I tried to run unlocker, step 1 was successful but during step 2 there was an error and the program crashed.
Now the phone can enter bootloader when I switch on, when I try to flash a ROM I stays on %
Please help
sorry to hear that happend to you as you were trying to unlock your phone....
but when you enter boot loader what does it say at the top?
My athena also failed at upgrade... now, it only stops at opening logo..
I already have Hard-SPL installed but I don't find any program like HTC trinity Stack Overflow Exploit to unbrick it..
bootloader is still possible.. then what should I do?
and how do you use mtty?
Think before you jump to conclusions.
raf1987 said:
My athena also failed at upgrade... now, it only stops at opening logo..
I already have Hard-SPL installed but I don't find any program like HTC trinity Stack Overflow Exploit to unbrick it..
bootloader is still possible.. then what should I do?
and how do you use mtty?
Click to expand...
Click to collapse
Think before you jump to conclusions.
If it tries to boot and stops at the opening logo , the rom is corrupted but not bricked.
If you can get into bootloader you can usually resurrect without resorting to mtty ,which only really cmonex here knows how to use properly.
Check which SPL is visible in the bootloader screen and then flash an appropriate ROM.
ie SPL 1.1 > original ROM
SPL 1.2 > any spl 1.2 ROM.
lakeman said:
Think before you jump to conclusions.
If it tries to boot and stops at the opening logo , the rom is corrupted but not bricked.
If you can get into bootloader you can usually resurrect without resorting to mtty ,which only really cmonex here knows how to use properly.
Check which SPL is visible in the bootloader screen and then flash an appropriate ROM.
ie SPL 1.1 > original ROM
SPL 1.2 > any spl 1.2 ROM.
Click to expand...
Click to collapse
If you put it in bootloader screen (FULL PRESS camera button, while poking reset hole) What does it say on the "SPL" line eg; 1.1, 1.2, or 3.5? and what ROM are you trying to use?.................Hi Lakeman
Jay
athena x7500
please help. i have the same problem.
after flash with athenaunlocker after step 1 ,in step 2 my athena make error and my x7500 cannot power on but i can put it in bootloder made.
when i want to flash it with other rom it take 12% and show error.
who can help me please.
ATHE100
IPL-v2.02
ATHE100
SPL-v1.20.Olipro
help please
likebie said:
who can help me please.
ATHE100
IPL-v2.02
ATHE100
SPL-v1.20.Olipro
help please
Click to expand...
Click to collapse
you have to load an spl 1.2 rom while in bootloader
make sure you remove your sim and sd card first
Related
ok. it says this in the tri-color screen:
HERM100
IPL-1.04
HERM100
SPL-1.40.Olipro
ok. so i download the Hard-SPL-V7 and it works. and it says that up there on my boot loader. but what is my bootloader version? 1.40? or 1.04? and what is this talk of the SPL-2.10.Olipro. how do i get that? im confused
oh another thing. why does it freeze on the GSM- part when i use the SDcard method? anyone? help thank you
the latest bootloader is 2.10.Olipro (the latest official one I've released for general consumption)
to flash it, please do remember NOT to put your phone in bootloader and to have activesync synced.
IPL is Initial Program Loader, and is generally not too exciting.
SPL is Secondary Program Loader and this one handles flashing etc and is the one with the exciting crap you need to patch.
have you been able to flash GSM with SD or somehow else ?
I ve asked how to fix it about 100 times on this forum and my device is still bricked
after update my hermes my phone dosent start windows after another upfate with a shipped rom the phone finish the update but stil dident start windows any suggest
ipl.1.01
spl 140 olipro
londere said:
after update my hermes my phone dosent start windows after another upfate with a shipped rom the phone finish the update but stil dident start windows any suggest
ipl.1.01
spl 140 olipro
Click to expand...
