hi all, help me to back up my roms plzzzz
my ori rom is
Rom v 1.03 USA
n bootloader mode v 1.02
i wanna upgrade to wm2k3SE
but i cant back up my rom ?
if i wan to back up always pop up notice
Card initialize is failed ??
wat thats means ?
thzzz for ur anssss
While a lot has been written, the following should provide an easy-to-follow guide:
Preparation:
1. A torch (read on and you will know why)
2. 256M SD card
3. Download ntrw.exe, romupdate.exe, hexedfull.exe from the ftp of this forum to c:\ and install hex editor
4. Download the appropriate ROM file (hereafter referred to as "newrom.nb1"). Somehow, these rom files seemed to be deleted from this ftp. I will upload them later.
5. Cancel USB in ActiveSync
6. Use Sprite Backup to backup your ppc
Backup original ROM:
1. Put ppc into the boot loader mode (hold both on/off and camera buttons at the same time while resetting).
2. Insert empty SD card.
3. Connect ppc to pc through USB.
4. Run romupdate.exe on pc.
5. Select “\\.\WCEUSBSH001” in port settings. In the popup windows, enter “d2s” and press enter.
6. Don’t get panic to see the ppc screen goes dark. Use your torch and you will see the download percentage. Wait until it reaches 100% and shows “CheckSum is OK!”.
7. Insert SD card into card reader of the pc. Ignore the “format SD card” message and click “No”.
8. Run “command” to go into DOS prompt and change to root directory (cd c:\). Enter “ntrw read oldrom.nb1 s:” where s is the drive of your SD card.
9. Ignore the “Data error <cyclic redundancy check>” message. You should save another copy of this important rom file “oldrom.nb1”.
Change header of newrom.nb1:
1. Right click on oldrom.nb1 to open hex editor. Copy the first 220 bytes.
2. Open the downloaded newrom.nb1 file and overwrite the first 220 bytes with those of the old rom.
3. Save the edited newrom.nb1. You may save another copy of this important file.
4. Go to the command prompt and enter “ntrw write newrom.nb1 s:” to write it to the SD card. Ignore the error message “The parameter is incorrect”.
Update the ROM:
1. Insert SD card into ppc and put it to boot loader mode again (on/off + camera + reset). Use you torch to check the dark screen.
2. When it shows “Press Power to flash”, press the on/off button. Wait until it reaches 100% and ignore the message “Download Fail - CheckSum Fail”
3. Soft reset your ppc.
4. You may have to reinstall your software, unless you are familiar with the advanced features of Sprite Backup.
or u can find at http://forum.xda-developers.com/viewtopic.php?t=19500&highlight=rom+backup
thanks to talent and all XDA Dev
Phreakazoidz
Related
how would I go about upgrading my XDA ONE to the Latest OS, apparently you can do it, but im having trouble finding the files and the info on if it is actually possible!
any answers would be great!
thanks!
Rich
most people come to this forum asking the very same question you are if you use the search button and type in your questions you would have gotten the asnwer right away
http://lumpistefan.dyndns.org/
Ok here you go, its a little outdated but its what I still use:
Qman's how to use XDArit to write nk.nb1 or nk.nbf to your SD card aka the Bootloader Method!
1. Place XDArit and the nk.nb1 or nk.nbf file in the same folder and start XDArit.
2. Select your SD card (disk drive) from the drop down menu.
3. Select Write to SD
Notice that the Windows CE box is already checked so just click the browse button at the end of that window.
4. Select your (nk.nb1 or nk.nbf) image and then Open
Notice by default XDArit will open looking for a *.nb1 file but if you're going to use a .nbf file you'll have to manually change the "Files of Type" to *.nbf
Notice that nk.nbo / nk.nbo was automatically added as your boot-loader and its check box is unchecked so leave it that way and click OK. XDArit should start writing to the card.
When XDArit has finished writing the image put the SD-card into the XDA and hold the power button and soft reset. You'll be taken to the below screen:
SD DOWNLOAD
Card Type:
CE OS & BOOT
Press action to Download
Or
Press REC to Exit
Press action to download and it will start the download/restore from the SD card.
Follow the on screen instructions once its "Completed" which will consist of a "Soft Boot/Reset".
Click to expand...
