Related
Hello all,
My XDA 1 has a fault I don't understand. When I hit the Power on button it comes on and stops at the O2 splash screen. It will not go beyond this point no matter what I try. The desktop does not recognise the device when I connect via USB. I have tried:
1. Soft reset
2. Hard reset
3. booting up in bootloader and running all device tests (failed USB rx & Infrared rx)
4. In bootloader copying boot to SD and booting with that. (Unfortunately I do not currently have an SD card large enough to copy CE or GSM boot)
What I really need to know is if I can try to upgrade the device (to WM2003) anyway and if the upgrade will solve the problem I have now.
DEVICE DETAILS:
Device: O2 xda 1
Bootloader: 5.14
ROM: 4.01
Radio: 3.02
Any and all advice/help/replies most welcome. Sorry if this has been answered previously but I searched and couldn't find the info I needed.
Thanks,
Aide
It's a lost cause...
Device can't connect to activesync via serial or USB so I can't upgrade and see if that solves it. Don't have card reader to try SD method. The problem is as described in my first post above.
I don't know how this happened (I hadn't tried upgrading or any sort of flashing apart from unlocking the device a looooong time ago).
Any ideas as to a solution would be greatly appreciated.
Aide
Your ROM version is not known (at least for me ) ... are you sure it's not 4.01.00 ??
Anyway, regardless of the reason, the good news is that you still have the boot loader working, the bad new is that you MUST use the SD method since the ActiveSync doesn't recognize the device.
Thanks Bis,
Yes ROM is 4.01.00 (sorry if I confused anyone ). Problem is at a new level.
I got an XDA with a cracked screen (so it's almost impossible to use though everything works) and used that with XDAtools (thanks Jeff) to upgrade to xda-dev Special Rom 1.2.
I copied the ROM to the 32MB SD card (got and error message at the end) but still risked using it to try bootloader method on the 'hanging xda. It worked: kinda :?
It now boots and hangs at the xda-dev splash screen and no other changes to original problem. Was that error message I saw responsible or could something hardware related have happened?
Still waiting for relief...Help me please. Someone, anyone...
Aide
aicon said:
I copied the ROM to the 32MB SD card (got and error message at the end) but still risked using it to try bootloader method on the 'hanging xda. It worked: kinda :?
Click to expand...
Click to collapse
That's your problem - redo everything above - but using a 64MB SD Card or higher. The ROM files are just over 32MB. Even if your card said it was all there chances are it could have been corrupt.
-JB
Thanks JB,
Getting 128MB card in the morning, will let all know how it went.
Aide
PS: Noticed someone posted same initial problem under topic 'XDA 1 locked on O2 screen' in General forum with no solution posted. So if anyone is interested - watch this space!
Ahhhh... God is in his heaven and all is right with the world
Used 128MB card and it worked like a charm. One thing I noted though: After I used XDAtools to copy ROM to the SD card and put it in the device it would not boot from the card automatically. I assume the ROM update tool on the device checks to see if the current ROM and the one on the SD card are the same and ignores the SD card if they are. (By the way, could someone please confirm if this is so? Idle curiosity :wink: )
I had to use the tool on the device to write the ROM to SD from one device and then the other device (that had the hanging problem) finally read that copy.
Thanks all,
Aide
some boot loder versions doesn't recognize ROM file on SD cards ... ex: 5.22
hi ppl,
today I ve made rom with the romkitchen, it was 2003 final and everything went ok, phone was functional until I used to try to install some newer versin of the programs I previously included in the rom. That didnt work (of course) so I decide to put another rom without those programs so I can install newer versions but when I run the romkithen exe computer report
in the dos window
error getconnectiontipe - unspecified error
error getting connectiontype
and the program for the patching report that he is trying to get the data from the device and after that he reports that
"cannot execute the remote communication program, please make sure that the usb/serial cable is properly connectes"
of course cable is connected, device syncing with the active sync and the icon is green, used to try to soft reset pc and pocketpc, to hardware reset pocket pc, to connect it to other pc and patch there, to install active sync 3.7.1, to reinstall active sync 4.2, to reinstall usb drivers on the pc, to put sim card and sd card out and to patch then... nothing helped...
what can I do ? is that due to the windows 2003 instalation on the pocket pc (had same version on other wallaby without the problems) ? can I solve that some way ?
