I'm hoping you folks can help me out. I have tried to upgrade my XDA2 using the Himalaya_WM2003SE_Upgrade but it keeps coming up with:
"Error 150:ROM UPGRADE UTILITY ERROR.
This ROM upgrade utility does not design for your device.
Please get the proper ROM upgrade utility and try again!"
I've got:
FCC ID: NM8HIMALAYAS
IMEI : 351938002885560
Now the unit just gets to the bootloader "SERIAL, v1.06" until I put it in the cradle and it goes to "USB, v1.06". I ran the upgrade following the instructions to the letter but no joy! Am I using the incorrect upgrade utility as the error message says or am I missing something? Any help to restore my XDA2 will be gratefully received!!!
Thanks again!!
which rom are you tryin to upgrade to and provided by who ???
regards
jeetz
I'm basically trying to upgrade my O2 PH10B XDA2 to anything that works! It seems whatever I try, it stays on the bootloader screen with either "Serial or USB" on the display depending whether it's in the cradle or not. I can't do anything with it. I've tried to use the "Himalaya_WM2003SE_Upgrade" utility but as I said, it just tells me that this is not corrrect for my device.
HELP!!
Thanks :roll:
try to reset your device and run himalaya upgrade again
I tried it soooo many times but I still get:
"Error 150:ROM UPGRADE UTILITY ERROR.
This ROM upgrade utility does not design for your device.
Please get the proper ROM upgrade utility and try again!"
I've even tried the O2 Xda_II_172181_Final utility but I still get the same thing. Why does it say it is not designed for my device when I have an O2 Himalaya? If anyone can help I will pledge my undying admiration and possibly even lay down my life for them if required! (sorry, that should have read "wife", not life!) :lol:
glt56 said:
I tried it soooo many times but I still get:
"Error 150:ROM UPGRADE UTILITY ERROR.
This ROM upgrade utility does not design for your device.
Please get the proper ROM upgrade utility and try again!"
I've even tried the O2 Xda_II_172181_Final utility but I still get the same thing. Why does it say it is not designed for my device when I have an O2 Himalaya? If anyone can help I will pledge my undying admiration and possibly even lay down my life for them if required! (sorry, that should have read "wife", not life!) :lol:
Click to expand...
Click to collapse
http://forum.xda-developers.com/viewtopic.php?t=15382&highlight=
try mysterman rom from here dont go for himaupgrade and stuff try to run the setup direct with default radio ....
Success!!!!!
Finally managed to get my XDA2 back to life after some severe CPR & Mouth-to-mouth, and WM2003SEO2UKv2.rar. Thanks for all the suggestions and help.
I also now have a dead M1000.
Where did you get your rom that worked from?
Can you post it please?
Thanks
R
plsssssss help me i also have same problem plsss tell me how u get that pls
Related
I tried to downgrade my XDAII from 1.66wwe to 1.60 version but it got stucked. The screen shows SERIAL v 1.06. I tried to to do it again but unforetunately, it says NO CE ERROR! Please help me on this!
Version 1.06 of the bootloader will not allow you to downgrade. However, you should be able to re-install your original version or later. Just reset your device, put it in the cradle and run the upgrade.
Also suggest you will tend to get better and faster response on your questions if you post a more detailed title about the issue rather than just a call for help.
Ed
Dear friends
I was tring to upgrade my iMate Pocket PC also know as Himalaya with windows2003 SE , while upgrading I faced problems, the upgarde failed and now I am just getting no display and OS too. The only message displayed is
Serial
v1.03
nothing is working please help
bye with regrads,
your unit is still okay; even better that the usb version is showing on the screen. it's simply stuck on bootloader mode. what kind of problems did you encounter resulting in the failed upgrade?
one suggestion i can give before you downgrade is to try and proceed with the upgrade to se. put your unit back on the cradle but don't expect activesync to "recognize" the device. just put it back on the cradle and rerun the upgrade to se.
same thing happened when i upgraded but to wm2005. the screen showed error and the only thing on the screen was the usb version. i simply cradled back the unit and ran the upgrade. worked.