Click to collapse
while i was updating my O2 XDA I to wm 2003 my computer freezed and my XDA had freezed on installing screen. Even I had reset my computer I still cannot open my XDA. There is an strange display on my XDA screen, also when I connect XDA to the cradle , my computer can see the XDA, but I cannot update my XDA as I can't reach to active sync
i would use the sdcard flashing it's the most stable way to upgrade xda1's
here is a guide
Ok here you go, its a little outdated but its what I still use:
Qman's how to use XDArit to write nk.nb1 or nk.nbf to your SD card aka the Bootloader Method!
1. Place XDArit and the nk.nb1 or nk.nbf file in the same folder and start XDArit.
2. Select your SD card (disk drive) from the drop down menu.
3. Select Write to SD
Notice that the Windows CE box is already checked so just click the browse button at the end of that window.
4. Select your (nk.nb1 or nk.nbf) image and then Open
Notice by default XDArit will open looking for a *.nb1 file but if you're going to use a .nbf file you'll have to manually change the "Files of Type" to *.nbf
Notice that nk.nbo / nk.nbo was automatically added as your boot-loader and its check box is unchecked so leave it that way and click OK. XDArit should start writing to the card.
When XDArit has finished writing the image put the SD-card into the XDA and hold the power button and soft reset. You'll be taken to the below screen:
SD DOWNLOAD
Card Type:
CE OS & BOOT
Press action to Download
Or
Press REC to Exit
Press action to download and it will start the download/restore from the SD card.
Follow the on screen instructions once its "Completed" which will consist of a "Soft Boot/Reset".
Click to expand...
Click to collapse
THIS THE FRIST TIME IN THIS SITE AND I FOUND IT IS MORE HELPFULL
FOR DEALING WITH POCKET PC
SO FOR HELP IF ANY ONE GET ME SHORT STEPS FOR UPDATING ANY POCKET PC AND FOR KNOWLDGE HOW TO UNLOCK POCKET 1010 & 2020
AND SPV E200 OR OTHER MODLES OF SPV AND IF THERE IS TOOL TO UNLOCK BLACK BERRY 7230
BE THX FOR ANY HELP OR REPLAY
B.R
ROBISH
Upgrade
QUOTE
Ok here you go, its a little outdated but its what I still use:
Qman's how to use XDArit to write nk.nb1 or nk.nbf to your SD card aka the Bootloader Method!
1. Place XDArit and the nk.nb1 or nk.nbf file in the same folder and start XDArit.
2. Select your SD card (disk drive) from the drop down menu.
3. Select Write to SD
Notice that the Windows CE box is already checked so just click the browse button at the end of that window.
4. Select your (nk.nb1 or nk.nbf) image and then Open
Notice by default XDArit will open looking for a *.nb1 file but if you're going to use a .nbf file you'll have to manually change the "Files of Type" to *.nbf
Notice that nk.nbo / nk.nbo was automatically added as your boot-loader and its check box is unchecked so leave it that way and click OK. XDArit should start writing to the card.
When XDArit has finished writing the image put the SD-card into the XDA and hold the power button and soft reset. You'll be taken to the below screen:
SD DOWNLOAD
Card Type:
CE OS & BOOT
Press action to Download
Or
Press REC to Exit
Press action to download and it will start the download/restore from the SD card.
Follow the on screen instructions once its "Completed" which will consist of a "Soft Boot/Reset".
This is from rudegar.
Another way is to goto lumpistephans ROM kitchen cook yourself a ROM and upgrade. I did it with 2003 and it works fine.
Good luck,
Robert
1. Download the 20060426 from www.seeo2.com
2. Run DSUU, after extracting the files in directory windows\temp DO NOT CLICK NEXT
3. Copy all 6 files into temporary or another directory
4. From that 6 files, copy 2 files with the extention nb0 (diskimage_ver.nb0 and eboot.nb0) to your mini SD
5. After copying into your mini SD, rename diskimage_ver.nb0 into diskimg.nb0
6. Now, you can run bootloader by pressing camera and soft reset ( you have to put your mini SD into your Atom so that the bootloader will boot from mini SD
7. Just wait and if there is some error message do not bother them, the most important that downloading OS Image and Eboot
8. After that your screen will blank, do not worry or panic
9. Pull out your mini SD and connect USB to PC and run bootloader again
( please make sure that your usb already connected to pc )
10. Now u can normally run the 20060426
This topic has been posted in many threads, there is no need to use the SD if this procedure is not done correctly you will loose the bootloader all together. Instead use the method posted by Luchao:
1.run atom 0416 rom update program, after the DSUU program extracted the files, don't click "next", go to windows/temp folder, copy those files extracted, except "diskimage_Ver.nb0" and "ExtendedRom.img", then save them somewhere else.
