Hi,
First time : i'm sorry for my bad english,
I try a radio corrupt (not for my hermes-probably for 900). I would like change the corrupt radio. I try radio 1.16 but my hermes wait 30 minutes and my pc write "checking the information ..." and nothing.
In bootloader i can see :
Herm200
IPL.-1.01
and
Herm299
SPL-1.04
After change the first corrupt radio, I have a white screen and nothing .
I would like to put the original radio.
My Hermes is a SFR Wodafone 1605.
Thank you for you help
Sincerly,
YC
See "Problem 5: Device shows NO GSM when booting" on this wiki page:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
Re
Ok prof ! I'se a good article :
"If you feel brave, and always at your own risk, what you should do to fix your bricked hermes with screwed radio is this:
1) Put your Hermes in bootloader mode
2) Disable USB connections in ActiveSync
3) Open mtty.exe and select USB port, then connect.
4) Hit enter twice, you will see the "USB>" prompt.
5) Type the following commands (do not copy paste!!!):
Code:
set 1e 1
erase a0040000 c80000
erase a0cc0000 c80000
erase a1940000 640000
set 1e 06) Reset your phone and put it back in bootloader mode
But 1 question :
How i can find a topic to make a rom without activsync
Thanks
Hello,
i try to flash bootloader 1.01 mfg according to http://wiki.xda-developers.com/index.php?pagename=Hermes_BootloaderMFG
It hangs after
USB> lnbs SPL-1.01.nbs 50020000
...
start NB image download
According to other threads this behavior exists if mtty can not find the file. But the file is in the same directory as mtty.
Does anybody has an idea what is wrong?
Thanks
Andreas
did you do the "Task 32" first? and if you did did you get "Level = 00"
yes, but i only one 0
USB>task 32
Level = 0
USB> lnbs SPL-1.01.nbs 50020000
i got some output at this point, but i cannot remember exactly
???
? 50020000
? 00000000
????
The last line was: start NB image download
My device is SuperCID. SPL 1.09
there's your problem then; you need SPL-1.04.
I suggest you load Hard-SPL and try again...
also, might I heartily recommend that instead you download my MFG pack and use SSPL with 1.01 rather than flash it to your device... or at least use my patched 1.01 (create an NBH)
I get that message whenever I do not type the name of the file correctly, like for example, sp1-1.01.nbs instead of spL-1.01.nbs (the latter being the correct spelling). Just my two cents..
I had 1.09 before, coz I updated with full RUU versions of roms (like 2.06.502.3 cingy or 2.05.255.1 HTC), and I had no problem to downgrade to 1.01 MFG and now to 1.01 oli... I also used mtty, device was supercid, used commands was
USB>task 32
Level = 0
USB> lnbs SPL-1.01.nbs 50020000
USB> task 8
If I remember correctly, task 8 automatically SW reset herm... maybe I am lucky one?
take a look at your mtty icon. Does it say MFC or does it look like a serial connector. If it says MFC then you have the wrong version of mtty.
my guess: it says "MFC"
Thanks for all your answers. At the moment a'm at work and cannot try your suggestions.
But i have some further questions:
>olipro: there's your problem then; you need SPL-1.04.
According to the wiki:
"This is a very special bootloader which can be flashed in any bootloader version BUT to flash it your Hermes must be SuperCID first..."
...can be flashed in any bootloader... what does this mean? i thougt i can flash it from 1.09. sinmae was able to do it. (or did i miss something)
>crazyut: wrong file name
i checked this several times. i typed the right name, but i do not now whats the working directory of mtty. i put the nb-file in the same directory as mtty and startet mtty from a dos-prompt. so this should be ok.
>Sleuth255: wrong version of mtty
i tried to investigate this yesterday. somebody said he has version 1.11a. i have version 0.01. it says MFS. so this should be the problem. but this is the version from the wiki:
http://wiki.xda-developers.com/index.php?pagename=Hermes_BootLoader
http://wiki.xda-developers.com/uploads/mtty.exe
where can i get the right version? (at google i found mttty (3 t))
Thank
Andreas
Use the mtty.exe included in this pack, mtty and nbs file in the same dir.
Dear All,
Could someone please tell me how to get the SPL back to original
my jasjam
HERM100
IPL-1.00
SPL-2.10.OLipro
I try to use spl-1.01MFG_Pack.zip to flashing of unsigned code via the 'lnb'"
Cmd>task 32
Level = 0
Cmd>lnbs spl-1.01.nbs 50020000
:F=spl-1.01.nbs
:A=50020000
:O=00000000
:L=FFFFFFFF
start NB image downloadSH
Load ADDR: 50020000 Length: 402C4
***
SPL flag is incorrect, please check your SPL is correct.
Write NAND error, addr=0x50020000
Error !! The image must be in ROM area.
what should i do to reflash original SPL over SPL2.10.Olipro?
try following this exactly, worked for me.
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=59&Itemid=27
Cmd> lnbs SPL-1.01.nbs 50020000
:F=SPL-1.01.nbs
:A=50020000
:O=00000000
:L=FFFFFFFF
start NB image downloadS
Load ADDR: 50020000 Length: 402C4
H***
SPL flag is incorrect, please check your SPL is correct.
Write NAND error, addr=0x50020000
Error !! The image must be in ROM area.
BTW
I want to update my sys to WM6.1
What does this mean?
I wanna to change my spl to 1.01
my herm200
IPL-1.04
SPL*2.01.olipro
I am being online to wait your answers
thanks
hi there folks! sadly i got a failure at attempting flashin my niki htc touch dual:
original tri color (boot)screen read:
niki 100
spl 1.16.0000
cpld-4
M04 R 1.58.16.27
B04 G25.61.30.03H
D 1.31
image version 1.31.61.10
1st step:
downloaded and run sspl 1.16 on to my device(niki)
boot screen showed:
niki 100
sspl 1.16.jump
cpld-4
2nd step:
downloaded and executed nikicustomRUU.exe "step 1" flash froze at 95%
error read:
Extracting EnterBootloader.exe
Extracting ErrorBattery.fig
Extracting ErrorUSB.fig
Extracting ModelID.fig
Cannot create ModelID.fig
Extracting Temp.bat
Extracting rapitool.exe
Extracting ROMUpdateUtility.exe
Cannot create ROMUpdateUtility.exe
Extracting RUUGetInfo.exe
Extracting RUUResource.dll
Cannot create RUUResource.dll
//
flash recovery methods used with no solution:
tried HARDboot>reeboot to original manufacturer settings FAILED!
boot screen tri color reading:
(top right)RUUNBH
(left side screen) niki100
spl 1.16.0000
cpld-4
dwnld and run MTTY 1.16 ver
follow instruction and reads:
0x73db6c2c8 ref. memory 0x00040406 memory cannot read! FAILED!
...ANY SUGGESTIONS????
best regards!
thnx!!!