I don't know why I use HTC_Uni_SIM_Unlock_v1 with my phone !!!!
Now I can,t use IT. During the boot stops same seconds after the windowsmobile screen. It's impossible to contact it.
Read "Problem 5: Device shows NO GSM when booting" on the Common Upgrading Problems in HTC Hermes" wiki page. Solution is there for you
Maybe we should post a warning along with the Universal SIM Unlock tool instructions... such as
DON'T EVEN THINK ABOUT USING THIS WITH A HERMES!!!!!!!
There seems to be at least a couple of new victims every week!
I follow solution n°5 but I have a broblem with the bootloader. The Buttons are correct ?
Thanks
domomedia5 said:
I follow solution n°5 but I have a broblem with the bootloader. The Buttons are correct ?
Click to expand...
Click to collapse
Yes: SIDE OK + POWER + STYLUS RESET
I not be able to connect via USB the phone ! The radio rom 1.20.31.10 don't recognize my phone
http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms
is this the correct rom
thanks
Yes, this is the correct rom:
If you get a "ERROR 120: COUNTRY ID ERROR", do not disconnect the device, run MaUpgradeUt_noID again.
when I arrive to the window from ver. to ver. there are no description of the version !
what can I do
No problem, this is normal it is because the device is in bootloader mode.
how many minutes I had to wait
no more than 30min
It's stop from 30 minutes on cheching information on your device !?!?!
If the Hermes screen shows "Upgrade Radio Stack Please wait........." just wait until it finishes, if not, reset your device and put it back in bootloader mode, and run MaUpgradeUt_NoID again.
Make sure you've previously run the 'erase' commands in mtty sucessfully:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
If you can not success with radio upgrade, do a full rom upgrade using a rom matching your CID, start the upgrade from bootloader and make sure usb connections in activesync is disabled.
Related
Apparently, I'm pretty stupid.
I just got the Cingular 8525; I have spent two hours on this site.
Things I've noticed:
One page says go into bootloader; one page says not to allow usb connections.
I do not know if I am supposed to have my non-Cingular SIM card already in the phone when attempting to do anything.
I have seen connect via USB and use mtty (with what settings do I use when I click on USB from the dropdown menu (if any) and do I connect with mtty via USB in bootloader or when the phone has booted into Windows 5.0 and again what about the non-Cingular SIM card?).
I have flashed my computers BIOS several times but I do not understand how to flash this phone based on the myriad of instructions all over this site (and RFTW did not help which is why I am here with 40000000 questions).
The steps to go from SPL 1.06 to an unlocked SIM/CID phone are?
Things I do understand:
I have SPL 1.06 (I know this from bootloader).
I must downgrade to 1.04 from 1.06 then run the upgrade to 1.06 from the Hermes Upgrade wiki page (I already downloaded all of the Cingular files).
Thanks in advance for any clarification.
I unlocked my 8525 last week, I had bootloader 1.06 so I downgraded to a ROM with boetloader 1.04(you can find it here http://wiki.xda-developers.com/index.php?pagename=Hermes_Upgrades ).. then just follow the instructions in the zip file you downloaded(i used HERM_Unlock_v2a), which are:
1. Enter bootloader mode on your Phone. To do this, simultaneously hold side OK and POWER buttons together and reset with stylus.
[You should see SPL-1.04 on the top of the tri-color screen, if you see SPL-1.06 this unlocker will not work, please wait for the next version]
2. Connect your phone to your computer using the USB lead.
3. Run the MaUpgradeUt_noID.exe program – this will reflash your phone with a patched radio ROM required to unlock.
4. Wait patiently.
5. Once the MaUpgradeUt_noID.exe upgrade completes, it will end up saying "Upgrade Error 114", but the patched radio ROM will be flashed anyway, dont worry about that error!
6. Soft reset with stylus (Device will not be hard reset and no data will be lost)
7. Allow your phone to reboot. Once it has, connect to your PC using Activesync, and copy the HERM_Unlock_v2a.exe program onto your phone. Alternatively, copy it to an SD card and insert into your phone.