2.run july exec rom update program, after the DSUU program extract the files, don't click "next," go to windows/temp folder, overwrite with the files you just saved, this will leave only the diskimage_Ver.nb0 & ExtendedRom.img files as of the july exec rom, others become atom rom files, including an older bootloader which allows you to flash back other roms.
3. flash
http://forum.xda-developers.com/viewtopic.php?t=52925&postdays=0&postorder=asc&start=150
i just saw eboot.nbo & test.zip file in windows/temp/ folder, how to get the others file ? Thanks.
activesync mode not working
i tried the activesync mode, but not working.
finally i used bootloader method. just copied eboot.nb0 file to your miniSD. and enter bootloader mode.
Re: activesync mode not working
klikman said:
i tried the activesync mode, but not working.
finally i used bootloader method. just copied eboot.nb0 file to your miniSD. and enter bootloader mode.
Click to expand...
Click to collapse
bro, just klik next one more time, and DSUU will extract the others files
tjs0509, I tried your sd card method and totally lost the bootloader when I tried camera and soft reset. Is there anyway to bring back the bootloader?
interesting methods...
thanks!
"Camera" + SR, connect USB, run Device Software Update Utility, flash...
dear
tjs0509
I Downloaded the 20060426 from www.seeo2.com
2. Run DSUU, after extracted the files in directory windows\temp DO NOT CLICK NEXT
3. I Copied all 6 files into temporary or another directory
4. copied 2 files with the extention nb0 (diskimage_ver.nb0 and eboot.nb0) to your mini SD
5. After copying into your mini SD, renamed diskimage_ver.nb0 into diskimg.nb0
6. Now, I maked bootloader by pressing camera and soft reset ( I had to put my mini SD into your Atom so that the bootloader boot from mini SD
(from 1 to 100 dowloded)
7. I seem and if there is some error message do not bother them, the most important that downloading OS Image and Eboot
8. After that My screen was blank,
9. I Pulled out my mini SD and connect USB my pc . After I waited since 2 hour .screen been Black.. black... Black..I tried soft reset .and batery out -in but not anythink .
I was worring .!!??
Can help me What can I do?
Homer285, any help. I really lost the bootloader in the SD card method. I tried to connect USB and the 0721 ATOM EXEC recognize the ATOM, but when downloading the ROM, the ATOM just rebooted. I cannot press camera and reset to go to bootloader mode. Is bootloader mode be activated by a program in SD card so that it can be run in the explorer. Please help.
tjs0509 said:
1. Download the 20060426 from www.seeo2.com
2. Run DSUU, after extracting the files in directory windows\temp DO NOT CLICK NEXT
3. Copy all 6 files into temporary or another directory
4. From that 6 files, copy 2 files with the extention nb0 (diskimage_ver.nb0 and eboot.nb0) to your mini SD
5. After copying into your mini SD, rename diskimage_ver.nb0 into diskimg.nb0
6. Now, you can run bootloader by pressing camera and soft reset ( you have to put your mini SD into your Atom so that the bootloader will boot from mini SD
7. Just wait and if there is some error message do not bother them, the most important that downloading OS Image and Eboot
8. After that your screen will blank, do not worry or panic
9. Pull out your mini SD and connect USB to PC and run bootloader again
( please make sure that your usb already connected to pc )
10. Now u can normally run the 20060426
Click to expand...
Click to collapse
this method broke my bootloader too. i spent about RM200 to repair my bootloader...grrr
How can I flash my coby kyros mid1125? It's got a weird screen display and is permanent. It covers three quarters of the screen when its switched on. I have tried quick img program but it keeps asking for fast boot mode. I have tried holding the volume up and down buttons but it doesnt work. also have several times done reset. I have also tried FWDN program but it gives an error. I have the .img file. Can someone point me in the right direction please. Tell me what to do and provide download links for working .img file flashing uploaders etc.
Thank you.
ukguy183 said:
How can I flash my coby kyros mid1125? It's got a weird screen display and is permanent. It covers three quarters of the screen when its switched on. I have tried quick img program but it keeps asking for fast boot mode. I have tried holding the volume up and down buttons but it doesnt work. also have several times done reset. I have also tried FWDN program but it gives an error. I have the .img file. Can someone point me in the right direction please. Tell me what to do and provide download links for working .img file flashing uploaders etc.
Thank you.
Click to expand...
