hi ppl,
today I ve made rom with the romkitchen, it was 2003 final and everything went ok, phone was functional until I used to try to install some newer versin of the programs I previously included in the rom. That didnt work (of course) so I decide to put another rom without those programs so I can install newer versions but when I run the romkithen exe computer report
in the dos window
error getconnectiontipe - unspecified error
error getting connectiontype
and the program for the patching report that he is trying to get the data from the device and after that he reports that
"cannot execute the remote communication program, please make sure that the usb/serial cable is properly connectes"
of course cable is connected, device syncing with the active sync and the icon is green, used to try to soft reset pc and pocketpc, to hardware reset pocket pc, to connect it to other pc and patch there, to install active sync 3.7.1, to reinstall active sync 4.2, to reinstall usb drivers on the pc, to put sim card and sd card out and to patch then... nothing helped...
what can I do ? is that due to the windows 2003 instalation on the pocket pc (had same version on other wallaby without the problems) ? can I solve that some way ?
I ve read before that patching can be performed from the SD card so I found the xda tools and osi image tool but couldnt found rom nd1 file anywhere (was stupid and didnt make copy of my previous rom)... which rom can I use just to enable USB connection and after that I ll patch it with the "normal" rom from the rom kitchen...
Ive checked those roms http://wiki.xda-developers.com/index.php?pagename=ROMVersions but didnt find any nd1 file in the files I ve checked, can I use those roms with osi image tool eventually ?
which one ?
Lots of questions ... Sorry people ...
I can use it in this condition too but I d rather have an opportunity to flash it to some other version maybe.
Best regards to the community !
I think it´s just the problem that the ROM prohibits flashing via EXE-file. You have to flash via SD-Card.....
You find the ROm to write on the SD-Card in the EXE-FIle. Just extract the exe using winzip, and then you will find it in a subdirectory (normally english, or dependent on the ROM-Language...)
Stefan
Thanks a lot Stefan, so I can use some ROM from the page http://wiki.xda-developers.com/index.php?pagename=ROMVersions ?
Any advice which one should I take please (Im not using any of the operators noted there, just looking for some rom that will function ok) ?
Thanks m8 !
Yes, you can take any rom of it. Mostly the T-Mobile prohibits flashing via EXE-File, but Flashing via SD-Card is more secure in my opinion. So i´ve done 99,9% of my flashes via SD-Card, and you can believe me, i´ve done it a lot of times.....
By the way, which software has to been updated in my romkitchen?
If you give me the hints, i could try to update them....
Stefan
thanks a lot for your time and advices Stefan !
Its not a huge problem but probably we share same opinion - most of the tech guys like to see that everything work fine, if something doesnt work then we re not satisfied.
Basically problem is that I included spb pocket plus in the rom and therefore I cant install spb weather which demands pocket plus v 2.5+ and version in the rom is 2.0. I cant upgrade it coz its in the ROM, used to try to remove it from the registry but no luck, used to install latest spb diary coz the spb weather also work with the diary but looks like that the first thing weather perform is checking of the pocket plus version and if the version is not 2.5+ it stops the installation...
Probably for the most of the people spb weather is not a reason for loosing couple of hours in trying to change rom in wallaby but as I ve mentioned I like the things that work 100%, if some electronic/computer stuff work at 99% that usually bother me. Stupid - I know but thats the way it is.
Im going to patch it thru the SD, thanks again for the all your efforts now and before.
GL & HF !
Sorry...
Still need help, using the OSI tool I copyed NK.nbf file from 4.02.04_eng rom to "XDA SD Card Slot -unknown size" - coz I dont have card reader/writer at the present moment so I tought that I can put the file via the cradle connection while the card is in the wallaby...
Checked the card from the wallaby file explorer but nothing is on the card, since I had expirience with direct writing to c64 and amiga disks writing I assumed that file could be written directly to the card without OS instructions but after the reset of the wallaby it report that card shoud be formatted to become writable... Is that normal, or I should wait for the card writer reader to put the file properly to the sd card ?