8. Run HERM_Unlock_v2a.exe on your phone. Wait about 1 minute.
9. You should see a "SUCCESS!" message from HERM_Unlock_v2a.exe, after that soft reset your phone.
10. Process is (hopefully) complete!
11. If the phone requests unlock code when you put a locked SIM, the code is: 22051978
I assume I want go to 1.04 for Cingular which is 1.30.502.1.
What about my SIM card? Is it supposed to be in phone when I run this file? (it's a t-mobile sim).
I assume the activesync connection via usb is okay? I cannot get it to connect (even though the phone is on and booted into Windows 5.0); is this because I have not inserted the SIM card into the phone? Note: after I unplugged the device, setting allow USB connections on the device in the ActiveSync settings, then plugging it back in, it connected via USB in ActiveSync (4.2). However, I just got a box saying the version of ActiveSync is not compatible with this mobile device. This occured after I started the installer and it showing Verifying the information on your PDA phone.
I received an update error 260 since it thinks the phone is not connected via USB (and I noticed the ActiveSync icon in the system tray is gone).
I went to check the M$ page to see if there is a later download; there is not. Then, the AS icon return (trying to update outlook, install nero mobile) so I decided to run the installer again and now sees my current version 1.34.502.1 and I have the option to upgrade ROM
MilanoRex said:
I unlocked my 8525 last week, I had bootloader 1.06 so I downgraded to a ROM with boetloader 1.04(you can find it here http://wiki.xda-developers.com/index.php?pagename=Hermes_Upgrades ).. then just follow the instructions in the zip file you downloaded(i used HERM_Unlock_v2a), which are:
1. Enter bootloader mode on your Phone. To do this, simultaneously hold side OK and POWER buttons together and reset with stylus.
[You should see SPL-1.04 on the top of the tri-color screen, if you see SPL-1.06 this unlocker will not work, please wait for the next version]
2. Connect your phone to your computer using the USB lead.
3. Run the MaUpgradeUt_noID.exe program – this will reflash your phone with a patched radio ROM required to unlock.
4. Wait patiently.
5. Once the MaUpgradeUt_noID.exe upgrade completes, it will end up saying "Upgrade Error 114", but the patched radio ROM will be flashed anyway, dont worry about that error!
6. Soft reset with stylus (Device will not be hard reset and no data will be lost)
7. Allow your phone to reboot. Once it has, connect to your PC using Activesync, and copy the HERM_Unlock_v2a.exe program onto your phone. Alternatively, copy it to an SD card and insert into your phone.
8. Run HERM_Unlock_v2a.exe on your phone. Wait about 1 minute.
9. You should see a "SUCCESS!" message from HERM_Unlock_v2a.exe, after that soft reset your phone.
10. Process is (hopefully) complete!
11. If the phone requests unlock code when you put a locked SIM, the code is: 22051978
Click to expand...
Click to collapse
crazyut said:
I assume I want go to 1.04 for Cingular which is 1.30.502.1.
Click to expand...
Click to collapse
right
crazyut said:
What about my SIM card? Is it supposed to be in phone when I run this file? (it's a t-mobile sim).
Click to expand...
Click to collapse
doesn't matter
crazyut said:
I assume the activesync connection via usb is okay?
Click to expand...
Click to collapse
It is ok, but generally it causes more problems than it helps. Best is to disable the checkbox that says "enable usb connections" on activesync settings and you'll see the icon on the system tray turn gray with a red "X". Then you need to start the RUU when the device is in bootloader mode (tri-color screen). After you have upgrded the rom (or radio rom) you can reenable activesync again if you want.
crazyut said:
I cannot get it to connect (even though the phone is on and booted into Windows 5.0); is this because I have not inserted the SIM card into the phone?
Click to expand...
Click to collapse
SIM card and activesync have nothing to do.
crazyut said:
I received an update error 260 since it thinks the phone is not connected via USB (and I noticed the ActiveSync icon in the system tray is gone).
Click to expand...
Click to collapse
Icon was gone because RUU checks your current rom version using activesync and then kills it an put device in bootloaer mode. If RUU cannot kill activesync correctly errors happen:
You will avoid the 260 error if you disable usb connections on desktop activesync as I told you, and start the upgrade in bootloader mode... only difference you'll notice is that RUU will not report your current rom version.