I ve read before that patching can be performed from the SD card so I found the xda tools and osi image tool but couldnt found rom nd1 file anywhere (was stupid and didnt make copy of my previous rom)... which rom can I use just to enable USB connection and after that I ll patch it with the "normal" rom from the rom kitchen...
Ive checked those roms http://wiki.xda-developers.com/index.php?pagename=ROMVersions but didnt find any nd1 file in the files I ve checked, can I use those roms with osi image tool eventually ?
which one ?
Lots of questions ... Sorry people ...
I can use it in this condition too but I d rather have an opportunity to flash it to some other version maybe.
Best regards to the community !
I think it´s just the problem that the ROM prohibits flashing via EXE-file. You have to flash via SD-Card.....
You find the ROm to write on the SD-Card in the EXE-FIle. Just extract the exe using winzip, and then you will find it in a subdirectory (normally english, or dependent on the ROM-Language...)
Stefan
Thanks a lot Stefan, so I can use some ROM from the page http://wiki.xda-developers.com/index.php?pagename=ROMVersions ?
Any advice which one should I take please (Im not using any of the operators noted there, just looking for some rom that will function ok) ?
Thanks m8 !
Yes, you can take any rom of it. Mostly the T-Mobile prohibits flashing via EXE-File, but Flashing via SD-Card is more secure in my opinion. So i´ve done 99,9% of my flashes via SD-Card, and you can believe me, i´ve done it a lot of times.....
By the way, which software has to been updated in my romkitchen?
If you give me the hints, i could try to update them....
Stefan
thanks a lot for your time and advices Stefan !
Its not a huge problem but probably we share same opinion - most of the tech guys like to see that everything work fine, if something doesnt work then we re not satisfied.
Basically problem is that I included spb pocket plus in the rom and therefore I cant install spb weather which demands pocket plus v 2.5+ and version in the rom is 2.0. I cant upgrade it coz its in the ROM, used to try to remove it from the registry but no luck, used to install latest spb diary coz the spb weather also work with the diary but looks like that the first thing weather perform is checking of the pocket plus version and if the version is not 2.5+ it stops the installation...
Probably for the most of the people spb weather is not a reason for loosing couple of hours in trying to change rom in wallaby but as I ve mentioned I like the things that work 100%, if some electronic/computer stuff work at 99% that usually bother me. Stupid - I know but thats the way it is.
Im going to patch it thru the SD, thanks again for the all your efforts now and before.
GL & HF !
Sorry...
Still need help, using the OSI tool I copyed NK.nbf file from 4.02.04_eng rom to "XDA SD Card Slot -unknown size" - coz I dont have card reader/writer at the present moment so I tought that I can put the file via the cradle connection while the card is in the wallaby...
Checked the card from the wallaby file explorer but nothing is on the card, since I had expirience with direct writing to c64 and amiga disks writing I assumed that file could be written directly to the card without OS instructions but after the reset of the wallaby it report that card shoud be formatted to become writable... Is that normal, or I should wait for the card writer reader to put the file properly to the sd card ?
If possible please help me with the link for the OSI tool patching, I cant find it anymore, checked thru the site but no luck, dont know what I have to press so the wallaby read the rom from the sd card.
Thanks Stefan & all others
success !
No help needed, I ve made it...
So dont have any fears as Stefan told unpack the rom from the self extracting archive and run osi tool, in the source field set nbf as a file type and then select extraced rom.
As a target you can set card reader/writer and also you can put the SD card in the wallaby as I did. Set the XDA SD card as a target in that case.
Its normal that after the writing (no message that writing is successfull, when it is finished OSI tool will stop) SD card become unreadable to wallaby.
