Related
Hello.
I have a problem I hope someone here can help me to solve..
I have an Orange SPV M3100 that hangs on the Windows Mobile screen when I try to start it.
I'm able to go into bootloader mode, and i have tried using mtty142.exe with the set 14 0 command. It still won't boot. I've also tried to hard reset it.. still won't boot..
What I did was trying to unluck the SIM-lock with the Universal unlocker (HTC_Uni_Unlock_v1) from buzz. At the time I thought universal meant that it worked on all HTC devices (stupid, I know)... And I also thought it was harmless to just try and see if it worked. But I got an error around 92-93% and after that my device won't start. So my radio ROM might be screwed.
I'd like to flash my ROM with the i-mate one (JASJAM_WWE_1.20.305.3_1.20.305.104_1.07.03.10_ship.exe) and then add the ext-rom. But how do I do that when I can just access the bootloader screen? And do you think it will boot again if I'm able to flash it?
Here's some more info about my device:
HERM100
IPL-1.01
SPL-1.04
Thank you very much in advance. Help will be highly appreciated.
No your rom *is* screwed. You can get into bootloader, you can even get to 11% of a dopod etc rom upgrade if you try, but you will not flash a new radio.
You CAN boot the device.
Do a hard reset, but do not press spacebar to reboot after. Instead, do a soft reset. The unit should boot but as you've screwed the radio you will not get a gsm signal and the phone will say unknown sim status.
I know this as I bought one cheap after the owner had done exactly the same as you.
IMEI-check's unlock solution is the only one that works IIRC, and in some cases this re-writes the security area of the phone and repairs similar issues, but in this case I could not get the prog to read.
You need to return the device to HTC - you'll need to pay approx £35 for reflashing back to the orange rom. This is what I had to do.
Currently you cannot book the m3100 in through the web as it's too new, instead email / call them.
http://service.htceurope.com/
edit - or if you're an orange customer ring 150 and act dumb saying it ' won't work'.... :wink:
Richard
What happens if you just leave the phone in bootloader mode and then try to flash any ROM (imate, dopod, htc...)? run 2 times the RomUpgradeUt.exe if you get an error on the 1st try.
If you get an error while running the rom upgrade utility you can monitor the USB port while upgrading (you will see the real error from the bootloader then), there's some more info on this wiki page:
http://wiki.xda-developers.com/index.php?pagename=Hermes_BootLoader
good luck
pof said:
What happens if you just leave the phone in bootloader mode and then try to flash any ROM (imate, dopod, htc...)? run 2 times the RomUpgradeUt.exe if you get an error on the 1st try.
If you get an error while running the rom upgrade utility you can monitor the USB port while upgrading (you will see the real error from the bootloader then), there's some more info on this wiki page:
http://wiki.xda-developers.com/index.php?pagename=Hermes_BootLoader
good luck
Click to expand...
Click to collapse
No, if you want to send it back under warranty do not try to run a rom update as there are no orange rom packages. As described in my post above, it will get to 11% and stop. The device will be in the same state as before, with the same ext rom, but the splash screen and bootloader will have changed.
i.e: it will be bloomin obvious you tried flashing it and failed. Not what you want if you try for a warranty repair....
There is no error from the bootloader - as there is no radio rom present and no security area the upgrade process just hangs.
Richard
fluffcat1 said:
No, if you want to send it back under warranty do not try to run a rom update as there are no orange rom packages.
[...]
i.e: it will be bloomin obvious you tried flashing it and failed. Not what you want if you try for a warranty repair....
Click to expand...
Click to collapse
That's true, do not try to flash any other roms if you want to use the warranty or send the device back...
Thank you very very much for your help guys.
As I'm the administrator of these devices in the company I work for I just grabbed a new SPV and will send this thing back to Orange. It sounded like I'm getting a new one..
Well, I think I've learnt my lession.
Oh, and I have another question. Is there a reg editor I can install on this one so I can remove the app lock? I know I can install java apps, but it's a bit grumpy about apps that needs installation (the developer must be certificated).
Cheers guys.
Hi,
Try to flash a new rom using the SD card method described here:
http://forum.xda-developers.com/viewtopic.php?t=62596
The rom must match your CID. Let us know if it works
pof said:
Hi,
Try to flash a new rom using the SD card method described here:
http://forum.xda-developers.com/viewtopic.php?t=62596
The rom must match your CID. Let us know if it works
Click to expand...
Click to collapse
Errr, did you read the last post? He sent it back......
