Hello Everybody,
My mobile at&t 8525 alias HTC 8525 is stuck in windows operator logo.It would not boot further. It happened while I tried to upgrade it from Windows 5.0 to Windows 6.0.First I got a tri-colour screen,but in a hurry I tried to backgrade to windows 5.0 again.
Other problem the mobile cannot be synced. I have installed Microsoft Active sync 4.5. Even then it could not be synced.
I tried to read all the posts ,but could not understand anything.
So please help me in getting my mobile repaired
Don't worie.
I had somewhat the same issue with a bad ROM flash.
Just disconnect the USB and boot to the bootloader screen (the tricolour screen) and you should be able to reflash the phone again.
Problem in syncing the mobile
I am not able to sync the mobile to the laptop.I have installed Microsoft Active sync 4.5. Even then it is not syncing.So how could I run the hermes upgrade if the mobile is not helping.
Please help
In Activesync on PC - Untick "Allow USB Connections".
Put the Hermes into bootloader (tri-colour screen) and connect by usb. Run the RUU_Wrapper.exe file you want. Follow onscreen instructions.
You need to have installed Hard SPL V7 for this to work...
did not work
Hello Boss
I tried to follow the procedure you suggested me. but it did not work. I tried with Hard SPl 7.0.
Please give me some suggestion
you dont need an active sync connection to flash it. Enter bootloader(tri colour screen) as you were told in the previous posts and Just click on the boxes that you do have a connection(even though you dont) and then flash the rom.
@ultramag69 i hve never had to untick allow usb connections and i have cocked up loads of rom flashes, saying that i have never had a problem flashing in vista either so maybe i am lucky
If you still cant flash doing it this way, then maybe you should try flashing from sd card instead, just make sure the battery is fully charged. Full instructions of how to do this are found in the hermes wiki, which i advise you to read anyway.
Oh and good luck anyway, you should be able to recover the phone from this ,so i wouldnt fret too much
Guess he isnt hardspl'ed... then his batt is death... must to flash a shipped rom.
correct me if im wrong.
Problem with upgrade At&T 8525 mobile
Hi!
I'm having problems with my Cingular 8525, after I made the upgrade to WM6.1 (FARIA-R32-XDA2_WM6.1.rar) for WM 6.5 (FCWs_stock_like_6.5_v3.rar), and slowed my device does not work anymore. He died.
I need help please. How resurrect it?
Excuse my English.
english is not the problem here cause we need more info... device info SPL IPL hardSPL? you go from 6.5 to 6.1?
Do you try to flash first the Stripped?
Does your batt has charge enough to boot?
There are many many things to say so... start to tell us all your history!
Hi
I tried to Hard spl with Hard Splv7. But I got a error. I even tried the Sd Card method.Its says loading and I get the tricolour mode. If I press the Power button its not showing the status of upgradation.
Where can I get a shipped rom. Actually my Spl is 1.11.
Hi
I tried to Hard spl with Hard Splv7. But I got a error. I even tried the Sd Card method.Its says loading and I get the tricolour mode. If I press the Power button its not showing the status of upgradation.
Where can I get a shipped rom. Actually my Spl is 1.11.
check the wiki pages for your device in the upper bar of this web forums
there are many official roms.
I also am currently using an 8525 (Herm100). It was received from an Ebay deal with WM5. I flashed it with the ATT OEM WM6pro (aka shipped wm6). Once it hit the three color boot screen, it sat on that for a couple of minutes then started cooking. Once it showed a progress bar, it took about 3 minutes to cook the WM6 over the WM5. It also showed a popup that stated going back to WM5 was not an option.
I would suggest running the installer again and going down to 7-11 for a refreshment. You may not have let it percolate long enough to set itself up for the actual ROM overwriting.
gorkalraghavendra said:
Hello Everybody,
My mobile at&t 8525 alias HTC 8525 is stuck in windows operator logo.It would not boot further. It happened while I tried to upgrade it from Windows 5.0 to Windows 6.0.First I got a tri-colour screen,but in a hurry I tried to backgrade to windows 5.0 again.
