help me please my device is dead how can i backup it agian
if any one know help me the story is when i do a hard rest and make an upgare the imate tyoe in the screen that is erasing rom and the is shut down and now when i repack to update is give me this screen shot what i do
Try pressing "Power Button" + "Reset Button" + Directional Pad (the center) Button" then you will go to boot screen.. If you see "Serial" on top and "v1.06" below try docking the device on the cradle then reflash.. reply asap with the result..
i try this but no answer
what can i do please
alloooooooooooooooooo i want any answer plz
Here... Put this file "HimaClearJumpCode.exe " in the same directory as the ROM and installer and it should work this time...
Also, try to use the power supply connected to the cradle, sometimes the power provided through the USB cradle is not enough.
If it works, chances are you will get another error "Country Error". If that's the case, use the attached file "himaupgradeut_197.exe" instead, this will skip the country check.
Good Luck!
Rayan
my friend it dose not work what can i do please i want to repaire it and i can't do that and how does it work please insert some picture about the steps to understand that
and thank you again about your steps
Please describe what you see on the PDA screen when you power up?
Does it boots all the way into the Windows Mobile Today screen?
Do you only see the word "Serial" on a blank screen?
Please provide more details.
the details is
1- when i put the pda in the cradel it is give me the red light but this happen without put the battery in the pda the problem is when i put the battery in the pda it give me no light
2- i changed the battery but no answer
3- i try to put it in the cradel and recharge for 1 night and put it in the pda but now answer
4- i read abut reflashing but this is very hard and i can't see any replay abut that
5- now i want to tell you the summry when i put the pda with the battery and it full cahrge it give me now answer and the active syn did not find any thing and on the screen there is nothing not serial and not usb ver the screen is black
please tell me i'm in egypte and no one know to repaire it
what can i do
Sorry, but as far as I know, you will not be able to reflash if you can't boot or at least see the bootloader screen (blank screen with SERIAL text).
May I ask, what caused this problem in the first place?
What model do you have? Himalaya, Alpine, Wallaby, etc...
i have himalaya 1.2
is this write or not
where are you
do you know waht i must to do my friend
where are you
no one know
Can you tell me what will you see if in your screen if you press the "Power Button" + "reset Button" + Directional Pad Button (The center one)? cuz thats the best you ca do...
my friend when i connected the power my device is not work how?! because when i put the battery in the device it gives me that no power in the device ,then i changed the battery but the problem still appear when i put the device in the cradel the red light becomes work but this happend when i put it without battery now when i put the battery the device turn off the red light and not give me any thing now i want to give the device power
how can i do that and how can i fix the screen that tell me that the device is not in the cradel this screen is apper for me my frindes
and when i press that buttons nothig happen i don't know waht but now i want to give the device the power how can i do that do you have any answer about that
Related
Dear Pro!
please help me! My XDAII uprom finish ! it alway Hardreset .I uprom again It error and now bootloader not run anymore .i'don't know why .Please help me!
Thanks !
ok, don't lose it just yet.
first thing to try is the "vulcan death grip" on the pda; simultaneously press the power button, soft-reset button, and middle button on the scroller on the front of the PDA to enter bootloader mode, if you do it right, then the version number will appear at the bottom of the screen (i.e v1.06) and you will thus be in bootloader mode.
failing that, remove the battery from the PDA, and leave it like that for about an hour so the backup battery can die, then put the battery back in and pray it enters bootloader mode.
PLEASE SOMEBODY HELP ME
TWO WEEK AGO MY ATOM WAS DEAD
IAM HAVE BEEN TRY TO HARD RESET ALSO MN1 BOOT LOADER ( POWER BUTTON+CAMERA BUTTON). BUT DOESN'T WORK.
SO TODAY IAM TRY TO FLASH BOOT LOADER FROM JTAG PORT, AFTER FINISH FLASH PROGRAMED MY ATOM STILL DEAD.
SOMEBODY PLEASE HELP...
Okay, firstly dont put everything in caps.. its EXTREMELY annoying. Secondly, the device turns on correct? if it does then just try flashing from either your PC through Activesync OR via a memory card with a ROM on it. Consider using a stable ROM from either a ROM Chef or the O2/MWG website.
Aegishua said:
Okay, firstly dont put everything in caps.. its EXTREMELY annoying. Secondly, the device turns on correct? if it does then just try flashing from either your PC through Activesync OR via a memory card with a ROM on it. Consider using a stable ROM from either a ROM Chef or the O2/MWG website.