Richard
I just wanted to let him know there's a possible solution, it just in case he still has the unit
pof said:
I just wanted to let him know there's a possible solution, it just in case he still has the unit
Click to expand...
Click to collapse
Maybe his search is broken as well as his old phone eh?.... :roll:
fluffcat1 said:
You need to return the device to HTC - you'll need to pay approx £35 for reflashing back to the orange rom. This is what I had to do.
Click to expand...
Click to collapse
Sorry to take the thread a bit OT, but just wanted to confirm this again.
So, if I flashed my M3100 with a different ROM, and then had to return the phone to Orange for repair for a different reason, I can send it back to HTC just to have the ROM reflashed, and then send the phone to Orange to get the repairs done?
I've been hesitating on whether to flash the phone with a non-Orange ROM because I didn't want to give up the ability to obtain warranty repair (as there is no ROM upgrade yet). If it's just a matter of £35 and then everything else as normal, maybe it's not so bad...
Thanks!
My SPV M3100 won't start!!!
I also did this, so if anyone can find a solution it would be greatly appreciated.
Also tried this and it didn't work for me:
Try to flash a new rom using the SD card method described here:
http://forum.xda-developers.com/viewtopic.php?t=62596
"I have a problem I hope someone here can help me to solve..
I have an Orange SPV M3100 that hangs on the Windows Mobile screen when I try to start it.
I'm able to go into bootloader mode, and i have tried using mtty142.exe with the set 14 0 command. It still won't boot. I've also tried to hard reset it.. still won't boot..
What I did was trying to unluck the SIM-lock with the Universal unlocker (HTC_Uni_Unlock_v1) from buzz. At the time I thought universal meant that it worked on all HTC devices (stupid, I know)... "
rachelm700 said:
I also did this, so if anyone can find a solution it would be greatly appreciated.
Also tried this and it didn't work for me:
Try to flash a new rom using the SD card method described here:
http://forum.xda-developers.com/viewtopic.php?t=62596
"I have a problem I hope someone here can help me to solve..
I have an Orange SPV M3100 that hangs on the Windows Mobile screen when I try to start it.
I'm able to go into bootloader mode, and i have tried using mtty142.exe with the set 14 0 command. It still won't boot. I've also tried to hard reset it.. still won't boot..
What I did was trying to unluck the SIM-lock with the Universal unlocker (HTC_Uni_Unlock_v1) from buzz. At the time I thought universal meant that it worked on all HTC devices (stupid, I know)... "
Click to expand...
Click to collapse
the above link doesnt work?
zohaer21 said:
the above link doesnt work?
Click to expand...
Click to collapse
IIRC it is this link on the new forum:
http://forum.xda-developers.com/showthread.php?t=277281
spv m3100 don't start
hello guys
I have the same problem about spv m3100. I used "universal unlock tool" to unlock my device and now it don't start,don't boot...I tried the Hermes SD Card flashing methods with qtek001 rom and, a white screen with "loading...." appears for 2 second and then nothing else appened. I think that the method is right but I need to use a different software. what do you think about?
please help me
thankksssss
My SPV M3100 won't start
SD card method is no good as there is no upgrade from Orange until January.
Tried to do a radio upgrade explained here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms
But it didn't work just came up with connection error, tried to monitor USB but nothing showed up to find out why, althouth mtty commands always do show up in USB Monitor.
Still have a brick and looking for a solution, hopefully, someday, please someone help me I am loosing my mind.
Hello
How to enter boot mode on HTC 200 ?
My htc hangs on HTC screen.
I'm trying to reflash it.
Thanx
Chris
@chrisro, Please read the wiki:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
http://wiki.xda-developers.com/index.php?pagename=Hermes_Resets
Thank you very much.
Greets form Poland !
Chris
I was flashing my brothers phone for him, and I was using the CID Workaround, and it completed, and then after a hard reset the device wouldnt go past the first splash screen.. pllease help
If your able to get into bootloader mode then you should be able to flash another rom such as wizard love or your providers rom.
If you read the thread on unlocking G4 cid locked using shell tool you will see what i mean. I personally was stuck in a very similar situation and received help, so the info you need might be in that thread.
nstefanelli said:
I was flashing my brothers phone for him, and I was using the CID Workaround, and it completed, and then after a hard reset the device wouldnt go past the first splash screen.. pllease help
Click to expand...
Click to collapse
Check your PM's
bwesty said:
If your able to get into bootloader mode then you should be able to flash another rom such as wizard love or your providers rom.
