I can't keep a signal connection with my SX 56 on Cingular. I soft boot and I can send and receive calls but after a while I have no signal and It won't work it again until I soft boot.
I tried running the band switching tool but when I start it it just says ERROR under "current" and does noyjing else.
Starts are
ROM: A.30.09 ENG - 01/01/04
Radio Version: 6.24.00
Protocol 324e4
HELP!
TIA!
Mike
i have exactly the same problem. i have been searching google, i couldn't find any solutions.
the only thing that you can do is to turn off the phone and turn it back on, (click on the signal icon to turn it off) that case you don't need to soft boot it everytime.
if you found a better solution, please tell me.
thanks
good luck
:wink:
before updating I have same problem, but now everything is ok and it's connecting by itself
ROM: 3.04.00 ENG (WM2K3SE)
Radio: 6.25
how do we obtain a WM2K3SE version?
where did you get that OS?
thanks
if you do'nt need surfweb via gprg just ask your operator to turn it off.
that's all
Related
I have a Qtek 1010 64 MB:
ROM version 3.16.13 ENG
Radio version 3.19.01
Protocol version 32S54
I'm having the following problems with the phone:
1. Sometimes the device "hangs" when I'm making a call. It freezes completely, forcing me to perform a soft reset.
2. When I'm trying to call a phone that's busy, I don't get a busy signal. Instead, the connection is just dropped.
3. Sometimes my phone is unable to receive calls even though it shows a full strength signal. This also happens when I'm in areas where I know that the signal actually is very strong.
4. When I return from an area with no signal (eg my local supermarked which is in a basement), the phone does not regain the signal without a reset.
I've searched the forums and seen that other poeple have experienced similar problems, but I've not found any solutions. Does anyone know how to fix these problems? Would an upgrade of the radio stack solve any of them?
Try to update your phone bios.
The latest radio version is 4.21.00 and rom version 3.17.03
or try to install xda spec. edit. 1.2
Do you know that an upgrade will fix any of the problems? Or should I just try it and see what happens?
Hello all.
I can't get a stable phone signal in my QTEK 2020.
I installed WM2003SE 2.06 and I try'd radio 1.18, 1.14 and 1.08.
The 1.18 is the worst for me, the outhers work great in the first Hard reset.
When I first Hard Reset my phone, after the update of rom I get good and stable signal, but when I start installing some stuff on it, the signal becomes instable, and the worst is that if i'm on a low signal area and if I lose signal I have to soft reset the QTEK or enter flight mode and then turn it of to get signal back.
Anyone had this problem too?
I searched this forum and found some posts about this, but no solutions.
If anyone has any solution, please help me with this.
Thanks
first of all after hard reset , you said your phone signal is stable so it should be from the software you install later on. Try to test each software which one made your phone signal bad.
In some case the radio rom is the problem for me the best is 1.12 . I have tried 1.18 1.14 but I got unstable signal so I decide to use 1.12 instead. Another way to solve unstable signal is , the setting in phone option to use manual network instead of automatic and uncheck all the network that it is not your phone service provider network.
Thanks for your help.
I made all the ajustments that you told me, and the bigest diference that I notice is that when I lose signal, I recover it much faster than before, but the signal is still week.
Can you tell me where to get radio 1.12, I never seen it for download and I like to test it too.
Thanks again.
check your email
radio 1.12
I also have signal problems. lots of breaks
Can you please, also send me the 1.12?
Thanks
Thanks for the file.
I will test and then I post the result.
I've just upload radio1.12 rom to the FTP server . Get it there
(in himalaya folder)
I have also problems with my signal stability.
Can I also have the 1.12 radio version
I've tested all versions except the 1.12.
After testing the 1.12 radio, my problem is the same.
I Reinstalled the 1.72 Rom with radio 1.14 and it's a little better, the only problem is that now I have WM2003, not the SE.
I have siemens SX56 I was on AT&T. I unlocked it signed up for CIngular. Phone works fine cant get on internet. Cingular is 850/1900. When go to GSM band program it says error. I did the hold down button and soft reset to toggle it to 1900 but it wont take it. It is stuck 0n 900. I am ROM 3.17.03
ROM DATE 05/15/03
RADIO VERSION A.33.02
PROTOCOL VERSION 1.3.3
PW10A1
Is this why I cant get on internet? Can someone help me out? Am I stuck with a phone that wont get on the Cingular internet? Thanks
I am a dumb blonde trying real hard to get this thing going and I am slowing losing my mind!
I recently loaded the xda developers ver. 1.2 rom to unlock the sim, seemed to work but later found that the phone was not functioning after 5 mins., a soft reset gets it going again, but then stops again after a few mins. This has happened to all three phones I used this program on. Can anyone help me fix this? PLEASE HELP!!!!! Contact me at [email protected]
What do you mean with "not functioning"?
Have you installed additonal software or just the ROM 1.2 ?
Stefan
By not functioning, I mean that no calls or text messages are received or sent after a few minutes of sitting. I have not installed any other software with it.
did you install a radiostack along with the rom if so
and you did a 900/1800 radiostack on a 900/1900 device
or the other way around you should reflash the right radio stack
if not you can try choosing the right band in the bootloader
I did not change the radio stack, the rom 3.17.00, radio version 6.12 . I have set to 1900 with bootloader, still same problem. FIDO in Vancouver, canada. got any suggestions? the sticker says its a pw10b1
Hey,
I was given a Softbank X01HT from my brother and I've been using the information on this site to try and get the phone up and working on the Three network in Australia. This site has been really informative and I managed to do a lot of upgrades to my phone and everything works fine except that I get "no service" when I put my Three sim card into the phone. Could someone please help me work out what's wrong with my phone?
Here are the details of my phone:
Device: Softbank X01HT (Black one don't know how old)
IPL-1.04
SPL-2.10.Olipro
ROM Version: CRCs r13.3
Radio Version: 1.47.30.19
I've done the following:
Upgrade to hard SPL (first thing I did)
Run the Hermes_SIM_CID_Unlock_v3a (Though now I have doubts that I did it right)
Installed various rom (mostly for fun)
Installed Josh V15 Manila 2D rom
Installed the dopod AUS 3network WM6 (I thought it would have the right radio and settings)
Installed the CRC rom (I didn't like the dopod rom)
Any help would be appreciated. I've been searching but I couldn't find a good answer.
I'm not very familiar with that phone but you'll need to create a new data connection so that it can connect to 3.
When creating one, make sure you select the data connection type as GPRS, 3G etc, the access point is called 3services, no username or password is required. Should be good from then on.
These forums are awesome, with a bit more patience and perserverance I finally got my phone to work.
I did more searching on the X01HT and found that people were using the radio rom from pof's SIM & CID Unlocker. There was talk about cooking roms and stuff which I didn't want to try, so I decided to just run through the unlocker again. I made sure that I turned off my phone for 10 secs at the end and do a soft reset after the 10 secs, as I was a bit careless with that part last time.
After getting through all the steps, the phone recognised my sim and configured my phone for the three network. I can now connect to the net and make phone calls.
Now the details of my phone are:
HERM200
IPL-1.01
HERM200
SPL-1.40.Olipro
ROM version: CRC r13.3
Radio version: 1.16.00.00
Thanks guys for running this site. I reckon i'll be on these forums a lot in the next few months. There's still a lot of tweaks I want to do to my phone.
Mate, bit of advice, install Hard SPL V7 so there are no "accidents" when flashing a new rom... Its a bit better at protecting your Hermes when you flash than 1.40. Thats an older version of Hard SPL.
Cheers...