Alright, so im trying to superCID my Dopod 838 Pro. I've read the wiki and all the threads that i can find, and everything seems to go according to plan. Except i cannot verify SuperCID status.
I downloaded pofs http://pof.eslack.org/hermes-unlocker/
I flashed the radio, and received the "Upgrade Error 114" as expected.
I then ran HERM_Unlock_v2a.exe on the device, and after a minute i get a "Your device was SUCCESSFULLY unlocked and changed to SuperCID." message.
From mtty (after booting the device into the bootloader) i get the following results from the suggested commands.
USB>task 32
Level = FF
USB>info 2
HTCSDOPOD001Û<wHTCEUSB>
From what i understand, my device is still CIDlocked.
I want to make sure that superCID is enabled before i go flashing the ROM.
I've gone back and reread the instructions and repeated this procedure three times now.
Any suggestions as to what i might be doing wrong?
In the bootloader i see the following:
HERM100
IPL-1.01
SPL-1.04
thanks/Richard.
What radio version do you have currently installed? When you run the downgrade to radio 1.16 (attached to the unlock v2a) and get a error 114 you have to rerun it till the red progress bar appears and the radio is flashed to 1.16. Only then can you run superCID.
I have radio version: 1.06.00.10 installed.
Other versions are:
ROM Version: 1.23.707.4
ROM date : 07/21/06
Protocol version: 32.37.7010.01H
I see. Is the red bar to appear on the computer or the device? I received error 114 every time.
edit: when updating i see "Upgrade. Radio Stack. Please wait..." on the device. This message doesnt go away, even after error 114 , until i soft reset the device.
I've rerun it now an additional 5 times. I get no red bar.
Also, it wouldn't be a downgrade of the radio, as im trying to go from 1.06 to 1.16, but im not sure thats relevant.
does nobody have any insight to share?
littlenarf said:
does nobody have any insight to share?
Click to expand...
Click to collapse
I see you tried the unlocker v2a, have you tried the new version 3...just a thought.
Related
Guys
I just got my TyTN (unlocked, stock TyTN, HERM200, HT636 series) yesterday. Device info as follows:
ROM version: 1.18.255.3
ROM date: 07/22/06
Radio version: 1.03.03.10
Protocol version: 32.34.7010.01H
ExtROM version: 1.18.255.106
I am on Cingular and in the Washington DC area.
I was trying to flash the Radio only to 1.16 because I am having issues connecting to the Cingular UMTS network, as per the wiki site (http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms). Here's what happened:
a. I ran the upgrade file.
b. The device got into the bootloader mode (tricolor screen) successfully
c. Then the upgrade utility gave me the following error:
ERROR 120: COUNTRY ID ERROR
The ROM image that you are trying to use is not designed to work with your device. Please check the vendor website and download the correct ROM update.
Click Exit to quit
(attached screenshot)
d. I clicked Exit. The device remained in the Bootloader mode (tricolor).
e. I then removed the battery and restarted it.
Thankfully, the device started working properly after starting up.
Any thoughts regarding what's going on? Why was I not able to update my Radio?
I will really appreciate any help in this regards.
JoKer
tried to run the upgrade twice when you get the error? without disconnecting the device from usb...
No pof ... I haven't .. I disconnected it before restarting it. What exactly should I do this time?
gravejoker said:
a. I ran the upgrade file.
b. The device got into the bootloader mode (tricolor screen) successfully
c. Then the upgrade utility gave me the following error: ERROR 120: COUNTRY ID ERROR
d. I clicked Exit. The device remained in the Bootloader mode (tricolor).
e. I then removed the battery and restarted it.
Click to expand...
Click to collapse
Everything ok until "d", don't do "e". Go to "a" again.
I followed all of above steps with my stock TyTN. Fired up the upgrade again after the country ID error, I get the white screen indicating a radio upgrade is being performed. After a while I get the 114 error, I reset the TyTN but the radio is still 1.03. Anything else I need to consider?
check your bootloader version. Radio upgrades can only be done with bootloader 1.04, if you have bootloader 1.06 you don't have the 'rtask' command needed to go to radio bootloader.
pof said:
check your bootloader version. Radio upgrades can only be done with bootloader 1.04, if you have bootloader 1.06 you don't have the 'rtask' command needed to go to radio bootloader.