If possible please help me with the link for the OSI tool patching, I cant find it anymore, checked thru the site but no luck, dont know what I have to press so the wallaby read the rom from the sd card.
Thanks Stefan & all others
success !
No help needed, I ve made it...
So dont have any fears as Stefan told unpack the rom from the self extracting archive and run osi tool, in the source field set nbf as a file type and then select extraced rom.
As a target you can set card reader/writer and also you can put the SD card in the wallaby as I did. Set the XDA SD card as a target in that case.
Its normal that after the writing (no message that writing is successfull, when it is finished OSI tool will stop) SD card become unreadable to wallaby.
Then perform actions as noted in SD card patching info
http://wiki.xda-developers.com/index.php?pagename=Wallaby_HT_FlashSD
Hold the power button and soft reset. You'll be taken to the below screen:
SD DOWNLOAD
Card Type:
CE OS & BOOT
Press action to Download
Or
Press REC to Exit
Press action to download and it will start the download/restore from the SD card.
Follow the on screen instructions once its "Completed" which will consist of a " Hard Reset"
Action button mentioned above is middle button - "D PAD"
Works like a charm, now I have o2 win 2002 and later I ll patch it to 2003 SE again but without pocket plus.
Thanks Stefan and community !
Related
:evil:
Hi guys,
I need some serious help here. Today I tried to upgrade my MDA II with the latest 1.60 ROM. Somehow during the upgrade something went wrong and my computer frooze and needed a reset. This was in the beginning 10 minutes of the ROM upgrade and my the screen of my PPC went off. After the reboot of my workstation I could not get my MDA II to connect to my workstation. The MDA is completely useless now. The only thing I have on the screen is:
Serial (or USB) on top of the screen (with no backlight) and at the bottem of the screen Version 1.01.
I can't soft reset of hard reset. I took the battery out and waited for almost 30 minutes but I still can't turn the thing on nor can I soft or hard reset. I can't thing of anything else that I can do and I just sold my Loox yesterday so now I'm lost!
Anybody with a good suggestion??
Please help.
Regards,
Wouter
The Netherlands
I think it's a way to use a SD-card with a Rom on it.
Looks like Your bootloader is still working and can reflash a rom to Your device.
Now You have to find somone with an 64MB SD-card to put a rom on it and reflash Your device.
With best regards
Jens
Hi Jens,
I think my bootloader is not working anymore. I tried to do a hard reset a dozen times but the bootloader menu doesn't come up. But thanks for suggesting though.
Wouter
Hi wouterk,
I don't know if this would be of any help, but you've got nothing to lose now.
I've got a similar error that the RUU program asked me to remove my XDA II from the cradle and right after that, the XDA II screen freeze at "Seria 1.01", same as yours.
So I put my XDA II back to the cradle and from my PC, I clicked Control Panel > System > Device Manager > and here my XDA II was recognized as an unknown device, so I updated the MS USB Sync driver.
After the driver update, I rerun the RUU and the ROM upgrade went fine. Now I have my XDA II back alive and kickin' with the new MDA ROM. At least this works for mine and hope it would also work for yours as well.
HTH.
Hi Joparp,
Of course I gave your suggestion a try. But too bad it didn't work for me like that :? . I remebered that when my workstation crashed, after the reboot it found a new USB device (my cradle?) but I couldn't get your sollution to work for me. But I still have hopes. Tomorrow evening I'll meet a guy who can fix my problem (keep my fingers crossed....). So I feel reasonable relaxed now.
It is nice to see that so many people responded to my problem. I posted my problem on three different sites and many people responded. That was a nice feeling! I keep this thread posted about the result of tomorrow.
B.t.w did you install the 1.60 ROM eventually?
Wouter
Hello wouterk
well, i'm sorry about this and i guess the safest way to do ROM update thru SD Card.
i do agree with jenson suggestion and i can't see any other way to resolve this problem which i hope will work here are the steps as follows :-
ask any one who has MDA II device, 64MB SD Card and SD Card reader to backup his/her ROM and Post it for you somewhere where you can download it and write it to SD Card.
ofcourse he/she if using Windows will need serial cable and hyper terminal software which normally can be fount under start/programs/Accessories/Communication otherwise download from http://www.hilgraeve.com/htpe/index.html
get the device into Bootloader Mode ( power button+any direction+reset )
Connected via Serial cable and use these setting 115200 baud, 8n1, direct to com1 port or maybe com2 it depends on which port they use
type d2s command to backup ROM to SD Card which i recommend 64MB SD card formatted and when done you will see something look like this
D:Waiting for card insert.........
