Hey Gang,
Got a Cingular 8525 with the following symptoms:
1) Was SuperCID + SIM Unlocked
2) Was on Cingular 1.35 + Radio 1.27; attempted upgrade to Cingular 2.06 (.exe, full rom). Upgrade failed at the 25% point.
3) Boot loader got updated to 1.09
4) On power-up, phone displays AT&T splash screen with "No GSM", then hangs at Windows Mobile splash screen.
5) When I attempt to try a new ROM .exe (or re-run the Cingular one), or downgrade the Boot Loader, or anything from the tri-colored screen, the (win32) software returns an "INVALID VENDER" error,
which makes me wonder if the SuperCID status somehow got corrupted.
6) 'info 8' from the MTTY USB serial console shows that all blocks are present and in good condition.
As this is my sole phone, this really leaves me in a bad spot. I'd like to see if there's anything I can do to salvage it before waiting potentially a couple of days for
Cingular to ship me a replacement -- and that's assuming they will.
Any advice would be greatly appreciated.
fyi: USB>info 2
CID: Wait interpreter timeout
HTCSF kEØ(HTCEUSB>
USB>info 2
HTCSF kEØ(HTCEUSB>
USB>
USB>info 2
CID: Wait interpreter timeout
HTCSF kEØ(HTCEUSB>
USB>info 2
HTCSF kEØ(HTCEUSB>
USB>
USB>info 1
USB>info 2
HTCSF kEØ(HTCEUSB>info 3
HTCSH
Is this phone salvageable or not?
Anybody out there? pof? sleuth225?
dolemite said:
fyi: USB>info 2
CID: Wait interpreter timeout
HTCSF kEØ(HTCEUSB>
USB>info 2
HTCSF kEØ(HTCEUSB>
USB>
USB>info 2
CID: Wait interpreter timeout
HTCSF kEØ(HTCEUSB>
USB>info 2
HTCSF kEØ(HTCEUSB>
USB>
USB>info 1
USB>info 2
HTCSF kEØ(HTCEUSB>info 3
HTCSH
Is this phone salvageable or not?
Click to expand...
Click to collapse
ME TOO...
who can help us?
If you bothered to read the Wiki, you would have seen this:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#problem5
If you can't bother to read the wiki, don't play with roms!
LegolasTheElf said:
If you bothered to read the Wiki, you would have seen this:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#problem5
If you can't bother to read the wiki, don't play with roms!
Click to expand...
Click to collapse
Actually, I did read that, and a couple of problems:
1) Boot Loader is 1.09
2) OS won't load, so can't use any of the ActiveSync-based methods for downgrading to an older version, such as 1.04.
3) CID appears to be corrupted, as per the earlier output pasted.
Any brilliant ideas, or is my phone effectively bricked beyond repair?
Thanks...
the wiki that LegolasTheElf told you to review does in fact say what to do if you have bootloader 1.09 and can't boot into the OS to run SSPL...
8. If your bootloader version is different than 1.04 then Flash Bootloader version 1.04
on that page, you are told the following:
If no such rom is available for your device or your bootloader version is 1.09, you can buy the Imei-check unlocker to have bootloader 1.04. The HTC Hermes unlocker from imei-check is able to flash the 1.04 bootloader. It transfers the required files to the Hermes via ActiveSync before actually the unlocking key file with your IMEI is requested. The bootloader is flashed on the device after you enter the valid key file (you have to pay for that).
[edit: fixed incorrect bold formatting tags]
[edit 2: well, apparently i can't read. the text i linked definitely says it needs to transfer files via activesync, and of course you can't do that. sorry...been a long day. is it 5pm yet?]
Pretty much. No working OS, hence no ActiveSync. And the CID appears corrupt, so it's not like I can just downgrade to 1.01/1.04 from the boot loader.
Anybody want to drop some science on me? Cause it sounds as though I might be screwed...
yes, u are screwed! just like me! just get another one on ebay!
people keep saying DOWNGRADE to bootloader 1.04! but it' not possible if u have bootloader 1.09 and u stuck at the boot-up screen!
Sam case with me.
Related
Please help me!
I screwed my german T- Mobile MDA Vario II. I used HTC universal sim unlocker and I haven’t got radio. I know I was a craze.
No GSM, no cid and no imei. The pda is working good.
I vas very happy when I find this site :
http://wiki.xda-developers.com/index...pgradeProblems.
The radio doesn’t work , no GSM, no cid and no imei. The pda is working good.
Please help me
At least your device is on bootloader 1.04
have you tried all the steps in "problem 5" on the wiki?