If you read the thread on unlocking G4 cid locked using shell tool you will see what i mean. I personally was stuck in a very similar situation and received help, so the info you need might be in that thread.
Click to expand...
Click to collapse
i used the shell tool, but i just got stuck on the first splash after i did that.... here are device specs
Its a Cingular 8125, obivously g4
IPL 2.25.0001
SPL 2.25.0001
It doesnt get past bootloader, and I would really like to put WM6 on it.
At this point, I've tried various other ROMs and nothing is working. Any thoughts or ideas at all would be appreciated. Thanks.
jUST DO WHAT I SAY
gREETINGS,
Just follow this steps u will be out of it.
Press and hold the camera button and reset the phone, hold the camera button until you see the tri color screen (bootloader), when u are on tri color screen connect the USB with your phone(dont see for active sync it wont recognise but it will be connected), and then flash your phone with the rom your provider has given you i.e, the original rom and DONT flash it with shell tool use the exe file of the rom.
When you are at the original rom then try to flash the WM6 with shell tool and follow the instruction properly.
Thanks
samy.3660 said:
gREETINGS,
Just follow this steps u will be out of it.
Press and hold the camera button and reset the phone, hold the camera button until you see the tri color screen (bootloader), when u are on tri color screen connect the USB with your phone(dont see for active sync it wont recognise but it will be connected), and then flash your phone with the rom your provider has given you i.e, the original rom and DONT flash it with shell tool use the exe file of the rom.
When you are at the original rom then try to flash the WM6 with shell tool and follow the instruction properly.
Thanks
Click to expand...
Click to collapse
I cannot do that because the Carrier ROMs that I have aren't for G4, so they arent working. I have three different carrier ROMs for my phone.. and none of them work.
-Stefanelli-
nstefanelli said:
i used the shell tool, but i just got stuck on the first splash after i did that.... here are device specs
Its a Cingular 8125, obivously g4
IPL 2.25.0001
SPL 2.25.0001
It doesnt get past bootloader, and I would really like to put WM6 on it.
At this point, I've tried various other ROMs and nothing is working. Any thoughts or ideas at all would be appreciated. Thanks.
Click to expand...
Click to collapse
Check your email, I downloaded and zip works fine here.
i'm facing this problem right now , i will solve it with the original rom .
the problem started when i used shelltool to upgrade my G4 CID Locked to windows mobile 6 crossbow underground edition .
i will give it another try when i get my device alive again ,
any suggestions for the WM6 underground to make it work using shelltool on my wiza 200 ??
--------------------- Edit -----------------------
Finally i solved the problem and installed Crossbow WM6 underground edition .
all i did is to install the original rom from provider and then used shelltool to install WM6 .
i want to mention that my wiza200 is G4 and its CID Locked .
Huge thanx to mUn , you are da man
Mmm
I've tried underground wm6, but flashing till 96%, then error 302. I've searching for love rom few hours at night, then finally found, it is using the same flashing frontend (but in italian? language), flashed ok, phone's running. I've tried some few other wm6 roms, but always errors like "too old, get new one" or once it was probably fake, because it loaded exactly the same ROM as love one is. So, now I've probably stuck on WM5 at all
lobiik said:
I've tried underground wm6, but flashing till 96%, then error 302. I've searching for love rom few hours at night, then finally found, it is using the same flashing frontend (but in italian? language), flashed ok, phone's running. I've tried some few other wm6 roms, but always errors like "too old, get new one" or once it was probably fake, because it loaded exactly the same ROM as love one is. So, now I've probably stuck on WM5 at all
Click to expand...
Click to collapse
whats your device and is it G3 or G4 ?
try to do as i did and it worked for me , install the provider flash , then try shelltool to flash WM6 underground .
WBR
a-h-t1 said:
whats your device and is it G3 or G4 ?
Click to expand...
Click to collapse
Mine is G4, dunno if cid is locked or not. I've flashed it as I said with wizard love rom and working without problems. I've tried that again this morning, to flash from love rom, but the same. At 96% it hangs, error 302 Communication error, then starts recovery process, phone goes to bootloader mode. Then is possible to flash it with love rom again with no problem
g4
i have a g4 wizard using the shell tool i have chaged my rom on my phone sometimes 3 times a week just to test them out
the shell tool works if you cant download from the forum here is the link for it
http://rapidshare.com/files/17787647/ShellTool_bugfixed.zip
G4
yes, but when I run shelltool, and press get rom info, all fields states N/A
info from phone is:
ROM Version: 2.26.10.2 WWE
Radio: 2.25.11
ExtROM: 2.26.10.105
IPL/SPL: 2.17.0001
And anyway, dunno exactly which rom for WM6 I can put in (I've just 5.underground_edition_Crossbow_ROM.exe which stucks at 96% with 302 error)
well, I'm dumb, mislooked one stupid thing. Everything passed without errors, Windows Mobile 6 is up and running
happy to know that , the problem was installing rapi ha ??
