Dear Pro!
please help me! My XDAII uprom finish ! it alway Hardreset .I uprom again It error and now bootloader not run anymore .i'don't know why .Please help me!
Thanks !
ok, don't lose it just yet.
first thing to try is the "vulcan death grip" on the pda; simultaneously press the power button, soft-reset button, and middle button on the scroller on the front of the PDA to enter bootloader mode, if you do it right, then the version number will appear at the bottom of the screen (i.e v1.06) and you will thus be in bootloader mode.
failing that, remove the battery from the PDA, and leave it like that for about an hour so the backup battery can die, then put the battery back in and pray it enters bootloader mode.
Related
help me please my device is dead how can i backup it agian
if any one know help me the story is when i do a hard rest and make an upgare the imate tyoe in the screen that is erasing rom and the is shut down and now when i repack to update is give me this screen shot what i do
Try pressing "Power Button" + "Reset Button" + Directional Pad (the center) Button" then you will go to boot screen.. If you see "Serial" on top and "v1.06" below try docking the device on the cradle then reflash.. reply asap with the result..
i try this but no answer
what can i do please
alloooooooooooooooooo i want any answer plz
Here... Put this file "HimaClearJumpCode.exe " in the same directory as the ROM and installer and it should work this time...
Also, try to use the power supply connected to the cradle, sometimes the power provided through the USB cradle is not enough.
If it works, chances are you will get another error "Country Error". If that's the case, use the attached file "himaupgradeut_197.exe" instead, this will skip the country check.
Good Luck!
Rayan
my friend it dose not work what can i do please i want to repaire it and i can't do that and how does it work please insert some picture about the steps to understand that
and thank you again about your steps
Please describe what you see on the PDA screen when you power up?
Does it boots all the way into the Windows Mobile Today screen?
Do you only see the word "Serial" on a blank screen?
Please provide more details.
the details is
1- when i put the pda in the cradel it is give me the red light but this happen without put the battery in the pda the problem is when i put the battery in the pda it give me no light
2- i changed the battery but no answer
3- i try to put it in the cradel and recharge for 1 night and put it in the pda but now answer
4- i read abut reflashing but this is very hard and i can't see any replay abut that
5- now i want to tell you the summry when i put the pda with the battery and it full cahrge it give me now answer and the active syn did not find any thing and on the screen there is nothing not serial and not usb ver the screen is black
please tell me i'm in egypte and no one know to repaire it
what can i do
Sorry, but as far as I know, you will not be able to reflash if you can't boot or at least see the bootloader screen (blank screen with SERIAL text).
May I ask, what caused this problem in the first place?
What model do you have? Himalaya, Alpine, Wallaby, etc...
i have himalaya 1.2
is this write or not
where are you
do you know waht i must to do my friend
where are you
no one know
Can you tell me what will you see if in your screen if you press the "Power Button" + "reset Button" + Directional Pad Button (The center one)? cuz thats the best you ca do...
my friend when i connected the power my device is not work how?! because when i put the battery in the device it gives me that no power in the device ,then i changed the battery but the problem still appear when i put the device in the cradel the red light becomes work but this happend when i put it without battery now when i put the battery the device turn off the red light and not give me any thing now i want to give the device power
how can i do that and how can i fix the screen that tell me that the device is not in the cradel this screen is apper for me my frindes
and when i press that buttons nothig happen i don't know waht but now i want to give the device the power how can i do that do you have any answer about that
Hi dear freinds I upgrade my phone edition ppc to wm5 successfully after finishing and hard reseting my device this message raise(("Device authentication")) so I can't do anything with my ppc and I try using camera button and power for gettin into bootloader but it does't work can somebody help me How can I get into bootloader mode for upgrading again thanks
Push and hold the DPad(the button between the RED and GREEN buttons) and the power button and put the stick(stylus) in the hole(there is one near the chharge/USB plug) to resset your device.
Dont release the power and DPad buttons until in the screen you read SERIAL.
Uala you're in bootloader mode
Put the device in the cradle and it should change tio USB
Do the upgrade/downgrade ............. as you want
Regards
thats right
yup thats the right way bro... 8)
PLEASE SOMEBODY HELP ME
TWO WEEK AGO MY ATOM WAS DEAD
IAM HAVE BEEN TRY TO HARD RESET ALSO MN1 BOOT LOADER ( POWER BUTTON+CAMERA BUTTON). BUT DOESN'T WORK.
SO TODAY IAM TRY TO FLASH BOOT LOADER FROM JTAG PORT, AFTER FINISH FLASH PROGRAMED MY ATOM STILL DEAD.
SOMEBODY PLEASE HELP...
Okay, firstly dont put everything in caps.. its EXTREMELY annoying. Secondly, the device turns on correct? if it does then just try flashing from either your PC through Activesync OR via a memory card with a ROM on it. Consider using a stable ROM from either a ROM Chef or the O2/MWG website.