Click to collapse
You might need to reflash it. Hold the two soft keys and then push the reset button. it will ask to hard reset. If the phone fails to come on after the hard reset, then hold the left 'ok' key and the power button, and then push the reset under the phone- this will take you to a tricolor screen where you can then re-flash the phone. try reflashing with official rom's, before using any other roms.
yes i do but it still in boot any sugest ipl 1.01 spl 1.40 olipro if any know how to update ipl with hard spl or how to remove hard spl it will be aprecible
My suggestion would be to try using sd to reflash the rom and see if that orks. format sd card making sure its fat 32 then put .nbh file in root directory. rename to herimg.nbh then insert into phone. go to bootloader and it should start the flash straight away. if this works make sure you upgrade spl to olipro 2.10 hard spl so its easier if there are problems. you can possibly upgrade spl this way too (get nbh file and rename hermimg.nbh). I tried this on my herme 100 and it seemed to work. it will flash the spl BUT when it restarts it will go straight to bootloader and start flashing again. as soon as it restarts get the sd card out and put on the os you want to flash. insert card and as long as you've named it hermimg.nbh it should flash new os with spl olipro 2.10. Good luck flashing.
You should read the wiki first : http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
your phone can be unbricked using the information on wiki.
only enter to bootloader the ipl dosent start also i fla**** but it stil apear spl.140oli whei in flash it with hard spl 1.10 and when i flash it with spl 2.60 oli it send me a error i try to flash it with qtek-cingular-doppod roms and nothing any suggest
any fu**ing suggest?
also it avoid me to update spl im stuck on hard spl 1.40 and ipl 1.04 i try to flash hspl 260-210 but it refiuses to stay in 1.40 radio 1.27 patched the ipl works but it frezzes with the green led dosent apear nothing
my device still blocked in boot mode i dont know if it is briked the device had the following info
ipl 1.04
spl1.40 oli
radio maybe no
os no
any suggest
any sugest to save my hermes
follow the unbrick guide link that koorosh_bsboys posted
it cant be unlocked its stuck in spl 140 olipro
did you follow the unbrick guide that koorosh_bsboys posted?
just stop trying any unauthorised ideas. let me know if i can help u. i have a friend in o2 service centre here in india. he can get ur device working. he does it by help of a software and 3 cables . it takes about 2 hrs. just let me know if u want ur device to work again
stil zombie my device im getting crazy any ideas
londere said:
stil zombie my device im getting crazy any ideas
Click to expand...
Click to collapse
If you want people to help you, you have to help yourself first!
1st of all, have you gone to read the Wiki as suggested?
2nd what methods have you tried to unbrick your device?
If you can't answer these questions then we can not help you, you keep asking for suggestions but you do not even reply to other's questions!
Here's a good place to start helping yourself if you haven't already http://forum.xda-developers.com/showpost.php?p=1465974&postcount=1
anyone know what rom is compatible with athe100 SPL 1.10 ?
i know theirs lots of 1.2 and 3.5 spl roms, i tryed to flash a 3.5spl on my phone and now only way i can turn on the phone is in bootloader, i try to flash the phone but it always gets stuck at 1%, can anyone assist me?
cowballz69 said:
anyone know what rom is compatible with athe100 SPL 1.10 ?
i know theirs lots of 1.2 and 3.5 spl roms, i tryed to flash a 3.5spl on my phone and now only way i can turn on the phone is in bootloader, i try to flash the phone but it always gets stuck at 1%, can anyone assist me?
Click to expand...
Click to collapse
Have you took the sim card and memory card out?????
Jay
yes they are both out when tryign to flash, been over a week with out a working athena
cowballz69 said:
yes they are both out when tryign to flash, been over a week with out a working athena
Click to expand...
