anyone know what rom is compatible with athe100 SPL 1.10 ?
i know theirs lots of 1.2 and 3.5 spl roms, i tryed to flash a 3.5spl on my phone and now only way i can turn on the phone is in bootloader, i try to flash the phone but it always gets stuck at 1%, can anyone assist me?
cowballz69 said:
anyone know what rom is compatible with athe100 SPL 1.10 ?
i know theirs lots of 1.2 and 3.5 spl roms, i tryed to flash a 3.5spl on my phone and now only way i can turn on the phone is in bootloader, i try to flash the phone but it always gets stuck at 1%, can anyone assist me?
Click to expand...
Click to collapse
Have you took the sim card and memory card out?????
Jay
yes they are both out when tryign to flash, been over a week with out a working athena
cowballz69 said:
yes they are both out when tryign to flash, been over a week with out a working athena
Click to expand...
Click to collapse
try flashing your original ROM which should be found in the wiki section.
ignore what I said below and report back if you were able to load your original ROM
***Ignore this read above**Once your phone is working , do the athena wrapper which should load SPL 1.2
Also read this
http://forum.xda-developers.com/showthread.php?t=429013
yes I tryed to flash the original rom (its a wm5 i beleive to), still gets error after 1%,, downloaded both on the wiki and the ftp site, =\ been over a week so far no clues on why i cant flash, i even tryed to change the mac address using mtty, but instead of going into level = 0 , i get level = FF witch means the phone is locked out from flashing anything threw mtty,
thank u guys so much for responding on my issue
I also tryed doing the unlocker and its a no go
If the error when it stops at 1% is "invalid model id" the solution is here http://forum.xda-developers.com/showpost.php?p=2154726&postcount=33
cowballz69 said:
yes I tryed to flash the original rom (its a wm5 i beleive to), still gets error after 1%,, downloaded both on the wiki and the ftp site, =\ been over a week so far no clues on why i cant flash, i even tryed to change the mac address using mtty, but instead of going into level = 0 , i get level = FF witch means the phone is locked out from flashing anything threw mtty,
thank u guys so much for responding on my issue
I also tryed doing the unlocker and its a no go
Click to expand...
Click to collapse
I think this means your phone is not unlocked
with respect to sergiopi , you cant do the mtty script.
I would suggest you msg cmonex or try to talk to her on IRC on the
dxa-devs channel
addendum
seeing that you have nothing to lose, why dont you try flashing the original rom from the sd card using the method in the wiki
cowballz69 said:
anyone know what rom is compatible with athe100 SPL 1.10 ?
i know theirs lots of 1.2 and 3.5 spl roms, i tryed to flash a 3.5spl on my phone and now only way i can turn on the phone is in bootloader, i try to flash the phone but it always gets stuck at 1%, can anyone assist me?
Click to expand...
Click to collapse
I have the same problem.
what I do...
I have ameo t-mobile...windows mobile 5.0
run AthenaUnlocker
Step 1 make all finish noc problem
Step 2 hung up on 60 %
bootloader no problem....but can´t flash original flash always stuck at 1% and reboot...
flashing the original rom from the sd card using the method in the wiki ...
make it, but no do...on screen see
cheking...
loading....
than come on screen
0002802
ching...
loading...
not allowed
sergiopi said:
If the error when it stops at 1% is "invalid model id" the solution is here http://forum.xda-developers.com/showpost.php?p=2154726&postcount=33
Click to expand...
Click to collapse
My error when it stops at 1% is "invalid vender id"
my image version is demaged
Re: Ameo from t-Mobile german - repair
________________________________________
hi
what is your CID? use mtty command "info 2" to find out.
for example, if it is TMOB_007, you have to find a shipped athena rom with that CID.
if you cannot find a matching rom, let me know, i can still help,
cmonex
HTCS Þ?ÒtHTCE
please need halp
thx
felix999
read this post http://forum.xda-developers.com/showpost.php?p=2154726&postcount=33
read this post which tells you how to run mtty
follow the instructions to start mtty then press enter to get the cmd prompt
then type info 2 to get your CID
depending on this you will be able to flash the apprpriate ROM
lakeman said:
read this post which tells you how to run mtty
follow the instructions to start mtty then press enter to get the cmd prompt
then type info 2 to get your CID
depending on this you will be able to flash the apprpriate ROM
Click to expand...
