Related
@all
anyone have a solution on how to downgrade rom..
i have a ATOM and upgraded to ATOM EXEC rom..
theres some guide in here but its inside of other thread and its not working..
please help us..i know im not the only one have a problem like this..
thanks in advance..
-=[serialzs]=-
If you have Atom Exec ROM, then the bootloader keys are Camera+Reset. If you can enter bootloader, you can now upgrade to the usual XDA Atom ROM.
Cheers,
Jiggs
jiggs said:
If you have Atom Exec ROM, then the bootloader keys are Camera+Reset. If you can enter bootloader, you can now upgrade to the usual XDA Atom ROM.
Cheers,
Jiggs
Click to expand...
Click to collapse
where i can put the bootloader? can you help me? please..
-=[serialzs]=-
serialzs said:
where i can put the bootloader? can you help me? please..
-=[serialzs]=-
Click to expand...
Click to collapse
press camera+reset button. you should see bootloader screen. From here, upgrade using the procedure I discussed in the aku3.3 thread.
cheers,
Jiggs
thanks for the help but i figure it out on my own now..i done it with something i dont think earlier because im too excited..hehe..
now i have a atom rom back again..
i will guide people have same problem..hope i can help..
-=[serialzs]=-
o2 atom upgrade problem
hi
i need ur help
i have o2 atom i upgrade to exec now i can not go back
it give me error in connection
please help
all_brother2002 said:
hi
i need ur help
i have o2 atom i upgrade to exec now i can not go back
it give me error in connection
please help
Click to expand...
Click to collapse
what version of atom exec you use?
-=[serialzs]=-
Well, I managed to downgrade my ROM back to the original Atom (my sig isn't updated - had problems with the extROM wiping itself) - but I was kinda lucky.
Y'see, the AE hack rom I use has an updated bootloader that won't let you do a USB firmware update unless you're activesync'd.
The only way to solve an ExtROM wipe was to reflash the device, so I did. Using the hack ROM DSUU - at this point, the original ROM won't recognize the device - I found that it usually takes a few tries for the extROM update to go through (extROM format fail) - when it fails, your phone will be stuck in bootloader (Connect a USB cable). Repeated attempts to flash the phone solves the problem.
So when my extROM inevitably disappeared again, and I hit the extROM format fail again, I decided I had enough and tried using the original Atom0426-0822 ROM.
It went through this time.
Seems that the only way to bypass the bootloader lock is to semi-brick your device. >_>
Just a question to all of you who are more experienced than me
I want to change my atom exec wwe to cht, can anyone tell me how to bypass the device country id error. do i use an spl? and are these spl programs device specific? or do i use the bootloader mode? Can someone explain that to me?
Thanks all in advance.
Bootloader mode works as long as you aren't using the Atom Exec hacked ROM (bootloader will tell you to use Async if you try). To upgrade, go into the bootloader, connect via USB, and run the DSUU from the computer.
You know you did it correctly when your unit's current firmware information is read as "0" by the DSUU/
Ultimate Chicken said:
Bootloader mode works as long as you aren't using the Atom Exec hacked ROM (bootloader will tell you to use Async if you try). To upgrade, go into the bootloader, connect via USB, and run the DSUU from the computer.
You know you did it correctly when your unit's current firmware information is read as "0" by the DSUU/
Click to expand...
Click to collapse
Strange, i already did that, and got the "0" from DSUU, but when i start upgrading, the bootloader spits out a message saying that i should connect with OS mode.
Anyway, I've edited the diskimage_Ver.nb0 file to do it.
Hi,
I have the same problem :
- bootloader : ok
- firmware 0 : ok
but connection error !
Do you have an idea ?
Thanks a lot.
bedav said:
Hi,
I have the same problem :
- bootloader : ok
- firmware 0 : ok
but connection error !
Do you have an idea ?
Thanks a lot.
Click to expand...
Click to collapse
Hi guy the main key on the file call EBOOT everytime when you want dowgrade your OS to normal ATOM just put this file to you SD card then use the bootloader mode you can see "imge downloading" just wait for a second it will reboot again . then you can use the DSU mode to flash your device
thats work !
Thank you very much !
HELP on my atom exec
w/o reading, i downgraded my atom exec to atom...
hw can i bring back my atom exec default WM5 ROM?...
am planning to upgrde to WM6 aftr...
hi
i updated my atom rom version to 3.3.3 three days ago.It installed completed i used this rom 3-4 hours then i was freeze and i try to reset it. it didnt respond so i decided to hard reset to my atom.I tried to hard reset now it says "device clean boot....." it stuck this screen then i try to reset the device then it stuck o2 screen it didnt pass to align screen. i cant use my atom for three days
Please help me......
remove the battery for a while.. then try hard reset / reflash
i try this method but it is same it doesnt work
did u try the instructions posted in aku 3.3.3.??..