WBR
No, not really, rapi and that second cab was in device, it was restarted, but I did a mistake - i didn't copied that desired rom into updater directory - that was why were all fields N/A... did that, flashed on first try, without problem
I had the same problem, orginal rom from the provider, and I can reflash it again.....
THX for the info......
ROM verion and link location
Hi lobiik,
which ROM did you use for your device, as you comments above:
"i didn't copied that desired rom into updater directory "
can you please point me to location where i can get the ROM, also proper steps to install the same.
Thanks,
Ajay
HELP!!!!!!!!
I tried flash my G3 with shelltools the program said it worked well i did hard reset then i turned it on it is stuck on 1st front screen bootloader mode is stuck i dont know what is is my device bricked
---------------------edit--------------------------
im a newbie
Ok Guys, gonna test all you senior moderators / users here and put you to challenge to see if you can help me get my wizard G4 back up and running.
For the past couple of days Ive been faffng about the forums looking for a way to change my g4 WM5 to WM6, after digging in i realised i had to install vmware and put xp on it, so far so good.
After that ive tried every rom (with all their own prepackaged files) and got nowhere, every time i managed to get one that would even get to a percentage bar screen it would go to 100%, restart and nothing changed. I even tried the all new soft spl way but got some error msg saying a .exe was missing.
tonight, i managed to get a ´302´ error and its now stuck on the bootloader screen, my question is:
how can i ´flash´back to normal state from here , doesnt the pda have to be synced in order to flash it again
I hang my head in shame, i managed to mess it up real this time..
My pda rests in your hand gents. id appreciate the help
Thanks.
IPL : 2.17.0001
SPL : 2.17.0001
GSM: 2.17.1
seems like ur on G4 CID LOCKED and u try to flash with RUU "NO WAY BRO "
flash ur official rom 1st using RUU while on bootloader then flash any G4 safe rom using :
ShellTool
http://forum.xda-developers.com/showthread.php?t=293480
or
SoftSPL
http://forum.xda-developers.com/showthread.php?t=329147
i hope i helped
didnt work, thanks though
thanks for the tip, i tried it and
with soft spl:
when i ran START-sSPL.exe it opens up in cmd and the progress at the bottom doesnt go anywhere but 0.
and shell tools managed to get al the way untill you press OK, when decides to crach..every time.
again, i thought in order to flash these devices to have to have an active sync. but you cant sync things when its showing the red-green-blue bootloader screen...or am i missing something.
more tips are VERY welcome, thanks lads.
PS sorry for being such a noob, pdas are a new thing to me Ñ= and this ones only 2 weeks old for me
shelltool doesn`t crash it hangs only just wait for 30-40 min and unplug ur device and hard reset it will work
aslo on the bottom of bootloader screen u will find USB that means that its connected and it can sync
ill try it.
yeahi seen the usb writing, ok.
ill leave it for 30-40 mins and see what happens, thanks alot for your help so far!
TroXX said:
yeahi seen the usb writing, ok.
ill leave it for 30-40 mins and see what happens, thanks alot for your help so far!
Click to expand...
Click to collapse
u can`t flash with shelltool on bootloader mode but u can flash ur official rom using RUU on bootloader
ok here is what u need to do
1- flash ur official rom or "wizard love rom " using RUU in bootloader mode "RUU works under XP only "
2-after flashing ur stock rom flash and u got up and running OS flash using shelltool "works fine under vista "
uhh..
i downloaded the wizard_love rom, it got to 99% then i got the same 302 error message, theres asmallrecovery process you can go though if this is the case. i followed that and the power went off...hopefully its just the battery...
8125 G4 softspl + flash success!
I just went through the same situation with my phone:
Cingular 8125 G4
IPL: 2.25.0001
SPL: 2.25.0001
GSM: 2.25.11
After a failed unlock attempt/flash, I flashed back using the WizardLove rom to get it functioning, then I used the SoftSPL flash to then allow me to upgrade to Octaivoi 5.0 rom.
Octaivoi's 5.0 *running 12+ hours flawless*
http://forum.xda-developers.com/showthread.php?t=323485
See links in profile.....its all there.