Hey. I left the RUU software running (the 25+ minute variety) while I went to buy a case and care charger. I came back and evidently, the phone had rebooted because, it is at the Windows Mobile screen to setup the Windows Mobile device. I assume it is safe to do the 2a software. After that, am I able to update the RUU back to 1.06?
Thanks for your help, Milan and pof!
I rebooted into bootloader to confirm successful downgrade to 1.04 from 1.06 and it was. The RUU software from the upgrade page for Cingular appears to have been successful.
I am now going to attempt the 2a software.
Yes, now follow all the instructions on sim&cid unlocker v2a, and when finished, flash the cingular 1.34 rom again.
pof said:
Yes, now follow all the instructions on sim&cid unlocker v2a, and when finished, flash the cingular 1.34 rom again.
Click to expand...
Click to collapse
It's now on the upgrade screen to Radio 1.16.00.69 but it does not show the previous version. Is this normal? I have not pressed upgrade yet. I have the splitter with the AC and USB cables into the phone (currently in bootloader mode at SPL-1.04).
yes, it is normal... i told you before:
pof said:
RUU checks your current rom version using activesync
[...]
start the upgrade in bootloader mode... only difference you'll notice is that RUU will not report your current rom version.
Click to expand...
Click to collapse
pof said:
yes, it is normal... i told you before:
Click to expand...
Click to collapse
I got the 114 error as promised in the readme. I exited the program using the EXIT button.
The next step:
6. Soft reset with stylus (Device will not be hard reset and no data will be lost)
On the phone display, it still shows Upgrade Radio Stack Please Wait..
The soft reset is the simultaneous OK and Power?
I just took the battery out and reset; it appeared to go okay. I copied the exe file to the phone and was able to run the file as in the readme. I then reset the phone, put in the t-mobile sim and it works.
Thanks much to POF and Milan for their straightforward approach. You can use this thread as a tutorial!
Is there any reason I should add the 1.06 file back to the unlocked 8525?
SPL 1.06 to SPL 1.04 back to SPL 1.06?
Hi:
I followed pof's (with pof's help) tutorial on how to unlock the Cingular 8525. I am currently at SPL 1.04 (downgraded form SPL 1.06) and had run the v2a software to unlock. It works great with T-mobile (I was a Cingular customer but made the switch).
My questions are:
Is there any reason to go back SPL 1.06?
If I do go back to SPL 1.06, it does not affect the unlock status of the SIM or CID?
I still am confused about the Radio and what that does in relation to the CID, SIM, or phone. I assume the Radio is affected the SPL version that you have?
I have tried to peruse through various pages regarding downgrading (the 13 page thread for example) to see if that question is answered.
The radio ROM controls the GSM/GPRS/UMTS hardware in your hermes. You cannot independently upgrade it unless you are running SPL 1.04. There is no reason IMO to go to any other bootloader version.
Sleuth255 said:
The radio ROM controls the GSM/GPRS/UMTS hardware in your hermes. You cannot independently upgrade it unless you are running SPL 1.04. There is no reason IMO to go to any other bootloader version.
Click to expand...
Click to collapse
Oh okay, that clears up yet something else I did not understand
Thanks for the tip on the bootloader version; I will leave it at SPL 1.04.
That being said, I am currently in the middle of the Radio 1.20 thread; I have not finished reading it yet (I can only do so much at work before people wonder what I am doing). Have you upgraded to Radio 1.20? If not, what radio are you running and what do you think of its stability and/or functionality?
Thanks!
I'm running the 1.20 radio. It and the 1.35 TyTN ROM are the best combination I've used so far.