What the "MDA Vario II" is equipped with that one of "bootloader" 1.04 and I have done everything under "problem 5" unfortunately without steht. is carried out.
USB>info 2
CID: Wait interpreter timeout
HTCSF kEØ(HTCEUSB>
USB>
USB>info 3
CID: Wait interpreter timeout
HTCSHUSB>
USB>info 7
HTC Integrated Re-Flash Utility, Common Base Version : 1.50a
Device Name: H, Bootloader Version : 1.04
Built at: May 26 2006 20:17:35
Copyright (c) 1998-2006 High Tech Computer Corporation
CPU ID=0x41129200
Main CPLD version=0x5
USB>password 0000000000000000
HTCSInvalid password.R¿ËPHTCEUSB>set 1e1
USB>erase a0040000 c80000
HTCST ÚÈÒHTCEUSB>erase a0cc0000 c80000
HTCST ÚÈÒHTCEUSB>erase a1940000 640000
HTCST ÚÈÒHTCEUSB>set 1e 0
USB>
USB>
Upper CPLD version=0x4
Main Board version=0x6
Please help me
Try to flash a radio rom, and send me the USB Monitor capture exported in ANSI text format of all the radio rom flashing process.
Instructions for how to use USB Monitor are on the wiki "upgradin problems" page too:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
HElp me
Hello has a little lasted with me longer.
I hope you can help me at mine nevertheless problem!
Here is the ANSI file
The upgrade stops because radio bootloader doesn't answer to 'rerase' command after 3 retries. Repeat the steps on wiki "problem 5", do it several times. If you can't get it to work send it to repair centre.
hmm
would it use what if I make Rome one new completely, then?
gives it no questions possibility on the CID to circulate?
I don't understand what you mean.
Mummromeo, I also can't understand what you try to say. Send me a PM in german if you want to.
Another variation for this problem..
I am trying to recover my Smrtphone. I have a XDA First Trio. First I instaled a HTC ROM with bootloader 1.06. After I unlocked the SIM and CID. When I tried to install the ROM from Cirgular with Bootloader 1.04 the process stoped at 14% and now I have a mixed ROM with Bootloader 1.06... and I cannot unlock and install another ROM.... what I can do??? I am not an expert.. I dont know how to install DUmped Roms... I tried to follow the wiki but my device is locked and I dont know how to change the Key Entries.... HELP ME!!!! PLEASE
@rfgirardi: take any of the O2 XDA trion german ROMs found here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_Upgrades
Try to flash it while the device is in bootloader mode, if you're not successful flashing then try to flash from SD card as described here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing
Hi pof,
Thanks for your help, but the procedures doesnt function... I runnede the Devicedata.exe and the file created doesnt have the information about the device... In the bootloader i have HEM100 IPL-1.01 and SPL-1.06. In the devicedata.txt cretaed I have just this
HERM100 1 0 0 å p 1.18
If i look in the System»Settings»Device Information I have:
ROM Version: 1.18.416.1
RADIO Version: Nothing...
Protocol Version: Nothing...
IMEI: Nothing..
Do you think I can try another procedure or just send the device to the workshop?
Rodrigo
rfgirardi said:
Do you think I can try another procedure or just send the device to the workshop?
Click to expand...
Click to collapse
As you can boot OS it could be downgraded to bootloader 1.04, but with a corrupted radio.
This is what I got for updating by doing this:
"Bring your bricked TyTN back to live"
http://forum.xda-developers.com/showthread.php?t=280425
With doing this, this is the only solution that will get me far enough for the boot screen to actually go white. The rest of the Rom's or Radio's don't got anywhere past this.
I hope someone can help me, no solution anywhere? Not even the Softbank chip can help.
I answered you on this thread:
http://forum.xda-developers.com/showthread.php?p=1078913#post1078913
Please do not double-post.
pof, I think it's time for a Sticky on this matter, cause it's becoming a common issue.
axiom said:
pof, I think it's time for a Sticky on this matter, cause it's becoming a common issue.
Click to expand...
Click to collapse
Yes, great idea... will make one now and let's see if we can keep all the bricked devices in one whole sticky thread. Hopefully we find a solution by joining all our efforts
Hi Pof,
I have the Unlocker that I payed to do the first unlock. After the problem when the Upgrade Rom process stoped at 14%, the feature doesnt recognize my device as a valid one. With this feature I cannot downgrade to 1.04. I dont know more what I can do.... but anyway, thanks for your efforts!!