Click to expand...
Click to collapse
Haii.. thank you for your respon soon.
for your information my PDA totaly malfuction. that no respon when iam press power buton+camera buttonto go to MN1 boot loader .
only red lamp on when the PDA connect with charger battery.
Hmm okay.. so that means it still charges. You should try charging it for an extended period of time and then turning the device on. If the device comes up with the Manufacturer logo then you should just soft reset it and hold down your bootloader combination and go from there. However, if it doesnt even come up with the Manufacturer logo then you should consider getting it repaired.
Hii...i was do to charge my PDA also iam test with volt meter that battery is full power 4,2 volt dc.
So i try to push power button than my PDA doesn't start till now....
Atom Brick Solution...
suga_ngr said:
Hii...i was do to charge my PDA also iam test with volt meter that battery is full power 4,2 volt dc.
So i try to push power button than my PDA doesn't start till now....
Click to expand...
Click to collapse
Have you search on wiki?
I've been through that condition, last night actually when I pressed the wrong button (Power Button) when the MN1 bootloader looked for diskimg.nb0.
My device was near to death. I couldn't find the MN1 bootloader on my device's screen when I pressed the CAMERA+RESET(stylus). It remains dead until :
-I search the solution on http://wiki.xda-developers.com/index.php?pagename=ATOM_BRICK, I could see my device running its MN1 Bootloader
and looked for the ROM (diskimg.nb0) again and continued the ROM installation process
How to get the diskimg.nb0 please read this page :
http://wiki.xda-developers.com/index.php?pagename=ATOM_SDCARD
Maybe atom pure had the same step with atom exec when we try to solve the Brick Problem.
Cheers...
TOM PURE Dead
With my experience my atom was hardware broken.
somebody please tell me where i can buy atom hardware cause iam very love my atom...
try th!s tr!ck (cb ini mas)
yesterday 09 jan 10 it's happened same to me.
my case is downgrade from h3llow0rd1 6.1 to PD4v!et 19971 by m3dk!d.
then atom hang up.. dead! no screen, cann't boot or ON.. but still can charging
This tr!ck may be this could help u..
1. charging, look red lamp is on
2. then try replace battery, then put back on. it will blink (button call and end call will blinK)
3. with stylus try reset with pressing record button
4. if your lucky then it will show you boot loader screen
Now my atom is back again using Hell0w0rd R0M ... (^_^)
suga_ngr said:
With my experience my atom was hardware broken.
somebody please tell me where i can buy atom hardware cause iam very love my atom...
Click to expand...
Click to collapse
Entering BootLoader Mode:
1.Remove Battery
2.Press Camera button and hold it while insert the battery.
3.Press Reset with stylus (keep holding camera button)
If you're lucky, you'll be directed to bootloader mode.
try to push the power & camera button together while inserting the battery and then enter the bootloader mode camera+reset button.
My Atom Life (was) dead, too
..but only for awhile
this happened when I tried to flash this Bajok ROM.
I'm not new to flashing, but that kinda make me 'a little' careless this time.
I transferred the .dio file using active sync explorer while doing other stuff with my laptop.. soon after, I see that the file transfer is done, cause the window is closed. As usual, I do the rec button + reset ritual and flashed away..
I again continued my other works and got mesmerized in it for a moment or two.
Half an hour later I realized that my atom has been showing bootscreen for quite some time..
My first failed flash! Well, I thought, this is it...
Just to make sure, I pulled out the battery, put it back again and reboot.. still the same stuckness... Then, I figured that since this was caused by ROm flashing failure, why dont check the .dio file? So I did. I pulled out the memory card, put it in a card reader and explore it.. I notice that the .dio file is only 18 megs.. whatta..? The original .dio is like 70 megs, so it must had been transferred it incomplete.
So with high hope, I retrasferred the file, this time completely.
I inserted again the battery and repeated the rec button + reset ritual..
Boot loader appeared and flashed away like a charm!