Ok...I have been through all the posts about upgrading etc. I still have a problem and I'm sure that I'm overlooking something....but I can't figure it out on my own. Here is what is happening (it does the same thing with every RUU that I've used...the DST fix...upgrading to WM6....etc)
1. I run the RUU and let it go through its routine (extract files, verify info on pc, etc.)
2. I check the box that says I have read the readme and click next
3. The next screen appears and it has the following steps:
Connect to the USB cable (check)
Establish an ActiveSync Connection (check)
Disable standby and hibernation on PC (check)
Make sure batter is > 50% (check)
Then I check the box and click next
4. I pick the update and click on the update button
5. I verify that I want to upgrade my phone from ROM verion x.xx.xxx to x.xx.xxx and click next
6. The program tells me that I am finally ready to update...and if I am sure I want to proceed to click next...so I click next
7. As soon as I click next...the progress bar comes up on my pc and my phone goes into standby mode (no bootloader...just standby). The progress bar never moves.
8. After a minute or two the RUU give me the ERROR [260]: Connection
9. I reboot my device and repeat steps 1-8
10. I reboot my device and my computer and repeat steps 1 - 8.
Now if I leave my device connected to the usb and close out the RUU after it gives me the ERROR [260], and then run the RUU again...when it is first verifying the information on my pc (before it asks any questions and before it tells me to connect my device) it will throw the device into bootloader mode. If I try to keep running the RUU while the device is in bootloader mode it give me the error that my device is not connected. I have tried and tried...maybe one of ya'll can help me. Thanks in advance
Chris
Some questions:
.) Is your desktop PC running XP or Vista?
If you have a firewall running, close it.
.) If you running Vista check this guide:
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=23&Itemid=27
.) What updates did you try to flash?
.) Did you install Olipros bootloader first?
gerald_s said:
Some questions:
.) Is your desktop PC running XP or Vista?
If you have a firewall running, close it.
.) If you running Vista check this guide:
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=23&Itemid=27
.) What updates did you try to flash?
.) Did you install Olipros bootloader first?
Click to expand...
Click to collapse
XP
No firewall
I tried to flash the WM6 from AT&T I assume its beta
and no did not install the Olipros bootloader
Ok...I think I found out how to do this...Ya'll can tell me if I'm screwing something up.
I go through all the steps listed above until it gets to the progress screen. When it gets there I manually put the the device in bootloader mode (Power, side ok, and reset). Once I do this...the progress bar starts moving. I will let you know if this works...
Hmmmm
Its not the way it should work but if it works its ok
You should have installed Olipros HardSPL first and then try to flash an official rom. If its working then something with your download is wrong.
What ROM is on there now?
Has the phone been CID unlocked?
Oli's CustomRUU is better, you may want to unpack the ROM and put the NBH in a folder with Oli's RUU and then do the upgrade.
BTW, gerald_s is right, you should not have to do that... what you may want to do is put the phone in Bootloader mode manually (while not connected to the PC), then plug in the USB, then start the RUU. That helps some people with 260 error.
I've got the same damn issue... it's driving me crazy. I had this occur when I flashed my Hermes100 from the stock version to Custel's. After about 15 starts and reboots it took. I'm now trying to get to Vp3G's 3.60 and it continues to give me the 260 error.
I am trying to figure out how to fomat my micro, but really hoping to find a solution over cable.
Hermes 100
IPL 1.04
SPL - 2.10 Olipro
Any suggestions?
You may be trying to flash a rom that includes the radio rom. What is your device? Is it possible that your device is a new x01ht with radio 1.14 and radio bootloader 0182? If yes, then you will get this error when you try to flash a rom with this method because during the flash it will be disconnected by the radio bootloader because it is not overwriteable. If you flash using the NBH file on the microSD, it will skip past radio and radio boot and just flash the other parts of the file.
mikebraeuer said:
I've got the same damn issue... it's driving me crazy. I had this occur when I flashed my Hermes100 from the stock version to Custel's. After about 15 starts and reboots it took. I'm now trying to get to Vp3G's 3.60 and it continues to give me the 260 error.
I am trying to figure out how to fomat my micro, but really hoping to find a solution over cable.
Hermes 100
IPL 1.04
SPL - 2.10 Olipro
Any suggestions?
Click to expand...
Click to collapse
If you are running windows XP, just connect the card to the computer, open MY COMPUTER, right-click the removable disk that is your microSD and then click format. Default in windows xp is to format using FAT32 filesystem which is perfect.
The thing is... if you dont know how to format a drive in Windows, should you be flashing your device yourself?
Which Solution???