Click to expand...
Click to collapse
Ok, I have 1.06 bootloader. I was interested in a newer radio ROM to figure out whether my old ROM prevents me from having a simultaneous voice/data connection...
Any suggestions what to do next?
Flash a ROM matching your CID with bootloader 1.04.
Read this wiki page:
http://wiki.xda-developers.com/index.php?pagename=Hermes_Howto_Bootloader104
Dear All,
I've tried to upgrade to ROM Hermes_1.18.416.1_1.18.416.101_1.14.00.10_WWE_Ship
and unluckly cable loosen and I reset the phone.
Since it's in the middle and can't success enter the Windows Mobile,
but the bootloader was updated to 1.06.
Now I can't flash any ROM either
HER_DopodAsia_1237074_1060010_WWE_SHIP or the new one.
The tools on "imei check" even can't recognize my phone.
Any one can help me on this issue, please?
Thanks in advance.
Try the steps here, let us know the results:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
If you don't fix it with the proposed solutions attach USB Monitor capture in text format as explained in the bootom of the page.
I have the same issue, and sent it to service, and now I have the phone back and they could not fix it, so got no radio or imei number, so none of the FAQ will work for me.
So I have an expensive paper weight.
Hi,
ME TOO!!
I recently had a power cut (yes, a lights off power cut!) that killed my PC half wat through installing the Cingular English CWS__001 1.34.502.1 09/21/06 ?? 1.16.00.00 32.53.7018.01H 14955.2.3.0 ROM onto my SPV 3100.
Now SPV 3100 will boot to the ROM I was running prior to the upgrade but I can't use the telephone. I'm also not able to rerun the upgrade as it got far enough through the process to upgrade my bootloader to 1.06 - therefor rendering me unable to load another ROM.
Before the crash I was using the Imate ROM as below and M3100 was sim unlocked and running on o2 3G
i-mate English CDL__001 1.20.305.3 07/21/06 1.20.305.104 1.07.03.10 32.41.7010.02H 14955.2.3.0 1.04
I have also tried imei without any joy.
the PDA part of my M3100 still works but the phone is dead. I have been told that if you can get the latest radio installed then you satnd a chance of the phone part working.
We need a hack to get bootloader 1.4 back on the phones.
Please help.
Thanks
My one now is a photo frame which one show "HTC" or "Windows Mobile",
at least your one is a PDA.
There are nothing in "info 2" and so nothing can be flash into it.
Is it possible to have something written CID and IMEI to phone in mtty
and let the flash rom success?
i am in the same situation like yhlee. Pof, i have reply your pm and ready to upload the result file to FTP. where should i upload to?
Thanks
oh i forgot to say, mine is even worst. as soon as i turn on the unit. it will go right into bootloader without press any button.
The USB Log is too large (around 2MB)
and can't upload, any suggestion?
Thanks.
rnc1688 said:
oh i forgot to say, mine is even worst. as soon as i turn on the unit. it will go right into bootloader without press any button.
Click to expand...
Click to collapse
This can be fixed by bootloader commands 'set 14 0' and 'task 8', will reboot your device and boot into OS again (but no GSM yet!)
yhlee said:
The USB Log is too large (around 2MB)
and can't upload, any suggestion?
Click to expand...
Click to collapse
Upload it to xda-developers ftp:
ftp://xdaupload:[email protected]/Uploads/Hermes/
USER: xdaupload
PASS: xda
POF, file have been uploaded, file name= rnc1688
Thanks
'set 14 0' and 'task 8' didn't work
@rnc1688: It starts the flashing process, but you get a "CID not allow (255)" error because your CID is corrupted and you are in bootloader 1.06.
Is not booting WM5 after "set 14 0" in mtty.exe? If it's not booting WM5 you'll not be able to flash bootloader 1.04 and bypass CID checking.
so i guess my unit is bricked now.
I've upload the file which named yhlee.txt.
However, I'm going to send the unit for service.
Hope they can fix.
Any way to make it show the bootloader screen on start-up
everytime?
"set 14 1" doesn't work after push the RESET button.
Thanks.
@yhlee: U're getting exactly the same error as rnc1688. Device in bootloader 1.06 which has corrupted CID, however you say you can go into OS, so it would be possible for you to downgrade the bootloader so it does not enforce CID checking.
yhlee said:
Any way to make it show the bootloader screen on start-up everytime? "set 14 1" doesn't work after push the RESET button.
