here is what I've done and what happened:
my ROM was HTC 1.18.255.3 07/22/06 with bootloader 1.04 then I ran "HERM_Unlock_v2a.exe" on the device but I didn't use "HTC_Hermes_Radio_for_SIMunlock_v1.16.00.69" to save time and i wanted a CID unlock only.
after "SUCCESS!" message from "HERM_Unlock_v2a.exe", I connected my device via USB to PC and started to upgrade to Cingular 1.31.502.1 08/30/06 with aku 2.6 and bootloader 1.06 but when I get the "ID ERROR",without disconnecting the USB, I switched back to ugrading to previous ROM HTC 1.18.255.3 and the Processe started with no problem untill 98%, then suddenly upgading interrupted a message came saying connection error or somting like that!
since then my device is stuck on windows mobile screen and I've tested solutions in the "Hermes_Upgrade Problems" page and tried using the "Hermes SD Card flashing" method, But It seems impossible to flash my phone agian.
Help me PLEASE,HELP
someone help me please!
POF can't you help me please
I think Pof is away until 3rd december, I have the similiar problems with my second hermes, if you have then use mtty to see if you have an corrupted cid using info 2.
Do you have the original rom to go back on if so that will fix your problem.
I've used mtty to send some commands to my device and it answers to some of them but It just stop responding when I type "info 2" or "info 3".
and i tried this in mtty:
"
USB>checkimage
IPL CRC checksum = 0x9FCC6BEB
SPL CRC checksum = 0x3BF03635
CE CRC checksum = 0xC0E1751A
ExtROM CRC checksum = Total Block= 1024
dwBlockIndex= 1024
Address Error1!!!
Get checksum ERROR!!!
0x0
Radio Image CRC checksum =
"
again It stop responding
also tried upgrading, no matter which ROM I try, it just can't connect to device.
and thanx for your relpy.
hi, since there is NO htc service center available around me I have to do something about it myself but my phone is still dead and I'm using a nokia 1101. PLEASE someone help me, pof are you back? can you help me?
I've tried all in this page:
"http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems"
and this one too:
"http://forum.xda-developers.com/showthread.php?t=280733"
and tested qtek 2020 rom but no use.
from what I've found out my device hang up and stop responding when it gets the "INFO 2" or "INFO 3" or "TASK 32" or perhaps any thing involving CID so no upgrading utility is able to connect to it, the only thing is to connect to it using "mtty.exe" which I've tried any command found here, but no use again.
and my SPL is 1.04
can anyone help me?
mht220 said:
I ran "HERM_Unlock_v2a.exe" on the device but I didn't use "HTC_Hermes_Radio_for_SIMunlock_v1.16.00.69" to save time and i wanted a CID unlock only.
Click to expand...
Click to collapse
Wrong, you also need a patched radio to CID unlock. Running only the exe file without the patched radio has no effect on the unit.
mht220 said:
from what I've found out my device hang up and stop responding when it gets the "INFO 2" or "INFO 3" or "TASK 32" or perhaps any thing involving CID so no upgrading utility is able to connect to it, the only thing is to connect to it using "mtty.exe" which I've tried any command found here, but no use again.
and my SPL is 1.04
Click to expand...
Click to collapse
Please attach usb monitor capture when trying to flash a ROM and a radio ROM. Otherwise can't help you.
here is exported files from usb-monitor:
and tanx for your reply
uuh... there must be something really wrong with it, no response to bootloader commands. If no sd card flashing is possible, I would suggest you to send it to service centre too.
pof said:
...I would suggest you to send it to service centre too.
Click to expand...
Click to collapse
It's a difficult option for me, as I should send it to a foreign country to service center,so are you sure there is no way like erasing somewhere using mtty?
pof said:
... no response to bootloader commands...
Click to expand...
Click to collapse
but it respond to some of them in mtty.exe e.g. "erase", "set" and some other.
pof said:
...If no sd card flashing is possible...
Click to expand...
Click to collapse
no it would stuck in "checking..." forever
tanx
HI,
I have same exactly problem on my spv m3100: since sept06 I've tried every kind of Unlock software,upgrade ROM and method found in xda..In mtty bootloader (spl 1.04) respond at every command but not "info 2","info 3" and "task 32".Sd card method works but if you try to upgrade other ROM,in your screen "loading..." and then "checking..." hangs on because the ROM upgrade must to match CID (I suppose..).I'll wait the next ROM Upgrade and ORANGE won't release it until gen07..
warrio said:
I'll wait the next ROM Upgrade and ORANGE won't release it until gen07.
