READ and READ, I had read so much . And don't tell me use MTTY again SPL1.01MFG, I think that is a final solution
Wantoknow said:
I've got a Softbank X01HT with:
S/N: HT639
SuperCID <--- result of checking by mtty
IPL: 1.04
SPL: 2.10Olipro
GSM: 1.47.00.10
OS: 3.54.07 WWE
I tried to flash with new Schap 3.54c but the process would not be done coz ERROR 262 or ERROR 302. Fortunately, after failure of flashing, my device is still normal running. Then I tried to flash radio 1.51.00.10 but I got the same above. Once again, I have just tried to flash splash screen and I got the same result too. It mean my device can not upgrade anything !
Anybody here show me a solution that help my device to become a normal device, I mean it will be able to flash anything ROM as it would be! Don't tell me READ and READ, I had read so much . And don't tell me use MTTY again SPL1.01MFG, I think that is a final solution
Click to expand...
Click to collapse
Have you tried flashing with your microSD?
Kevbodian said:
Have you tried flashing with your microSD?
Click to expand...
Click to collapse
I forgot to tell that, I had flashed through extra memory card yet, and could be done!
But I wanna flash ROM against CustomRUU through MS Active Sync as I had used before. Can you help me
i have a problem very similar to Chris. when i check the box "yes activesync is syncronised", and then the progressbar shows up and the phone goes into standby.
i've turned standby of in powermanagement options.
my os is XP
i use active sync v4.5
and this is first time i try this.
i've read something about this bootloader, i can get there but then i cannot sync with active sync. so i kinda stuck.
have been searching the forums and this was the same problem as mine but i don't understand your solutions.
//KufrA
--Problem solved--
i did all things without activesync,
1. start phone in bootloader
2. do the install
3. wait 0% to 100%, and done.
is there a problem with active sync or why do i have to do anything with it at all?
Hi All,
I'm new to the PDA-world and the Hermes. I'm trying to Hard SPL my Hermes, but it fails everytime.
When I run 2.10 - Hard-SPL-V7, it kills activesync and my connection is lost and I get always the message "error 260, Update error".
I have the latest framework edition and tried it on 3 pc's (1 Vista, 2 XP)...
What am I doing wrong?
Hope somebody can help me....
Kind Regards,
Micha
1). dont connect to active sync. open active sync and untick "allow usb connections".
2). put hermes into bootloader and connect to usb.
3). run ruu_wrapper.exe
should update to hard spl....
dont forget to tick "allow usb connections" again or you wnot be able to sync..
error 260 is an open port error.
if you wish to flash new os would advise to use sd card method. its safer than using the computer. just make sure you have greater than 50% battery power. happy flashing
Thnx, will give it a try.
First I have to flash HardSPL before I can flash a new OS, don't I?
yep, sorry, should have said run the ruu_wrapper for hard spl. My bad...
im having the same problem. I also tried the way ultramag recommended but i also received the same ending. After time i try i get the Error 260 Update error. Im running SPL 2.04 and the HTC WM6 rom from the HTC website. Does any one know what the problem is?
ultramag69 said:
2). put hermes into bootloader and connect to usb.
Click to expand...
Click to collapse
NOOOOO, that won't work, you need the SSPL to deploy to the phone, if you're running stock HTC bootloader this won't work at all, otherwise we'd have no need for Hard-SPL
hey olipro, then how would i fix this. Im running the stock rom from the HTC website with no hacks. Im trying to load PDA Corners V9 rom. Any ideas on how to fix? thanks!
Take a peek at the guide i wrote about updating the hardspl. Theres some explanation about why we need to use SSPL and the procedures.
http://www.mrvanx.org/hermes_guide/hardspl
thats the guide i used. it still gives me the error. I even unchecked "allow connections" cause i read somewhere that that would help.
i did this two days ago on my phone, im running windows vista on my home laptop and got any number of errors and problems trying to do it via sync with the phone (even after reading the vista troubleshooter, with the drivers etc)
What i ended up using was the memory card upgrade, dump the file onto the memory card and go into bootloader with the card installed.
worked fine doing that way, maybe less risky as there is no chance of the usb cable coming out.
just make sure you have a good battery charge on the phone.