I've got a Softbank X01HT with:
S/N: HT639
SuperCID <--- result of checking by mtty
IPL: 1.04
SPL: 2.10Olipro
GSM: 1.47.00.10
OS: 3.54.07 WWE
I tried to flash with new Schap 3.54c but the process would not be done coz ERROR 262 or ERROR 302. Fortunately, after failure of flashing, my device is still normal running. Then I tried to flash radio 1.51.00.10 but I got the same above. Once again, I have just tried to flash splash screen and I got the same result too. It mean my device can not upgrade anything !
Anybody here show me a solution that help my device to become a normal device, I mean it will be able to flash anything ROM as it would be! Don't tell me READ and READ, I had read so much . And don't tell me use MTTY again SPL1.01MFG, I think that is a final solution
Wantoknow said:
I've got a Softbank X01HT with:
S/N: HT639
SuperCID <--- result of checking by mtty
IPL: 1.04
SPL: 2.10Olipro
GSM: 1.47.00.10
OS: 3.54.07 WWE
I tried to flash with new Schap 3.54c but the process would not be done coz ERROR 262 or ERROR 302. Fortunately, after failure of flashing, my device is still normal running. Then I tried to flash radio 1.51.00.10 but I got the same above. Once again, I have just tried to flash splash screen and I got the same result too. It mean my device can not upgrade anything !
Anybody here show me a solution that help my device to become a normal device, I mean it will be able to flash anything ROM as it would be! Don't tell me READ and READ, I had read so much . And don't tell me use MTTY again SPL1.01MFG, I think that is a final solution
Click to expand...
Click to collapse
Have you tried flashing with your microSD?
Kevbodian said:
Have you tried flashing with your microSD?
Click to expand...
Click to collapse
I forgot to tell that, I had flashed through extra memory card yet, and could be done!
But I wanna flash ROM against CustomRUU through MS Active Sync as I had used before. Can you help me
i have a problem very similar to Chris. when i check the box "yes activesync is syncronised", and then the progressbar shows up and the phone goes into standby.
i've turned standby of in powermanagement options.
my os is XP
i use active sync v4.5
and this is first time i try this.
i've read something about this bootloader, i can get there but then i cannot sync with active sync. so i kinda stuck.
have been searching the forums and this was the same problem as mine but i don't understand your solutions.
//KufrA
--Problem solved--
i did all things without activesync,
1. start phone in bootloader
2. do the install
3. wait 0% to 100%, and done.
is there a problem with active sync or why do i have to do anything with it at all?
I need some expert help please! I have a Hermes (Orange SPV M3100) that I want to flash with a custom ROM but I am having a problem with ActiveSync losing the USB connection at the point that the device enters the bootloader screen. I am also unable to flash using the SD card method. I have flashed a Nike without any problems and I'm usually good with technical stuff so I think there must be something extra I need to do that I have missed. I hope that somebody can spare the time to help me solve the problem. Here are the details:-
I am trying to follow Mr Vanxs guide to flashing the ROM in windows Vista so that I can upgrade it from WM5 to WM6 and apply a custom ROM to load a new TouchFlo style OS. The first step in this process is to flash HardSPL using this guide but my problem with the USB connection won't let me do that. I have unlocked the device using Hermes Unlocker 3a so it is (or should be) SIM and CID unlocked and be SuperCID with HardSPL-1.40 (so maybe I can miss the Mr Vanxs HardSPL step?).
So, when I run the RUUWrapper.exe, choosing the Force option and accepting the messages I eventually get a prompt on the device. At this stage ActiveSync is connected. I click Yes on the device and it enters the bootloader screen which shows 'USB' on the tri-color screen but ActiveSync immediately drops the USB connection. The update then waits for a while then fails with Error 260. I have to do a soft reset to get the device out of the bootloader screen. When the device reboots the Activesync connection comes back to life.
I thought that I maybe don't need to HardSPL first so I tried just going straight to the ROM upgrade but I get the same problem.
Also, I tried following this link to flash using the SD card instead of USB but when I get to step 6 I don't see a confirm message - just the usual bootloader screen (it doesn't help that the screen shot doesn't appear on the link so I'm not even sure if I'm getting the correct screen). Any ideas?