Click to expand...
Click to collapse
it seems your problem is like mine if so, I don't think ANY normal upgrade can solve your prolem 'cause it can't connect to it.
so don't wait and send your device to service center, if you can.
I'm in your same conditions:there's no repair center here so I have to wait Orange who release a upgrade Rom (I hope asap..).
Related
Please help me!
I screwed my MDA Vario II. I used HTC universal sim unlocker and I haven’t got radio. I know I was a craze.
No GSM, no cid and no imei. The pda is working good.
I vas very happy when I find this site :
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems.
I made this:
USB>
USB>password 0000000000000000
HTCSPass1.CMˆËHTCEUSB>set 1e1
USB>erase a0040000 c80000
HTCST ÚČŇHTCEUSB>erase a0cc0000 c80000
HTCST ÚČŇHTCEUSB>erase a1940000 640000
HTCST ÚČŇHTCEUSB>set 1e 0
USB>
The radio doesn’t work , no GSM, no cid and no imei. The pda is working good.
Please help me
Please can a expert check this!?
I found this with the search option.... can someone check this....
Its written for the Tytn and not for the Vario II, i'm not sure but i thought that the english Vario II has a 1.06 bootloader!! Then you are stuck, beacause the file who degrade your bootloader to 1.04 isnt availleble anymore. Maybe one of the guys here can share it with you?!
======================================================
- Take the battery out of your TyTN and leave it out several minutes
- Disable USB-connection in Active-Sync
- Reboot your Computer
- Replace the battery and put your TyTN in the bootloader
- Try to load the ROM found here:
ftp://xda:[email protected]/RUU120_172125_Qtek_WWE_R11400_Shipping.exe
- Keep trying till you get just past the erasing part, then you will get an error-message and are asked to reset your device with the stylus
- Reset your phone and put it back in the bootloader mode
- Install any Hermes ROM you like, no matter what CID if you have bootloader 1.04
lacika said:
The radio doesn’t work , no GSM, no cid and no imei. The pda is working good.
Click to expand...
Click to collapse
Can you attach a USB monitor capture of what happens when you try to:
a) flash a rom
b) flash a radio rom
Do both things starting from bootloader and with activesync disabled.
Same Problem
I have the same problem
My PDA keeps comming back in the bootloader screen.
When 1 try to update (its a unlockes pda), the upload stops at 1%
Is there a way to erease the PDA ?
Thanks
pimmmm said:
I have the same problem
Click to expand...
Click to collapse
I have the same questions.
Can't do anyithing if you don't attach a USB capture of the process. See this page for instructions: common upgrade problems
smarty77 said:
I found this with the search option.... can someone check this....
Its written for the Tytn and not for the Vario II, i'm not sure but i thought that the english Vario II has a 1.06 bootloader!! Then you are stuck, beacause the file who degrade your bootloader to 1.04 isnt availleble anymore. Maybe one of the guys here can share it with you?!
======================================================
Click to expand...
Click to collapse
HI!
Thank You for your answer. I made yours tip, but not was good.
First I to try smarty77 tip. I used RUU120_172125_Qtek_WWE_R11400_Shipping. Its function. After I’d like rom upgrade. This doesn’t was good (invalid vendor).
Second I to try clearing with mtty.exe.
The situation same, the phone doesn’t work.
Sorry my bad English.
pof said:
Can you attach a USB monitor capture of what happens when you try to:
a) flash a rom
b) flash a radio rom
Do both things starting from bootloader and with activesync disabled.
Click to expand...
Click to collapse
HI!
Thank You for your answer. I made yours tip, but not was good.
First I to try smarty77 tip. I used RUU120_172125_Qtek_WWE_R11400_Shipping. Its function. After I’d like rom upgrade. This doesn’t was good (invalid vendor).
Second I to try clearing with mtty.exe.
The situation same, the phone doesn’t work.
Sorry my bad English.
Just seen your capture but it's not good.. you made a "basic" capture which shows nothing important, please repeat the process again, but this time read point 6:
In the upper part there are two tabs: basic and complete. Click on "Complete".