cheers
Hi
Thanks a lot, i tired those steps before and even now I did but its not upgarding I am gettig following error as show i the attachment. Please let me know what to do
thanks a lot
yas
oh, it appears that you have the "wrong country" id issue. i'm not entirely sure as to how to avoid this but i believe it has something to do with the correct rom version (guys, correct me if i'm wrong). where did you get the rom you used for upgrading to se? downgrading might be the only trick if there is no rom for saudi-based users...but if any chaps presently living there and were successful in upgrading their units perhaps you could share the rom version/s you used?
cheers
yasirirfan said:
Hi
Thanks a lot, i tired those steps before and even now I did but its not upgarding I am gettig following error as show i the attachment. Please let me know what to do
thanks a lot
yas
Click to expand...
Click to collapse
To overcome the Country ID Error, first you need to install this tool...
ftp://xda:[email protected]/Tools/ER2003Edit_1_4_26.zip
Open the ROM file you want to upgrade, then change the appropriate 'Operator ID' code, after this click 'Save ROM image'.
Upgrade ur device. You will no longer face the error message.
Hello.
I have a problem I hope someone here can help me to solve..
I have an Orange SPV M3100 that hangs on the Windows Mobile screen when I try to start it.
I'm able to go into bootloader mode, and i have tried using mtty142.exe with the set 14 0 command. It still won't boot. I've also tried to hard reset it.. still won't boot..
What I did was trying to unluck the SIM-lock with the Universal unlocker (HTC_Uni_Unlock_v1) from buzz. At the time I thought universal meant that it worked on all HTC devices (stupid, I know)... And I also thought it was harmless to just try and see if it worked. But I got an error around 92-93% and after that my device won't start. So my radio ROM might be screwed.
I'd like to flash my ROM with the i-mate one (JASJAM_WWE_1.20.305.3_1.20.305.104_1.07.03.10_ship.exe) and then add the ext-rom. But how do I do that when I can just access the bootloader screen? And do you think it will boot again if I'm able to flash it?
Here's some more info about my device:
HERM100
IPL-1.01
SPL-1.04
Thank you very much in advance. Help will be highly appreciated.
No your rom *is* screwed. You can get into bootloader, you can even get to 11% of a dopod etc rom upgrade if you try, but you will not flash a new radio.
You CAN boot the device.
Do a hard reset, but do not press spacebar to reboot after. Instead, do a soft reset. The unit should boot but as you've screwed the radio you will not get a gsm signal and the phone will say unknown sim status.
I know this as I bought one cheap after the owner had done exactly the same as you.
IMEI-check's unlock solution is the only one that works IIRC, and in some cases this re-writes the security area of the phone and repairs similar issues, but in this case I could not get the prog to read.
You need to return the device to HTC - you'll need to pay approx £35 for reflashing back to the orange rom. This is what I had to do.
Currently you cannot book the m3100 in through the web as it's too new, instead email / call them.
http://service.htceurope.com/
edit - or if you're an orange customer ring 150 and act dumb saying it ' won't work'.... :wink:
Richard
What happens if you just leave the phone in bootloader mode and then try to flash any ROM (imate, dopod, htc...)? run 2 times the RomUpgradeUt.exe if you get an error on the 1st try.
If you get an error while running the rom upgrade utility you can monitor the USB port while upgrading (you will see the real error from the bootloader then), there's some more info on this wiki page:
http://wiki.xda-developers.com/index.php?pagename=Hermes_BootLoader
good luck
pof said:
What happens if you just leave the phone in bootloader mode and then try to flash any ROM (imate, dopod, htc...)? run 2 times the RomUpgradeUt.exe if you get an error on the 1st try.
If you get an error while running the rom upgrade utility you can monitor the USB port while upgrading (you will see the real error from the bootloader then), there's some more info on this wiki page:
http://wiki.xda-developers.com/index.php?pagename=Hermes_BootLoader
good luck
Click to expand...