Help Help Help w bricked 8525
I got into this position trying to upgrade WM5 to WM6 from HTC site.
Process got to 20% and just stayed there.
I reconnected usb cable and got a vendor id error
Then I get the Error [260]: CONNECTION
I have read a lot of posts and have tried the sd method (although i am not 100% clear) and all i get is the screen with four colors, red, green blue and white.
I believe this is the bootloader? I have downloaded RUU_signed.nbh, renamed it to hermimg.nbh, installed on root of my SD card and held OK, soft reset and power button:
My display reads:
HERM100
IPL-1.04
HERM100
SPL-2.03
This is where my journey ends.
All post indicate that the device can be reflashed and have the OS reinstalled. I can't get there from here.
Can anyone please help?
blackdog9692 said:
I have read a lot of posts and have tried the sd method (although i am not 100% clear) and all i get is the screen with four colors, red, green blue and white.
Click to expand...
Click to collapse
How big is your SD card? Flashing only works with cards <2GB. Also, sometimes certain cards just don't work for flashing, and just swapping to a different card fixes the problem.
I assume you searched the wiki, and found the relevant pages on the Hermes (including SD Card Flashing and other things about flashing/upgrading) there?
Still Lost
My SD is 2GB and I have tried many times but i just keep getting the 4 color screen. rt now when i boot from the SD my screen goes white and displays "Loading..." and then returns to bootloader screen. When i attempt to flash the rom via PC to WM5 or WM6 i get the Error 260, i also get a vendor ID error sometimes.
How can i find the key 8525 thread that i am told has the answer to my delima? I keep picking up bits and pieces but am missing some key steps and tips.
blackdog9692 said:
My SD is 2GB and I have tried many times but i just keep getting the 4 color screen. rt now when i boot from the SD my screen goes white and displays "Loading..." and then returns to bootloader screen.
Click to expand...
Click to collapse
That sounds like the SD card is formatted incorrectly. Make sure it's formatted using fat32, nothing else will work.
Still not there from here
Thanks for your help. Before I formatted the SD FAT32, nothing would happen doing the bootloader reset. OK/ON/reset button.
After format and only the hermimg.nbh file renamed as indicated, I then get what looks like the loading process but back to the bootloader screen.
Q1: This is an AT&T 8525, it was perfectly fine before failure from WM5 to WM6 (process froze at 20%), what is the RUU file that I need to put on SD??
Q2: After "Loading ..." I try the WM5 PC upgrade of ROM via USB cable, I get the load process to appear to work but it gets to 1% and the phone reboots and the PC reports error [294]: Invalid vendor ID. If I do this again I will get the Error [260]. Ive repeated the process several times.
Is this the normal course to take or should the "SD Method" (with the WM5 or WM6 RUU.. file) complete the process to a working OS?
Q3: Is my situation hopeless? ATT will take my out of warrantee 8525 and reflash for $129. Reading the threads it seems that like me this can be done by me, this is my desire.
Q4: I still am confused by some basic terms and assumed steps. I dont understand "Hard SPL" or OLI's IPLs/SPLs and when and when to use them.
The newbe guide has been off line. I will look again. Is there a single place to read about "radio PDAs and the 8525 and understand the software build and custom options?
Sy for the long post. But still want to fix if possible or I will be force to mail in for ATT repair.
Thank you all.
blackdog9692 said:
Q4: I still am confused by some basic terms and assumed steps. I dont understand "Hard SPL" or OLI's IPLs/SPLs and when and when to use them.
Click to expand...
Click to collapse
Oh boy, you haven't installed HardSPL? You are walking a bit of a line there mate...
HardSPL is a custom boot loader that makes bricking your phone when flashing much harder to do, and helps large amounts in the recovery process if you phone does brick.
Does the phone boot at this point? If so, do not try flashing the phone again. Go get a copy of HardSPL and install it, then try flashing from the SD.
I still wonder why people didn't read before bricking...