I cannot help unless I have a complete capture to see the problem.
pof said:
Just seen your capture but it's not good.. you made a "basic" capture which shows nothing important, please repeat the process again, but this time read point 6:
In the upper part there are two tabs: basic and complete. Click on "Complete".
I cannot help unless I have a complete capture to see the problem.
Click to expand...
Click to collapse
HI POF!
Thank you four your help.
It is a new captured files.
Please help me. You are a last chance, for my phones.
Lacika
@lacika:
When checking the seclevel (task 32 bootloader command) your phone replies:
Code:
CID: Wait interpreter timeout.
Level=FF
After that when checking the CID with 'info 2' your phone replies:
Code:
HTCS...?\0.?f..|HTCE
This should be something like T-MOB001 if you have a Vario II from UK, so the CID is screwed.
I can see from the output of 'info 3' that you're running bootloader 1.06.
Then you try to flash the 1.18.255.3 ROM from HTC, which has CID "QTEK_001", you won't be able to flash this image in your device with bootloader 1.06, even if the CID was not screwed you will always get an error (you need bootloader 1.04 to bypass CID checking, and you are in 1.06), the error you're getting from bootloader is:
Code:
CID not allow (255)
As you said you can use the PDA (WinCE boots) what I suggest is buying imei-check unlocker (you need activesync working too for running the imei-check unlocker), because it will downgrade your bootloader to 1.04 and patch your radio... probably it can fix your device, at least it will downgrade your bootloader to 1.04. If after running the unlocker your device doesn't work I suggest that you try to flash a radio ROM, you can find them here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms
Let me know how it goes
pof said:
As you said you can use the PDA (WinCE boots) what I suggest is buying imei-check unlocker (you need activesync working too for running the imei-check unlocker), because it will downgrade your bootloader to 1.04 and patch your radio... probably it can fix your device, at least it will downgrade your bootloader to 1.04.
Click to expand...
Click to collapse
Err... I forgot that your IMEI is also screewed, probably imei-check unlocker will not work on your Hermes even if you provide them the right IMEI, because it will not be able to read the IMEI from your phone (will get the wait interpreter timeout too...). anyway... it costs 20GBP, give it a try!
pof said:
@lacika:
As you said you can use the PDA (WinCE boots) what I suggest is buying imei-check unlocker (you need activesync working too for running the imei-check unlocker), because it will downgrade your bootloader to 1.04 and patch your radio... probably it can fix your device, at least it will downgrade your bootloader to 1.04. If after running the unlocker your device doesn't work I suggest that you try to flash a radio ROM, you can find them here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms
Let me know how it goes
Click to expand...
Click to collapse
Hi and thanks!
I’ve got one question. I use imei-check unlocker after I’ll got 1.04 bootloader?
Lacika
I tried that with my device before it got sent to service, I brought imei-check unlocker but as my imei was also corrupt it will not work, so I would not waste GDP 20 if you have corrupt imei.
They will not refund either becuase its your problem the imei is corrupt.
lacika said:
I use imei-check unlocker after I’ll got 1.04 bootloader?
Click to expand...
Click to collapse
No, imei-check unlocker will downgrade your bootloader, BUT as shark1 says, it will not work because your IMEI is corrupted and it will not be able to read it.
I guess the best would be to send the unit to the repair centre then...
pof said:
@lacika:
As you said you can use the PDA (WinCE boots) what I suggest is buying imei-check unlocker (you need activesync working too for running the imei-check unlocker), because it will downgrade your bootloader to 1.04 and patch your radio... probably it can fix your device, at least it will downgrade your bootloader to 1.04. If after running the unlocker your device doesn't work I suggest that you try to flash a radio ROM, you can find them here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms
Let me know how it goes
Click to expand...
Click to collapse
Hi!
I’ve got a new problem.
I used a M3100v3cUnlock.exe program. This doesen’t read my imei number.
I don’t know how can I flash my bootloader.
Lacika
pof said:
No, imei-check unlocker will downgrade your bootloader, BUT as shark1 says, it will not work because your IMEI is corrupted and it will not be able to read it.
I guess the best would be to send the unit to the repair centre then...
Click to expand...
Click to collapse
I had the same problem! Send it to orange assistance.
lacika said:
I used a M3100v3cUnlock.exe program. This doesen’t read my imei number. I don’t know how can I flash my bootloader.