Click to collapse
No, if you want to send it back under warranty do not try to run a rom update as there are no orange rom packages. As described in my post above, it will get to 11% and stop. The device will be in the same state as before, with the same ext rom, but the splash screen and bootloader will have changed.
i.e: it will be bloomin obvious you tried flashing it and failed. Not what you want if you try for a warranty repair....
There is no error from the bootloader - as there is no radio rom present and no security area the upgrade process just hangs.
Richard
fluffcat1 said:
No, if you want to send it back under warranty do not try to run a rom update as there are no orange rom packages.
[...]
i.e: it will be bloomin obvious you tried flashing it and failed. Not what you want if you try for a warranty repair....
Click to expand...
Click to collapse
That's true, do not try to flash any other roms if you want to use the warranty or send the device back...
Thank you very very much for your help guys.
As I'm the administrator of these devices in the company I work for I just grabbed a new SPV and will send this thing back to Orange. It sounded like I'm getting a new one..
Well, I think I've learnt my lession.
Oh, and I have another question. Is there a reg editor I can install on this one so I can remove the app lock? I know I can install java apps, but it's a bit grumpy about apps that needs installation (the developer must be certificated).
Cheers guys.
Hi,
Try to flash a new rom using the SD card method described here:
http://forum.xda-developers.com/viewtopic.php?t=62596
The rom must match your CID. Let us know if it works
pof said:
Hi,
Try to flash a new rom using the SD card method described here:
http://forum.xda-developers.com/viewtopic.php?t=62596
The rom must match your CID. Let us know if it works
Click to expand...
Click to collapse
Errr, did you read the last post? He sent it back......
Richard
I just wanted to let him know there's a possible solution, it just in case he still has the unit
pof said:
I just wanted to let him know there's a possible solution, it just in case he still has the unit
Click to expand...
Click to collapse
Maybe his search is broken as well as his old phone eh?.... :roll:
fluffcat1 said:
You need to return the device to HTC - you'll need to pay approx £35 for reflashing back to the orange rom. This is what I had to do.
Click to expand...
Click to collapse
Sorry to take the thread a bit OT, but just wanted to confirm this again.
So, if I flashed my M3100 with a different ROM, and then had to return the phone to Orange for repair for a different reason, I can send it back to HTC just to have the ROM reflashed, and then send the phone to Orange to get the repairs done?
I've been hesitating on whether to flash the phone with a non-Orange ROM because I didn't want to give up the ability to obtain warranty repair (as there is no ROM upgrade yet). If it's just a matter of £35 and then everything else as normal, maybe it's not so bad...
Thanks!
My SPV M3100 won't start!!!
I also did this, so if anyone can find a solution it would be greatly appreciated.
Also tried this and it didn't work for me:
Try to flash a new rom using the SD card method described here:
http://forum.xda-developers.com/viewtopic.php?t=62596
"I have a problem I hope someone here can help me to solve..
I have an Orange SPV M3100 that hangs on the Windows Mobile screen when I try to start it.
I'm able to go into bootloader mode, and i have tried using mtty142.exe with the set 14 0 command. It still won't boot. I've also tried to hard reset it.. still won't boot..
What I did was trying to unluck the SIM-lock with the Universal unlocker (HTC_Uni_Unlock_v1) from buzz. At the time I thought universal meant that it worked on all HTC devices (stupid, I know)... "
rachelm700 said:
I also did this, so if anyone can find a solution it would be greatly appreciated.
Also tried this and it didn't work for me:
Try to flash a new rom using the SD card method described here:
http://forum.xda-developers.com/viewtopic.php?t=62596
"I have a problem I hope someone here can help me to solve..
I have an Orange SPV M3100 that hangs on the Windows Mobile screen when I try to start it.
I'm able to go into bootloader mode, and i have tried using mtty142.exe with the set 14 0 command. It still won't boot. I've also tried to hard reset it.. still won't boot..
What I did was trying to unluck the SIM-lock with the Universal unlocker (HTC_Uni_Unlock_v1) from buzz. At the time I thought universal meant that it worked on all HTC devices (stupid, I know)... "
Click to expand...