I realise that an answer to this probably already exists somewhere on the forum but I have spent hours trawling through posts and I can't find it so I hope somebody has come across this before and can help me out.
Thanks guys!
Don't worry I solved it by rebooting my PC, skipping the HardSPL and flashing with an official ROM (HTC_TyTN_WWE_3.54.255.3_6275_1.48.00.10_108). I can now apply custom ROMs.
well, Hard-SPL is released now! sorry for delay, I got distracted elsewhere
[size=+2]NOTE: This is NOT a SIM unlocker - it also doesn't unlock Security for other radios. if you need that, GO HERE[/size]
[size=+2]Donations are always appreciated to the big link in our signature ("elite project"). You can also donate via the link offered in the new Hard-SPL program. Thank you!![/size]
Preparations:
first an important note, if you want to flash more than one Iolite, contact cmonex for additional licenses via http://support.htc-unlocks.com. (the first license is transparently granted and free, so normal users do not need to worry.)
0) this package is for Iolite (Touch Cruise II/2009) devices. for any IOLI***** so far (SSPL loader checks this and gives a warning if needed), afaik there is no CDMA version so all the model variations should be fine.
1) if you have vista, WMDC update is recommended: http://www.microsoft.com/windowsmobile/en-us/help/synchronize/device-center.mspx
Instructions:
read this if unsure how to install Hard-SPL...
1) download latest Hard-SPL package (currently v1.10) from attachment, extract to an empty folder.
2) you must Have Phone Synced with PC in Windows Mobile!!!
3) NEW: internet access is required as the program checks online for updates and license.
4) run Iolite-Hard-SPL EXE on PC, make sure it's launched from a local drive (not through network drive, etc.). if you are on vista, launching as Administrator is strongly recommended, on XP administrator login is required. important: if your AV (norton/symantec mainly) warns about a virus, ignore it, it just doesn't like the packer I used to pack the program.
5) if possible, always use Automatic flash mode (for uses of Manual mode, see troubleshooting section)
6) it will ask you to wait while it prepares for the flashing, press OK. follow steps in the program and then in the RUU.
7) some notes: it should go through without any error messages, if one does pop up, then please follow the instructions included in the error text. if no specific instruction is shown, then ask for help in the thread, but this should not ever occur (as this means a really fatal error occurred).
more notes: when RUU says it will hard reset, do not worry, it is not going to do that. also when it says the flash will take 10 minutes, ignore that, it will only take a minute or so.
8) device should go to a tricolour screen now that says 1.09.C-SSPL, this is the SSPL version, which is temporary.
9) SPL flashes, device automatically reboots, job done.
10) to confirm you got it installed, go into bootloader mode (tricolour screen!) and verify the screen shows 1.09.OliNex, which is the Hard-SPL version.
NOTE: you will not see the SPL version during normal boot, that is the OS version, not SPL!
to enter SPL to check version, fully power the device off by long press of power key, then power on while holding the "volume down" key on the left side of the device. keep holding the volume down key until you see tricolour screen which is the bootloader mode, then release it.
NOTE 2: this is unsigned Hard-SPL. no limitations on flashing ROMs or radio packages. also, this has overwrite protection against HTC RUU's overwriting HSPL with a stock one, so if someone needs to revert to stock SPL for warranty reasons, a stock SPL downgrade package will soon be posted in this post as well. use this relocker *only* if you need to return the phone for warranty, and only use it as last step - after reflashing stock OS and radio. see steps at the end of this post about how to reflash stock SPL.
NOTE 3: do not use this RUU for anything other than SPL flashing (i.e. hardspl or stock spl restore)!!! nothing other than SPL's made by Olinex team (using OliNex custom cert, which is not public) will flash to make SSPL more secure. if you want to flash some other rom, then use shipped RUU or customRUU if you need to flash cooked ROM.
Troubleshooting:
- read the instructions above.
- read the instructions above.
- read the instructions above.