Click to collapse
in mtty this can read:
when type task 32
become LEVEL: FF
when type info 2:
HTCS Þ?ÒtHTCE
my CID is 1.1
on bootscreen can see this:
ATHE100
IPL-v1.00
ATHE100
SPL-v1.10.RP00
what I do before...
Ameo WM 5.0 >>>>my mistake not update to WM6.0
run AthenaUnlocker
STEP1>>>OK
STEP2>>>by 60 % hang and stopped....
and now have the big problems.....Image ROM of t-Mobile 5.0 german demaged
can´t flash any rom´s
thx for hel or I want to pay bucks for service, when ma ameo live again...
felix999
lakeman said:
read this post which tells you how to run mtty
follow the instructions to start mtty then press enter to get the cmd prompt
then type info 2 to get your CID
depending on this you will be able to flash the apprpriate ROM
Click to expand...
Click to collapse
this is my CID
Cmd>info 2
info 2
Wait interpreter timeout
HTCS Þ?ÒtHTCE
????????
don´t know
felix999
Athena mobile 6 > SPL 1.10
become today a answer from crazy cat, that olipro say must take an rom in athena forum....
I flaswh with so many roms...anytime same error: error 294 - invalid vendor ID.....
My SPL 1.10 >>> can´t find a rom with SPL 1.10
what rom can repair my demaged ameo?????
thx for help
felix999
problem solved with ONLINEHELP from>>>>>cmonex>>>><<:::::>><<:::E:::>><<:::R:::>><<:::F:::>><<:::E:::>><<:::C:::>><<:::T:::>>
thx
felix999
lakeman said:
try flashing your original ROM which should be found in the wiki section.
Click to expand...
Click to collapse
Is this how you solved your problem?
Related
here is what I've done and what happened:
my ROM was HTC 1.18.255.3 07/22/06 with bootloader 1.04 then I ran "HERM_Unlock_v2a.exe" on the device but I didn't use "HTC_Hermes_Radio_for_SIMunlock_v1.16.00.69" to save time and i wanted a CID unlock only.
after "SUCCESS!" message from "HERM_Unlock_v2a.exe", I connected my device via USB to PC and started to upgrade to Cingular 1.31.502.1 08/30/06 with aku 2.6 and bootloader 1.06 but when I get the "ID ERROR",without disconnecting the USB, I switched back to ugrading to previous ROM HTC 1.18.255.3 and the Processe started with no problem untill 98%, then suddenly upgading interrupted a message came saying connection error or somting like that!
since then my device is stuck on windows mobile screen and I've tested solutions in the "Hermes_Upgrade Problems" page and tried using the "Hermes SD Card flashing" method, But It seems impossible to flash my phone agian.
Help me PLEASE,HELP
someone help me please!
POF can't you help me please
I think Pof is away until 3rd december, I have the similiar problems with my second hermes, if you have then use mtty to see if you have an corrupted cid using info 2.
Do you have the original rom to go back on if so that will fix your problem.
I've used mtty to send some commands to my device and it answers to some of them but It just stop responding when I type "info 2" or "info 3".
and i tried this in mtty:
"
USB>checkimage
IPL CRC checksum = 0x9FCC6BEB
SPL CRC checksum = 0x3BF03635
CE CRC checksum = 0xC0E1751A
ExtROM CRC checksum = Total Block= 1024
dwBlockIndex= 1024
Address Error1!!!
Get checksum ERROR!!!
0x0
Radio Image CRC checksum =
"
again It stop responding
also tried upgrading, no matter which ROM I try, it just can't connect to device.
and thanx for your relpy.
hi, since there is NO htc service center available around me I have to do something about it myself but my phone is still dead and I'm using a nokia 1101. PLEASE someone help me, pof are you back? can you help me?