Click to collapse
the above link doesnt work?
zohaer21 said:
the above link doesnt work?
Click to expand...
Click to collapse
IIRC it is this link on the new forum:
http://forum.xda-developers.com/showthread.php?t=277281
spv m3100 don't start
hello guys
I have the same problem about spv m3100. I used "universal unlock tool" to unlock my device and now it don't start,don't boot...I tried the Hermes SD Card flashing methods with qtek001 rom and, a white screen with "loading...." appears for 2 second and then nothing else appened. I think that the method is right but I need to use a different software. what do you think about?
please help me
thankksssss
My SPV M3100 won't start
SD card method is no good as there is no upgrade from Orange until January.
Tried to do a radio upgrade explained here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms
But it didn't work just came up with connection error, tried to monitor USB but nothing showed up to find out why, althouth mtty commands always do show up in USB Monitor.
Still have a brick and looking for a solution, hopefully, someday, please someone help me I am loosing my mind.
Hello
How to enter boot mode on HTC 200 ?
My htc hangs on HTC screen.
I'm trying to reflash it.
Thanx
Chris
@chrisro, Please read the wiki:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
http://wiki.xda-developers.com/index.php?pagename=Hermes_Resets
Thank you very much.
Greets form Poland !
Chris
I will paypal someone 50.00 if they can help me revive my dead 8525.
Thanks
whoah....talk about a lurker.
But if you want us to help. we must know the systems
It is an 8525 (Cingular)
I did Pof's upgrade to unlock it. I guess it did not take. (I did not know it was still 1.06) Did the upgrade to unlock and then I tried the following update:
Hermes_1.18.416.1_1.18.416.101_1.14.00.10_WWE_Ship.exe
Now when it boots it I get a background of Rainbow-like noise then the windows mobile screen comes up and stays there. I have tried doin the various updates (Cingular ones) and always get the Vendor ID Error.
Ask any other questions anyone has.
Thanks
Can you put the device into bootloader mode by pressing 'Ok' & 'Power Off' buttons together and resetting the device??
you should try to re-install the cingular 1.34 rom...if you get the vendor id error, run it again ...see the wiki regarding vendor id error
I can go into bootloader. I have done the 1.34 but, it says Invalid Vendor ID. I do it again. (Like the Wiki says but same thing happens).
No one has any ideas?
See if you get the same error with the I-Mate 1.20 ROm.
Have you tried leaving it in bootloader mode and updating it with a TMOBILE rom??? i noticed on your profile that your with TMOBILE... try one of the JASJAM roms....
i am gonna go on a limb here. maybe try to run the step listed to downgrade the bootloader in this thread http://forum.xda-developers.com/showthread.php?t=284401 maybe it will work from boot loader. can't hurt to give it a shot...
I'm Cooking a special cake for you
Hi
I'm cooking a new special ROM edition to you right now, please send me an email with the subject (CAKE) and I'll return you the link for the ROM Upgrade ,I hope it fix your problem
my email is [email protected]
SORRY,,Problems faced, I can't finish this
I sent you the email. Yell back when you have it.
Thanks
Are you in Illinois by chance?
Nope, in Dallas, TX.
So i wanted to flash my cingular 8125 to windows mobile 6, so i downloaded this:
(BIG MISTAKE)
http://www.tradebit.com/filedetail.php/2559279-Software-Programs-Cell-Phone-Programs
and i followed the instructions and after i hard reseted my phone, it booted to a white screen. I have tryed reflashing, going into bootloader mode and reflashing, and i nothing helps.
can one of the experts on this forum please help me???!!!
thanks
i need help assap!! lol
i dont care even if i flash back to winmo5, I JUST WANNA UNBRICK
dahdout said:
So i wanted to flash my cingular 8125 to windows mobile 6, so i downloaded this:
(BIG MISTAKE)
http://www.tradebit.com/filedetail.php/2559279-Software-Programs-Cell-Phone-Programs
and i followed the instructions and after i hard reseted my phone, it booted to a white screen. I have tryed reflashing, going into bootloader mode and reflashing, and i nothing helps.
can one of the experts on this forum please help me???!!!
thanks
i need help assap!! lol
i dont care even if i flash back to winmo5, I JUST WANNA UNBRICK
Click to expand...