SDetected one card
SD:ready for transfer OK
Total card size=3D40000ze=0
SDCARDD2S+,cStoragePlatformType=FF
********************************************************************************
***********************************************
Store image to SD/MMC card successful.
SER>
then reset the device and get SD card reader and insert this card into the reader and use ntrw image reading and writing tool
if you don't have it you can download it from here http://www.tamiminet.com/othman/ntrw.exe
from the command line run ntrw read MDAII.nb1 E:
This assumes your SD card reader has drive letter E:
now you will have new file which is MDAII.nb1 it's about the size of the SD card zip it and post it somewhere so he/she can Download it and unzip it then write it back to SD Card using this command b]ntrw write MDAII.nb1 E:[/b]
again this assumes your SD card reader has drive letter E:
when done go into bootloader mode ( power button+reset ) with SD card inserted, hit camera button and flash your device with rom which is on SD Card
if you don't have serial cable you still can do it using Linux with cardle and thanks for bio and few other cool guys who mentioned this hints on other thread
put your device in bootloader mode
connect via cradle
use any terminal (minicom) to connect to the used port (/dev/ttyUSB0)
- you should see something like 'USB>' or 'SER>'
put an SD Card into device
type d2s on command prompt
wait untill you see Store image to SD/MMC card successful
i don't think this will include the Applications on the Extended ROM but no problem this can be done later.
i hope this could help to get back you device to life.
best regards and good luck.
Othman
Riyadh, Saudi Arabia
It is working again!
:lol:
Hi guys,
Thanks to Akira my MDA II is working again. Everything is working again exept for the bluetooth communication with my Emtac bluetooth GPS. That problem still remains in my case. I even did another hard reset but still the same problem. I then put the Towa fix again on it and now I can use my GPS again.
So thank you all guys!
Wouter
hi
I have downloaded the wm2003se from lumpinstefan and i could change the rom of my pocket pc to that version by using ActiveSync.
Now i downloaded another version of the rom and i tried to install it on my Qtek 1010 (Wallaby) and it in the black window on my computer appears:
"ERROR: GetConnectionType - An existing connection was forcibly closed by the rem
ote host.
error getting connectiontype"
When i press the next button in the setup it says " cannot execute the remote communication prgram. please make sure that USB/Serial is properly connected". and the setup shuts down.
i Need You to know that before the new rom i downloaded from lumpistefan i was using pocket pc 2002 on my pocket pc.
Now it's clear that there is some problems in the connection. i tried it on several computers but i faced the same problem. is there any setting on my pocket pc to change??
Please somebody helps me i really need to know how to solve the problem.
Regards, and thank you.
Try searching the forum.
It´s an old problem copncerning to some T-Mobile ROMs
You have to flash your device via SD-Card....
Try also some looking in the wiki. The process how to flash vi SD-Card is there described...
And please do not post multiple threads with the same topic....
http://forum.xda-developers.com/viewtopic.php?t=20733
Stefan
ROM Upgrade communication error
Yeah I am having the same problem after installing the T-Mobile ROM, the same communication error when I try and change the installed ROM Image.
I did think it was something wrong with ActiveSync or my laptop :twisted:
Has anyone got any hints on how to do this on a Wannaby? (Saves me getting the wrong idea whilst reading through reams of text).
Many Thanks
Yes i have upgradet my rom via sd card and it worked. it is easy....
Any way thanks so much buddies... tell me something, is there a place in this forum where i can download the windows mobile 2005 version?
2005
I am abit of a newby to this site. I havent seen 2005 yet. Can I ask where I can find instructions for writing an SD card and how to apply to my PDA?