This is my first post, so hy guys...... (i hope ive posted it on the wright location)
when i'm pressing the Turn on button it comes only the green "HTC" logo in the middle Without the system information in the left bottom i've to be onest im getting scared cause ive tried a lot of hard reset and nothing happens....
another problem is that i cant connect it at the pc because the connection by usb dont work.....what can i do?????
you're device is stuck just before flashing a rom (that happens when you perform task29 for instance)
Quote: "If you get a white screen with "hTC" in the middle then you need to take out your battery and enter bootloader mode manually before continuing (take battery out and put it back in, then hold the volume down button and briefly press the power button. Keep holding the volume down button until the bootloader screen appears)"
after that you can flash your device with any rom
Good Luck
get into bootloader mode and then flash a newer radio ROM. solved the problem for me.
p.s. read thoroughly about the correct radio for ur phone before flashing one
abuawab said:
you're device is stuck just before flashing a rom (that happens when you perform task29 for instance)
Quote: "If you get a white screen with "hTC" in the middle then you need to take out your battery and enter bootloader mode manually before continuing (take battery out and put it back in, then hold the volume down button and briefly press the power button. Keep holding the volume down button until the bootloader screen appears)"
after that you can flash your device with any rom
Good Luck
Click to expand...
Click to collapse
it work mate thank you a lot!!!
anytime
PLease can anyone let me know the process to load a rom onto a HD2 that will not boot up....? Windows mobile device center will not detect it either. Bootlogger screen says I have SPL-2.08.HSPL 8G XE, and underneath it says CotullaHSPL if that is any help. I would really appreciate any help!
lisah456 said:
PLease can anyone let me know the process to load a rom onto a HD2 that will not boot up....? Windows mobile device center will not detect it either. Bootlogger screen says I have SPL-2.08.HSPL 8G XE, and underneath it says CotullaHSPL if that is any help. I would really appreciate any help!
Click to expand...
Click to collapse
After task 29 you have to flash a ROM. Task 29 wipes your device so if you don't hold down the volume down key at the end of task 29 it will not have any operating system. Just remove the battery and hold down the volume down key till you see the bootloader screen. Then flash your ROM and all is ok.
after task29,when your device reboot
press botton "volume down" and will go in bootloader mode
now if you have your device stuck in white screen,remove battery cover
press red botton for softrest and press "Volume down" botton
bobsbbq said:
After task 29 you have to flash a ROM. Task 29 wipes your device so if you don't hold down the volume down key at the end of task 29 it will not have any operating system. Just remove the battery and hold down the volume down key till you see the bootloader screen. Then flash your ROM and all is ok.
Click to expand...
Click to collapse
opsss..sorry bob
i have look now your post
My problem is that the windows mobile says that the phone is not connected?
What do I do now?
Thanking you in advanced,
Henry
kikimax said:
My problem is that the windows mobile says that the phone is not connected?
What do I do now?
Thanking you in advanced,
Henry
Click to expand...
Click to collapse
It won't because you're in the bootloader. Does it say USB at the bottom of the bootloader screen? As long as it says USB when the phone is plugged into your computer, flash a ROM and be happy
Hello!
And what if my hd2 not entering into the boot loader?
Thanx in advance
There is only one way to get into the bootloader.
Hold down volume and keep it down....
After that press the start button and your phone will boot up.
Now you will see the tree colored screen and you're in the bootloader.
Goodluck.
same problem..connected to pc but wmdc doesn't discover it so i can't flash anything.and sd card flash doesn't help.what can i do now?
wopin80 said:
same problem..connected to pc but wmdc doesn't discover it so i can't flash anything.and sd card flash doesn't help.what can i do now?
Click to expand...
Click to collapse
When you are in the bootloader screen, connect the phone to the computer /with the usb cable/ on the same bootloader screen it will change to USB - look at the bottom of the screen:
Open the folder - on your computer - where the ROM you want to flash is:
find the "RomUpdate*.exe" or "Install.exe" /if Android it will most likely say "DAF.exe" - run it as Administrator/ file and run it. Do as it says on the screen.
Do not disconnect the cable, do not touch the device. When it is finnished it will restart the device, disconnect the cable and enjoy your new OS.
wopin80 said:
same problem..connected to pc but wmdc doesn't discover it so i can't flash anything.and sd card flash doesn't help.what can i do now?
Click to expand...
Click to collapse
use a <4gb or preferably <2gb sd card - class 4 or 2 with LEOIMG.nbh.
HSPL3_pkg after that - make sure .nbh (as above on sd root) is your stock and you CLEAN-reinstall bootloader.
ps:
Then hspl, then radio, then magldr, then windows 7, the hacks, then call M$= LIVE!