Then perform actions as noted in SD card patching info
http://wiki.xda-developers.com/index.php?pagename=Wallaby_HT_FlashSD
Hold the power button and soft reset. You'll be taken to the below screen:
SD DOWNLOAD
Card Type:
CE OS & BOOT
Press action to Download
Or
Press REC to Exit
Press action to download and it will start the download/restore from the SD card.
Follow the on screen instructions once its "Completed" which will consist of a " Hard Reset"
Action button mentioned above is middle button - "D PAD"
Works like a charm, now I have o2 win 2002 and later I ll patch it to 2003 SE again but without pocket plus.
Thanks Stefan and community !
ok my phone is HTC 8525, with WM 6.1 professional . It worked fine for 3 days then it start freezing , before it does that a blue background will appeare ,then it will not let me do anything at all . When I try to touch an icon, it will say something like invalid location or could not find target . I have to hard reset it. sometimes I have to reset it 4 or 5 times a day . , In addition, the mini card will freeze the whole phone is there is a solution like reinstall the whole thing ? please help me I truly appricat it . In addition, the mini card will freeze the whole phone is there is a solution like reinstall the whole thing ?
Hmmm, "the mini card will freeze the whole phone"??? Are you referring to the SD Storage Card? Do you have any volatile data stored on the card? Any Today Screen Applications?
If this is the case, try shutting off the phone and removing the card. Then place the card into a card reader, and plug it into your PC. Make a folder on the desktop of your PC, and COPY all the contents of the SD card to the folder.
Now, reformat the SD card in your PC, as FAT32, and default for all characteristics.
Once reformatted, copy all that stuff back onto the SD card from the temp folder on your desktop, making sure everything is returned to it's original locations. Pop the SD card back into your phone and see if it's fixed. Sometimes, corrupted space on the SD card will make the phone behave very badly. Hopefully, this procedure might fix it for you.
-pvs
Yes Sir, i apaologize , i was refering to the SD card . i am just tierd resetting the phone every 4 hrs . do you recomend any shops that can fix the soft -ware . i notices when i start the phone and i go to clean tmp it will say" 8 Fils and 4 folders of 656 Bytes cleard ! . then 5 hrs later the blue screen comes back
After doing what pvs said, and if you still have problems I'd check for bad blocks with MTTY... I would also ,after confirming no bad blocks, would flash a stock rom then reflash wm 6.1 and see if that helps... Cheers...
Wow , how to do all that if you dont mind me asking , actually i took the SD card out i am not in need for it at the moment . can you please help me to do what you said and i truly appreciat it , Great thanks for both of you gents
pvs already says what to do in his previous post...
To check for bad blocks follow this : http://forum.xda-developers.com/showthread.php?t=377389
To Flash a stock rom you need to know what carrier the phone was on. Download the wm6 update from their site and, Making sure you have Hard SPLed your phone, I suggest flashing via the sd card method. Its safer than flashing through pc.
Format sd card fat32. copy .nbh file of the stock rom (you may have to search for it) onto the sd card and rename to "hermimg.nbh". Put back in hermes and reset to bootloader (power button, OK button above flywheel and soft reset with stylus. Hold all buttons until it goes to tri-colour screen). It should recognise the os flash and load up a screen showing 1st boot screen, 2nd boot screen, gsm And os (or something like that as cooked roms don't generally have the gsm part). MAKE SURE YOU HAVE AT LEAST 50% BATTERY!!!!! Follow the prompts... I generally use the sd card method to flash ALL my roms so I don't have problems like usb disconnecting or pc rebooting/hanging or power failures.
Hope this helps you out, Cheers...
BASELABBAS ... Please describe what you are doing when you say that you are "HARD-RESETTING" several times a day. Are you:
1) poking the stylus into the hole at the base of the unit?
- or -
2) holding down the two soft-keys WHILE poking the stylus into the hole until the confirmation screen appears, and then opening the keyboard and typing 'R' and then [SPACEBAR]?