Andy - Whos scratching round for an SD card
ROM Version
Ahh, I see from other threads, ROM Version 4.01.16 prohibits upgrade via EXE! Damn! Ive just checked and thats what I have installed!
The T-Mobile image I'm using at the moment is very slow and comes up with application errors occasionally :x
Re: 2005
amtrakuk said:
I am abit of a newby to this site. I havent seen 2005 yet. Can I ask where I can find instructions for writing an SD card and how to apply to my PDA?
Andy - Whos scratching round for an SD card
Click to expand...
Click to collapse
http://wiki.xda-developers.com/index.php?pagename=Wallaby_HT_FlashSD
HTH
Stefan
Hmm doesnt work for me. I am selecting the browse button to select the nbf file from the image and in the second drop down box selecting the sd card. When I press copy it comes up with the error ITWriteSDCard: The media is write protected, error opening target device. The card isnt locked as I can read and write files to it using explorer. Whats going on?!?!
Growing frustration!!!
A
Some internal SD-Card Writer make problems. i Think you can use also the SD-Card-Slot in your devuce, or you have to get an external Writer...
Stefan
ok my phone is HTC 8525, with WM 6.1 professional . It worked fine for 3 days then it start freezing , before it does that a blue background will appeare ,then it will not let me do anything at all . When I try to touch an icon, it will say something like invalid location or could not find target . I have to hard reset it. sometimes I have to reset it 4 or 5 times a day . , In addition, the mini card will freeze the whole phone is there is a solution like reinstall the whole thing ? please help me I truly appricat it . In addition, the mini card will freeze the whole phone is there is a solution like reinstall the whole thing ?
Hmmm, "the mini card will freeze the whole phone"??? Are you referring to the SD Storage Card? Do you have any volatile data stored on the card? Any Today Screen Applications?
If this is the case, try shutting off the phone and removing the card. Then place the card into a card reader, and plug it into your PC. Make a folder on the desktop of your PC, and COPY all the contents of the SD card to the folder.
Now, reformat the SD card in your PC, as FAT32, and default for all characteristics.
Once reformatted, copy all that stuff back onto the SD card from the temp folder on your desktop, making sure everything is returned to it's original locations. Pop the SD card back into your phone and see if it's fixed. Sometimes, corrupted space on the SD card will make the phone behave very badly. Hopefully, this procedure might fix it for you.
-pvs
Yes Sir, i apaologize , i was refering to the SD card . i am just tierd resetting the phone every 4 hrs . do you recomend any shops that can fix the soft -ware . i notices when i start the phone and i go to clean tmp it will say" 8 Fils and 4 folders of 656 Bytes cleard ! . then 5 hrs later the blue screen comes back
After doing what pvs said, and if you still have problems I'd check for bad blocks with MTTY... I would also ,after confirming no bad blocks, would flash a stock rom then reflash wm 6.1 and see if that helps... Cheers...
Wow , how to do all that if you dont mind me asking , actually i took the SD card out i am not in need for it at the moment . can you please help me to do what you said and i truly appreciat it , Great thanks for both of you gents
pvs already says what to do in his previous post...
To check for bad blocks follow this : http://forum.xda-developers.com/showthread.php?t=377389
To Flash a stock rom you need to know what carrier the phone was on. Download the wm6 update from their site and, Making sure you have Hard SPLed your phone, I suggest flashing via the sd card method. Its safer than flashing through pc.
Format sd card fat32. copy .nbh file of the stock rom (you may have to search for it) onto the sd card and rename to "hermimg.nbh". Put back in hermes and reset to bootloader (power button, OK button above flywheel and soft reset with stylus. Hold all buttons until it goes to tri-colour screen). It should recognise the os flash and load up a screen showing 1st boot screen, 2nd boot screen, gsm And os (or something like that as cooked roms don't generally have the gsm part). MAKE SURE YOU HAVE AT LEAST 50% BATTERY!!!!! Follow the prompts... I generally use the sd card method to flash ALL my roms so I don't have problems like usb disconnecting or pc rebooting/hanging or power failures.
Hope this helps you out, Cheers...