Click to collapse
try flashing your original ROM which should be found in the wiki section.
ignore what I said below and report back if you were able to load your original ROM
***Ignore this read above**Once your phone is working , do the athena wrapper which should load SPL 1.2
Also read this
http://forum.xda-developers.com/showthread.php?t=429013
yes I tryed to flash the original rom (its a wm5 i beleive to), still gets error after 1%,, downloaded both on the wiki and the ftp site, =\ been over a week so far no clues on why i cant flash, i even tryed to change the mac address using mtty, but instead of going into level = 0 , i get level = FF witch means the phone is locked out from flashing anything threw mtty,
thank u guys so much for responding on my issue
I also tryed doing the unlocker and its a no go
If the error when it stops at 1% is "invalid model id" the solution is here http://forum.xda-developers.com/showpost.php?p=2154726&postcount=33
cowballz69 said:
yes I tryed to flash the original rom (its a wm5 i beleive to), still gets error after 1%,, downloaded both on the wiki and the ftp site, =\ been over a week so far no clues on why i cant flash, i even tryed to change the mac address using mtty, but instead of going into level = 0 , i get level = FF witch means the phone is locked out from flashing anything threw mtty,
thank u guys so much for responding on my issue
I also tryed doing the unlocker and its a no go
Click to expand...
Click to collapse
I think this means your phone is not unlocked
with respect to sergiopi , you cant do the mtty script.
I would suggest you msg cmonex or try to talk to her on IRC on the
dxa-devs channel
addendum
seeing that you have nothing to lose, why dont you try flashing the original rom from the sd card using the method in the wiki
cowballz69 said:
anyone know what rom is compatible with athe100 SPL 1.10 ?
i know theirs lots of 1.2 and 3.5 spl roms, i tryed to flash a 3.5spl on my phone and now only way i can turn on the phone is in bootloader, i try to flash the phone but it always gets stuck at 1%, can anyone assist me?
Click to expand...
Click to collapse
I have the same problem.
what I do...
I have ameo t-mobile...windows mobile 5.0
run AthenaUnlocker
Step 1 make all finish noc problem
Step 2 hung up on 60 %
bootloader no problem....but can´t flash original flash always stuck at 1% and reboot...
flashing the original rom from the sd card using the method in the wiki ...
make it, but no do...on screen see
cheking...
loading....
than come on screen
0002802
ching...
loading...
not allowed
sergiopi said:
If the error when it stops at 1% is "invalid model id" the solution is here http://forum.xda-developers.com/showpost.php?p=2154726&postcount=33
Click to expand...
Click to collapse
My error when it stops at 1% is "invalid vender id"
my image version is demaged
Re: Ameo from t-Mobile german - repair
________________________________________
hi
what is your CID? use mtty command "info 2" to find out.
for example, if it is TMOB_007, you have to find a shipped athena rom with that CID.
if you cannot find a matching rom, let me know, i can still help,
cmonex
HTCS Þ?ÒtHTCE
please need halp
thx
felix999
read this post http://forum.xda-developers.com/showpost.php?p=2154726&postcount=33
read this post which tells you how to run mtty
follow the instructions to start mtty then press enter to get the cmd prompt
then type info 2 to get your CID
depending on this you will be able to flash the apprpriate ROM
lakeman said:
read this post which tells you how to run mtty
follow the instructions to start mtty then press enter to get the cmd prompt
then type info 2 to get your CID
depending on this you will be able to flash the apprpriate ROM
Click to expand...
Click to collapse
in mtty this can read:
when type task 32
become LEVEL: FF
when type info 2:
HTCS Þ?ÒtHTCE
my CID is 1.1
on bootscreen can see this:
ATHE100
IPL-v1.00
ATHE100
SPL-v1.10.RP00
what I do before...
Ameo WM 5.0 >>>>my mistake not update to WM6.0
run AthenaUnlocker
STEP1>>>OK
STEP2>>>by 60 % hang and stopped....
and now have the big problems.....Image ROM of t-Mobile 5.0 german demaged
can´t flash any rom´s
thx for hel or I want to pay bucks for service, when ma ameo live again...
felix999
lakeman said:
read this post which tells you how to run mtty
follow the instructions to start mtty then press enter to get the cmd prompt
then type info 2 to get your CID
depending on this you will be able to flash the apprpriate ROM
Click to expand...
