Hi,
First time : i'm sorry for my bad english,
I try a radio corrupt (not for my hermes-probably for 900). I would like change the corrupt radio. I try radio 1.16 but my hermes wait 30 minutes and my pc write "checking the information ..." and nothing.
In bootloader i can see :
Herm200
IPL.-1.01
and
Herm299
SPL-1.04
After change the first corrupt radio, I have a white screen and nothing .
I would like to put the original radio.
My Hermes is a SFR Wodafone 1605.
Thank you for you help
Sincerly,
YC
See "Problem 5: Device shows NO GSM when booting" on this wiki page:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
Re
Ok prof ! I'se a good article :
"If you feel brave, and always at your own risk, what you should do to fix your bricked hermes with screwed radio is this:
1) Put your Hermes in bootloader mode
2) Disable USB connections in ActiveSync
3) Open mtty.exe and select USB port, then connect.
4) Hit enter twice, you will see the "USB>" prompt.
5) Type the following commands (do not copy paste!!!):
Code:
set 1e 1
erase a0040000 c80000
erase a0cc0000 c80000
erase a1940000 640000
set 1e 06) Reset your phone and put it back in bootloader mode
But 1 question :
How i can find a topic to make a rom without activsync
Thanks
Related
Hi
I have problem with unlock my pocket qtek 2020.
Radio 1.17
d 1.72.00WE
How can I do it ?
Greetings from Warsaw )
Where did you find that upgrade with 1.17 radio version? Where i can download?
Thank You
I buy new phone with new software and I can`t unlocking my mda
Greetings from Warsaw
can you post a copy to the forum?
to make a copy of your radio rom, do the following:
( you will lose all data on your device, and your sd-card, so make a backup first )
- make sure there is no sd-card in your device.
- boot your device into bootloader mode
( by holding down the big action button together with the power button,
and hard-resetting with the pen at the same time )
now the display should say 'serial' and the bootloader version.
- insert a blank sd-card
- put your device in it's cradle
- start 'mtty' ( see this page )
- select 'usb' in the mtty program.
- type the followint command into the mtty window
Code:
d2s 60000000 00300000
( this will write your radio rom to the sd-card )
- when it says it is done, remove the sd-card.
- hard-reset, and reinitialize your device.
- put it in the cradle again.
- insert the sd-card, answer 'no' to the do-you want to format question.
- use 'psdread' to copy the sdcard image to a file ( you type this command on a windows or dos command prompt )
Code:
psdread -3 0 0x300200 sdradio.img
see here for information on psdread.
correction: I meant 'psdread'.
now put this howto up on the wiki
Hello,
i try to flash bootloader 1.01 mfg according to http://wiki.xda-developers.com/index.php?pagename=Hermes_BootloaderMFG
It hangs after
USB> lnbs SPL-1.01.nbs 50020000
...
start NB image download
According to other threads this behavior exists if mtty can not find the file. But the file is in the same directory as mtty.
Does anybody has an idea what is wrong?
Thanks
Andreas
did you do the "Task 32" first? and if you did did you get "Level = 00"
yes, but i only one 0
USB>task 32
Level = 0
USB> lnbs SPL-1.01.nbs 50020000
i got some output at this point, but i cannot remember exactly
???
? 50020000
? 00000000
????
The last line was: start NB image download
My device is SuperCID. SPL 1.09
there's your problem then; you need SPL-1.04.
I suggest you load Hard-SPL and try again...
also, might I heartily recommend that instead you download my MFG pack and use SSPL with 1.01 rather than flash it to your device... or at least use my patched 1.01 (create an NBH)
I get that message whenever I do not type the name of the file correctly, like for example, sp1-1.01.nbs instead of spL-1.01.nbs (the latter being the correct spelling). Just my two cents..
I had 1.09 before, coz I updated with full RUU versions of roms (like 2.06.502.3 cingy or 2.05.255.1 HTC), and I had no problem to downgrade to 1.01 MFG and now to 1.01 oli... I also used mtty, device was supercid, used commands was
USB>task 32
Level = 0
USB> lnbs SPL-1.01.nbs 50020000
USB> task 8
If I remember correctly, task 8 automatically SW reset herm... maybe I am lucky one?
take a look at your mtty icon. Does it say MFC or does it look like a serial connector. If it says MFC then you have the wrong version of mtty.
my guess: it says "MFC"
Thanks for all your answers. At the moment a'm at work and cannot try your suggestions.
But i have some further questions:
>olipro: there's your problem then; you need SPL-1.04.
According to the wiki:
"This is a very special bootloader which can be flashed in any bootloader version BUT to flash it your Hermes must be SuperCID first..."
...can be flashed in any bootloader... what does this mean? i thougt i can flash it from 1.09. sinmae was able to do it. (or did i miss something)
>crazyut: wrong file name
i checked this several times. i typed the right name, but i do not now whats the working directory of mtty. i put the nb-file in the same directory as mtty and startet mtty from a dos-prompt. so this should be ok.