BASELABBAS ... Please describe what you are doing when you say that you are "HARD-RESETTING" several times a day. Are you:
1) poking the stylus into the hole at the base of the unit?
- or -
2) holding down the two soft-keys WHILE poking the stylus into the hole until the confirmation screen appears, and then opening the keyboard and typing 'R' and then [SPACEBAR]?
If you are doing the first ... this is called a SOFT reset. The second is a HARD-RESET, and will wipe the phone clean of ANYTHING outside of what came with the ROM itself.
Since you have posted that you already removed the SD Card from the device, and can (for the time-being) live without it, I recommend you do an ACTUAL Hard Reset (backup anything you need to keep first) via step #2 above, and then be patient about installing any apps. I wouldn't do anything more than sync it up via ActiveSync with your contacts for the first few of days. If things start to go crazy without any third-party apps installed, then I would look into the steps that ultramag69 has suggested ... starting with a flash to a stock ROM.
WM6.1 has been a bit shaky on our Hermes thus far. Some people are getting good results, but a lot of others are having issues like you are describing. I would suspect that your ROM might not be a good match, before I'd suspect bad blocks at this point (and it's a bit easier to test for).
If the stock rom does better on your device, you can try flashing back up to a WM6.1 ROM after that. And if you haven't already, make sure that you have installed HARDSPL before doing any of this stuff.
Good luck,
-pvs
Mr. pvs , I am doing the #2 holding down the two soft-keys WHILE poking the stylus into the hole until the confirmation screen appears, and then opening the keyboard and typing 'R' and then [SPACEBAR]. I tried to download Hard-SPL 1[1].10, when I open it on my PC it will give me instructions then when I press upgrade I will see 4 color screen the Sync icon will disappear and then it will say that it lost connections.
it looks like i need to update
this what is say
From :
Image Version : TNT.19199
to
image version 2.05.255.1
BASELABBAS said:
Mr. pvs , I am doing the #2 holding down the two soft-keys WHILE poking the stylus into the hole until the confirmation screen appears, and then opening the keyboard and typing 'R' and then [SPACEBAR].
Click to expand...
Click to collapse
OK, well that's definitely a Hard Reset. So your WM6.1 Rom is acting flaky right aftwerwards, eh? I would say it's time to try a different ROM, as we've been discussing above.
BASELABBAS said:
I tried to download Hard-SPL 1[1].10, when I open it on my PC it will give me instructions then when I press upgrade I will see 4 color screen the Sync icon will disappear and then it will say that it lost connections.
Click to expand...
Click to collapse
No ... try Hard-SPL-V7.zip found at the bottom of THIS PAGE. I THINK you can flash it via the SD method if ActiveSync isn't working for you (if not, somebody please correct me). To do this, open the downloaded ZipFile with WinZip or WinRAR and copy the file inside named RUU_signed.nbh to your desktop. Rename it HERMIMG.NBH, and copy it to the root of your freshly reformatted (FAT32) Storage Card. Put the Storage Card into your device and press the side OK button and the power button simultaneously while resetting with the stylus until the tri-color screen appears and turns white. The device will find the HERMIMG.NBH file and offer to upgrade by pressing the Power Key. This will install HardSPL onto your device without the need for ActiveSync. You can also flash ROMs in this manner.
Again, good luck,
-pvs
No, You need to run a file from the phone itself to install hard SPLvia sd card. You can find it on page 116 of the hard SPL or how not to brick your hermes thread.
Cheers...
ultramag69 said:
No, You need to run a file from the phone itself to install hard SPLvia sd card. You can find it on page 116 of the hard SPL or how not to brick your hermes thread.
Cheers...
Click to expand...
Click to collapse
Thanks for checking me on that, Ultramag. I had a feeling there was something I was forgetting.
-pvs
I've just finished successfully flashing an unofficial WM6.1 ROM to my StarTrek (Cingular 3125) using only a microSD card (no data cable, no ActiveSync, no Windows) and the brilliant work found on this forum. I thought I would share the details of my success in the hopes that it will help the next person who stops by, since I myself found it difficult to find a definitive yes/no on the matter here.