Hi guys i have a similar problem. After task 29 i went into the bootloader but can't install any rom whatsoever. I have SPL 3.03 on my devide, mind no not hard spl but SPL. Can anyone please help me solve this issue? I also tried to flash using sd card but it doesn't work. Please help me save my hd2. Thanks in advance.
tmo-hd2 wont go into bootloader after task29
Hi guys, i am facing exact same thing which dannytgt faced (http://forum.xda-developers.com/show...count=1)...but with no luck what so ever.....was running a stock rom in my hd2 3.14....wanted to try wp7 and did a task29....after that...hd2 doesnt go into bootloader screen....tried all possible combinations with/without sd,sim, holding vol down, vol up, both with power tapped...power holded etc etc...hd2 always goes into stick together screen and doesnt progress as there is os to load....opened up the mobile and tried with a pin to push the vol down switch directly also....all hardware keys were working gr8 (including vol down and up and power keys) whn win 6.5/android was running.
i know for the fact that this is reversable....if only my hd2 can get to bootloader...i will hv os running in a jiffy....
any ideas ppl? my hd2 is 3 months old ...no warrenty cos i bought it in US and using it in india..
bootloader dont load
some more details...tried to task29 (doloop) with 100% success and then my tmo hd2 wont go into bootscreen what ever i do...its stuck for ever in "stick together"...i know there is no os to load...but i dont understand y cant my hd2 go intobootloader
so far i tried
with holding volume down and power key with a single tap
with holding volume down and holding power key
with holding volume down, volume up and power key with a single tap
with holding volume down and reset button
with/without sim
with/without SD
with/without plug in wall charger
with/without plug to pc via usb cable
observations...when i pull out the battery and put it back in and then connect to computer when the phone is still off....the charging indicator LED glows in orange.
when in this mode if i switch the phone on with power/end key....it doent start...i have to pull the usb out, the orange LED still glows...and if i tap the power/end key nothing happenes...i have to pullout the battery to get it to start and eventually get stuck in "stick together"..
would really appriciate if any1 can help me get my hd2 into bootloader screen...
gdsbalaji said:
some more details...tried to task29 (doloop) with 100% success and then my tmo hd2 wont go into bootscreen what ever i do...its stuck for ever in "stick together"...i know there is no os to load...but i dont understand y cant my hd2 go intobootloader
so far i tried
with holding volume down and power key with a single tap
with holding volume down and holding power key
with holding volume down, volume up and power key with a single tap
with holding volume down and reset button
with/without sim
with/without SD
with/without plug in wall charger
with/without plug to pc via usb cable
observations...when i pull out the battery and put it back in and then connect to computer when the phone is still off....the charging indicator LED glows in orange.
when in this mode if i switch the phone on with power/end key....it doent start...i have to pull the usb out, the orange LED still glows...and if i tap the power/end key nothing happenes...i have to pullout the battery to get it to start and eventually get stuck in "stick together"..
would really appriciate if any1 can help me get my hd2 into bootloader screen...
Click to expand...
Click to collapse
Isn't it ironic: Stick together!...
There is a guide on How to get back from WP7 here on the forum.
First i would sugest to reformat the card from WP7 bul...
If i understand correctly, you can't get into bootloader or magldr!?
So you can't do nothing?
You can try this sollution and if it doesn't work, go to the service center to reset it totaly.
There was a guy with the same problem here:
Originally Posted by splinters69 View Post
This (or something similar) happened to me. I powered down my phone but did not take out the battery and it restarted the part that loads the win 7 rom while I still got the screen with the coloured bands on.
Try, taking out the battery for 10 seconds or so then put it in while holding the volume down key and powering up.
Got stock ROM back in first time but kiss goodbye to the data on your SD card. I had to use a Canon camera to reformat the card to get back the 14GB it was hiding.
This WORKED. Thanks a TON splinters69.
For future uses, this is what I did.
1. Took out the battery for about 30 seconds.
2. Put one of the LEOIMG.NBH on storage card
3. After putting the battery held the volume down button and pressed power button.
4. It went into HSPL mode straight away and started loading the win 6.5 OS.
You saved the day Splinters69. Thanks to Clydeb1 too for that modelIDcheckbypass.
http://forum.xda-developers.com/showthread.php?t=913081
lms1407 said:
Isn't it ironic: Stick together!...
There is a guide on How to get back from WP7 here on the forum.
First i would sugest to reformat the card from WP7 bul...
