Help me somebody. I need image file for upgrade my ppc from SD Card.
My T-Mobile stuck in bootloader mode, and i cant upgrade new rom from my PC. I have no cable and no cradle.
If someone knows, help to find an image, please.
Related
OK I used the ROM Kitchen to mave a .eve of the upgrade to WM 2003. In the middle of the process my device lost the connection. Now my device is sitting at the upgrade screen telling me it will be done in 5 min.
What can I do?
i had that happen to me today!
usualy, you restart the .exe and insert the xda,
it will restart the process on its own.
if not, go it the SD card method, as described somewhere in this forum.
good luck.
Hmm...
Because I always use the SD method, I have never used the exe files. My guess would be to soft reset the device and hope that when you put it in the cradle again it will let you run the exe. You may try putting it in the cradle while its in bootloader mode if just a soft reset doesn't work. Only other thing I could offer is to write it to an SD card for you - but that would require you mailing me the SD card + rom, me mailing it back, and a lot more than 5 minutes.
Let us know how it works out.
I am trying the SD way. However, program that is suggested does not appear to be writing anything to my SD card. I have a 6 in 1 USB card reader. Any the program ask you to pick drive 2-4. I have tried all drives and can not see the image file when I try to view the contents of the SD card on my PC
You're not going to see the contents when you try to view it on your PC - your PC will tell you the card isn't formatted.
I have resolved my problem thanks for the help!
As a result of a car accident I lost the ability to connect my Himalaya using the USB cradle. The data port on the phones board was completely smashed. I had it repaired only to allow my xdaII to recharge from it's power adapter but not from the cradle, that's how I lost all usb functionality.
Now I've previously read some methods and instructions on how to upgrade the xdaII using some modified rom files which are then stored on a SD-Card and then installed from the bootloader without the use of a USB connection.
Can anyone here tell me exactly how this is done ? What are the steps needed to convert the available rom files on this site to a format that would work from the sd-card ? I would also like to know, whether this method supports upgrading the radio and the extended rom in addition to the windows rom ?
Your help and assistance on this matter will be highly appreciated. As I can no longer upgrade my phone using the usb method. I will be depending on your help you guys. I've got faith in u, so don't let me down.
I also want to know it! Please help!!
Find another xda2 that has a working USB connection, insert your SD card in it, and use the attached file to copy the rom to your sd card. Then place the sd card in your xda2 go to boot loader mode and that is it.
The only problem is that whenever you want to change the rom version you will have to use another xda2 that has a working usb to transfere the rom image on your sd card.
Hi Guys,
I was hoping you can help me out. I have an HTC 8525 that no longer connects to my computer via USB. I believe that a pin on the inside is damaged. I would like to upgrade to the Schaps ROM but have not found a way to flash from my microSD card. I read the information in the Wiki but when following the steps I end up at a screen with red, blue, green, and white bars that say serial. After hitting the power button the flash does not start. Am i missing a step or is what I'm trying to do not possible?
Thanks in advance for any help,
Chad
did you rename the nbh file to HERMIMG.nbh? and make sure the card is formatted to fat32
more importantly........did you hardspl your device first?
Yes and Yes. I did not HardSPL my device. I'll have to see if I can find instructions in the forum.
If its helps my bootloader screen shows IPL-1.04 on the red color and HEM 100 SPL-2.03 also on the red tabl
You need do do HARD SPL if yoy want to flash from SD card.
How do I that if I cannot connect by device via USB?
Can anyone advise me as to whether or not it's possible to install hard SPL without being able to use active sync?
it is possible!
1. Format your SD card with FAT32.
2. Download Hermes SIM CID Unlock v3a.
3. Copy SSPL-HERM to your SD card.
4. Extract the RUU_HERM_Unlock_v3a.
5. copy HermesUnlocker_HardSPL.nbh to SD card.
6. Rename it to HERMIMG.nbh.
7. put the SD card into the device and run sspl.exe.
8. the device enters the bootloader and ...
Thanks. You're the man. That worked like a charm
http://youtube.com/watch?v=yoN7dMm8KEY
Try that i have made one for the Wizard also Check them out hope they work
Hi,
i have a few chinese tablets and i got a update that i am trying to apply. Got the PhoenixUSBPro program, which do not recognize the tablet, so i am not able to upgrade via PC.
I would like to upgrade via external ( or internal if there´s any difference ), i got an image file and a .key file, what should i do in order to be able to upgrade via sd card ?
Thankful for helping answers.
Hi, ive got this old bricked tablet, cant enter recovery mode, not recognized in windows when in fastboot mode, nothing working basicaly,
i want to flash it and i CAN'T, its getting frustrating after 3 days i decided to ask help here!
this is where im stuck:
i want to use Rockchip SD disk tool 1.59 to make a bootable SD card for automatic flashing.
First sd card not working, SD disk tool keeps saying loading firmware failed, ok buy a new SD card San disk 16gb
perfect it works!i managed to create a bootable flash IMG but its not flashing or doing anything when powered on with sd in it.
so i try to reflash it on the card, and it keeps giving error again now even on the new SD card : Loading firmware failed! I tried using SD card formatter to format the card, still loading firmware failed!
somebody please help me before i lose my sanity, i cant sleep because of this i want to handle it so badly.
edit:
oh and i dont think usb debugging and oem unlocking are turned on and i cant check!
EDIT 2: OK so i figured out how to fix the loading firmware failed, on the SD card formatter i had to tick the box , overwrite format! this fixed it, but the main problem still remains, the tablet wont boot and flash from the SD card.
EDIT3:
solved by flashing stock rom using fastboot in linux, or maybe Linux_Upgrade_Tool_v1.2 , i cant remember which of these worked in the end, i just know linux upgrade tool was hell to use, with chinese instructions