Requirements:
HTC StarTrek
I had the Cingular ROM; Any should work.
microSD card
IMPORTANT: Your card MUST be using FAT32 for this to work. If it is not already so, back up its data and do this now. (Windows will show a FAT16 volume simply as "FAT".)
AppUnlock tool
The one linked at this post is good. http://forum.xda-developers.com/showpost.php?p=1146363
The ROM you wish to flash
I used the WM6.1 Standard ROM posted here by Erofich, since it is most appropriate for a Smartphone such as the StarTrek. You can also use the Professional version, though it is intended for use with a touch screen, so you will have to control a cursor with physical keys.
A computer you can use to extract and place these files onto the microSD card.
After you've obtained the listed files and have them extracted somewhere on your computer, copy the following files to your microSD:
SurrealNetworksAppUnlock.cab (Anywhere)
The entire SSPL directory from your extracted ROM download. (Anywhere)
RUU_signed.nbh, found within the RUU directory of your ROM download. (Rename this to STARIMG.NBH and place it in the top-most level of your microSD card, not inside a folder.)
Insert the microSD into the device (the door is located beneath the SIM card). Using the File Explorer (or Total Commander, if you have it), move or copy the three contents of the SSPL directory from your Storage Card to the top level (/) of your phone.
Find the SurrealNetworksAppUnlock.cab file on the Storage Card and run it. It should install like any other application, and you will notice a change to your Home Screen wallpaper.
Using File Explorer again, navigate to the top level (/) of your phone and run SPL.lnk (36 bytes, if this helps you distinguish which file to select). If all goes as expected, you will see a white screen, followed by a message telling you to press the top Volume button to proceed. Do this, and it will flash your new OS to the phone.
I hope I've offered a clear and helpful explanation of this process. Enjoy your now-renascent StarTrek!
Special thanks to Corian for helping me troubleshoot, to #xda-devs, and to all content authors involved here.
Funny, I was planning on re-flashing my 3125 via SD card, but I could not find where I left the instructions. I did it many times a few months ago while trying many ROMs, but I could not recall the exact procedure. Then I come to XDA-Devs to search for the info again and find your post sitting there right on top. Thanks, you saved me lots of time.
I'm currently using Erofich's (pArtizAn's) 6.1 standard ROM as well, but wanted to try out Erofich's PRO version for kicks, and maybe retry GnatGoSplat's clean ROM (I found I'm not using Mobile Office , which the Clean ROM leaves out.)
Ideally, I wish there was a way to install certain WM-Pro only applications on WM-Standard, so that I don't need to change to a touch screen centric OS just for a few applications.
BTW, anyone find and use the HTC Network Setup tool to configure the phone for use with U.S. AT&T service. I want to avoid having to manually set up the data settings.
Freakin awesome, works like a charm, now I can flash my phone with the broken charging/sync port. Many thanks...
Hello. I done all steps of this instruction, but can't flash because the message which invite you to press volume button does not appear...
You should repeat the instructions very carefully. Are you sure your SD card is FAT32-formatted, rather than just FAT (FAT16)?
BHSPitMonkey said:
I've just finished successfully flashing an unofficial WM6.1 ROM to my StarTrek (Cingular 3125) using only a microSD card (no data cable, no ActiveSync, no Windows) and the brilliant work found on this forum. I thought I would share the details of my success in the hopes that it will help the next person who stops by, since I myself found it difficult to find a definitive yes/no on the matter here.
Requirements:
HTC StarTrek
I had the Cingular ROM; Any should work.
microSD card
IMPORTANT: Your card MUST be using FAT32 for this to work. If it is not already so, back up its data and do this now. (Windows will show a FAT16 volume simply as "FAT".)
AppUnlock tool
The one linked at this post is good. http://forum.xda-developers.com/showpost.php?p=1146363
The ROM you wish to flash
I used the WM6.1 Standard ROM posted here by Erofich, since it is most appropriate for a Smartphone such as the StarTrek. You can also use the Professional version, though it is intended for use with a touch screen, so you will have to control a cursor with physical keys.