Manual flash mode for USB issues: you should usually go for Automatic flash mode; you must only attempt the Manual mode option if Automatic flash mode or SSPL-Manual.exe already put device in SSPL tricolour screen and you got USB issues. any other errors triggered while running in Autoflash mode will have to be fixed as instructed in the error message.
ModelID checking:
- afaik no CDMA model, so doesn't matter but let me know if you got any problems.
nothing happens on the device, does not enter tricolour screen mode:
- anyone having problems with the device entering SSPL automatically, please make sure you watch the device screen if it asks about running files. also try unchecking advanced usb functionality in settings.
- if it crashes instead of entering SSPL, you need to use Automatic mode.
general usb connection error problems if you get connection error in RUU after the device goes to 1.09.C-SSPL screen:
- try manual SSPL: copy SSPL-Manual-Iolite exe to the device and run it, then when it went to 1.09.C-SSPL tricolour screen and shows "USB" at the bottom in this screen, use Manual option in the Hard-SPL program on the PC.
- make sure device was still synced via USB to the PC at the point of it entering SSPL (the 1.09.C-SSPL screen)!
- try a different USB port
- try different USB cable
- do not touch USB cable during the process especially if it is already a bit dodgy
- also do not use USB hub
- you can also try rebooting your PC
- and you can try using another PC.
- also you can try unticking advanced network functionality in start menu / settings / connections / usbtopc applet.
- another reason for USB connection error: if your PC takes too long to load the drivers (if your device is in bootloader for the first time and perhaps if you are on vista), then if RUU times out, but device still says "USB" on the tricolour screen, just leave it there and re-run the RUU when driver installation finishes.
- finally, you can try disabling antivirus or firewall programs on the PC.
other issues:
- if Enterbootloader.exe fails to run (says missing component or similar), try a hard reset of the device.
- if device reboots instead of going to SSPL screen (1.09.C-SSPL), contact us by PM'ing cmonex. do not PM OliNex user, that is not monitored frequently.
How to reflash Stock/Shipped SPL - STEP BY STEP - FOR WARRANTY REASONS ONLY!:
0. please make sure you already flashed stock ROM and radio, because stock SPL flash is *always* the last step before sending the device in.
1. take the SPL relocker attachment, and run the EXE - this will flash 1.09.0000 stock SPL. simple as that!
2. flash
3. verify if it flashed by checking version in tricolour screen, it should say 1.09.0000.
credits:
first, "OliNex" is a team which means: cmonex + Olipro
Olipro -> EXE program concept that runs on the PC, Hard-SPL concept, server code, maintaining licenses
cmonex -> new PC EXE & SSPL loader for windows mobile and SSPL binary. Hard-SPL binary. (SSPL loader: partially based on haret and old pof&Olipro jumpspl code)
---reserved post---
---reserved---
"IOLI100
SPL-1.09.oliNex
MicroP-Iolite(LED) v5"?
Has it released? It has appeared on the interenet.
Let me see see!
chenjun_conan said:
"IOLI100
SPL-1.09.oliNex
MicroP-Iolite(LED) v5"?
Has it released? It has appeared on the interenet.
Click to expand...
Click to collapse
yes, I've sent it to several people. I'm posting it here too in a sec.
edit: posted
Dan
OK
you are great.
Thank you so much.
Fantastish!
THANK U VERY VERY MUCH!!!
after HSPL and flashing to Rissian ROM it says "Your OS ROM isn' t customized for your hardware Please reflash the proper ROM code or contact the service center' .
In the internet i've read that taking out the battery for 10-15 minutes must help. But it doesn't. Please help!
Great job, big thanks!
@ cmonex was send you a PM, please answer me. Thanks!
Greetings
Baga12 said:
after HSPL and flashing to Rissian ROM it says "Your OS ROM isn' t customized for your hardware Please reflash the proper ROM code or contact the service center' .
In the internet i've read that taking out the battery for 10-15 minutes must help. But it doesn't. Please help!
Click to expand...
Click to collapse
try to flash WWE|Eng and post result here
Nice work as usual guys.
Thread stuck
Dave
After IoliteSPLRelocker, the HSPL' s not working, why? Please help
Thank you
Thank you so much for your hard work.
My Iolite can do do just about anything right now.