I've tried all in this page:
"http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems"
and this one too:
"http://forum.xda-developers.com/showthread.php?t=280733"
and tested qtek 2020 rom but no use.
from what I've found out my device hang up and stop responding when it gets the "INFO 2" or "INFO 3" or "TASK 32" or perhaps any thing involving CID so no upgrading utility is able to connect to it, the only thing is to connect to it using "mtty.exe" which I've tried any command found here, but no use again.
and my SPL is 1.04
can anyone help me?
mht220 said:
I ran "HERM_Unlock_v2a.exe" on the device but I didn't use "HTC_Hermes_Radio_for_SIMunlock_v1.16.00.69" to save time and i wanted a CID unlock only.
Click to expand...
Click to collapse
Wrong, you also need a patched radio to CID unlock. Running only the exe file without the patched radio has no effect on the unit.
mht220 said:
from what I've found out my device hang up and stop responding when it gets the "INFO 2" or "INFO 3" or "TASK 32" or perhaps any thing involving CID so no upgrading utility is able to connect to it, the only thing is to connect to it using "mtty.exe" which I've tried any command found here, but no use again.
and my SPL is 1.04
Click to expand...
Click to collapse
Please attach usb monitor capture when trying to flash a ROM and a radio ROM. Otherwise can't help you.
here is exported files from usb-monitor:
and tanx for your reply
uuh... there must be something really wrong with it, no response to bootloader commands. If no sd card flashing is possible, I would suggest you to send it to service centre too.
pof said:
...I would suggest you to send it to service centre too.
Click to expand...
Click to collapse
It's a difficult option for me, as I should send it to a foreign country to service center,so are you sure there is no way like erasing somewhere using mtty?
pof said:
... no response to bootloader commands...
Click to expand...
Click to collapse
but it respond to some of them in mtty.exe e.g. "erase", "set" and some other.
pof said:
...If no sd card flashing is possible...
Click to expand...
Click to collapse
no it would stuck in "checking..." forever
tanx
HI,
I have same exactly problem on my spv m3100: since sept06 I've tried every kind of Unlock software,upgrade ROM and method found in xda..In mtty bootloader (spl 1.04) respond at every command but not "info 2","info 3" and "task 32".Sd card method works but if you try to upgrade other ROM,in your screen "loading..." and then "checking..." hangs on because the ROM upgrade must to match CID (I suppose..).I'll wait the next ROM Upgrade and ORANGE won't release it until gen07..
warrio said:
I'll wait the next ROM Upgrade and ORANGE won't release it until gen07.
Click to expand...
Click to collapse
it seems your problem is like mine if so, I don't think ANY normal upgrade can solve your prolem 'cause it can't connect to it.
so don't wait and send your device to service center, if you can.
I'm in your same conditions:there's no repair center here so I have to wait Orange who release a upgrade Rom (I hope asap..).
He Guys,
Just my luck I have bought an HTC Tytn with the original Dutch rom and sim unlocked second hand.
I wanted to put a new Dutch rom from HTC on it but I keep on getting the ERROR [244] : INVALID MODEL ID but what I don`t understand is I have used the original Dutch rom from HTC. So I checked the device information and under the tab identity it says;
Model No.: H
Platform: PocketPC
IMEI: xxxxxxxxxxxxxxxxxxx
Shouldn’t the Model No. be HERM200?
Has anyone any suggestions in how I can solve this problem so I can flash any rom I wish.
I have tried al the cid unlock programs I could find and in bootloader it says;
H
IPL-1.01
H
SPL-1.40.Olipro
Thanks in advanced.
Use RAR to unpack the Original Dutch ROM.
Take the NBH file that you get when you unpack the ROM.
Put it in a folder with CUSTOM_RUU from Olipro.
Run CUSTOM_RUU and it will load up the ROM from the NBH file, bypassing the CID check. Should work
Thanks for the reply,
I have tried what you suggested but I still get ERROR [244] : INVALID MODEL ID I have also read these posts http://forum.xda-developers.com/showthread.php?t=322231&highlight=CUSTOM_RUU+from+Olipro and http://forum.xda-developers.com/showthread.php?t=322119&highlight=CUSTOM_RUU+from+Olipro and http://forum.xda-developers.com/showthread.php?t=309707&highlight=CUSTOM_RUU+from+Olipro and tried these suggestions but every time I get the error message. The radio update process was the same for me it will go to 7% and then give the message ERROR [244] : INVALID MODEL ID.