If you are doing the first ... this is called a SOFT reset. The second is a HARD-RESET, and will wipe the phone clean of ANYTHING outside of what came with the ROM itself.
Since you have posted that you already removed the SD Card from the device, and can (for the time-being) live without it, I recommend you do an ACTUAL Hard Reset (backup anything you need to keep first) via step #2 above, and then be patient about installing any apps. I wouldn't do anything more than sync it up via ActiveSync with your contacts for the first few of days. If things start to go crazy without any third-party apps installed, then I would look into the steps that ultramag69 has suggested ... starting with a flash to a stock ROM.
WM6.1 has been a bit shaky on our Hermes thus far. Some people are getting good results, but a lot of others are having issues like you are describing. I would suspect that your ROM might not be a good match, before I'd suspect bad blocks at this point (and it's a bit easier to test for).
If the stock rom does better on your device, you can try flashing back up to a WM6.1 ROM after that. And if you haven't already, make sure that you have installed HARDSPL before doing any of this stuff.
Good luck,
-pvs
Mr. pvs , I am doing the #2 holding down the two soft-keys WHILE poking the stylus into the hole until the confirmation screen appears, and then opening the keyboard and typing 'R' and then [SPACEBAR]. I tried to download Hard-SPL 1[1].10, when I open it on my PC it will give me instructions then when I press upgrade I will see 4 color screen the Sync icon will disappear and then it will say that it lost connections.
it looks like i need to update
this what is say
From :
Image Version : TNT.19199
to
image version 2.05.255.1
BASELABBAS said:
Mr. pvs , I am doing the #2 holding down the two soft-keys WHILE poking the stylus into the hole until the confirmation screen appears, and then opening the keyboard and typing 'R' and then [SPACEBAR].
Click to expand...
Click to collapse
OK, well that's definitely a Hard Reset. So your WM6.1 Rom is acting flaky right aftwerwards, eh? I would say it's time to try a different ROM, as we've been discussing above.
BASELABBAS said:
I tried to download Hard-SPL 1[1].10, when I open it on my PC it will give me instructions then when I press upgrade I will see 4 color screen the Sync icon will disappear and then it will say that it lost connections.
Click to expand...
Click to collapse
No ... try Hard-SPL-V7.zip found at the bottom of THIS PAGE. I THINK you can flash it via the SD method if ActiveSync isn't working for you (if not, somebody please correct me). To do this, open the downloaded ZipFile with WinZip or WinRAR and copy the file inside named RUU_signed.nbh to your desktop. Rename it HERMIMG.NBH, and copy it to the root of your freshly reformatted (FAT32) Storage Card. Put the Storage Card into your device and press the side OK button and the power button simultaneously while resetting with the stylus until the tri-color screen appears and turns white. The device will find the HERMIMG.NBH file and offer to upgrade by pressing the Power Key. This will install HardSPL onto your device without the need for ActiveSync. You can also flash ROMs in this manner.
Again, good luck,
-pvs
No, You need to run a file from the phone itself to install hard SPLvia sd card. You can find it on page 116 of the hard SPL or how not to brick your hermes thread.
Cheers...
ultramag69 said:
No, You need to run a file from the phone itself to install hard SPLvia sd card. You can find it on page 116 of the hard SPL or how not to brick your hermes thread.
Cheers...
Click to expand...
Click to collapse
Thanks for checking me on that, Ultramag. I had a feeling there was something I was forgetting.
-pvs
I've just finished successfully flashing an unofficial WM6.1 ROM to my StarTrek (Cingular 3125) using only a microSD card (no data cable, no ActiveSync, no Windows) and the brilliant work found on this forum. I thought I would share the details of my success in the hopes that it will help the next person who stops by, since I myself found it difficult to find a definitive yes/no on the matter here.
Requirements:
HTC StarTrek
I had the Cingular ROM; Any should work.
microSD card
IMPORTANT: Your card MUST be using FAT32 for this to work. If it is not already so, back up its data and do this now. (Windows will show a FAT16 volume simply as "FAT".)