Other problem the mobile cannot be synced. I have installed Microsoft Active sync 4.5. Even then it could not be synced.
I tried to read all the posts ,but could not understand anything.
So please help me in getting my mobile repaired
Click to expand...
Click to collapse
Related
I was trying to upgrade to radio v1.43 in the hope that battery life was improved over 1.41 however when it got to 8% it stopped and gave me an error i can't remember After atempting to recover, it got off the three colour screen now the 3100 stalls on the blackshadow version4 screen (bootloader screen?) and goes no further. I tried reflashing but got a 260 and using mtty, only getting 2 com port options, didn't offer any help.
I'm really sorry to have not been able to sort this with reading through the relevant post but I haven't found a solution. What else can I try?
Hi,
Could you pls advise what is your device made, model, SPL version ... etc.
Also did you try to do Hard reset?
I'm using now black MAJIK (and few days ago black shadow) with radio 1.43 with no problem.
its the SPV m3100 When I decided to go Black shadow I read up on mr vanx and made sure I had all the things I needed. If I remember right, when I came to upgrade to Majik the auto detect found the second option down
SPL-1.04/1.10 - 1.09 Bootloader. I've realized since I had a spaz and ran the RUU from the archive this time. From what I've since read thats not too cleaver.
I have tried a hard reset and took the battery out instead of pressing space.
I dont know if this information on the starter screen is of use
M 05
S 04
B 05 D 3lak
I'm not sure, but hard reset doesnt mean you take the batery out.
Please check that link:
http://wiki.xda-developers.com/index.php?pagename=Hermes_For_Beginners#hardreset
I was in your position (hanged on booting) few days ago, and when i did hard reset, it changes every thing to basic normal condition.
i meant when i did a hard reset when it asked me to press space to reboot I took the battery out. I tried again this time pressing space to reboot but I still get stuck on the loading screen. I can't connect by USB to the PC I'm guessing the drivers on the phone haven't loaded and I'm stuck as to what to do.
Does anyone have any ideas?
try look at it http://forum.xda-developers.com/showthread.php?t=286755
ok I've tried everything I can think of to connect the 3100 to the computer so I can reflash it but mtty gives only com 1 and com2 but no USB and neither those two work, active sync wont connect so I disabled it as suggested and running the radio ruu and wrapper wont querry the device. I am now at a loss as to what to do next someone must know what I should do. Please?
what is your SPL?
try this http://wiki.xda-developers.com/index.php?pagename=HTC_Hermes
sl is 1.09 i'd updated it on the previously successful black shadow flash
msn [email protected]
icq 150277111
AIM TazmanFH9
Yahoo bigfathairyboggart
I have tried changing KITL trasport but I am unable to select or chose either option. I have also tried the rversion command in the tri colour screen but nothing happens. I hope I'm missing something nice and simple but I get the feeling I'm not going to be that lucky. Please help
tcSPVm3100 said:
sl is 1.09 i'd updated it on the previously successful black shadow flash
Click to expand...
Click to collapse
I suggest you check again, press and hold the side OK button and the power button...then put the stylus into the hole in the bottom of the unit.
yeah I've done that it's "SPL-1.09"
I had this exact problem yesterday, with the same bootloader too. The phone would not pass the splash and IT refused to upgrade. I ended up downgrading to a shipped wm5 rom (in my case the cingular 1.30.502.1_1.11.00.00) which to my surprise actually worked as no rom radio or spl upgrade moved at al on my phone. Then upgraded back to black majik. I hope this helps.
Thanks. I downloaded the trial of wm5 from the windows website and it asked me to install .NET framework version 1 so I got that but it turns out to be 2.0 not 1.1 It would say it had repaired but it would say this with or without the phone connected.
tcSPVm3100 said:
Thanks. I downloaded the trial of wm5 from the windows website and it asked me to install .NET framework version 1 so I got that but it turns out to be 2.0 not 1.1 It would say it had repaired but it would say this with or without the phone connected.
Click to expand...
Click to collapse
Just download a WM5 ROM from the wiki page!
ok tried this too no luck.
Trying to use the one from orange (linked to through wikki) I get an 294 invalid vendor error however active sync cannot connect yet of course so is this to be expected?