I have also tried the HTC_Hermes_SIM_CID_Unlock_v3a and Hard-SPL-V7 but still get the error message.
I hope I’m doing something wrong if not then I hope you have a new suggestion.
Thanks in advance.
Please set your device in BOOTLOADER MODE and post here your IPL / SPL versions.
Junner2003 said:
Please set your device in BOOTLOADER MODE and post here your IPL / SPL versions.
Click to expand...
Click to collapse
Did you read first post?
VivaErBetis said:
Did you read first post?
Click to expand...
Click to collapse
Ups, missed the bottom - thought it is the signature already! Sorry, haven't had my coffee yet!
Well, looks like the device is CID unlocked!
How about trying to flash an entire cooked ROM?
i would suggest the following:
flash a cooked rom (any)
see if that makes any difference to your model id
then try and flash the native dutch rom
good luck
Hi Guys,
As you suggested I tried a cooked rom the Hermes_WM6_vanilla still get the same error message when I put my device manually in boot loader it shows;
H
IPL-1.01
H
SPL-1.40.Olipro
But as soon as I try an official or cooked rom it shows;
H
IPL-SSPL by des
H
SPL-1.09.ds
I’m now trying Schaps_WM6Pro_WWE_4.00_Full_Beta3.exe and choose for auto detect and it said 1.40 Olipro and in boot loader it shows;
H
IPL-1.01
H
SPL-1.40.Olipro
And after 1% I got the ERROR [244] : INVALID MODEL ID message again.
I think my options are getting slim.
Your ModelID is stored on NAND and can be edited quite trivially (mostly).
how it got corrupted I don't know, however, the important question is; can you get into the OS?
He Olipro,
The device it zelf works perfect I can go anywhere I want even in the OS.
Just lead the way.
Changing Model ID
I have a similar problem in that my Model ID got corrupted during a radio upgrade. I now get the same error (244) and am stuck on SPL2.10 and can't downgrade to fix it. Can anyone tell us how to manually change the model ID in the NAND?
Much appreciated.
Dumping NAND
Ok, I'm a relative newbie so appologies before I get flamed. Thanks Olipro for giving me a clue.
I have now got spl 2.60 on my device but am unsure how to dump the NAND. I've worked out how to dump the 3 partitions from the device to dump the OS but am still unclear which part of the device is the NAND. I've read the Wiki on the memory map but am still not too sure.
Anyone able to give me simple instructions to dump the NAND and once I've done that where abouts is the ModelID stored? Do I do this using mtty?
Thanks in advance.
http://forum.xda-developers.com/showthread.php?t=322225
NAND Dump
Thanks Drummer for pointing me in the right direction.
Ive done this bit:
BTW, if you want to do a full backup of you FULL eeprom nand at any time, connect as before and type these commands:
plink HERMES > full.nb (hit ENTER twice)
task 32 (hit ENTER once and only once from now on after every command)
password 0000000000000000 - My device password is BsaD5SeoA which I used instead.
set 1e 1
rbmc me.txt 50000000 7fff800
watch your file grow to 128 MB.
It creates a full.nb file but it stays at 1k!!
** Note I have copied the bootloader file for spl 2.60 on my Hermes and ran that so I can now use that versino instead of the 2.10 thats on my device if that makes a difference and have tried with no joy with either version. Yes I know it says to use 2.30 but I can't work out how to get that on my device due to the ModelID error.
The Model number is contained within the herm1.nb file that was posted by BusStop in that thread. No need for complete NAND reflashing, only that section. You'll see it using a Hex Editor. You should write down your WiFi MAC addess, so you can edit it before flashing the file with the corrected Model number. Now you just have to figure out how to get SPL 1.01 MFG on your device...
Thanks Drummer. I did try flashing the herm1.nb file but of course as I do not have SPL 1.01 MFG it gievs an error. I'll keep trawling through the site and see if I can work out how to get SPL 1.01 onto my device. I'm not going to let this damn device beat me.
Ok so I worked out how to get the ModelID using getdevicedata. Used nbhtool to create a vaild nbh using the ModelID I'd just got and used the spl from 2.30 and it updated that fine.