AppUnlock tool
The one linked at this post is good. http://forum.xda-developers.com/showpost.php?p=1146363
The ROM you wish to flash
I used the WM6.1 Standard ROM posted here by Erofich, since it is most appropriate for a Smartphone such as the StarTrek. You can also use the Professional version, though it is intended for use with a touch screen, so you will have to control a cursor with physical keys.
A computer you can use to extract and place these files onto the microSD card.
After you've obtained the listed files and have them extracted somewhere on your computer, copy the following files to your microSD:
SurrealNetworksAppUnlock.cab (Anywhere)
The entire SSPL directory from your extracted ROM download. (Anywhere)
RUU_signed.nbh, found within the RUU directory of your ROM download. (Rename this to STARIMG.NBH and place it in the top-most level of your microSD card, not inside a folder.)
Insert the microSD into the device (the door is located beneath the SIM card). Using the File Explorer (or Total Commander, if you have it), move or copy the three contents of the SSPL directory from your Storage Card to the top level (/) of your phone.
Find the SurrealNetworksAppUnlock.cab file on the Storage Card and run it. It should install like any other application, and you will notice a change to your Home Screen wallpaper.
Using File Explorer again, navigate to the top level (/) of your phone and run SPL.lnk (36 bytes, if this helps you distinguish which file to select). If all goes as expected, you will see a white screen, followed by a message telling you to press the top Volume button to proceed. Do this, and it will flash your new OS to the phone.
I hope I've offered a clear and helpful explanation of this process. Enjoy your now-renascent StarTrek!
Special thanks to Corian for helping me troubleshoot, to #xda-devs, and to all content authors involved here.
Funny, I was planning on re-flashing my 3125 via SD card, but I could not find where I left the instructions. I did it many times a few months ago while trying many ROMs, but I could not recall the exact procedure. Then I come to XDA-Devs to search for the info again and find your post sitting there right on top. Thanks, you saved me lots of time.
I'm currently using Erofich's (pArtizAn's) 6.1 standard ROM as well, but wanted to try out Erofich's PRO version for kicks, and maybe retry GnatGoSplat's clean ROM (I found I'm not using Mobile Office , which the Clean ROM leaves out.)
Ideally, I wish there was a way to install certain WM-Pro only applications on WM-Standard, so that I don't need to change to a touch screen centric OS just for a few applications.
BTW, anyone find and use the HTC Network Setup tool to configure the phone for use with U.S. AT&T service. I want to avoid having to manually set up the data settings.
Freakin awesome, works like a charm, now I can flash my phone with the broken charging/sync port. Many thanks...
Hello. I done all steps of this instruction, but can't flash because the message which invite you to press volume button does not appear...
You should repeat the instructions very carefully. Are you sure your SD card is FAT32-formatted, rather than just FAT (FAT16)?
BHSPitMonkey said:
I've just finished successfully flashing an unofficial WM6.1 ROM to my StarTrek (Cingular 3125) using only a microSD card (no data cable, no ActiveSync, no Windows) and the brilliant work found on this forum. I thought I would share the details of my success in the hopes that it will help the next person who stops by, since I myself found it difficult to find a definitive yes/no on the matter here.
Requirements:
HTC StarTrek
I had the Cingular ROM; Any should work.
microSD card
IMPORTANT: Your card MUST be using FAT32 for this to work. If it is not already so, back up its data and do this now. (Windows will show a FAT16 volume simply as "FAT".)
AppUnlock tool
The one linked at this post is good. http://forum.xda-developers.com/showpost.php?p=1146363
The ROM you wish to flash
I used the WM6.1 Standard ROM posted here by Erofich, since it is most appropriate for a Smartphone such as the StarTrek. You can also use the Professional version, though it is intended for use with a touch screen, so you will have to control a cursor with physical keys.
A computer you can use to extract and place these files onto the microSD card.