Click to expand...
Click to collapse
You can't, and your imei is screwed, the unlocker can't check it... so you should better send the unit to the repair centre as suggested.
pof said:
You can't, and your imei is screwed, the unlocker can't check it... so you should better send the unit to the repair centre as suggested.
Click to expand...
Click to collapse
HI!
I’ve got a last question.
It will a new procedure, program, with I can flashing my bootloader.
Lacika
Dear All,
I've tried to upgrade to ROM Hermes_1.18.416.1_1.18.416.101_1.14.00.10_WWE_Ship
and unluckly cable loosen and I reset the phone.
Since it's in the middle and can't success enter the Windows Mobile,
but the bootloader was updated to 1.06.
Now I can't flash any ROM either
HER_DopodAsia_1237074_1060010_WWE_SHIP or the new one.
The tools on "imei check" even can't recognize my phone.
Any one can help me on this issue, please?
Thanks in advance.
Try the steps here, let us know the results:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
If you don't fix it with the proposed solutions attach USB Monitor capture in text format as explained in the bootom of the page.
I have the same issue, and sent it to service, and now I have the phone back and they could not fix it, so got no radio or imei number, so none of the FAQ will work for me.
So I have an expensive paper weight.
Hi,
ME TOO!!
I recently had a power cut (yes, a lights off power cut!) that killed my PC half wat through installing the Cingular English CWS__001 1.34.502.1 09/21/06 ?? 1.16.00.00 32.53.7018.01H 14955.2.3.0 ROM onto my SPV 3100.
Now SPV 3100 will boot to the ROM I was running prior to the upgrade but I can't use the telephone. I'm also not able to rerun the upgrade as it got far enough through the process to upgrade my bootloader to 1.06 - therefor rendering me unable to load another ROM.
Before the crash I was using the Imate ROM as below and M3100 was sim unlocked and running on o2 3G
i-mate English CDL__001 1.20.305.3 07/21/06 1.20.305.104 1.07.03.10 32.41.7010.02H 14955.2.3.0 1.04
I have also tried imei without any joy.
the PDA part of my M3100 still works but the phone is dead. I have been told that if you can get the latest radio installed then you satnd a chance of the phone part working.
We need a hack to get bootloader 1.4 back on the phones.
Please help.
Thanks
My one now is a photo frame which one show "HTC" or "Windows Mobile",
at least your one is a PDA.
There are nothing in "info 2" and so nothing can be flash into it.
Is it possible to have something written CID and IMEI to phone in mtty
and let the flash rom success?
i am in the same situation like yhlee. Pof, i have reply your pm and ready to upload the result file to FTP. where should i upload to?
Thanks
oh i forgot to say, mine is even worst. as soon as i turn on the unit. it will go right into bootloader without press any button.
The USB Log is too large (around 2MB)
and can't upload, any suggestion?
Thanks.
rnc1688 said:
oh i forgot to say, mine is even worst. as soon as i turn on the unit. it will go right into bootloader without press any button.
Click to expand...
Click to collapse
This can be fixed by bootloader commands 'set 14 0' and 'task 8', will reboot your device and boot into OS again (but no GSM yet!)
yhlee said:
The USB Log is too large (around 2MB)
and can't upload, any suggestion?
Click to expand...
Click to collapse
Upload it to xda-developers ftp:
ftp://xdaupload:[email protected]/Uploads/Hermes/
USER: xdaupload
PASS: xda
POF, file have been uploaded, file name= rnc1688
Thanks
'set 14 0' and 'task 8' didn't work
@rnc1688: It starts the flashing process, but you get a "CID not allow (255)" error because your CID is corrupted and you are in bootloader 1.06.
Is not booting WM5 after "set 14 0" in mtty.exe? If it's not booting WM5 you'll not be able to flash bootloader 1.04 and bypass CID checking.
so i guess my unit is bricked now.
I've upload the file which named yhlee.txt.
However, I'm going to send the unit for service.
Hope they can fix.
Any way to make it show the bootloader screen on start-up
everytime?
"set 14 1" doesn't work after push the RESET button.
Thanks.
@yhlee: U're getting exactly the same error as rnc1688. Device in bootloader 1.06 which has corrupted CID, however you say you can go into OS, so it would be possible for you to downgrade the bootloader so it does not enforce CID checking.
yhlee said:
Any way to make it show the bootloader screen on start-up everytime? "set 14 1" doesn't work after push the RESET button.