I have however gotten a connection with mtty which is a step forward dunno what to do with it yet though except trying the password 0000000000000000 command but it not disabling the password. This then lead me to read for a further hour how to change it and I've got to be honest; it beat me. I have No idea what the hell its talking about. My head hurt with so much reading.
I get a no gsm pop up v briefly on loader. I so want my phone back
I have since tried CID unlocker just so i get something installed onto this brick but I either get a connection error or it telling me it can't install for some other reason. I can not set the password in mtty to 0000000000000000 so how do I do that and is this the first step to getting things sorted? "just running a rom install" is not happening I can get a USB connection in mtty and that is it. Is the fact i'm running SPL 1.09 a problem? I'm getting precious little help guys If i'm posting in the wrong place or something please let me know. I need thing thing back now. Hours are drifting by with me trying to get some head knowledge but I still need some guidance please
tcSPVm3100 said:
I have since tried CID unlocker just so i get something installed onto this brick but I either get a connection error or it telling me it can't install for some other reason. I can not set the password in mtty to 0000000000000000 so how do I do that and is this the first step to getting things sorted? "just running a rom install" is not happening I can get a USB connection in mtty and that is it. Is the fact i'm running SPL 1.09 a problem? I'm getting precious little help guys If i'm posting in the wrong place or something please let me know. I need thing thing back now. Hours are drifting by with me trying to get some head knowledge but I still need some guidance please
Click to expand...
Click to collapse
can u flashing HARD V7?,i think better u have IPL 1.04 SPL 2.10olipro first ,then try to flashing radio?
and did u try SD card.
In bootloader can anyone here connect with active sync? I can't so updating rom and radio flashes in the usual way isn't possible. Trying the hard spl again it tells me to make sure active sync is connected and as it isn't it throws back a 262 update error. 0% on the hermes and that's currently as far as I can get. I have no means with which to access the memory card.
The reason you get an invalid vendor ID is because your CID doesnt match....download a ROM which is for your device (an orange one?)...then try.
You need to read the wiki alot more before trying anything else since you are not aware of the vendor ID error...nor the fact you MUST use HardSPL.
I linked to the orange ROM from wikki and tried installing it. it was while installing THIS ROM SPV_M3100_ROMUpdate_0407.exe I got invalid vendor error.
Installing a recent DL on HARD spl v7 I get a 240 open file error that's one I haven't had before.
With all other attempts they all say they want an active sync connection.
I can not connect to the phone through active sync
so all attempts by me to flash anything to the phone using an RUU fails.
I'm following Mr Vanx's guide for upgrading my Jasjam from WM5 to WM6, but am having trouble with flashing the new bootloader onto the device. It's a second-hand telstra imate. I just bought it off ebay a couple of weeks ago and need to upgrade it to get it to read sdhc memory cards. I can't get it to connect to optus' (my mobile contract provider) mobile internet either, which I did via GPRS on my old phone. I'm hoping by upgrading the OS I can remove all of Telstra's code so It's not trying to connect to telstra's 3g network when I start the web browser.
When I get to the last step of the Hard-SPL installation, where the "updater will flash the new SPL and then restart your device (this will take generally less than a minute)" , the phone restarts almost immediately after clicking yes when prompted on the phone. The screen quickly goes to the bootloader screen, which says
"herm 100
IPL-SSPL by Des
Herm 100
SPL-1.09.ds"
The PC says that it can't connect to the phone and I should check the cable, which is still connected
The phone stays on the bootloader screen until I hit the soft reset, and WM5 boots like normal.
Has anyone else had this happen?
Yup,
Same problem over here. I had the problem before. But i fixed it! The only question is how did i do that? short term memory.
I'm trying to solve the problem. If its solved i will let you know.
Till then hang on
I've been trying again today. Still getting the same result, though I figured out if I just leave it when it gets to the bootloader screen, the pc I'm installing from eventually comes up with Error 260.
I'm thinking now that the XP firewall may be the issue, but I'm having trouble disabling it because it's managed by "group policies" (it's a work computer). I'm going to try either finding out which port to unblock, or starting the pc in safe mode so I can disable the firewall altogether.