"
For those of you who have downloaded and flashed using SD Card method who ended up in a brick! ITEX recovers his Atom by following procedure:
1. remove SD Card
2. remove battery
3. hold camera button and reset (stylus) button
4. replace battery while still holding the buttons
This will bring you back to bootloader mode. Just flash the above DSUU.
"
Does it have a chance to use wm6?
joolawan said:
Does it have a chance to use wm6?
Click to expand...
Click to collapse
it can barely use WM5 and anyway these chinese splash their advertising for WM6 all over the place in hope ppl will buy their rom, until I see it running in my device or get confirmation from someone reliable (such as Jiggs) I dont believe a word of it and besides the 3.3.3 rom is very fast and ten times better than any actual official release
yes i tried to that method too. it is same it still stuck on o2 screen. it doesnt pass to align screen..please help me
my problem didnt solve pls help me i cant use my atom..........
plsssssssss help meeee...........
plsssssssss help meeee...........
R U able to go to bootloader mode ?...
ironeagle said:
R U able to go to bootloader mode ?...
Click to expand...
Click to collapse
try to be on the bootloader and reflashed the ROM. try to search same cases in the forum. I think they solved the problem alike.
yes same to problem. i dont re enter bootloader again :S
did DSUU Recognize your ATOM ?..
Connect your ATOM to PC (using USB)
Run DSUU
Try to flash it..
i can enter bootloader mode and i can update rom but after this proccess it says "device clean boot......" and it freeze . it doesnt pass to align screen
plssss help meeeeeeee.
Which ROM you flashed?..
i flashed orginal atom rom i downloaded from seeo2.com
pls helpppp meeeee my atom is dead
are u using o2 atom exec or just atom?
cuyz i've got o2 atom exec..maybe i could flash it with o2 atom (yeah i cant flash anything with dsuu)
mine is o2 atom
did u amend any thing from the original ROM from seeo2? I mean you flash your atom with the original ROM...0426? without replacing the extended ROM...etc?
...tried to unlockit with the athena-unlocker! After Step 1 it startet to Step2 und suddenly the connection was lost!
Now the battery lamp of the Ameo is in green mode!
I can make a factory reset, but I see no bootloader mode!
Screen is black an a green light aroundthe joystick! The Connection via active sync to my pc isn't available any mory!
What do you think?
game over - any change to bring my Ameo back to life?
Edit1: ther is no MiniSd Card inside
Hi, I do not think your Ameo is lost. Some else hat the same problem, please check http://forum.xda-developers.com/showpost.php?p=1358430&postcount=35 and try the steps described there. In most cases, it is also possible to flash WM6 if your device is stuck in the bootloader.
There are two things I would like you to try:
- To make a Hardreset hold the volume slider down and press the reset button.
- To enter Bootloader press and hold the camera button and press the reset button.
Do any of these work?
If any of these two works, you should be able to flash WM6.
...you were right - thx a lot 4 the solution
stupiddog said:
There are two things I would like you to try:....
- To enter Bootloader press and hold the camera button and press the reset button.
Do any of these work?
If any of these two works, you should be able to flash WM6.
Click to expand...
Click to collapse
At last -
That (your 2nd tipp) was the solution -WM& upgrade is now running on the ameo (now at 5%)!
Thx a lot
Jackpot thx -
Kisses from Austria
Many thx!
utakurt said:
At last -
That (your 2nd tipp) was the solution -WM& upgrade is now running on the ameo (now at 5%)!
Click to expand...
Click to collapse
You're welcome, have fun with WM6 However, if you want to kill the SIM-Lock/Net-Lock on your device, you have to run the unlocker again. It seems that WM5 has some problems running the unlocker while WM6 does not.
After you successfully run the unlocker again, remember to flash your WM6 ROM again (watch the battery power, it should always be >50% before starting flashing!) so you have the newest Radio version.
If problems persist after flashing, this page in the XDA wiki might be helpful: http://wiki.xda-developers.com/inde...e Athena Unlocker - the Black Screen of Death
stupiddog said:
There are two things I would like you to try:
- To make a Hardreset hold the volume slider down and press the reset button.
- To enter Bootloader press and hold the camera button and press the reset button.
Do any of these work?
If any of these two works, you should be able to flash WM6.
Click to expand...