After you've obtained the listed files and have them extracted somewhere on your computer, copy the following files to your microSD:
SurrealNetworksAppUnlock.cab (Anywhere)
The entire SSPL directory from your extracted ROM download. (Anywhere)
RUU_signed.nbh, found within the RUU directory of your ROM download. (Rename this to STARIMG.NBH and place it in the top-most level of your microSD card, not inside a folder.)
Insert the microSD into the device (the door is located beneath the SIM card). Using the File Explorer (or Total Commander, if you have it), move or copy the three contents of the SSPL directory from your Storage Card to the top level (/) of your phone.
Find the SurrealNetworksAppUnlock.cab file on the Storage Card and run it. It should install like any other application, and you will notice a change to your Home Screen wallpaper.
Using File Explorer again, navigate to the top level (/) of your phone and run SPL.lnk (36 bytes, if this helps you distinguish which file to select). If all goes as expected, you will see a white screen, followed by a message telling you to press the top Volume button to proceed. Do this, and it will flash your new OS to the phone.
I hope I've offered a clear and helpful explanation of this process. Enjoy your now-renascent StarTrek!
Special thanks to Corian for helping me troubleshoot, to #xda-devs, and to all content authors involved here.
Click to expand...
Click to collapse
Dear sir,
Can it be done for my Dopod S300 using the above same method , mine is a original Dopod S 300 Malaysia Rom , CID is locked ? Please let me know before i try your method , thanks for your help and i wish you best regards ,
[email protected]
jimmunsw said:
Dear sir,
Can it be done for my Dopod S300 using the above same method , mine is a original Dopod S 300 Malaysia Rom , CID is locked ? Please let me know before i try your method , thanks for your help and i wish you best regards ,
[email protected]
Click to expand...
Click to collapse
I actually have no idea; What I've posted here is all the experience I have in this department.
Hope you get it figured out!
P.S.: Erofich has a new ROM posted in this subforum; You should check it out if you plan on flashing.
Hi, I will describe your problem in a new topic, because I see that it is broader.
Well, on Friday I bought a HTC HD2 wgranym WM 7 Unfortunately, this system will not even suitable to use, so I decided to upload, and in fact you go back to WM 6.5. I found the forum two ways by dropping LEOIMG.nbh file directly to memory card and a second by installing ROM when connected to a PC.
I bought a memory card reader and format the card. I threw the downloaded file from here: Multiupload.com - upload your files to multiple file hosting sites! Do not give it any more with this phone .... Charter installed a phone and pressing the handset, which is used to activate the phone and the VOL DOWN I switched to a mode. First there was a color screen with the specified data to HD2, but then came the white screen that says "loading ..." and nothing happened for an hour. Perhaps this file does not match my HD2, or he do not know.
The second method seemed to me an alternative and downloaded from the official HTC ROM, giving the serial number. Was surprised that it was a ROM for Norway. I do not know well past the phone, so I do not exclude the possibility that the phone is from Norway. I downloaded the ROM, I downloaded the ActiveSync. But I do not know why when you plug the phone activesync can not connect with them. He writes the message "The device was not detected. " I wanted to try and install without ActiveSync, but the installation failed.
I have no strength, like I'm doing everything ok, but I can not fix this for anything WM 7
Sorry for language errors, I used google translate to translate.
Any help thanks in advance.
okay first of all, if your using windows 7 then you dont need activesync. You need "Windows Media Device Centre"
Also, try turning on the phone whilst holding the volume down button. That should take you to bootloader. (3 colour screen).
You should see the word "serial" at the bottom of the screen.
Connect via USB and wait for the drivers to install.
The word "Serial" should then change to "USB".
Then you can flash a ROM via USB. If your phone is network branded then you will need to flash the correct ROM from the HTC site.
czarinio said:
Hi, I will describe your problem in a new topic, because I see that it is broader.
Well, on Friday I bought a HTC HD2 wgranym WM 7 Unfortunately, this system will not even suitable to use, so I decided to upload, and in fact you go back to WM 6.5. I found the forum two ways by dropping LEOIMG.nbh file directly to memory card and a second by installing ROM when connected to a PC.