Anyway, you should start reading now and wiki is your friend. Your SPL is 2.03, so look at the bottom of the page (there is only one solution till now, so good luck with that):
Code:
1. Boot OS using KITL+PB
2. Do no disconnect your HERMES till the end of the step 6
3. Download SSPL on HERMES by wifi from ie explorer
4. Launch SSPL then flash Hard-SPL from your computer
5. Put your hermes in bootloader mode
6. Flash any radio in NBH format from your computer
Still researching and working this bricked 8525
Thanks for coming to my aide. I believe that I have Hard SPL'd my device. I downloaded Olipro's Hard SPL v7. extracted the RUU_ file and renamed to hermimg.nbh.
I then put it on an SD card and held the keys and reset. The device displayed a white screen and "Loading..." appeared. Afterward the 8525 returned to the stipped boat loader screen and that is where I am now.
Some of the help i receive and read on wiki threads has me confused with what to do next and how "exactly" to do it.
It does seem that I am not alone and people have fixed their phones and the process to do this is on the forum. I'm just still missing something.
Help me further if u can.
Thank you.
blackdog9692 said:
Thanks for coming to my aide. I believe that I have Hard SPL'd my device. I downloaded Olipro's Hard SPL v7. extracted the RUU_ file and renamed to hermimg.nbh.
Click to expand...
Click to collapse
FYI: bad form to PM someone and post the same thing here. Keep it in the thread so others can be helped as well.
As I replied in the PM, if I'm understanding your post correctly, the phone boots to the tri-colour screen?
What text is showing on the screen? This will tell if HardSPL is on the phone or not.
jdc said:
What text is showing on the screen? This will tell if HardSPL is on the phone or not.
Click to expand...
Click to collapse
We already know that the phone is without HardSPL, according:
My display reads:
HERM100
IPL-1.04
HERM100
SPL-2.03
This is where my journey ends.
Click to expand...
Click to collapse
There is small chance (read my previous post) to unbrick device with SPL2.03 so better try to get this back from where you take it.
And please, change topic, because this brick isn't HardSPL fault at all.
Edit: oh dear, it's even not your topic ...good game, I'm off
Hello Everybody,
My mobile at&t 8525 alias HTC 8525 is stuck in windows operator logo.It would not boot further. It happened while I tried to upgrade it from Windows 5.0 to Windows 6.0.First I got a tri-colour screen,but in a hurry I tried to backgrade to windows 5.0 again.
Other problem the mobile cannot be synced. I have installed Microsoft Active sync 4.5. Even then it could not be synced.
I tried to read all the posts ,but could not understand anything.
So please help me in getting my mobile repaired
Don't worie.
I had somewhat the same issue with a bad ROM flash.
Just disconnect the USB and boot to the bootloader screen (the tricolour screen) and you should be able to reflash the phone again.
Problem in syncing the mobile
I am not able to sync the mobile to the laptop.I have installed Microsoft Active sync 4.5. Even then it is not syncing.So how could I run the hermes upgrade if the mobile is not helping.
Please help
In Activesync on PC - Untick "Allow USB Connections".
Put the Hermes into bootloader (tri-colour screen) and connect by usb. Run the RUU_Wrapper.exe file you want. Follow onscreen instructions.
You need to have installed Hard SPL V7 for this to work...
did not work
Hello Boss
I tried to follow the procedure you suggested me. but it did not work. I tried with Hard SPl 7.0.
Please give me some suggestion
you dont need an active sync connection to flash it. Enter bootloader(tri colour screen) as you were told in the previous posts and Just click on the boxes that you do have a connection(even though you dont) and then flash the rom.
@ultramag69 i hve never had to untick allow usb connections and i have cocked up loads of rom flashes, saying that i have never had a problem flashing in vista either so maybe i am lucky
If you still cant flash doing it this way, then maybe you should try flashing from sd card instead, just make sure the battery is fully charged. Full instructions of how to do this are found in the hermes wiki, which i advise you to read anyway.
Oh and good luck anyway, you should be able to recover the phone from this ,so i wouldnt fret too much
Guess he isnt hardspl'ed... then his batt is death... must to flash a shipped rom.
correct me if im wrong.
Problem with upgrade At&T 8525 mobile
Hi!
I'm having problems with my Cingular 8525, after I made the upgrade to WM6.1 (FARIA-R32-XDA2_WM6.1.rar) for WM 6.5 (FCWs_stock_like_6.5_v3.rar), and slowed my device does not work anymore. He died.