Click to expand...
Click to collapse
Try "set 1e 1" and then "set 14 1", you'll boot stright into bootloader.
@rnc1688: If you want to go WM5 try this:
"set 1e 1" and then "set 14 0", you should be able to boot stright into OS.
no luck either
grrr!!!... command "set 14 [0|1]" is working fine in 1.04 here to switch boot into WM5 or boot in bootloader mode... probably different in 1.06??? I don't have a 1.06 now to test
Mine one is just showing "Windows Mobile" but stuck there,
but seems rnc1688 one is a PDA but my one is nothing.
I've sent to distributor for service.
Thanks you pof.
yhlee said:
I've sent to distributor for service.
Click to expand...
Click to collapse
Let me know when they fix it... i'm curious about if they will fix it with 1.06 or they will downgrade to 1.04 first.
I got a correct message back from the service company, and they will not fix a bootloader 1.06 unless the original rom has been release with it, I was told that is HTC policy on this.
Hello everybody - can anyone help me at this moment. I am right now sitting with my Hermes connected through USB. I was flashing the standard ROM with RUU_HERMES_HTC_WWE_1[1].35.255.2_1.35.255.102_1.08.00.10_SHIP. Unfortunately it stopped at 5% some half an hour ago. I prefer to ask you before disconnecting it. Please help!!!!!!!!!
OK, having no answer I decided to disconnect it and look for an answer. Now I know that I have a 1000 USD brick and no possibility to put it back to work.
I now suspect that the upgrade did not work properly because my device had a CID lock. That is quite strange however, because I bought it on the open market without any commitment to any GSM operator.
I am now stuck on the tricolor bootloader screen with SPL 1,09.
Basing on the post: http://forum.xda-developers.com/showthread.php?t=285157 - especially on the lines:
"1.09
You can't downgrade to bootloader 1.04 by flashing a Shipped ROM. However imei-check.co.uk is able to downgrade the bootloader.
There was a solution posted on this forum, but it was stolen from imei-check and was removed. If you are not willing to pay you have to wait until another solution is developed.
The RadioROM can't be upgraded. You have to downgrade to bootloader 1.04 to unlock your device.", despite seeing info on the website, I paid to imei-check the 20 pounds.
So far I only lost money, time and nerves trying to downgrade or "repair" my hermes. Nothing works. If anybody has any suggestions please share on the forum or PM me.
BTW I started the whole process with SPL 1,04.
Sounds to me like a flaky USB port which is why it stopped at 5%. Try another port in the rear of your PC and re-flash. Be sure to follow the mantra:
Windows XP, screensaver, powersave disabled
No other programs running.
i had a similar problem probably with the flaky usb port as Sleuth255 mentioned. trying with a different pc is another option if you have one and that was what i did with success.
im not sure about the hermes.. but i know on the wizard as long as you could get to the bootloader screen (the RGB screen) that your device isnt bricked yet.. i would follow the other suggestions about usb ports and using different pc's, i bet you can make your $1k work for you again
Try:
Go into bootloader by pressing down both the POWER button and SIDE OK together and using the stylus at the same time to press the RESET button at the bottom.
Make sure you have disabled the USB connection in ActiveSync, before trying to connect to the bootloader:
File --> Connection settings --> uncheck "allow USB connections"
Connect your USB-Cable
Download mtty.exe. Start it and connect to USB
When you see "USB>" Type "info 2". You should get: "HTCS" + CID + (4-byte checksum) + "HTCE". Remeber what CID you have.
Look for a Shipped ROM that matches your CID
Download and flash it using a different USB-Port or PC than the last time
Afterwards you will be able to use the file that you got from imei-check. The imei-check downgrader/unlocker only works if you've got a working operating system on your device.
After typing "info 2" in mtty.exe I get the following line
HTCSF kEŘ(HTCEUSB>
Which of those is the CID? I cannot find any matching one in the Wiki.
corrupted CID by wrong flash.
OK, I have now the confirmation of the diagnosis - as I was suspecting.
Can I now have some help in the solution?
Some people succeded with the method described as "problem 5" here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
but some others don't succeed and have a brick. Try the steps on the wiki, if you are not able to fix it this way, send it to repair centre.