I fixed the problem with the following softwaretool Hypercore. Just intergrate the Hard spl from olipro. After this the error dissapears.
I Have had this new pda one day yes today and ive managed to f**k it up already
it had windows mobile 5 on it and i wanted to upgrade it to wm6 so i could use flo touch and get the better graphics well i tried at updating and reflashing but all i got was errors and now when i turn it on i get the orange bootloader screen with the text:-
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 10.2.0.8
but nothing else it is now not recognise by the pc and will not boot up even after a hard reset!
please someone help me get through this problem quick!?!
Cheers a bunch Daniel.
Download activesync 4.5 (search for it)
Download this: http://cid-cddbf77985693632.skydrive.live.com/self.aspx/XDA%20files/ROMs/RUU_Prophet_220734_2207114_024721_NVID.exe
In activesync, disable connect through USB.
Run the RUU you downloaded above.
i have downloaded and installed active sync 4.5 as directed on a pc running windows xp and disabled connect through usb by right clicking it on the desktop in the taskbar and clicking connection settings then un-checking the usb connect box. then i connected my prophet and it installed it as a PocketPC USB Sync of something like that and it appears in my computer as a mobile device but when i click it it has nothing in it so i ran the RUU and it asked to update the ROM so i followed the steps but it asked me to make an active sync connection which i cant because the prophet wont turn on after the bootloader the pc recognised it when it was switched off. PLEASE SOMEONE HELP!?!
Unplug the prophet.
Manually enter bootloader and reconnect the device.
then try reflashing the ROM.
Just continue with the RUU unless it gives an error.
i have just right clicked it under device manager and it is recognised as "Windows CE USB Devices" then expands to "PocketPC USB Sync" but how do i manually edit the bootloader if that it was i still have to do sorry im a newbie to this stuff as i said ive only had it one day
it is recognized in the device hardware section but it says there is a fault or something i dont know. there is nothing wrong with the prophet i am 100% sure its just recognised as that because its not turning on properly i think. how do i manually edit the bootloader and what would i need to edit sorry im a newbie at this stuff as you know ive only had it one day and all this because i wanted flo touch
Start up the device normally. Then, press and hold the Comm manager button whilst reseting (stylus into the hole to the left of the power socket). Now, plug the device into the computer and run the RUU.
Thank you so much!!! LIFE SAVER!! its updating now thank you so much il tell you how it goes when its complete TOP HELP!
Thank You Success My Friend!! Woooooooo!! Im A Happy 16 Yr Old :d
Done your GCSEs yet? I'm an unhappy 16 yr old... My Prophet rocks, but my coursework fails...
Do you know how i can put on the flo touch ? when i send across the cab file it installs but doesnt show anything i just clicked on about aswell on the device and it says its still windows mobile 5 ? is it really windows mobile 6 ? i just really want flo touch ?
and nope not yet my GCSE's are in 2 months.
That ROM is WM5. I would suggest updating to a WM6 ROM such as one of Cloudyfas ROMs. Search for it and read all the relavent threads.
To launch the cube, swipe your finger from the top of the screen to the bottom of the screen.
the touch edition or clean edition mate ?
Touch edition will have Touch Flo.
use Prophet Tools to make it faster...
where can i get this prophet tools you speak of ? and what will i have to do i have successfully installed wm6 touch edition now the one you recommended but what about the prophet tools ?
there is a link in my signature to prophet Tools it should all be explained there. also read the new upgrade guide sticky in the WM6 forum. Prophet tools is to help upgrade, so no need for that now...
The touch flo cube should activate in the way i said above.
ok so i have downloaded the little extra on the page of the ShadoW Touch ROM and its called ShadoW Cube and i have installed it yet nothing happens its not even in the device menus. do i need to upgrade it like you said with this tool and how ?
The cube only starts when you slide your finger fRom the bottom of the screen to the top...