Click to collapse
Hi, mate
Wot if those two things does not work??
i mean
if we can not get into boot loader or hard reset
i have this ameo does not go into boot loader or does not do hardreset
only red light on the joystick
problem occured while unlocking with Olipro, completing step 1 (got stuck at the point of saving the spl file)
thank you very much in advance for your help
BR,
Hi does anyone know if there are WM6 ROMs for the SPV C550 if not are there any good WM5 ones?
look topic about wm5 for hurricane, there are also links to wm6 for hurricane device
hello again
here is latest, almost perfect rom for hurricane:
http://rapidshare.com/files/56833250/566.zip.html
and new SPL for this device:
http://rapidshare.com/files/56616745/spl566wm6_spfans2006.rar
lazaj007 said:
hello again
here is latest, almost perfect rom for hurricane:
http://rapidshare.com/files/56833250/566.zip.html
and new SPL for this device:
http://rapidshare.com/files/56616745/spl566wm6_spfans2006.rar
Click to expand...
Click to collapse
Has anybody tried this ROM?
lazaj007 said:
hello again
here is latest, almost perfect rom for hurricane:
http://rapidshare.com/files/56833250/566.zip.html
and new SPL for this device:
http://rapidshare.com/files/56616745/spl566wm6_spfans2006.rar
Click to expand...
Click to collapse
Ideal thanks
So is the 566.zip the WM5 or WM6 rom and has it been tested?
Whats the new SPL?
hI ALL, can u tell me the mini guide how to install this rom? I did it once to my sda but I dont remember now, where is the nbfupdatetool and RUU and patched RUU..???
when I type l c:\wm6.bin it give me this:
clean up the image temp buffer at 0x8C080000 Length 0x01B00000 MTTYDownloadImageNot allow operation!
Error : DownloadImage return error (code = 0xFFFFFFFF)
cmd>
maybe damaged rom, or any idea?
Gang: Make sure you're CID unlocked. (Eg, when you issue "info 2", it says HTCSuperCID).
How can do that cid unlock? give me some working link to download that tool or something. thx
here you go
http//www.spv-developers.com/content/SPV-Services.zip
you must check "CID Tool (Alpha)" and click set CID=11111111
after this restart your phone
and short solutions about wm6 installing:
* installation is the same like typhoon
-unlock Super CID
-upgrade new SPL (Patched ruu)
-disable USB connection in ActiveSync
-switch off your phone
-press and hold camera button, and put USB cable to your phone
-next check "Y"
-when your phone will be in bootloader mode (tri color screen) run mtty
- check USB connection in this program
and write: - info 2
- format BINFS
- l c:\566.bin (localization of your rom)
after succeful installising reboot your phone and it will be end
rom is very good, baterry work better
hmm, thx for guide, I believe it will work, but I have little problem : now I cant even connect to activesync so I cant do cid unlock, any idea how to fix that
lazaj007 said:
here you go
http//www.spv-developers.com/content/SPV-Services.zip
you must check "CID Tool (Alpha)" and click set CID=11111111
after this restart your phone
and short solutions about wm6 installing:
* installation is the same like typhoon
-unlock Super CID
-upgrade new SPL (Patched ruu)
-disable USB connection in ActiveSync
-switch off your phone
-press and hold camera button, and put USB cable to your phone
-next check "Y"
-when your phone will be in bootloader mode (tri color screen) run mtty
- check USB connection in this program
and write: - info 2
- format BINFS
- l c:\566.bin (localization of your rom)
after succeful installising reboot your phone and it will be end
rom is very good, baterry work better
Click to expand...
Click to collapse
Thanks for helping out!
A few questions?
1. This link "http//www.spv-developers.com/content/SPV-Services.zip" takes me to Wikipedia.
2. Where can I find the patched ruu to update the spl. It wasn't in the zip file?
Thanks in advance!
to Mr MIAGY :
1. just write that link starting with www. (without http//, or type http://)
2. in ''wm6 for c550'' topic u will find patched RUU and all needed files, they are ziped together
gangstaunitg said:
to Mr MIAGY :
1. just write that link starting with www. (without http//, or type http://)
2. in ''wm6 for c550'' topic u will find patched RUU and all needed files, they are ziped together
Click to expand...
Click to collapse
DoH! I didn't notice the missing ":"
Cheers!
Anybody have idea why I cant connect to activesync after spl upgrade ? Before spl upgrade it all goes well. Can I do something with it?
if upgrade was complited succes then you must turn off USB connection in Active sync, then run bootloder mode and do everything with instructions.