Following the steps from point 5 of the given website, I only get the following lines:
USB>password 0000000000000000
HTCSPass1.CMˆËHTCEUSB>
USB>set le 1
USB>erase a0040000 c80000
HTCST ÚČŇHTCEUSB>
USB>erase a0cc0000 c80000
HTCST ÚČŇHTCEUSB>
USB>erase a1940000 640000
HTCST ÚČŇHTCEUSB>
USB>set le 0
USB>
Unfortunatelly nothing changes.
I've the same problem. I was flashing the HTC 1.18.416.1 1.18.416.101 1.14.00.10 but the process has stopped to 89 % and now the phone is in bootloader mode spl- 1.06 and don't enter in windows mode !!! My cid is HTCSORANG001a#USB> I hope that i've not a brick !!!
mtadeuszak said:
Following the steps from point 5 of the given website, I only get the following lines:
[...]
Unfortunatelly nothing changes.
Click to expand...
Click to collapse
Your bootloader is 1.09 and you'll not be able to flash anything because the CID will not match. Send it to service centre.
deika95 said:
I've the same problem. I was flashing the HTC 1.18.416.1 1.18.416.101 1.14.00.10 but the process has stopped to 89 % and now the phone is in bootloader mode spl- 1.06 and don't enter in windows mode !!! My cid is HTCSORANG001a#USB> I hope that i've not a brick !!!
Click to expand...
Click to collapse
Your phone is not trashed, but there is no rom matching your CID yet. You should have cid unlocked it before flashing a rom with BL 1.06.
Try to boot OS again using "set 14 0" (see wiki, "problem 4"), if that doesn't fix it (chances are it will not), then wait until orange releases a rom upgrade with CID "ORANG001".
I've try the procedure "Problem 4" but after "write nand success" and sr it don't start. My cid is always ORANG001 with spl-1.06
pof said:
Your bootloader is 1.09 and you'll not be able to flash anything because the CID will not match. Send it to service centre.
Your phone is not trashed, but there is no rom matching your CID yet. You should have cid unlocked it before flashing a rom with BL 1.06.
Try to boot OS again using "set 14 0" (see wiki, "problem 4"), if that doesn't fix it (chances are it will not), then wait until orange releases a rom upgrade with CID "ORANG001".
Click to expand...
Click to collapse
Please Pof try to help me. Where can i find that rom ? Thanks
You can't find it at the moment. It's not released yet
sn00x said:
You can't find it at the moment. It's not released yet
Click to expand...
Click to collapse
But you think that it will be available ? Thanks
Yes it will surely be released I think. But nobody knows when. Perhaps tomorrow, perhaps next year.
It bet it will be listed here when it's available.
I have a bricked Hermes, I am not able to flash it.
Is it possible to flash a hermes, when it starts till the following picture ?
And I have no usb-connection via active sync, only with the Multi-Port TTY.
No I've read that I can flash it in the bootloader-modus with the command "wdatah " ?
So i pu in following:
USB>
USB>password 0000000000000000
HTCSPass1.CMˆËHTCEUSB>
USB>set 1e 1
USB>wdatah HERMIMG.nbh
Invalid parameter number!
USB>
So what is wrong ?
data is sent in blocks, you can't flash with mtty.
and how can I flash ?
I've also tried it with "hermimg.nbh" on the micro-sd card.
But it only shows loading... and then checking ... and nothing more.
Bundy said:
and how can I flash ?
I've also tried it with "hermimg.nbh" on the micro-sd card.
But it only shows loading... and then checking ... and nothing more.
Click to expand...
Click to collapse
first... what bootloader are you running.
secondly... what's wrong with your phone?
....thirdly what were you doing when the phone became faulty?
first ... i have SPL 1.04 and bootloader 107
secondyl... my phone doesn't start - first it looks like a tv with no antenna and with some numbers at the botton - also no gsm
and then i see the blue "windows-mobile" screen.
thirdly - i have flashe my device and since the flashing the hermes doesnt start
I think I've tries everything - but nothing helped
Try to flash HTC 1.18 rom with bootloader 1.04 and run the RUU two times. If this doesn't work try to flash a radio using HERMflasher.
pof said:
Try to flash HTC 1.18 rom with bootloader 1.04 and run the RUU two times. If this doesn't work try to flash a radio using HERMflasher.