Excellent.
However did the same with the MFG1.01 and flashed it and......
I now have a dead brick, no power and no response form usb. Time to get a replacement device.
Thanks for all the help I've had. I'm sure it should have worked.
1.) Remove battery
2.) Connect Hermes to charger or USB
3.) Insert the battery while Hermes is connected to charger
4.) Red light should turn Amber
5.) Soft Reset
Thanks for the advice Drummer however:
1.) Remove battery
2.) Connect Hermes to charger or USB
3.) Insert the battery while Hermes is connected to charger
4.) Red light should turn Amber - Nope red light goes out!
Mne shows HHHHHHH
Hi all, i've upgraded my radio and after my model id changed to H.
So, reading some posts i've used NBHTOOL.
1.I've decompiled an original Italian ROM
2.i've obtained a custom nbh selecting only OS and EXTROM and changing my Model number.
3. after that i've flashed the nbh resulting into a write error at 84% and a bricked htc.
Luckily i was able to reflash roms and i processed to second experiment.
I've made a custom rom with only the os, and it WORKED!
so my questions are:
1. can i use my htc even if my external rom isn't flashed (it cames from an old Schaps 4.0 succesful flash)
2. It is safe to proceed installing bootloader SPL using the nbhtool like i did with the os?
In that case i will be able to fix the model id problem by flashinh spl 1.01 and using the wireless fixing method you posted..
Thanks in advance for your reply!
Hi
From my understanding the Ext rom is mainly used for carriers to install there specific addons and customizations so it shouldn't be a problem.
As you can see I did flash spl 2.30 using this method and it worked fine ti was only when something whent wrong flashing 1.01 that my problem happened but I think that may be that I used an nbs file instead of an nb file from what I've read since.
Good luck.
Edit: Just noticed someone on this thread has managed it by going straight ot 2.60 http://forum.xda-developers.com/showthread.php?t=322225
I have a jasjam
i was upgrading it using the telstra WM6 rom.
during the upgrade it was around 15% that the upgrade utility show the error that device cannot connect.
my device is bricked now
IT is not KITL enabled
it the first splash screen it shows no gsm
it only shows the bootloader menu
IPL 1.04
SPL 2.03
i read the wiki on how to unbrick a bricked hermes but there is no sulotion
plzzzzzzzz
anyone can help me??????
koorosh_bsboys said:
I have a jasjam
i was upgrading it using the telstra WM6 rom.
during the upgrade it was around 15% that the upgrade utility show the error that device cannot connect.
my device is bricked now
IT is not KITL enabled
it the first splash screen it shows no gsm
it only shows the bootloader menu
IPL 1.04
SPL 2.03
i read the wiki on how to unbrick a bricked hermes but there is no sulotion
plzzzzzzzz
anyone can help me??????
Click to expand...
Click to collapse
Did you also read the wiki to see how to install hardspl to protect your device BEFORE flashing ?(here: http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=30&Itemid=27 )? Are you using Olipro hardspl?
Try to use the SDCARD method (Format a sdcard in FAT32. Copy the nbh file on it and rename it HERMIMG.NBH. Insert the card and HR : OK/POWER/Soft reset. Follow the instructions)
i tested that but didn't help
does anybody have any suggestion??
Try solution to reeboot ( sometimes helps)
1. get out SIM and SD card
get mtty http://forum.xda-developers.com/download.php?id=9864
2. Make BL mode on Hermes
2a on PC ActiveSync - coonection properties untick allow to connect by USB
3. start mtty on PC , choose USB and enter.
4. next enter.
5. type set 14 and enter
6. type task 8 and enter
OS have to boot if no go to 7
7. enter
8 type set 16 and enter
9. type task 8 and enter
Hope that will boot
http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
Pretty much all the info on unbricking is in this table by Pof. If this doesn't sort you out then you're have to send it off to imeicheck etc for repair.