Baga12 said:
After IoliteSPLRelocker, the HSPL' s not working, why? Please help
Click to expand...
Click to collapse
You tell us? It what way doesn't it work?
Dave
I tried to test the IoliteSPLRelocker, it flashed correctly, then I again tried to flash the HSPL with mhile my device was in three color mode, but it stops at the 0%, not going more. Stupid of me, of course
So? what about WWE Roms? Does anybody flash them at new HSPL?
thanks very much . it's great'
Baga12 said:
I tried to test the IoliteSPLRelocker, it flashed correctly, then I again tried to flash the HSPL with mhile my device was in three color mode, but it stops at the 0%, not going more. Stupid of me, of course
Click to expand...
Click to collapse
Please help!
max_nya said:
So? what about WWE Roms? Does anybody flash them at new HSPL?
Click to expand...
Click to collapse
Once you have Hard SPL, you can flash any ROM's (Cooked or Shipped) to your device. So put on Hard SPL, find a WWE ROM and flash it .
Baga12 said:
Please help!
Click to expand...
Click to collapse
I've just checked the re-locked and it does contain the correct SPL.
Connect your phone to you PC using AS, and then run the re-locked, once done your SPL should be 1.09 (with the .OliNex) again
Dave
Hi all. please dont flame me or tell me to RTFM i have used the search button and still not found the answer.
im trying to upgrade a htc x7500 from wm6.1 to 6.5 however every upgrade i try i get unit reboots to bootloader and starts the progress bar but as soon as it gets to 1 % i get curropt file error. (this is with every firmware update i have tried). i also have tried to use the SPLDOWNGRADER and i get the same problem at step one.
here is my details:-
spl-1.10
athe100
ipl-v1.00
O/S WM6.1
Cheers
Doesn't sound like its fully unlocked yet. Find the unlocker (around here somewhere) and follow all of its steps again.
hvc123 said:
Hi all. please dont flame me or tell me to RTFM i have used the search button and still not found the answer.
im trying to upgrade a htc x7500 from wm6.1 to 6.5 however every upgrade i try i get unit reboots to bootloader and starts the progress bar but as soon as it gets to 1 % i get curropt file error. (this is with every firmware update i have tried). i also have tried to use the SPLDOWNGRADER and i get the same problem at step one.
here is my details:-
spl-1.10
athe100
ipl-v1.00
O/S WM6.1
Cheers
Click to expand...
Click to collapse
As technetrek said you need to unlock which will change the spl to 1.2
read this thread
http://forum.xda-developers.com/showthread.php?t=429013
yer like i said i get tthe same error trying this unlocker.
step 1 FLASH SPL
i click the flash button and up pops the rom update utility, so i continue Rand press next next next . says verifing tells me the new version so then i press update then next. the image version i have is 2.21.405.2 and the new image to be flashed is Radio-patched. i press next next and get a screen that says its gunna take 10 mins. pda does not reboot and i am connected via activesync.
so that failed.
step 2 UNLOCK RADIO
it sends the file to the unit no problem, i tick sim unlock and cid unlock click go
yer like i said i get tthe same error trying this unlocker.
step 1 FLASH SPL
i click the flash button and up pops the rom update utility, so i continue Rand press next next next . says verifing tells me the new version so then i press update then next. the image version i have is 2.21.405.2 and the new image to be flashed is Radio-patched. i press next next and get a screen that says its gunna take 10 mins. software cannot connect to the pda and it does not reboot to the bootloader and i am connected via activesync.
so that failed.
step 2 UNLOCK RADIO
it sends the file to the unit no problem, i tick sim unlock and cid unlock click go and after a while i get the ""success" windwos.
obviously this is not going to work becasue step 1 faild. click ok
STEP 3 no point itf step 1 failed.
OK
you must remove your sim and sd card
There is a guide in the AP4 thread that walks you through the similar process
It basically ensures that you have loaded all the drivers to successfuly upgrade/ unlock the phone
here it is
http://www.htc-hackers.com/uploads/AP4_How_To_1.8.pdf
edit :i suspect ther is a problem with enablerapi so try the advice above
thanks AP4 worked a treat now using wm6.5