Click to collapse
Download from this link ,
https://www.dropbox.com/s/fixhl34x7qr13v6/1125.zip?dl=0
Copy entire 1125.zip folder to desktop
Extract 1125.zip to desktop
Install PdaNetA4170.exe driver ( This should allow you to transfer files with Fastboot )
This is Version 4.17 installer for Windows 8/7/Vista/XP (both 32/64bit)
Extract CWM recovery img_1125 folder to desktop by itself ( Do not remove any files from this folder )
Move zip files from zips folder to micro sd card and insert sd into tablet ( leave these in zip format !! )
coby_gapps.zip
coby_mid1125-seed-0012.zip
Superuser-3.1.3-arm-signed.zip
Also move apks from apks folder to MicroSD card
Uni-init+v1.0.apk
Google_Play_serv.ices-signe.d .apk
Busybox.apk
Link2sd.apk
and
market-helper-2.0-beta.apk ( this will allow spoofing of market for not compatible apps )
Open cmd window
( menu , run , when window opens , enter “cmd” without quotes )
Cd to directory
ie ,
type in window
cd desktop , ( enter )
cd CWM recovery img_1125 ( enter )
Now place 1125 into fastboot mode , power ( or reset button ) and volume down , tablet will show fastboot mode in lower left corner
Plug in usb cable to pc and tablet
Then in cmd prompt type
fastboot boot recovery.img ( enter )
It will show some stuff , flash ok and done ok
Tablet should boot to CWM give it a moment to do so ( You will see CWM Recovery Top hat and such )
Volume up is up , Volume down is down , Home ( Silver Button ) is select
Go to and select flash zip from sd card
This will pull up menu of following zip files
Flash each zip file
coby_mid1125-seed-0012.zip
coby_gapps.zip
Superuser-3.1.3-arm-signed.zip
Select reboot
Tablet will boot ,again give it a moment ( You will see Coby and then Android splash screen )
Select language from first screen ( as it will be in Dutch ), finish setup of tablet
Open ES File Explorer , go to tools setting in ES File Explorer and select
“Root Explorer” to on , allow when Super User prompt shows , this will prove SU is installed and working
Open ES File Explorer , Select sdcard top right , Select storage
Install Google_Play_serv.ices-signe.d .apk ( To sync Play Store )
Install Busybox.apk
Install Link2sd.apk
Install Uni-init+v1.0.apk
Open Uni-init+v1.0.apk , install intd support
( you will need busybox installed first for this to work )
You now have working Play Store , Superuser and Android 4.1 with Intd support
For Extended memory ,( You need this )
Increase Internal Memory by Link2SD : Min 2 GB microSD
In order to add memory to Coby 1125, your micro SD card used for install will need to be formatted
Copy all files you wish to keep from micro SD to desktop as it will be wiped
• Backup all your files on memory card.
• Go into the Recovery Mode ( as above , fastboot boot recovery.img ) ( Your operating system will be fine )
• Make a nandroid backup at this time
• Select “Advanced”, and then choose “Partition SD Card”.
• Then Choose your size ( if you have a 2GB Memory Card, choose 512 MB, and if you have a 4 GB Memory card, you can choose 1024 MB, ext ).
• Select 0 Swap.
• Wait for the process to finish, and then select Reboot
You’ve just made a partition on your memory card, and its ready to use.
Now follow the steps below for Link2SD
• Open Link2SD. You will be prompted to choose between ext2,ext3,ext4 and FAT32.
• Choose ext2
• Select OK ,
• It will then say, “Mount Script Created”.
• Now you Reboot your Tablet
• Open Link2SD again, if any message does not appear ,it means you succeeded.
• Go to Link2SD > Setting( far right top icon ) scroll down > Check the autolink. (to automatically move apps upon installation).
If you already have some apps listed , select “create link” ( be sure to check the files: app, dalvic-cache, and library files).
Move to SD option only moves app to SD it does not link them
Now to check the memory, select “Storage Info” . this will be showing you up the current status of your internal memory.
You should see as below SD Card 2nd Part
To move a system App you can long press App , it will pull up menu , select convert to user App let it do its thing
Select App again and it will open option to create link as installed user apps do
So far I have moved Calculator , VPN , Music FX , ES File Explorer and Sound Recorder with no issue
Use Link2Sd and (long press) on SystemUpdate.apk ( /system/app/SystemUpdate.apk ) and freeze app.
This will stop System Update from happening at random moments or on reboot
There is no Update to install though the System thinks so (without freezing it will continue to show updates available)