Click to expand...
Click to collapse
Try "set 1e 1" and then "set 14 1", you'll boot stright into bootloader.
@rnc1688: If you want to go WM5 try this:
"set 1e 1" and then "set 14 0", you should be able to boot stright into OS.
no luck either
grrr!!!... command "set 14 [0|1]" is working fine in 1.04 here to switch boot into WM5 or boot in bootloader mode... probably different in 1.06??? I don't have a 1.06 now to test
Mine one is just showing "Windows Mobile" but stuck there,
but seems rnc1688 one is a PDA but my one is nothing.
I've sent to distributor for service.
Thanks you pof.
yhlee said:
I've sent to distributor for service.
Click to expand...
Click to collapse
Let me know when they fix it... i'm curious about if they will fix it with 1.06 or they will downgrade to 1.04 first.
I got a correct message back from the service company, and they will not fix a bootloader 1.06 unless the original rom has been release with it, I was told that is HTC policy on this.
Using XP, I am trying to upgrade from radio 1.16.00.00 to radio 1.20.31.10. I have followed the instructions in the Hermes Upgrade Guide to the letter. I have tried sever times, but I continue to get ERROR 114. Each time the phone says "Upgrade Radio Stack Please Wait..." and the upgrading process never moves from 0% on the desktop (yes, I closed process wcescomm.exe before starting.) I have also tried doing another upgrade right after the error 114 message, without disconnecting the phone nor reseting, but I get ERROR 150.
Any ideas would be helpful.
Ron
Current Setup:
ROM: 1.34.502.1 Cingular
Radio: 1.16.00.00
BL: 1.04
Task 32: 0
History:
1) Phone came loaded with Cingular ROM 1.34
2) Downgraded to Cingular ROM 1.30 to get BL1.04
3) SuperCID unlock automatically with HTC_Hermes_SIM_CID_Unlock_v3 (GREAT PROGRAM!!!)
4) Used SSPL-HERM.exe to change ROM back to Cingular 1.34
5) UNSUCCESSFULLY tried to upgrade Radio Version to 1.20
Well, I was doing everything right... but my computer was refusing to cooperate with me. Because I did the exact same thing on my wifes computer and it worked!!!
Thanks
Ron
He Guys,
Just my luck I have bought an HTC Tytn with the original Dutch rom and sim unlocked second hand.
I wanted to put a new Dutch rom from HTC on it but I keep on getting the ERROR [244] : INVALID MODEL ID but what I don`t understand is I have used the original Dutch rom from HTC. So I checked the device information and under the tab identity it says;
Model No.: H
Platform: PocketPC
IMEI: xxxxxxxxxxxxxxxxxxx
Shouldn’t the Model No. be HERM200?
Has anyone any suggestions in how I can solve this problem so I can flash any rom I wish.
I have tried al the cid unlock programs I could find and in bootloader it says;
H
IPL-1.01
H
SPL-1.40.Olipro
Thanks in advanced.
Use RAR to unpack the Original Dutch ROM.
Take the NBH file that you get when you unpack the ROM.
Put it in a folder with CUSTOM_RUU from Olipro.
Run CUSTOM_RUU and it will load up the ROM from the NBH file, bypassing the CID check. Should work
Thanks for the reply,
I have tried what you suggested but I still get ERROR [244] : INVALID MODEL ID I have also read these posts http://forum.xda-developers.com/showthread.php?t=322231&highlight=CUSTOM_RUU+from+Olipro and http://forum.xda-developers.com/showthread.php?t=322119&highlight=CUSTOM_RUU+from+Olipro and http://forum.xda-developers.com/showthread.php?t=309707&highlight=CUSTOM_RUU+from+Olipro and tried these suggestions but every time I get the error message. The radio update process was the same for me it will go to 7% and then give the message ERROR [244] : INVALID MODEL ID.
I have also tried the HTC_Hermes_SIM_CID_Unlock_v3a and Hard-SPL-V7 but still get the error message.
I hope I’m doing something wrong if not then I hope you have a new suggestion.
Thanks in advance.
Please set your device in BOOTLOADER MODE and post here your IPL / SPL versions.