I need some expert help please! I have a Hermes (Orange SPV M3100) that I want to flash with a custom ROM but I am having a problem with ActiveSync losing the USB connection at the point that the device enters the bootloader screen. I am also unable to flash using the SD card method. I have flashed a Nike without any problems and I'm usually good with technical stuff so I think there must be something extra I need to do that I have missed. I hope that somebody can spare the time to help me solve the problem. Here are the details:-
I am trying to follow Mr Vanxs guide to flashing the ROM in windows Vista so that I can upgrade it from WM5 to WM6 and apply a custom ROM to load a new TouchFlo style OS. The first step in this process is to flash HardSPL using this guide but my problem with the USB connection won't let me do that. I have unlocked the device using Hermes Unlocker 3a so it is (or should be) SIM and CID unlocked and be SuperCID with HardSPL-1.40 (so maybe I can miss the Mr Vanxs HardSPL step?).
So, when I run the RUUWrapper.exe, choosing the Force option and accepting the messages I eventually get a prompt on the device. At this stage ActiveSync is connected. I click Yes on the device and it enters the bootloader screen which shows 'USB' on the tri-color screen but ActiveSync immediately drops the USB connection. The update then waits for a while then fails with Error 260. I have to do a soft reset to get the device out of the bootloader screen. When the device reboots the Activesync connection comes back to life.
I thought that I maybe don't need to HardSPL first so I tried just going straight to the ROM upgrade but I get the same problem.
Also, I tried following this link to flash using the SD card instead of USB but when I get to step 6 I don't see a confirm message - just the usual bootloader screen (it doesn't help that the screen shot doesn't appear on the link so I'm not even sure if I'm getting the correct screen). Any ideas?
I realise that an answer to this probably already exists somewhere on the forum but I have spent hours trawling through posts and I can't find it so I hope somebody has come across this before and can help me out.
Thanks guys!
Don't worry I solved it by rebooting my PC, skipping the HardSPL and flashing with an official ROM (HTC_TyTN_WWE_3.54.255.3_6275_1.48.00.10_108). I can now apply custom ROMs.
Hi. I have searched the forums, but haven't found the answer I have been looking for, so sorry if this is a repeat.
I am working under Windows 7, installed VMWare and XP Pro on it, and easily installed Hard-SPL and Cracings 6.5. When I went to upgrade the Radio, I was sure to download one without SPL and IPL. I tried to upgrade, but it hung at 2% for at least 5 hours. (I knew it was bad in 2 minutes actually, but decided to wait). Now it will turn on, but to the tri-color boot screen. Tried hard reset (although I didn't really expect it to work). Is there anything that I can do? It shows when I connect it to usb, both on the phone and on the computer.
It is FAR out from under warranty, so thats out, but if there is anything I could try, I would be much obliged for pointers. Thanks a lot!
-Jotek
You need to make the update with RUU 2.5.2
( http://forum.xda-developers.com/showthread.php?t=314952 ).
Try it, if even that does not work (for me it works only with wizard_love ROM
( http://forum.xda-developers.com/show...293480&page=21 loca's post), but not with other cooked ROM's) then you can try WST wizard service tool
( http://forum.xda-developers.com/showthread.php?t=329170 ) to unpack the nbf and load only the OS ROM.
Thanks for the info.
I will try it later this weekend when i get time! (moving to new apt.... sigh... can't feed the addiction)
-jotek
If Tri Colour Screen WST needs to boot into WM OS surely???
How can you use WST if only on bootloader. Please explain as I have similar issues...
Dilbert
I had exactly the same experience as you: Hard-SPL followed by Cracing and then the tri-color screen. This thread helped me revive my G4.
http://forum.xda-developers.com/showthread.php?t=442126
Hey I am having the same problem but with my G3 att 8125. I flashed to 2.26 which I always do before installing any rom then installed X2A Haseebs Iphone Killer and it stalled at 57% for over an hour so I unplugged it and hard-reset it. I have installed this rom about twice and it works fine. Now my phone starts up and goes straight to the Tri-colored bootscreen. When I plug the phone in it displays that it is connected via USB but the computer doesnt recognize it. IPL 2.26, SPL 2.26 as displayed on the screen. PLEASE HELP!
Hi all, I've got the exact same problem as Quadzilla has - any help would be much appreciated!