>Sleuth255: wrong version of mtty
i tried to investigate this yesterday. somebody said he has version 1.11a. i have version 0.01. it says MFS. so this should be the problem. but this is the version from the wiki:
http://wiki.xda-developers.com/index.php?pagename=Hermes_BootLoader
http://wiki.xda-developers.com/uploads/mtty.exe
where can i get the right version? (at google i found mttty (3 t))
Thank
Andreas
Use the mtty.exe included in this pack, mtty and nbs file in the same dir.
I can't flash SPL 1.04 over mtty.
Code:
USB>
USB>task 32
Level = 0
USB>lnb SPL-1.04.nb 50020000
Command error !!!
USB>
What is the problem?
igord said:
I can't flash SPL 1.04 over mtty.
Code:
USB>
USB>task 32
Level = 0
USB>lnb SPL-1.04.nb 50020000
Command error !!!
USB>
What is the problem?
Click to expand...
Click to collapse
PLEASE tell me why you are trying to do this outdated DANGEROUS operation??
Download duttys nbh tool, pack the .nb file into an RUU and do it using safe SSPL........messing with mtty can be a risky business.
Hi.
my phone mtty conection is not working...
When the mtty is open the only thing i see is: CLIENTCLIENTCLIENT
So, untill i get this thing working i can't try any more updates to bring alive my RADIO!!!
can anyone help me to configure the phone, or the MTTY?
THANXS!
cauboi25 said:
Hi.
my phone mtty conection is not working...
When the mtty is open the only thing i see is: CLIENTCLIENTCLIENT
So, untill i get this thing working i can't try any more updates to bring alive my RADIO!!!
can anyone help me to configure the phone, or the MTTY?
THANXS!
Click to expand...
Click to collapse
Did you disable Active Sync USB?
Yes, many times i check and unchek the "Allow USB..."
Which SPL do you have?
hi, my phone is:
At&t 8525
IPL 1.04
SPL 2.30
Radio (unknown, i don't remember but i gues it will be the orginal 1.54)
ROM 2.15.502.3 (04/09/07)
Thank you for reading!
You can't use MTTY with SPL 2.30, you need SPL 1.04, SPL 1.06 (no rtask command), but the best SPL to use with MTTY is 1.04.
igord said:
I can't flash SPL 1.04 over mtty.
Code:
USB>
USB>task 32
Level = 0
USB>lnb SPL-1.04.nb 50020000
Command error !!!
USB>
What is the problem?
Click to expand...
Click to collapse
you should flash SPL With RUU;MTTY command work with SPl. so the MTTY commands different form different SPL
Version.
Ok guys,
i think i'm in a sort of big trouble. I got SPL1.2, i was installing this Miky ROM and then at 91% Windows Mobile Device Center crashed on my pc. Now what i have is a 7500 booting with strange lines on the screen and then fading to white. I tried to pull out the battery and then to recover but nothing is working. I broke my 7500??? Why God is never here when i need him???
See if you can get into bootloader (tri color screen) if you can flash a factory rom. Have a look here, you should find what you need or a link to the needed resources http://forum.xda-developers.com/showthread.php?t=429013
Cheers
BR
***Why You Try This !!!___carefully step by step !!!!!!!!
cmonex
Senior Member Join Date: Jul 2006
Location: Budapest
Posts: 2,314
--------------------------------------------------------------------------------
here's an experimental program I made to make the process more automatic so users can fix their own wifi without our help.
this is good for both corrupt modelid and corrupt wifi, and fixes both at the same time.
STEP BY STEP:
1. download attachment at the end of the post for mac1.exe (requires .net 2.0 installed on the PC)
2. you will also need to download the other attachment in this post for the mtty program.
3. enter bootloader (tricolour screen) manually by pressing and holding camera button all the way in (yes I mean that, press it in as hard as you can!!), while doing a reset, then keep the camera button held until you see the tricolour screen.
4. disable USB in activesync (wmdc if you have vista - in this case, do not kill wmdc, just disable usb in it!!!)
5. run mtty and select USB option from the dropdown box!
6. then press enter in main window that comes up, see if that gives you Cmd>
7. now you should have Cmd>, if not, re-check if you did the above steps right until you get Cmd>
8. now run the mac1.exe, type in your MAC address you want to use for the Athena, if you have SPL 3.xx reported on the tricolour screen, then use the button for SPL 3.xx, otherwise if you have SPL 1.xx reported, use button for 1.xx.
9. this should have generated a .bin file for you, copy that bin file in the folder of mtty.
10. now, in mtty, type (do not copypaste!) this command: task 32
11. this should return Level = 0
12. now, you must only do one of the two following commands:
- if you have SPL 3.xx, then type (do not copypaste!!) this command: lnb filename.bin 76508000
(there filename is the name of the .bin file you generated - don't forget to put .bin after filename, as the full name is needed).