Click to expand...
Click to collapse
Aha this should work because the device was already in bootloader when we ran the RUU for a second time, how we got past CID check in the early days?
Makes sence to try this.
I try it...
Must I start it in bootloader-mode ?
and have I to activate active-sync or disable it ?
Bundy said:
Must I start it in bootloader-mode ?
Click to expand...
Click to collapse
yes
Bundy said:
and have I to activate active-sync or disable it ?
Click to expand...
Click to collapse
disable
So, I've done it serveral times...
After the first time - Error222 : Device not responding
After the 2nd time - Error 250 - Update Error
and I have done it a 3rd time - Update Error again.
why can't i flash the hermes with my micro-sd ?
Bundy said:
secondyl... my phone doesn't start - first it looks like a tv with no antenna and with some numbers at the botton - also no gsm
and then i see the blue "windows-mobile" screen.
thirdly - i have flashe my device and since the flashing the hermes doesnt start
I think I've tries everything - but nothing helped
Click to expand...
Click to collapse
i have the same, except that the reason is that i touched the usb cable and it disconnected and when i try to put the firmware, i have error 260
yes, I have also ERROR260 and not 250. Sorry...
And what have you done with your device ?
I have the same problem! It seem that there in no connection between the pc and pda... Other methods to update? I tried with the micro-sd too... It starts, but when it checks, so it freeze... Maybe the CID of the pda and the ROM's one is different?
Bundy said:
So, I've done it serveral times...
After the first time - Error222 : Device not responding
After the 2nd time - Error 250 - Update Error
and I have done it a 3rd time - Update Error again.
Click to expand...
Click to collapse
I have the same problems. Put WM6 on my device. Now I have the Error 222. Also when I put HERMIMG on a SD card he do nothing. The difference between your device and mine is, that i boot the device but can't change any data. Don´t know what to do....
I am just trying the hermflasher.
Does anyone know how long the flash will last ?
There is no progress shown - only FLASH NBH on the device.
You should not flash a NBH, you should flash a radio: extract GSM.nb from the NBH file and flash it using the command 'hermflasher -F radio GSM.nb'.
@pof :
I've done what you said - and it works.
At start i have the strange screen (like a tv without antenna) but then it works.
Now I have : ROM-Version 1.25.207.2
Funkempf. 1.03.03.10
Prot. 32.34.7010.01H
Thanks a lot for your help.
And now, I consider to put another ROM on it (WM6 ?). to get at least a normal screen at startup.
First consider puting HardSPL to avoid bricking it again
Then flash any NBH containing the splash screens and you'll get the boot screen back
anyone know what rom is compatible with athe100 SPL 1.10 ?
i know theirs lots of 1.2 and 3.5 spl roms, i tryed to flash a 3.5spl on my phone and now only way i can turn on the phone is in bootloader, i try to flash the phone but it always gets stuck at 1%, can anyone assist me?
cowballz69 said:
anyone know what rom is compatible with athe100 SPL 1.10 ?
i know theirs lots of 1.2 and 3.5 spl roms, i tryed to flash a 3.5spl on my phone and now only way i can turn on the phone is in bootloader, i try to flash the phone but it always gets stuck at 1%, can anyone assist me?
Click to expand...
Click to collapse
Have you took the sim card and memory card out?????
Jay
yes they are both out when tryign to flash, been over a week with out a working athena
cowballz69 said:
yes they are both out when tryign to flash, been over a week with out a working athena
Click to expand...
Click to collapse
try flashing your original ROM which should be found in the wiki section.
ignore what I said below and report back if you were able to load your original ROM
***Ignore this read above**Once your phone is working , do the athena wrapper which should load SPL 1.2
Also read this
http://forum.xda-developers.com/showthread.php?t=429013
yes I tryed to flash the original rom (its a wm5 i beleive to), still gets error after 1%,, downloaded both on the wiki and the ftp site, =\ been over a week so far no clues on why i cant flash, i even tryed to change the mac address using mtty, but instead of going into level = 0 , i get level = FF witch means the phone is locked out from flashing anything threw mtty,
thank u guys so much for responding on my issue
I also tryed doing the unlocker and its a no go
If the error when it stops at 1% is "invalid model id" the solution is here http://forum.xda-developers.com/showpost.php?p=2154726&postcount=33
cowballz69 said:
yes I tryed to flash the original rom (its a wm5 i beleive to), still gets error after 1%,, downloaded both on the wiki and the ftp site, =\ been over a week so far no clues on why i cant flash, i even tryed to change the mac address using mtty, but instead of going into level = 0 , i get level = FF witch means the phone is locked out from flashing anything threw mtty,
thank u guys so much for responding on my issue
I also tryed doing the unlocker and its a no go
Click to expand...