@Trox: Try following this tutorial:
http://forum.xda-developers.com/showthread.php?t=298613
getting somewhere
hey guys thanks for all the help so far.
recently ive been stuck trying to flash the wizard love rom onto my G4, but today i finally cracked it. For some random reason, the phone didnt like the original wizard love rom described in vippies tutorial ( which i looked at , at the very start, a kick ass tutorial bth), i even went out and bought a new usb cable just incase it on the off chance it was that, nope. I kept getting 2 different error messages do to with the connection. 630 i believe was one of them (which is just a general connection error msg).
but today, after searching for a while i found a customised wizard love rom on a bittorrent site that worked like a charm. so im alln gear´d up with a working pda again ! woohoo
So im back to phase one....phasetwo...get wm6 on it or probably break it again for another 3 weeks in the process.
wish me luck !
lol
Nah, i took your adivce and tried to flash that octavia rom onto it...
back to the good old red green and blue screen except this time it doesnt display RUU at the top right hand side anymore...im pretty sure thats a bad thing?
woot!
woot woot!
lots of tinkering over the last few days has proven successful.
ive went from having a non working 9100, and trying hard to find a base rom that would flash properly to:
Finding a wizard_love rom and installing it
managing to use soft spl (which god knows why decided to work after the gizillionth time) and flashing a very respectable wm6 rom to it ( Octaivo, thanks for the tip johngalt82)
And..AND!! even getting the HTC_Touch_ Home_Plugin displaying wonderfully
happy as a pig in ****.
for now...
next task : touchflo
elhamy said:
u can`t flash with shelltool on bootloader mode but u can flash ur official rom using RUU on bootloader
ok here is what u need to do
1- flash ur official rom or "wizard love rom " using RUU in bootloader mode "RUU works under XP only "
2-after flashing ur stock rom flash and u got up and running OS flash using shelltool "works fine under vista "
Click to expand...
Click to collapse
Elhamy, I do owe you the best thanks...
I ruined my KJam for the last week and you really helped in getting my life back
thanks man
Hello, I am a rookie in equipment from HTC, as well buy a HTC X7500, and then tried to put a 6.1 ROM, however some unknown parameters with the SPL, and tried to install a ROM with SPL 3.5, not anything wrong with the equipment when they turn opens a black screen with white and blue list and some red letters ....
Then I tried to access the bootloader, and everything well, he accessed without problems, but when I try to install a ROM it comes to 1% and equipment shuts down, already researched and I am very tired of trying things and nothing result, someone can help me?
When the ROM update process shuts down at 1%, you should be receiving an error message, either an Invalid Device ID error or a communications error. It is possible that your device is not yet properly SIM/CID unlocked. In any event, try to download and install a original OEM ROM (not a custom ROM) and you should be able to recover your device.
If you want to try again to unlock and load custom ROMs, a bit more reading is recommended.
Thanks but managed to solve my problem with this post:
http://forum.xda-developers.com/showthread.php?t=405814
who has the same problem that you can do this work.
i tried to update the rom on my phone but its gone very badly
1st off now when i turn my phone on i get the red green blue and white screen
it says
Niki100
SPL-1.16.0000
CPLD-4
Also has RUUNBH in the top of the screen cannot find a working rom to flash my device with as the ones ive tried end up giving me a 260 error
Thankyou in advance
If ROM has not been unlocked, then you will need to find and flash the original ROM or another from your phone provider.
If ROM has been unlocked, flash any of the official WWE 6.1 ROM. Download a fresh copy, in case the first download was corrupt.
Hope this works
Thanks rling so far i managed to search the internet for an original Orange Dual touch UK (niki100) rom and it found one on this site.
Heres the rom im trying now - http://forum.xda-developers.com/showthread.php?t=364465
so far at 62% and going good
Thank god that restored the phone back to factory settings
stasis-666 said:
Thank god that restored the phone back to factory settings
Click to expand...
Click to collapse
Good.
Now, if you are feeling adventurous , now you can try:
1) Unlocking the phone
2) Flash HardSPL to protect the bootloader of phone
3) Trying different ROMS and radios.
rling,
sry for that question but, what radio do?
I already flash my phone, several times, did hardSPL and everything. but, only folowing tutorials, I never understood in deed why.
If u have time and patience, would you explain in simple words to me?]
Tks and regards.
Hi dumolina, I don't think rling still reads this posts because he switched from device, about the radio's you can find all the info HERE
Greetz,