Click to collapse
this is my CID
Cmd>info 2
info 2
Wait interpreter timeout
HTCS Þ?ÒtHTCE
????????
don´t know
felix999
Athena mobile 6 > SPL 1.10
become today a answer from crazy cat, that olipro say must take an rom in athena forum....
I flaswh with so many roms...anytime same error: error 294 - invalid vendor ID.....
My SPL 1.10 >>> can´t find a rom with SPL 1.10
what rom can repair my demaged ameo?????
thx for help
felix999
problem solved with ONLINEHELP from>>>>>cmonex>>>><<:::::>><<:::E:::>><<:::R:::>><<:::F:::>><<:::E:::>><<:::C:::>><<:::T:::>>
thx
felix999
lakeman said:
try flashing your original ROM which should be found in the wiki section.
Click to expand...
Click to collapse
Is this how you solved your problem?
Hi, I was unlocking my htc 8525 at&t but i was using vista and my cell keep in Type 2a: When the phone boots, it goes directly to bootloader mode (tri-color screen)
what can I do to fix it... tks
Whats the info for your SPL?
Hi, I got my Hermes 8525 in boot mode what i did is to install this Schaps_WM6Pro_WWE_4.00_Full.exe now my hermes is working but i want to unlock it..what can I do cos everytime i try got in to boot mode again..any help tks.,..
SPL- 1.40
Try unlocking it with Windows XP
hi, i tried in win xp but keep the same in boot mode...
On the PC, in activesync settings, untick "Allow USB Connection".
Put Hermes into bootloader (tri-colour screen) and then run the RUU_Wrapper.exe file of the unlocker program. Follow all the instructions to unlock your Hermes and once its unlocked put Hard SPL V7 on it BEFORE flashing any thing else. After flashing Hard SPL V7, go back to bootloader and check SPL is 2.10 oli.
You now have a Hermes that is easier to recover if somehing goes wrong with a flash, excluding radio rom flashes.
Cheers...
Hi, canu put the link of the program u told me to use..tks for your help..
RUU_Wrapper.exe, Its included in any rom you want to flash. Its how you flash using the PC...
Hard SPL is in the sticky of the Hard SPl thread in upgrading section.
i bricked my device back to spl 1.20 from 3.xx because the wifi and gsm antenna's didn't work after flashing it to AP 4.0! .. so i decided to flash spl back to 1.2 since my phone is X7500 . After downgrading SPL , i cannot flash to ANY ROM , HELP!!!...
http://forum.xda-developers.com/showpost.php?p=2154726&postcount=33 <<look
tried this, didn't work on my X7500
maybe you should try to flash a rom from sd-card.
download a original wm6 or wm5 rom, extract it, rename ruu_signed.nbh to ATHEIMG.nbh, copy to a fat32-formatted sd-card, insert it to your device, press and hold camera-button and softreset
please do not use a sdhc-card
bilalperwaiz said:
i bricked my device back to spl 1.20 from 3.xx because the wifi and gsm antenna's didn't work after flashing it to AP 4.0! .. so i decided to flash spl back to 1.2 since my phone is X7500 . After downgrading SPL , i cannot flash to ANY ROM , HELP!!!...
Click to expand...
Click to collapse
xacsx solution was for the lost wifi
Can you get into bootloader and what do you see?
and does any os boot up?
edit posted simultaneously with xacsx above.
My question is stillvalid
when i'm in the bootloader it shows the tricolour screen and IPL -v1.00 and SPL-v1.20 Olipro
I tried loading a ROM from the bootloader but it shows weird characters and says that this rom cannot be loaded on this device.
bilalperwaiz said:
I tried loading a ROM from the bootloader but it shows weird characters and says that this rom cannot be loaded on this device.
Click to expand...
Click to collapse
did you manage to do cmonexs mtty solution?
Have you got your athena working again?
yes i finally got my athena working!.. i realized that i wasn't running mtty as Administrator in Vista, i did that and VOILA! everythings solved, and im running AP4 now.