Click to collapse
What IPL/SPL it displays now ? ,Does it get into Bootloaders ? if it still does than download and flash 'wizard_love_rom' hope it'll recover back.
RE:
It just boots into a white screen. If i hold the camera and power buttons together it boots into bootloader mode, and says USB in the bottom corner. (when i am conncected via usb) but the problem is that active sync doesnt recognize it in bootloader mode. I have tried flashing it in many different ways and i have had no success.
When i go home i will try wizard_love_rom.
and as for the IPL/SPL, i will also check that when i get home.
Where can i download the wizard_love_rom?
Thanks for the help !
RE:2
Hello,
Mr IPL and SPL are both 2.25.0001
My GSM: 02.25.11
My OS: 2.18.0.0
Good News
So, I flashed my phone with the "Wizard_Love_2.26.10.2_WWE_Novii_CF2.rar"
which i found the download for over a quick google search, and now i want to update to winmo6 or 6.1.
Can you send me the link for the easiest way to do it on a G4 cingular 8125 (HTC Wizard.)
I have never CID unlocked, which was probably why i got the white screen earlier. but do i need to do it know that i am on the wizard love rom?
please help,
thanks
dahdout said:
So, I flashed my phone with the "Wizard_Love_2.26.10.2_WWE_Novii_CF2.rar"
which i found the download for over a quick google search, and now i want to update to winmo6 or 6.1.
Can you send me the link for the easiest way to do it on a G4 cingular 8125 (HTC Wizard.)
I have never CID unlocked, which was probably why i got the white screen earlier. but do i need to do it know that i am on the wizard love rom?
please help,
thanks
Click to expand...
Click to collapse
Glade its working again !
You got a G4 device,it cannot be CID unlocked,but however,it can be upgraded to wm6 or 6.1,read the methods 'HardSPL' or 'SoftSPL' posted as stickies in the G4 forum for upgrading to wm6 or 6.1.
re:3
thanks, you really saved me with your help!
dahdout said:
thanks, you really saved me with your help!
Click to expand...
Click to collapse
Thanks !
Glade you got it working
sorry, but i need help... again
Ok,
I know that this may be getting a little annoying for you and im sorry for that, but i need your help on this. I am currently running the wizard love rom. And I have Hard SCP'd.
I have to problems:
1. My EDGE doesn't work, i only get GPRS speed data.
2. I can't upgrade to any new rom..... i always get "ERROR [300] Get a newer update utility!"
How can I fix both of these problems?
I have searched forums and google and nothing has come up.
dahdout said:
Ok,
I know that this may be getting a little annoying for you and im sorry for that, but i need your help on this. I am currently running the wizard love rom. And I have Hard SCP'd.
I have to problems:
1. My EDGE doesn't work, i only get GPRS speed data.
2. I can't upgrade to any new rom..... i always get "ERROR [300] Get a newer update utility!"
How can I fix both of these problems?
I have searched forums and google and nothing has come up.
Click to expand...
Click to collapse
ok,for error (300)you can use the RUU MUNS already posted in the 'HardSPL' thread,download the RUU_MUNS application extract it to a folder and copy and paste all the files of this extracted to the folder of the Rom replacing all the RUU files in that folder or copy the nk.nbf folder in the Rom to the extracted folder of the RUU_MUNS and then run the RUU,it will start to flash and complete and hopefully fully boot up.
For edge or gprs,you'll have to get network settings of your network carrier or check out the thread from where you downloaded the rom,its uaually posted there or check out the 'Network' thread.
Aquestion to Zabardast_1 ?
294 error , invalid vender ID
what does that means & asolution to it during rom update
ERROR [294] : INVALID VENDER ID
One of these error messages will appear when you use the wrong RUU to do the upgrade. RUU will check if the Model ID and Language ID are compatible with the device. Make sure you use the appropriate RUU tool to upgrade.