- OR, if you have SPL 1.xx, then the command is different (do not copypaste!!): lnbs filename.bin 75108000
(there filename is the name of the .bin file you generated - don't forget to put .bin after filename, as the full name is needed).
NOTE, the command starts with a lowercase "L", not "I"!
WARNING: PLEASE DO NOT MIX UP THESE TWO DIFFERENT COMMANDS!!!
if this info helps: most people will have SPL 3.xx, and if you have AP4 (not vanilla) already running then you're definitely 3.xx
13. mtty will popup a window asking "OK", you press OK!
if you get "Fail to synchronize with the host (1)", then make sure you did follow step by step. if still same error, try placing mtty and the bin file under C:\.
14. now the file downloads, if mtty reports it flashed the file, and at the end "code entrypoint unknown", then that's it, now boot back to WM and see if wifi works.
edit: see raskell's mtty tutorial too, #36. post in this thread
if you *really* can't manage to get it working, you can still feel free to PM me.
let me know if this program and step by step description helped any.
Attached Files mac1.zip (6.3 KB, 1585 views)
mtty_0513_Test.zip (553.9 KB, 1883 views)
__________________
Here is direct link__on floor #33 ===>
http://forum.xda-developers.com/showthread.php?t=387454&highlight=mtty&page=4
Good Luck!!!
Hello
Please help me return the model number,
cause when I try to change my rom I always get the same error Error [244] : Invalid model id.
Now I have
some strange symbols in bootloader.
This appeared after I'd tryed to change mac using mtty, as I have created bin file for SPL 1.xx
Please help me
Hi,
You need to carry out the instructions to the letter in post 33 HERE and it will sort your problem, read it all very careful, its easy to make a mistake if you're not paying attention.
regards
Jay
Thanks Jay.
It works again.
You're welcome, glad it helped
Regards
Jay
here's an experimental program I made to make the process more automatic so users can fix their own wifi without our help.
this is good for both corrupt modelid and corrupt wifi, and fixes both at the same time.
STEP BY STEP:
1. download attachment at the end of the post for mac1.exe (requires .net 2.0 installed on the PC)
2. you will also need to download the other attachment in this post for the mtty program.
3. enter bootloader (tricolour screen) manually by pressing and holding camera button all the way in (yes I mean that, press it in as hard as you can!!), while doing a reset, then keep the camera button held until you see the tricolour screen.
4. disable USB in activesync (wmdc if you have vista - in this case, do not kill wmdc, just disable usb in it!!!)
5. run mtty and select USB option from the dropdown box!
6. then press enter in main window that comes up, see if that gives you Cmd>
7. now you should have Cmd>, if not, re-check if you did the above steps right until you get Cmd>
8. now run the mac1.exe, type in your MAC address you want to use for the Athena, if you have SPL 3.xx reported on the tricolour screen, then use the button for SPL 3.xx, otherwise if you have SPL 1.xx reported, use button for 1.xx.
9. this should have generated a .bin file for you, copy that bin file in the folder of mtty.
10. now, in mtty, type (do not copypaste!) this command: task 32
11. this should return Level = 0
12. now, you must only do one of the two following commands:
- if you have SPL 3.xx, then type (do not copypaste!!) this command: lnb filename.bin 76508000
(there filename is the name of the .bin file you generated - don't forget to put .bin after filename, as the full name is needed).
- OR, if you have SPL 1.xx, then the command is different (do not copypaste!!): lnbs filename.bin 75108000
(there filename is the name of the .bin file you generated - don't forget to put .bin after filename, as the full name is needed).
NOTE, the command starts with a lowercase "L", not "I"!
WARNING: PLEASE DO NOT MIX UP THESE TWO DIFFERENT COMMANDS!!!
if this info helps: most people will have SPL 3.xx, and if you have AP4 (not vanilla) already running then you're definitely 3.xx
13. mtty will popup a window asking "OK", you press OK!
if you get "Fail to synchronize with the host (1)", then make sure you did follow step by step. if still same error, try placing mtty and the bin file under C:\.
14. now the file downloads, if mtty reports it flashed the file, and at the end "code entrypoint unknown", then that's it, now boot back to WM and see if wifi works.
edit: see raskell's mtty tutorial too, #36. post in this thread
if you *really* can't manage to get it working, you can still feel free to PM me.
let me know if this program and step by step description helped any.
Attached Files
File Type: zip mac1.zip (6.3 KB, 2125 views)
File Type: zip mtty_0513_Test.zip (553.9 KB, 2613 views)
Ameo
Pfff i have tried everthing what i could find and nothing works. i managed to get the driver working from usb on windows 7 but it keeps showing the bootloader! with some strange marks. i flashed it with 1.2 Olipro and im afraid it will never work again any suggestions left?
Greetings