I need help please. How resurrect it?
Excuse my English.
english is not the problem here cause we need more info... device info SPL IPL hardSPL? you go from 6.5 to 6.1?
Do you try to flash first the Stripped?
Does your batt has charge enough to boot?
There are many many things to say so... start to tell us all your history!
Hi
I tried to Hard spl with Hard Splv7. But I got a error. I even tried the Sd Card method.Its says loading and I get the tricolour mode. If I press the Power button its not showing the status of upgradation.
Where can I get a shipped rom. Actually my Spl is 1.11.
Hi
I tried to Hard spl with Hard Splv7. But I got a error. I even tried the Sd Card method.Its says loading and I get the tricolour mode. If I press the Power button its not showing the status of upgradation.
Where can I get a shipped rom. Actually my Spl is 1.11.
check the wiki pages for your device in the upper bar of this web forums
there are many official roms.
I also am currently using an 8525 (Herm100). It was received from an Ebay deal with WM5. I flashed it with the ATT OEM WM6pro (aka shipped wm6). Once it hit the three color boot screen, it sat on that for a couple of minutes then started cooking. Once it showed a progress bar, it took about 3 minutes to cook the WM6 over the WM5. It also showed a popup that stated going back to WM5 was not an option.
I would suggest running the installer again and going down to 7-11 for a refreshment. You may not have let it percolate long enough to set itself up for the actual ROM overwriting.
gorkalraghavendra said:
Hello Everybody,
My mobile at&t 8525 alias HTC 8525 is stuck in windows operator logo.It would not boot further. It happened while I tried to upgrade it from Windows 5.0 to Windows 6.0.First I got a tri-colour screen,but in a hurry I tried to backgrade to windows 5.0 again.
Other problem the mobile cannot be synced. I have installed Microsoft Active sync 4.5. Even then it could not be synced.
I tried to read all the posts ,but could not understand anything.
So please help me in getting my mobile repaired
Click to expand...
Click to collapse
I want to help someone on this please , bcs HTC SPV M3100 when i'm trying to switch on phone was stuck on HTC logo and nothing more , i have try to put on boatloader mode and phone was going on bootloader mode three color screen and show this:
HERM100
IPL-1.04
HERM100
SPL-2.03
i'm trying with hard spl from Pof soft but error getting.
Can someone find a time to help me?
hallooo
experts please!
Hello haveri,
what ROM are you trying to start? I was stuck on HTC logo too, when I tried to start a ROM without installing Striped ROM first, which was highly needed. So I done hard reset(three color screen), and flashed again.
For starters, put in bootloader, connect to PC (1st untick "Allow USB Connections" in activesync) and run Hard SPL V7. Install it on your Herms and hope it works because otherwise you are in for a whole heap of hairpulling frustration...
If you get Hard SPL onto your Hermes then use the sd card method to flash a new rom...
You could have avoided this by doing a little research instead of going full pelt into flashing, you Hard SPL BEFORE you get into trouble, NOT AFTER....
Hi guys,
I have a similar problem with a T-Mobile branded TyTn from a friend of mine who thought flashing ROMs without putting device into HardSPL would be clever.
The devices has also IPL-1.04 and SPL-2.03 and from the bootscreen it looks like WM5 should have been installed. I also get the "NO GSM" message and I REALLY tried every fking method but without success.
I even created a Goldcard (and verified on another device it's working, level 0 instead FF) and tried to flash several ROMs (also Cingular WM5 ROM and original german T-Mobile ROM) but no luck.
I also tried to run HardSPL V7 but as far as I remember it just said it cannot connect.
Funny thing: HardSPL V9 DOES start flashing and on the PDA and the PC the bar shows 100% but some moments later it says "Could not update" (or something like that).
I even tried different mtty methods from several posts from the forum (erasing the NAND on different ways, qtek loader method with erasing the first blocks) but I'm really really frustrated now and I believe there is no solution here?! (device has no guarentee)
So, if someone has ANY hint or useful information write it down or send me a PM.
I gladly appreciate your help and hope for a solution!
Cheers
P.S.: I couldn't find any information saying Goldcard method works (or even exists) for Hermes. Can someone confirm it does really work?