I did it !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
THank u all, thankS
This rom is amazing, everything work perfect, and it looks beautiful,
one more time thank you. jUUHHHUUUUUUUUU
lazaj007 said:
if upgrade was complited succes then you must turn off USB connection in Active sync, then run bootloder mode and do everything with instructions.
Click to expand...
Click to collapse
Upgrade reported as success
However after reboot I see the WM6 boot screen - loverly ...
Then the Mobile Operator Splash screen ... THEN
After too long ... the phone switches itself off and I have to take the battery out to get reponse again.
Any ideas?
It's a C550 ....
MrMiyagi said:
Upgrade reported as success
However after reboot I see the WM6 boot screen - loverly ...
Then the Mobile Operator Splash screen ... THEN
After too long ... the phone switches itself off and I have to take the battery out to get reponse again.
Any ideas?
It's a C550 ....
Click to expand...
Click to collapse
Ok, so a report. The phone boots, goes through WM6 splash screen, then operator screen, then APPARENTLY dead black screen.
BUT I plugged in the USB cable and the screen came on! WM6 Setup screen! All good go through setup eveything looks GREAT!
Only problem is, if I leave the phone alone for a bout a minute, the screen goes black AGAIN. Then no amount of key pressing on the device will bring it back to life.
Plugging the USB cable in brings it instantly back to life! But This means I can't wander too far from my PC ;-)
ANY Ideas
BTW IT LOOKS FANTASTIC! If I can just get around this issue ;-)
MrMiyagi said:
Ok, so a report. The phone boots, goes through WM6 splash screen, then operator screen, then APPARENTLY dead black screen.
BUT I plugged in the USB cable and the screen came on! WM6 Setup screen! All good go through setup eveything looks GREAT!
Only problem is, if I leave the phone alone for a bout a minute, the screen goes black AGAIN. Then no amount of key pressing on the device will bring it back to life.
Plugging the USB cable in brings it instantly back to life! But This means I can't wander too far from my PC ;-)
ANY Ideas
BTW IT LOOKS FANTASTIC! If I can just get around this issue ;-)
Click to expand...
Click to collapse
Heh heh ... seems I'm posting to myself ... that's cool I like my own company ... So I reflashed the SPL and some of the problems have gone away.
Phone will boot OK now ... but it will still "go to blank screen" and require plugging into the USB cable to "wake it up"
I'm out of ideas now ...
Hi guys,
Hi,
I'm a hp rw6828 user and is very much enthusiast to try out those wm6 roms made by those experts. However, i did a mistake while trying to flash.
I tried flashing with a rom from wantat but i forgotten to delete the EBOOT.nb0 before i clicked "upgrade". Then the program stopped at 6% for a long time and didnt move. I disconnect the cables and tried to turn the device on.
THe device can go into the wm6 and the start button can be use but the screen is "moved" to the right side and other function is not working.
After that, i did a hard reset and the the os seem to work like normal. However, when i tried to go into bootloader mode by pressing both "_" and soft reset. That didnt work. I tried another way by taking out the batt, leave it for a 10mins, press both "_" and soft reset, put in batt, release soft reset then "_" keys. That didn't work either.
But, just lately, i've tried taking out batt, holding the camera key and softreset, place back batt, release soft reset n camera button. This method works and i get what it seems to be an atom bootloader?
i get a black background with "MN1 Bootloader Mar 29 2006 13;52;14 copyright..... 1) debug module through UART 2) jump to DM Enter your selection.
I've searched the forums and found few ways to downgrade back to wm5 but those aren't the same conditions with what im facing. Can someone recommend how can i downgrade back to wm5 with the conditions that im facing? All you help is much appreciated. THank you.
You are lucky , at lease your device now become atom. My was totally cannot on power and just vibrate. Till I have to sent it back to HP SC and change the main board . Can you understand chinese , if yes than I have a solution you may try . Else you have to wait . I just download a program and doing some testing , the program is in chinese language .
Thx for you reply. I guess u can say that. I'm from msia but cant read chinese.
Is it possible to solve the problem by sending back to hp using warranty claim? I think i still have warranty left but its ending very soon. One more week i think.
elus said:
Thx for you reply. I guess u can say that. I'm from msia but cant read chinese.
Is it possible to solve the problem by sending back to hp using warranty claim? I think i still have warranty left but its ending very soon. One more week i think.
Click to expand...
Click to collapse
I don't think you still can claim under warranty unless you can make your phone total can't on and access to windows mobile. Last time I sent it back they charge me RM 385 to change the main board . I did talk to their technical personal , it seen like they don't know what is bootloader and flash it back to original rom . What they do was just change the main board with preloaded program .