Junner2003 said:
Please set your device in BOOTLOADER MODE and post here your IPL / SPL versions.
Click to expand...
Click to collapse
Did you read first post?
VivaErBetis said:
Did you read first post?
Click to expand...
Click to collapse
Ups, missed the bottom - thought it is the signature already! Sorry, haven't had my coffee yet!
Well, looks like the device is CID unlocked!
How about trying to flash an entire cooked ROM?
i would suggest the following:
flash a cooked rom (any)
see if that makes any difference to your model id
then try and flash the native dutch rom
good luck
Hi Guys,
As you suggested I tried a cooked rom the Hermes_WM6_vanilla still get the same error message when I put my device manually in boot loader it shows;
H
IPL-1.01
H
SPL-1.40.Olipro
But as soon as I try an official or cooked rom it shows;
H
IPL-SSPL by des
H
SPL-1.09.ds
I’m now trying Schaps_WM6Pro_WWE_4.00_Full_Beta3.exe and choose for auto detect and it said 1.40 Olipro and in boot loader it shows;
H
IPL-1.01
H
SPL-1.40.Olipro
And after 1% I got the ERROR [244] : INVALID MODEL ID message again.
I think my options are getting slim.
Your ModelID is stored on NAND and can be edited quite trivially (mostly).
how it got corrupted I don't know, however, the important question is; can you get into the OS?
He Olipro,
The device it zelf works perfect I can go anywhere I want even in the OS.
Just lead the way.
Changing Model ID
I have a similar problem in that my Model ID got corrupted during a radio upgrade. I now get the same error (244) and am stuck on SPL2.10 and can't downgrade to fix it. Can anyone tell us how to manually change the model ID in the NAND?
Much appreciated.
Dumping NAND
Ok, I'm a relative newbie so appologies before I get flamed. Thanks Olipro for giving me a clue.
I have now got spl 2.60 on my device but am unsure how to dump the NAND. I've worked out how to dump the 3 partitions from the device to dump the OS but am still unclear which part of the device is the NAND. I've read the Wiki on the memory map but am still not too sure.
Anyone able to give me simple instructions to dump the NAND and once I've done that where abouts is the ModelID stored? Do I do this using mtty?
Thanks in advance.
http://forum.xda-developers.com/showthread.php?t=322225
NAND Dump
Thanks Drummer for pointing me in the right direction.
Ive done this bit:
BTW, if you want to do a full backup of you FULL eeprom nand at any time, connect as before and type these commands:
plink HERMES > full.nb (hit ENTER twice)
task 32 (hit ENTER once and only once from now on after every command)
password 0000000000000000 - My device password is BsaD5SeoA which I used instead.
set 1e 1
rbmc me.txt 50000000 7fff800
watch your file grow to 128 MB.
It creates a full.nb file but it stays at 1k!!
** Note I have copied the bootloader file for spl 2.60 on my Hermes and ran that so I can now use that versino instead of the 2.10 thats on my device if that makes a difference and have tried with no joy with either version. Yes I know it says to use 2.30 but I can't work out how to get that on my device due to the ModelID error.
The Model number is contained within the herm1.nb file that was posted by BusStop in that thread. No need for complete NAND reflashing, only that section. You'll see it using a Hex Editor. You should write down your WiFi MAC addess, so you can edit it before flashing the file with the corrected Model number. Now you just have to figure out how to get SPL 1.01 MFG on your device...
Thanks Drummer. I did try flashing the herm1.nb file but of course as I do not have SPL 1.01 MFG it gievs an error. I'll keep trawling through the site and see if I can work out how to get SPL 1.01 onto my device. I'm not going to let this damn device beat me.
Ok so I worked out how to get the ModelID using getdevicedata. Used nbhtool to create a vaild nbh using the ModelID I'd just got and used the spl from 2.30 and it updated that fine.
Excellent.
However did the same with the MFG1.01 and flashed it and......
I now have a dead brick, no power and no response form usb. Time to get a replacement device.
Thanks for all the help I've had. I'm sure it should have worked.
1.) Remove battery
2.) Connect Hermes to charger or USB
3.) Insert the battery while Hermes is connected to charger
4.) Red light should turn Amber
5.) Soft Reset
Thanks for the advice Drummer however:
1.) Remove battery
2.) Connect Hermes to charger or USB
3.) Insert the battery while Hermes is connected to charger
4.) Red light should turn Amber - Nope red light goes out!