The history so far
I have bricked my jasjam while updating to telstra wm6
I have not super CID my device before upgrading to telstra wm6
Now my device freezed at second splash screen
IPL 1.04
SPL 2.03
NO GSM
when i used the info 6 command on mtty it says NO CID
i can not upgrade my device from SD CARD (memory stick)
i used these command on MTTY.exe but no improvement
set 14
task 8
set 16
task 8
when i tried to rom upgrade using any ruu (ruuwraper,.....) it only shows 1% and my device reboots and ....
any suggestions????
I hope you understand this, Basically if
1. You have a "No GSM"
2. Your CID is corrupted
3. Your OS has no KITL mode
4. You didn't use HARDSPL...
Then your phone is screwed, and you need to buy a new one or send it to repair.
Hope you have better luck with your next phone. (you seem to be collecting bricked phones!)
Wam7 said:
4. You didn't use HARDSPL...
Click to expand...
Click to collapse
That's the BIGGEST mistake u ever made with ur Jasjam, bro
try to send to repair centre, if repair cost is too much. Than u have to decide try but new gadget. Kaiser looks flirt to me
yep im glad i waited to upgrade from the proper wm5 to the proper wm6
st3v3 said:
yep im glad i waited to upgrade from the proper wm5 to the proper wm6
Click to expand...
Click to collapse
Did u mean, u stay at proper WM5 or already Flash to WM6 ?
I think everything is save IF we read carefully the disclaimer from the author
ermenzegna said:
Did u mean, u stay at proper WM5 or already Flash to WM6 ?
I think everything is save IF we read carefully the disclaimer from the author
Click to expand...
Click to collapse
The offical I-mate telstra Jasjam rom for WM6 came out recently previous to that i just kept the original WM5 rom that it came with much to the dismay of my peers, actually considered it a few times but decided against it till the official rom came out.
yeah if you follow the instructions for the WM6 rom you use it should be ok however the "Murphys law" of programming tends to suggest there will always be an error that they dont allow for.
st3v3 said:
The offical I-mate telstra Jasjam rom for WM6 came out recently previous to that i just kept the original WM5 rom that it came with much to the dismay of my peers, actually considered it a few times but decided against it till the official rom came out.
yeah if you follow the instructions for the WM6 rom you use it should be ok however the "Murphys law" of programming tends to suggest there will always be an error that they dont allow for.
Click to expand...
Click to collapse
This has NOTHING to do with only using official Roms! One has pretty much the same chance of bricking their phone evening using an official WM6 as a cooked variant from Schaps et al..
Simply put if you don't use HardSPL then you're asking for trouble no matter what the ROM. You should also use the MicroSD wherever possible as it is much more reliable.
imei check use jtag to fix this
imei check use jtag to fix this ,CAn we use jtag to fix this in hermes. need help to resovle spl 2.03 cid locked no gsm.
I tried to run unlocker, step 1 was successful but during step 2 there was an error and the program crashed.
Now the phone can enter bootloader when I switch on, when I try to flash a ROM I stays on %
Please help
sorry to hear that happend to you as you were trying to unlock your phone....
but when you enter boot loader what does it say at the top?
My athena also failed at upgrade... now, it only stops at opening logo..
I already have Hard-SPL installed but I don't find any program like HTC trinity Stack Overflow Exploit to unbrick it..
bootloader is still possible.. then what should I do?
and how do you use mtty?
Think before you jump to conclusions.
raf1987 said:
My athena also failed at upgrade... now, it only stops at opening logo..
I already have Hard-SPL installed but I don't find any program like HTC trinity Stack Overflow Exploit to unbrick it..
bootloader is still possible.. then what should I do?
and how do you use mtty?
Click to expand...
Click to collapse
Think before you jump to conclusions.
If it tries to boot and stops at the opening logo , the rom is corrupted but not bricked.
If you can get into bootloader you can usually resurrect without resorting to mtty ,which only really cmonex here knows how to use properly.
Check which SPL is visible in the bootloader screen and then flash an appropriate ROM.
ie SPL 1.1 > original ROM
SPL 1.2 > any spl 1.2 ROM.
lakeman said:
Think before you jump to conclusions.
If it tries to boot and stops at the opening logo , the rom is corrupted but not bricked.
If you can get into bootloader you can usually resurrect without resorting to mtty ,which only really cmonex here knows how to use properly.