Good luck
If you think that you can claim you warranty , than you just go a head . If not , may be you can access my thread "HP6828 WM6" , download any one of the rom that I post , follow the instruction accept downgrade bootloader . Enter your phone in bootloader mode . If you can start the process , than it will flash a new hp bootloader into your phone .
Against . Good luck
Cheers
I'm from malaysia also.
Ok. I'll try your method to restore the bootloader. Thx for the fast reply. I'll keep u update with the progress. Thx again.
elus said:
Ok. I'll try your method to restore the bootloader. Thx for the fast reply. I'll keep u update with the progress. Thx again.
Click to expand...
Click to collapse
You've flash ATOM Bootloader, there are many ways to restore to HP Bootloader ... don't worry !!!
nhocbanme said:
You've flash ATOM Bootloader, there are many ways to restore to HP Bootloader ... don't worry !!!
Click to expand...
Click to collapse
Can share the information how to restore back the HP original bootloader ? And the procedure . Thanks
First you must have HP bootloader file (Eboot.nb0) 1.01 or 1.05 are OK.
- Use DRUU to restore Bootloader : replace ATOM bootloader file with HP bootloader file
- Use miniSD to restore Bootloader : copy Eboot.nb0 to miniSD card, go to bootloader ... wait 1' it will auto hard reset.
After flash successfull remmember remove Eboot.nb0 from miniSD.
- Reflashing Bootloader using JTAG. (Use only when can't use two above menthods)
HP Bootloader 1.01 : http://rapidshare.com/files/82853862/HP_BL1.0.1.rar
HP Bootloader 1.05 : http://rapidshare.com/files/82853924/HP_BL1.0.5.rar
nhocbanme could you please specify which specfic DRUU should be use for your method? Thank you.
You should use DRUU of Chartreux, replace Eboot.nb0 and choose OS and Eboot
Remember copy a HP68xx ROM (diskimage_Ver.nb0) to C:\Windows\Temp with DRUU of Chartreux then start...
nhocbanme, you explanation seems vague to me. Probably cause im still new. Could you please give a clearer instructions? Thank you
elus said:
nhocbanme, you explanation seems vague to me. Probably cause im still new. Could you please give a clearer instructions? Thank you
Click to expand...
Click to collapse
-You must extract RUU in C:\Windows\Temp (no sub folder) then replace Eboot.nb0 with Hp bootloader 1.01/1.05
-Copy a diskimage_Ver.nb0 (any ROM WM6 for HP 68xx) to C:\Windows\Temp
-Run the DRUU program and choose OS and Eboot and start.
Goodluck !!!
It worked! Thx a lot nhocbanme and wantat. The methods restore the atom bootloader to hp bootloader. The DSUU by chartreux is a good tool.
Now, i would like to put this solution up into the wiki. How may i do so? Thank you.
hi, im william from M'sia. i like to know how you recover your previous installed AtomROm back to WM5.
can u provide some step to step detail
if possible upload some files can let me flash from memory card in the bootloader screen
ur reply are highly appreciated
thx ~~
williamSun said:
hi, im william from M'sia. i like to know how you recover your previous installed AtomROm back to WM5.
can u provide some step to step detail
if possible upload some files can let me flash from memory card in the bootloader screen
ur reply are highly appreciated
thx ~~
Click to expand...
Click to collapse
OK, please read my topic, I'll post a WM5 ROM flash via miniSD
help !!
im facing another problem again...
this time i changed the file extension EBOOT0502_MNT_01.01.03.nbf to EBOOT0502_MNT_01.01.03.nb0
(file from HP official WM5 SP34074, inside the installed folder )
and copy to memory card and put in 6828 then started to go bootloader screen
few minutes later my screen goes blank, and i tried with the revive methods
which is
-press the 2 softkey " - " and reset button
-put in the battery ,
-release reset, then release softkey
but didt work out!!!!no repsponse at all..tried many times..possible dead ad???
plz help me abit ..big troblem!
I dont think i can help u much here as im still new. From the looks of your problem, i guess u forgotten to cut the first 12bits (or something like that) of your bootloader when u use it to flash via mini sd. Maybe you can try the JTAG method mentioned in the atom wiki to restore your bootloader. Good luck.
Thanks guys!
The same exact thing happened to me yesterday..I was already about to sell my ipaq as a dead unit and i came upon this thread and after following the steps it did made ipaq alive again..
thank you very much guys,i hope you continue to help more people..
god bless and best of luck to you
more power xda-dev!