I bought a memory card reader and format the card. I threw the downloaded file from here: Multiupload.com - upload your files to multiple file hosting sites! Do not give it any more with this phone .... Charter installed a phone and pressing the handset, which is used to activate the phone and the VOL DOWN I switched to a mode. First there was a color screen with the specified data to HD2, but then came the white screen that says "loading ..." and nothing happened for an hour. Perhaps this file does not match my HD2, or he do not know.
The second method seemed to me an alternative and downloaded from the official HTC ROM, giving the serial number. Was surprised that it was a ROM for Norway. I do not know well past the phone, so I do not exclude the possibility that the phone is from Norway. I downloaded the ROM, I downloaded the ActiveSync. But I do not know why when you plug the phone activesync can not connect with them. He writes the message "The device was not detected. " I wanted to try and install without ActiveSync, but the installation failed.
I have no strength, like I'm doing everything ok, but I can not fix this for anything WM 7
Sorry for language errors, I used google translate to translate.
Any help thanks in advance.
Click to expand...
Click to collapse
You need to take that official ROM, rename it from .exe to .zip, and extract the LEOIMG.nbh file. Place this file in the root directory of your SD card and then go into bootloader like before. This will flash the stock ROM onto your device. Make sure the SD card is fairly low capacity, 2 or 4 GB seems to work best, and formatted for fat32.
Good luck!
czarinio said:
Hi, I will describe your problem in a new topic, because I see that it is broader.
Well, on Friday I bought a HTC HD2 wgranym WM 7 Unfortunately, this system will not even suitable to use, so I decided to upload, and in fact you go back to WM 6.5. I found the forum two ways by dropping LEOIMG.nbh file directly to memory card and a second by installing ROM when connected to a PC.
I bought a memory card reader and format the card. I threw the downloaded file from here: Multiupload.com - upload your files to multiple file hosting sites! Do not give it any more with this phone .... Charter installed a phone and pressing the handset, which is used to activate the phone and the VOL DOWN I switched to a mode. First there was a color screen with the specified data to HD2, but then came the white screen that says "loading ..." and nothing happened for an hour. Perhaps this file does not match my HD2, or he do not know.
The second method seemed to me an alternative and downloaded from the official HTC ROM, giving the serial number. Was surprised that it was a ROM for Norway. I do not know well past the phone, so I do not exclude the possibility that the phone is from Norway. I downloaded the ROM, I downloaded the ActiveSync. But I do not know why when you plug the phone activesync can not connect with them. He writes the message "The device was not detected. " I wanted to try and install without ActiveSync, but the installation failed.
I have no strength, like I'm doing everything ok, but I can not fix this for anything WM 7
Sorry for language errors, I used google translate to translate.
Any help thanks in advance.
Click to expand...
Click to collapse
The easiest way to reflash is using SD Card method.
If you dont have HSPL installed, you should only use this SD Card method to flash the Correct Stock ROM.
Download your correct stock ROM (you must be sure about this, in order to avoid failure). Ectract the downloaded correct stock ROM using 7zip or Winrar. Find the file named: RUU_signed.nbh and rename it to : leoimg.nbh. Place/copy that file to the root directory of your micro sd card (using card reader). For better result, before doing that, you may format your sd card to FAT 32, and copy only that file for flashing purposes only.
Now, put your sd card back to the phone. Go into bootloader mode (by pressing volume down and power on buttons at the same time). Follow the onscreen instruction. Dont forget, to charge your batter before flashing.
goodluck
Thank you all for your responses. I still have one request to you. The set did not get the CD with drivers for HD2. Has anyone can link to them? Thank you in advance.
czarinio said:
Thank you all for your responses. I still have one request to you. The set did not get the CD with drivers for HD2. Has anyone can link to them? Thank you in advance.
Click to expand...
Click to collapse
The Windows Mobile Devive Center has the drivers for the HD2 in it. So when you download the program and install it to your computer you have the drivers. Go to microsoft.com/getstarted to get the WMDC program.