A computer you can use to extract and place these files onto the microSD card.
After you've obtained the listed files and have them extracted somewhere on your computer, copy the following files to your microSD:
SurrealNetworksAppUnlock.cab (Anywhere)
The entire SSPL directory from your extracted ROM download. (Anywhere)
RUU_signed.nbh, found within the RUU directory of your ROM download. (Rename this to STARIMG.NBH and place it in the top-most level of your microSD card, not inside a folder.)
Insert the microSD into the device (the door is located beneath the SIM card). Using the File Explorer (or Total Commander, if you have it), move or copy the three contents of the SSPL directory from your Storage Card to the top level (/) of your phone.
Find the SurrealNetworksAppUnlock.cab file on the Storage Card and run it. It should install like any other application, and you will notice a change to your Home Screen wallpaper.
Using File Explorer again, navigate to the top level (/) of your phone and run SPL.lnk (36 bytes, if this helps you distinguish which file to select). If all goes as expected, you will see a white screen, followed by a message telling you to press the top Volume button to proceed. Do this, and it will flash your new OS to the phone.
I hope I've offered a clear and helpful explanation of this process. Enjoy your now-renascent StarTrek!
Special thanks to Corian for helping me troubleshoot, to #xda-devs, and to all content authors involved here.
Click to expand...
Click to collapse
Dear sir,
Can it be done for my Dopod S300 using the above same method , mine is a original Dopod S 300 Malaysia Rom , CID is locked ? Please let me know before i try your method , thanks for your help and i wish you best regards ,
[email protected]
jimmunsw said:
Dear sir,
Can it be done for my Dopod S300 using the above same method , mine is a original Dopod S 300 Malaysia Rom , CID is locked ? Please let me know before i try your method , thanks for your help and i wish you best regards ,
[email protected]
Click to expand...
Click to collapse
I actually have no idea; What I've posted here is all the experience I have in this department.
Hope you get it figured out!
P.S.: Erofich has a new ROM posted in this subforum; You should check it out if you plan on flashing.
Hi, I will describe your problem in a new topic, because I see that it is broader.
Well, on Friday I bought a HTC HD2 wgranym WM 7 Unfortunately, this system will not even suitable to use, so I decided to upload, and in fact you go back to WM 6.5. I found the forum two ways by dropping LEOIMG.nbh file directly to memory card and a second by installing ROM when connected to a PC.
I bought a memory card reader and format the card. I threw the downloaded file from here: Multiupload.com - upload your files to multiple file hosting sites! Do not give it any more with this phone .... Charter installed a phone and pressing the handset, which is used to activate the phone and the VOL DOWN I switched to a mode. First there was a color screen with the specified data to HD2, but then came the white screen that says "loading ..." and nothing happened for an hour. Perhaps this file does not match my HD2, or he do not know.
The second method seemed to me an alternative and downloaded from the official HTC ROM, giving the serial number. Was surprised that it was a ROM for Norway. I do not know well past the phone, so I do not exclude the possibility that the phone is from Norway. I downloaded the ROM, I downloaded the ActiveSync. But I do not know why when you plug the phone activesync can not connect with them. He writes the message "The device was not detected. " I wanted to try and install without ActiveSync, but the installation failed.
I have no strength, like I'm doing everything ok, but I can not fix this for anything WM 7
Sorry for language errors, I used google translate to translate.
Any help thanks in advance.
okay first of all, if your using windows 7 then you dont need activesync. You need "Windows Media Device Centre"
Also, try turning on the phone whilst holding the volume down button. That should take you to bootloader. (3 colour screen).
You should see the word "serial" at the bottom of the screen.
Connect via USB and wait for the drivers to install.
The word "Serial" should then change to "USB".
Then you can flash a ROM via USB. If your phone is network branded then you will need to flash the correct ROM from the HTC site.
czarinio said:
Hi, I will describe your problem in a new topic, because I see that it is broader.
Well, on Friday I bought a HTC HD2 wgranym WM 7 Unfortunately, this system will not even suitable to use, so I decided to upload, and in fact you go back to WM 6.5. I found the forum two ways by dropping LEOIMG.nbh file directly to memory card and a second by installing ROM when connected to a PC.