Aegishua said:
Okay, firstly dont put everything in caps.. its EXTREMELY annoying. Secondly, the device turns on correct? if it does then just try flashing from either your PC through Activesync OR via a memory card with a ROM on it. Consider using a stable ROM from either a ROM Chef or the O2/MWG website.
Click to expand...
Click to collapse
Haii.. thank you for your respon soon.
for your information my PDA totaly malfuction. that no respon when iam press power buton+camera buttonto go to MN1 boot loader .
only red lamp on when the PDA connect with charger battery.
Hmm okay.. so that means it still charges. You should try charging it for an extended period of time and then turning the device on. If the device comes up with the Manufacturer logo then you should just soft reset it and hold down your bootloader combination and go from there. However, if it doesnt even come up with the Manufacturer logo then you should consider getting it repaired.
Hii...i was do to charge my PDA also iam test with volt meter that battery is full power 4,2 volt dc.
So i try to push power button than my PDA doesn't start till now....
Atom Brick Solution...
suga_ngr said:
Hii...i was do to charge my PDA also iam test with volt meter that battery is full power 4,2 volt dc.
So i try to push power button than my PDA doesn't start till now....
Click to expand...
Click to collapse
Have you search on wiki?
I've been through that condition, last night actually when I pressed the wrong button (Power Button) when the MN1 bootloader looked for diskimg.nb0.
My device was near to death. I couldn't find the MN1 bootloader on my device's screen when I pressed the CAMERA+RESET(stylus). It remains dead until :
-I search the solution on http://wiki.xda-developers.com/index.php?pagename=ATOM_BRICK, I could see my device running its MN1 Bootloader
and looked for the ROM (diskimg.nb0) again and continued the ROM installation process
How to get the diskimg.nb0 please read this page :
http://wiki.xda-developers.com/index.php?pagename=ATOM_SDCARD
Maybe atom pure had the same step with atom exec when we try to solve the Brick Problem.
Cheers...
TOM PURE Dead
With my experience my atom was hardware broken.
somebody please tell me where i can buy atom hardware cause iam very love my atom...
try th!s tr!ck (cb ini mas)
yesterday 09 jan 10 it's happened same to me.
my case is downgrade from h3llow0rd1 6.1 to PD4v!et 19971 by m3dk!d.
then atom hang up.. dead! no screen, cann't boot or ON.. but still can charging
This tr!ck may be this could help u..
1. charging, look red lamp is on
2. then try replace battery, then put back on. it will blink (button call and end call will blinK)
3. with stylus try reset with pressing record button
4. if your lucky then it will show you boot loader screen
Now my atom is back again using Hell0w0rd R0M ... (^_^)
suga_ngr said:
With my experience my atom was hardware broken.
somebody please tell me where i can buy atom hardware cause iam very love my atom...
Click to expand...
Click to collapse
Entering BootLoader Mode:
1.Remove Battery
2.Press Camera button and hold it while insert the battery.
3.Press Reset with stylus (keep holding camera button)
If you're lucky, you'll be directed to bootloader mode.
try to push the power & camera button together while inserting the battery and then enter the bootloader mode camera+reset button.
My Atom Life (was) dead, too
..but only for awhile
this happened when I tried to flash this Bajok ROM.
I'm not new to flashing, but that kinda make me 'a little' careless this time.
I transferred the .dio file using active sync explorer while doing other stuff with my laptop.. soon after, I see that the file transfer is done, cause the window is closed. As usual, I do the rec button + reset ritual and flashed away..
I again continued my other works and got mesmerized in it for a moment or two.
Half an hour later I realized that my atom has been showing bootscreen for quite some time..
My first failed flash! Well, I thought, this is it...
Just to make sure, I pulled out the battery, put it back again and reboot.. still the same stuckness... Then, I figured that since this was caused by ROm flashing failure, why dont check the .dio file? So I did. I pulled out the memory card, put it in a card reader and explore it.. I notice that the .dio file is only 18 megs.. whatta..? The original .dio is like 70 megs, so it must had been transferred it incomplete.
So with high hope, I retrasferred the file, this time completely.
I inserted again the battery and repeated the rec button + reset ritual..
Boot loader appeared and flashed away like a charm!
Dear All
I have upgrade the atom with the atom rom WM6.5 21500. The rom was successfully upgraded but i don't like it. And when i tried to downgrade it to WM6.1, it didn't work. I have tried to enter bootloader but i can't, when the atom restart, they will not boot and restarting again and again. .
Please help in this matter..
thanks.
Qiky said:
Dear All
I have upgrade the atom with the atom rom WM6.5 21500. The rom was successfully upgraded but i don't like it. And when i tried to downgrade it to WM6.1, it didn't work. I have tried to enter bootloader but i can't, when the atom restart, they will not boot and restarting again and again. .
Please help in this matter..
thanks.
Click to expand...