Click to collapse
I think this means your phone is not unlocked
with respect to sergiopi , you cant do the mtty script.
I would suggest you msg cmonex or try to talk to her on IRC on the
dxa-devs channel
addendum
seeing that you have nothing to lose, why dont you try flashing the original rom from the sd card using the method in the wiki
cowballz69 said:
anyone know what rom is compatible with athe100 SPL 1.10 ?
i know theirs lots of 1.2 and 3.5 spl roms, i tryed to flash a 3.5spl on my phone and now only way i can turn on the phone is in bootloader, i try to flash the phone but it always gets stuck at 1%, can anyone assist me?
Click to expand...
Click to collapse
I have the same problem.
what I do...
I have ameo t-mobile...windows mobile 5.0
run AthenaUnlocker
Step 1 make all finish noc problem
Step 2 hung up on 60 %
bootloader no problem....but can´t flash original flash always stuck at 1% and reboot...
flashing the original rom from the sd card using the method in the wiki ...
make it, but no do...on screen see
cheking...
loading....
than come on screen
0002802
ching...
loading...
not allowed
sergiopi said:
If the error when it stops at 1% is "invalid model id" the solution is here http://forum.xda-developers.com/showpost.php?p=2154726&postcount=33
Click to expand...
Click to collapse
My error when it stops at 1% is "invalid vender id"
my image version is demaged
Re: Ameo from t-Mobile german - repair
________________________________________
hi
what is your CID? use mtty command "info 2" to find out.
for example, if it is TMOB_007, you have to find a shipped athena rom with that CID.
if you cannot find a matching rom, let me know, i can still help,
cmonex
HTCS Þ?ÒtHTCE
please need halp
thx
felix999
read this post http://forum.xda-developers.com/showpost.php?p=2154726&postcount=33
read this post which tells you how to run mtty
follow the instructions to start mtty then press enter to get the cmd prompt
then type info 2 to get your CID
depending on this you will be able to flash the apprpriate ROM
lakeman said:
read this post which tells you how to run mtty
follow the instructions to start mtty then press enter to get the cmd prompt
then type info 2 to get your CID
depending on this you will be able to flash the apprpriate ROM
Click to expand...
Click to collapse
in mtty this can read:
when type task 32
become LEVEL: FF
when type info 2:
HTCS Þ?ÒtHTCE
my CID is 1.1
on bootscreen can see this:
ATHE100
IPL-v1.00
ATHE100
SPL-v1.10.RP00
what I do before...
Ameo WM 5.0 >>>>my mistake not update to WM6.0
run AthenaUnlocker
STEP1>>>OK
STEP2>>>by 60 % hang and stopped....
and now have the big problems.....Image ROM of t-Mobile 5.0 german demaged
can´t flash any rom´s
thx for hel or I want to pay bucks for service, when ma ameo live again...
felix999
lakeman said:
read this post which tells you how to run mtty
follow the instructions to start mtty then press enter to get the cmd prompt
then type info 2 to get your CID
depending on this you will be able to flash the apprpriate ROM
Click to expand...
Click to collapse
this is my CID
Cmd>info 2
info 2
Wait interpreter timeout
HTCS Þ?ÒtHTCE
????????
don´t know
felix999
Athena mobile 6 > SPL 1.10
become today a answer from crazy cat, that olipro say must take an rom in athena forum....
I flaswh with so many roms...anytime same error: error 294 - invalid vendor ID.....
My SPL 1.10 >>> can´t find a rom with SPL 1.10
what rom can repair my demaged ameo?????
thx for help
felix999
problem solved with ONLINEHELP from>>>>>cmonex>>>><<:::::>><<:::E:::>><<:::R:::>><<:::F:::>><<:::E:::>><<:::C:::>><<:::T:::>>
thx
felix999
lakeman said:
try flashing your original ROM which should be found in the wiki section.
Click to expand...
Click to collapse
Is this how you solved your problem?