Check which SPL is visible in the bootloader screen and then flash an appropriate ROM.
ie SPL 1.1 > original ROM
SPL 1.2 > any spl 1.2 ROM.
Click to expand...
Click to collapse
If you put it in bootloader screen (FULL PRESS camera button, while poking reset hole) What does it say on the "SPL" line eg; 1.1, 1.2, or 3.5? and what ROM are you trying to use?.................Hi Lakeman
Jay
athena x7500
please help. i have the same problem.
after flash with athenaunlocker after step 1 ,in step 2 my athena make error and my x7500 cannot power on but i can put it in bootloder made.
when i want to flash it with other rom it take 12% and show error.
who can help me please.
ATHE100
IPL-v2.02
ATHE100
SPL-v1.20.Olipro
help please
likebie said:
who can help me please.
ATHE100
IPL-v2.02
ATHE100
SPL-v1.20.Olipro
help please
Click to expand...
Click to collapse
you have to load an spl 1.2 rom while in bootloader
make sure you remove your sim and sd card first
My Raphael is dead...
1. I flash Hard SPL 1.90.OliNex
2. I flash original Russian ROM and have this message on screen "Your OS ROM isn't customized for your hardware. Please reflash the proper ROM code or contact the service center"
3. I flash stock SPL
and now when I'm trying to flash any ROM or Hard SPL I have on the screen of PC "0% image upgrade in progress" and "0%" on the screen of Raphael
after some time on the screen of PC I see ERROR [262]: UPDATE ERROR
What I must to do?
Help me, please
P.S.
Now when I'm trying to flash HTC_Raphael_hTC_Asia_WWE_1.90.707.1_Radio_Signed_R aphael_52.33.25.17_1.02.25.19 I have "Invalid Vendor ID" Message
dishef said:
P.S.
Now when I'm trying to flash HTC_Raphael_hTC_Asia_WWE_1.90.707.1_Radio_Signed_R aphael_52.33.25.17_1.02.25.19 I have "Invalid Vendor ID" Message
Click to expand...
Click to collapse
When you receive "Invalid Vendor ID", than your device is not Hard SPL! Please follow the update procedure again. There must have been something wrong.
DeepThought said:
When you receive "Invalid Vendor ID", than your device is not Hard SPL! Please follow the update procedure again. There must have been something wrong.
Click to expand...
Click to collapse
But when I'm trying to flash Hard SPL I have ERROR[262]
Does any method to flash Hard SPL from SD card exist?
dishef said:
But when I'm trying to flash Hard SPL I have ERROR[262]
Click to expand...
Click to collapse
Read here please http://forum.xda-developers.com/showthread.php?t=425922
taiseer999 said:
Read here please http://forum.xda-developers.com/showthread.php?t=425922
Click to expand...
Click to collapse
sorry for the offtopic (or not...)
i have tryied many times to connect to my TP using mtty, but no luck. i'm using Vista Ultimate, and can connect and use mtty with my Kaiser, but can't with Raphael.
Is there any special thing i need to do to get mtty working with raphael?
Thanks in advance
Cheers
jcespi2005 said:
sorry for the offtopic (or not...)
i have tryied many times to connect to my TP using mtty, but no luck. i'm using Vista Ultimate, and can connect and use mtty with my Kaiser, but can't with Raphael.
Is there any special thing i need to do to get mtty working with raphael?
Thanks in advance
Cheers
Click to expand...
Click to collapse
Have you remembered to disable USB connections from activesync connection settings?
taiseer999 said:
Read here please http://forum.xda-developers.com/showthread.php?t=425922
Click to expand...
Click to collapse
i used the MTTY to format the device
but still have ERROR[262] when trying to flash Hard SPL
using info 2 on MTTY i got "HTCSHTC__J15Wаа`HTCE"
but I have HTC Raphael (Touch Pro)
does any way to flash hard spl with MTTY exist?
or may be I can flash ROM with MTTY?
i have this problem whit hard spl
i test it whitout sim-micro sd-win xp-win vista-i dont use usb hub
i use ssple but i had 262 error again and pc was hang on 0%
i have touch pro
i dont want MTTY
it's risk
maby my phon is going to be off for ever
This procedure can damage your phone