I bought a memory card reader and format the card. I threw the downloaded file from here: Multiupload.com - upload your files to multiple file hosting sites! Do not give it any more with this phone .... Charter installed a phone and pressing the handset, which is used to activate the phone and the VOL DOWN I switched to a mode. First there was a color screen with the specified data to HD2, but then came the white screen that says "loading ..." and nothing happened for an hour. Perhaps this file does not match my HD2, or he do not know.
The second method seemed to me an alternative and downloaded from the official HTC ROM, giving the serial number. Was surprised that it was a ROM for Norway. I do not know well past the phone, so I do not exclude the possibility that the phone is from Norway. I downloaded the ROM, I downloaded the ActiveSync. But I do not know why when you plug the phone activesync can not connect with them. He writes the message "The device was not detected. " I wanted to try and install without ActiveSync, but the installation failed.
I have no strength, like I'm doing everything ok, but I can not fix this for anything WM 7
Sorry for language errors, I used google translate to translate.
Any help thanks in advance.
Click to expand...
Click to collapse
You need to take that official ROM, rename it from .exe to .zip, and extract the LEOIMG.nbh file. Place this file in the root directory of your SD card and then go into bootloader like before. This will flash the stock ROM onto your device. Make sure the SD card is fairly low capacity, 2 or 4 GB seems to work best, and formatted for fat32.
Good luck!
czarinio said:
Hi, I will describe your problem in a new topic, because I see that it is broader.
Well, on Friday I bought a HTC HD2 wgranym WM 7 Unfortunately, this system will not even suitable to use, so I decided to upload, and in fact you go back to WM 6.5. I found the forum two ways by dropping LEOIMG.nbh file directly to memory card and a second by installing ROM when connected to a PC.
I bought a memory card reader and format the card. I threw the downloaded file from here: Multiupload.com - upload your files to multiple file hosting sites! Do not give it any more with this phone .... Charter installed a phone and pressing the handset, which is used to activate the phone and the VOL DOWN I switched to a mode. First there was a color screen with the specified data to HD2, but then came the white screen that says "loading ..." and nothing happened for an hour. Perhaps this file does not match my HD2, or he do not know.
The second method seemed to me an alternative and downloaded from the official HTC ROM, giving the serial number. Was surprised that it was a ROM for Norway. I do not know well past the phone, so I do not exclude the possibility that the phone is from Norway. I downloaded the ROM, I downloaded the ActiveSync. But I do not know why when you plug the phone activesync can not connect with them. He writes the message "The device was not detected. " I wanted to try and install without ActiveSync, but the installation failed.
I have no strength, like I'm doing everything ok, but I can not fix this for anything WM 7
Sorry for language errors, I used google translate to translate.
Any help thanks in advance.
Click to expand...
Click to collapse
The easiest way to reflash is using SD Card method.
If you dont have HSPL installed, you should only use this SD Card method to flash the Correct Stock ROM.
Download your correct stock ROM (you must be sure about this, in order to avoid failure). Ectract the downloaded correct stock ROM using 7zip or Winrar. Find the file named: RUU_signed.nbh and rename it to : leoimg.nbh. Place/copy that file to the root directory of your micro sd card (using card reader). For better result, before doing that, you may format your sd card to FAT 32, and copy only that file for flashing purposes only.
Now, put your sd card back to the phone. Go into bootloader mode (by pressing volume down and power on buttons at the same time). Follow the onscreen instruction. Dont forget, to charge your batter before flashing.
goodluck
Thank you all for your responses. I still have one request to you. The set did not get the CD with drivers for HD2. Has anyone can link to them? Thank you in advance.
czarinio said:
Thank you all for your responses. I still have one request to you. The set did not get the CD with drivers for HD2. Has anyone can link to them? Thank you in advance.
Click to expand...
Click to collapse
The Windows Mobile Devive Center has the drivers for the HD2 in it. So when you download the program and install it to your computer you have the drivers. Go to microsoft.com/getstarted to get the WMDC program.