Mne shows HHHHHHH
Hi all, i've upgraded my radio and after my model id changed to H.
So, reading some posts i've used NBHTOOL.
1.I've decompiled an original Italian ROM
2.i've obtained a custom nbh selecting only OS and EXTROM and changing my Model number.
3. after that i've flashed the nbh resulting into a write error at 84% and a bricked htc.
Luckily i was able to reflash roms and i processed to second experiment.
I've made a custom rom with only the os, and it WORKED!
so my questions are:
1. can i use my htc even if my external rom isn't flashed (it cames from an old Schaps 4.0 succesful flash)
2. It is safe to proceed installing bootloader SPL using the nbhtool like i did with the os?
In that case i will be able to fix the model id problem by flashinh spl 1.01 and using the wireless fixing method you posted..
Thanks in advance for your reply!
Hi
From my understanding the Ext rom is mainly used for carriers to install there specific addons and customizations so it shouldn't be a problem.
As you can see I did flash spl 2.30 using this method and it worked fine ti was only when something whent wrong flashing 1.01 that my problem happened but I think that may be that I used an nbs file instead of an nb file from what I've read since.
Good luck.
Edit: Just noticed someone on this thread has managed it by going straight ot 2.60 http://forum.xda-developers.com/showthread.php?t=322225
I Have read allot of data, unbrick tutorials and upgrades suggestions...
but I Still haven't found what is the correct upgrade stages.
As far as I have read from the unbrick suggestions, I've reached to the following order:
1) Upgrading SPL (Enabling KITL)
2) Unlocking
3) Upgrading radio
4) Upgrading Windows
Can someone confirm or recommend/add other steps ?
During the upgrade steps, will the HERMES be usable ?
Unlock first THEN hard spl.
DONT mess with your radio if it works fine, as this is part that can COMPLETELY brick your phone(you may be able to use as a PDA but not gonna be a phone EVER again.)
Load an os(either a stock one OR one of the cooked roms our TOP chefs cook up.), most come as OS only, no radio.
Hope this helps.... Cheers
It is useless for me, I cannot unlock the phone, due to different locking technique.
there are few posts about a locked Jasjam, with no olutions.
all the unlocking process went well, 3 times...
after the unlock process, when I insert the sim, it connects to the network, (indicated with 5 lines) and after about 5 seconds, it disconnect and says :
"The system detected an invalid SIM card"
and asks for unlock code.
now I have the following versions:
IPL 1.01
SPL 1.40.Olipro
Radio 1.16
any ideas ?
The Solution
To unlock Cellcom (Israel) JASJAM, As weird as it sounds, you should disable/deactivate/uninstall/whatever the EYRON Multi language support, which comes pre-installed.
I'll let the experts explain it.
I Dont know if it works for Orange-il Tytn too.
please consider note this in unlock guide ?
Now, which version of HARD-SPL with KITL should I Install... (Link will be helpful)
Please note that I Only Unlock the SIM, and not SuperCID, the .BAT file of the unlocker says:
"CID Unlock: will make your phone SuperCID forever, don't check this if you are unsure. HardSPL will do same effect without loosing warranty."
Olipro ver 7(Hard SPL) This is considered the best for the layman, if you want to develope roms/ programs then you should use ver 9. However, ver. 9 does throw up an error after flashing. There is no problem and olipro said he'd get around to fixing it, BUT.......
Hope this helps...
ultramag69 said:
Olipro ver 7(Hard SPL) This is considered the best for the layman, if you want to develope roms/ programs then you should use ver 9. However, ver. 9 does throw up an error after flashing. There is no problem and olipro said he'd get around to fixing it, BUT.......
Hope this helps...
Click to expand...
Click to collapse
I have upgraded to Olipro V7
When I Boot into bootloader, I see:
IPL-1.04
SPL-2.10.Olipro
But I Still not get any sign of KITL according to this threat (Step 5).
The Device is booting normally, as if I'm not holding any bottons.
How can I check if KITL enabled ?
Do I need KITL while using OLIPRO V7 ?
Orenk,
Have you read the Mr Vanx guides or the wiki? Here are the links:
http://www.mrvanx.org/cms/
http://wiki.xda-developers.com/
WB