If i understand correctly, you can't get into bootloader or magldr!?
So you can't do nothing?
You can try this sollution and if it doesn't work, go to the service center to reset it totaly.
There was a guy with the same problem here:
Originally Posted by splinters69 View Post
This (or something similar) happened to me. I powered down my phone but did not take out the battery and it restarted the part that loads the win 7 rom while I still got the screen with the coloured bands on.
Try, taking out the battery for 10 seconds or so then put it in while holding the volume down key and powering up.
Got stock ROM back in first time but kiss goodbye to the data on your SD card. I had to use a Canon camera to reformat the card to get back the 14GB it was hiding.
This WORKED. Thanks a TON splinters69.
For future uses, this is what I did.
1. Took out the battery for about 30 seconds.
2. Put one of the LEOIMG.NBH on storage card
3. After putting the battery held the volume down button and pressed power button.
4. It went into HSPL mode straight away and started loading the win 6.5 OS.
You saved the day Splinters69. Thanks to Clydeb1 too for that modelIDcheckbypass.
http://forum.xda-developers.com/showthread.php?t=913081
Click to expand...
Click to collapse
I hvnt even instaled MGALDR yet....task29 and hd2 went into trouble...need to get to bootloader to save it now
Tried this as well before posting....hv a 2gb sd card>formatted to fat 32> stock rrunbh to leoimg.nbh > moved to root of sd card....but this can only work if bootloader can be initiated right? i cant get to boot loader
resolved the problem myself.....hd2 is working like a charm....thanks for all your support.
SOLVED {bootloader dont load}
checkout the solution for my problem here....might help u as well.
http://forum.xda-developers.com/showpost.php?p=10644926&postcount=4
______________________________
if you feel this helped...thank me
hi there i have realy big problem i have done that task 29 trick with the blackstone advangeruu and there was something wrong after restart so i pulled the battery out.
now my phone wont do any thing when i hold nowd the start button en volume down i know it has no os. but is there any way to get in the bootloader screen hope some one can help me beceasue i need my phone.
DeAdMaNwa said:
hi there i have realy big problem i have done that task 29 trick with the blackstone advangeruu and there was something wrong after restart so i pulled the battery out.
now my phone wont do any thing when i hold nowd the start button en volume down i know it has no os. but is there any way to get in the bootloader screen hope some one can help me beceasue i need my phone.
Click to expand...
Click to collapse
Man, did you say blackstone? You should go into Blackstone forum
To go into bootloader, turn off the phone. Press volume down button and the POWER ON button (not start button) at the same time until the screen appear. It works on both Leo and Black Stone
Goodluck
@All
i've Bricked (killed) my HTC mega, i just flash it with wrong file and after that it stuck on HTC logo so i just connected it with MTTY and used few commands and it doesn't power on , mean doesn't take power at all now , i used following commands.
1) i connected it with MTTY in Bootloader.
2) i open MTTY
3) i type info 8 (it shows me it have bad blocks)
4) i type task 2a (it says can't reapir Bad Blocks)
5) i type task 8 phone turned off and then no power at all.
i think there is a solution with JTAG to revive dead phone there was no problem at all with Phone before only need to change from Chinese to English language.
if there is any help kindly post it here.
Take Care
ENJOY
your device go in bootloader? If yes download original rom for your device, power on device with volume down pressed (three colored bars appears), connect with usb and flash original rom. For download correct rom search in this thread:
http://forum.xda-developers.com/showthread.php?t=578915
or search your rom here:
http://htcpedia.com/soft/mega-touch2-rom.html
http://shipped-roms.com/shipped/Mega/
If you have issue executing this procedure please i try to help you
fabcal the phone doesnt even turn on as the thread owner mentioned ... so none of your methods will work for him ....
LtBlue said:
fabcal the phone doesnt even turn on as the thread owner mentioned ... so none of your methods will work for him ....
Click to expand...
Click to collapse
it is true that he says that the phone will not turn on. But from my experience in the assistance of computers, the user loads the fact that the system is reported as "not turn on ". You have no idea how many times I went home carrying the replacement power supply because they said "not turn on", when they appeared "disk boot failure!" and the same thing I already happened with Italian users of smart phones. White screen at power on, boot loader ok but the owner stated that power on. I explained?
Ascolta
Trascrizione fonetica
Dizionario - Visualizza dizionario dettagliatocongiunzione0.and
Project dead