Click to collapse
1. If your atom can goes into windows u can downgrade to 6.1 or 6.5 from my signature by using RUU from PDA viet.
2. If your atom can't goes into windows as well as boot loader, First you have to take out the battery for one or two minutes then put it back then try to enter boot loader again, if still not try the Second step by taking out the battery again then press and hold Reset + Camera button for one or two minutes then put battery back (keep pressing that button till u can see boot loader).
just want to add dolphin post
ur device is bricked, if and only if, ur device won't start normally... even if u press soft-reset, hard-reset, or even bootloader mode buttons. Before panicking, do da following:
Brick Test:
1. Make sure ur device has ample battery charge. If u're not sure plug it in with da wall charger for at least 10min
2. Remove ur battery for at least 1 minute
3. Replace ur battery while observing da LED lights
4. If da LED blinks once upon battery insertion, u might have hope yet
Da only way to upgrade on a semi-brick device, is to upgrade through bootloader mode. No bootloader mode, No upgrade possible - period.
Entering Bootloader Mode on Semi-Brick Atom:
1. Remove battery for for at least 1 minute
2. Press CAMERA+RESET(stylus) simultaneously
3. Insert battery while still holding da buttons
4. Release da buttons at da same time(u should see bootloader screen)
Note: Failure to hold the buttons at da same time during battery insertion will cause it not to work.
GOOD LUCK
dolphinxda said:
1. If your atom can goes into windows u can downgrade to 6.1 or 6.5 from my signature by using RUU from PDA viet.
2. If your atom can't goes into windows as well as boot loader, First you have to take out the battery for one or two minutes then put it back then try to enter boot loader again, if still not try the Second step by taking out the battery again then press and hold Reset + Camera button for one or two minutes then put battery back (keep pressing that button till u can see boot loader).
Click to expand...
Click to collapse
i follow all your step by step sugestion but it seems not working and i still cannot run into bootloader or switch to another O.S.
is there any other solutions you can give??
your help is very apprecciated.
knoxbrotherhood said:
ur device is bricked, if and only if, ur device won't start normally... even if u press soft-reset, hard-reset, or even bootloader mode buttons. Before panicking, do da following:
Brick Test:
1. Make sure ur device has ample battery charge. If u're not sure plug it in with da wall charger for at least 10min
2. Remove ur battery for at least 1 minute
3. Replace ur battery while observing da LED lights
4. If da LED blinks once upon battery insertion, u might have hope yet
Da only way to upgrade on a semi-brick device, is to upgrade through bootloader mode. No bootloader mode, No upgrade possible - period.
Entering Bootloader Mode on Semi-Brick Atom:
1. Remove battery for for at least 1 minute
2. Press CAMERA+RESET(stylus) simultaneously
3. Insert battery while still holding da buttons
4. Release da buttons at da same time(u should see bootloader screen)
Note: Failure to hold the buttons at da same time during battery insertion will cause it not to work.
GOOD LUCK
Click to expand...
Click to collapse
i follow all your step by step sugestion but it seems not working and i still cannot run into bootloader or switch to another O.S.
is there any other solutions you can give??
your help is very apprecciated.
dolphinxda said:
1. If your atom can goes into windows u can downgrade to 6.1 or 6.5 from my signature by using RUU from PDA viet.
2. If your atom can't goes into windows as well as boot loader, First you have to take out the battery for one or two minutes then put it back then try to enter boot loader again, if still not try the Second step by taking out the battery again then press and hold Reset + Camera button for one or two minutes then put battery back (keep pressing that button till u can see boot loader).
Click to expand...
Click to collapse
i follow all your step by step sugestion but it seems not working and i still cannot run into bootloader or switch to another O.S.
is there any other solutions you can give??
your help is very apprecciated.
This is my first post, so hy guys...... (i hope ive posted it on the wright location)
when i'm pressing the Turn on button it comes only the green "HTC" logo in the middle Without the system information in the left bottom i've to be onest im getting scared cause ive tried a lot of hard reset and nothing happens....
another problem is that i cant connect it at the pc because the connection by usb dont work.....what can i do?????
you're device is stuck just before flashing a rom (that happens when you perform task29 for instance)
Quote: "If you get a white screen with "hTC" in the middle then you need to take out your battery and enter bootloader mode manually before continuing (take battery out and put it back in, then hold the volume down button and briefly press the power button. Keep holding the volume down button until the bootloader screen appears)"
after that you can flash your device with any rom
Good Luck
get into bootloader mode and then flash a newer radio ROM. solved the problem for me.
p.s. read thoroughly about the correct radio for ur phone before flashing one
abuawab said:
you're device is stuck just before flashing a rom (that happens when you perform task29 for instance)
Quote: "If you get a white screen with "hTC" in the middle then you need to take out your battery and enter bootloader mode manually before continuing (take battery out and put it back in, then hold the volume down button and briefly press the power button. Keep holding the volume down button until the bootloader screen appears)"
after that you can flash your device with any rom
Good Luck
Click to expand...
Click to collapse
it work mate thank you a lot!!!
anytime