Hello everybody - can anyone help me at this moment. I am right now sitting with my Hermes connected through USB. I was flashing the standard ROM with RUU_HERMES_HTC_WWE_1[1].35.255.2_1.35.255.102_1.08.00.10_SHIP. Unfortunately it stopped at 5% some half an hour ago. I prefer to ask you before disconnecting it. Please help!!!!!!!!!
OK, having no answer I decided to disconnect it and look for an answer. Now I know that I have a 1000 USD brick and no possibility to put it back to work.
I now suspect that the upgrade did not work properly because my device had a CID lock. That is quite strange however, because I bought it on the open market without any commitment to any GSM operator.
I am now stuck on the tricolor bootloader screen with SPL 1,09.
Basing on the post: http://forum.xda-developers.com/showthread.php?t=285157 - especially on the lines:
"1.09
You can't downgrade to bootloader 1.04 by flashing a Shipped ROM. However imei-check.co.uk is able to downgrade the bootloader.
There was a solution posted on this forum, but it was stolen from imei-check and was removed. If you are not willing to pay you have to wait until another solution is developed.
The RadioROM can't be upgraded. You have to downgrade to bootloader 1.04 to unlock your device.", despite seeing info on the website, I paid to imei-check the 20 pounds.
So far I only lost money, time and nerves trying to downgrade or "repair" my hermes. Nothing works. If anybody has any suggestions please share on the forum or PM me.
BTW I started the whole process with SPL 1,04.
Sounds to me like a flaky USB port which is why it stopped at 5%. Try another port in the rear of your PC and re-flash. Be sure to follow the mantra:
Windows XP, screensaver, powersave disabled
No other programs running.
i had a similar problem probably with the flaky usb port as Sleuth255 mentioned. trying with a different pc is another option if you have one and that was what i did with success.
im not sure about the hermes.. but i know on the wizard as long as you could get to the bootloader screen (the RGB screen) that your device isnt bricked yet.. i would follow the other suggestions about usb ports and using different pc's, i bet you can make your $1k work for you again
Try:
Go into bootloader by pressing down both the POWER button and SIDE OK together and using the stylus at the same time to press the RESET button at the bottom.
Make sure you have disabled the USB connection in ActiveSync, before trying to connect to the bootloader:
File --> Connection settings --> uncheck "allow USB connections"
Connect your USB-Cable
Download mtty.exe. Start it and connect to USB
When you see "USB>" Type "info 2". You should get: "HTCS" + CID + (4-byte checksum) + "HTCE". Remeber what CID you have.
Look for a Shipped ROM that matches your CID
Download and flash it using a different USB-Port or PC than the last time
Afterwards you will be able to use the file that you got from imei-check. The imei-check downgrader/unlocker only works if you've got a working operating system on your device.
After typing "info 2" in mtty.exe I get the following line
HTCSF kEŘ(HTCEUSB>
Which of those is the CID? I cannot find any matching one in the Wiki.
corrupted CID by wrong flash.
OK, I have now the confirmation of the diagnosis - as I was suspecting.
Can I now have some help in the solution?
Some people succeded with the method described as "problem 5" here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
but some others don't succeed and have a brick. Try the steps on the wiki, if you are not able to fix it this way, send it to repair centre.
Following the steps from point 5 of the given website, I only get the following lines:
USB>password 0000000000000000
HTCSPass1.CMˆËHTCEUSB>
USB>set le 1
USB>erase a0040000 c80000
HTCST ÚČŇHTCEUSB>
USB>erase a0cc0000 c80000
HTCST ÚČŇHTCEUSB>
USB>erase a1940000 640000
HTCST ÚČŇHTCEUSB>
USB>set le 0
USB>
Unfortunatelly nothing changes.
I've the same problem. I was flashing the HTC 1.18.416.1 1.18.416.101 1.14.00.10 but the process has stopped to 89 % and now the phone is in bootloader mode spl- 1.06 and don't enter in windows mode !!! My cid is HTCSORANG001a#USB> I hope that i've not a brick !!!
mtadeuszak said:
Following the steps from point 5 of the given website, I only get the following lines:
[...]
Unfortunatelly nothing changes.
Click to expand...
Click to collapse
Your bootloader is 1.09 and you'll not be able to flash anything because the CID will not match. Send it to service centre.
deika95 said:
I've the same problem. I was flashing the HTC 1.18.416.1 1.18.416.101 1.14.00.10 but the process has stopped to 89 % and now the phone is in bootloader mode spl- 1.06 and don't enter in windows mode !!! My cid is HTCSORANG001a#USB> I hope that i've not a brick !!!
Click to expand...
Click to collapse
Your phone is not trashed, but there is no rom matching your CID yet. You should have cid unlocked it before flashing a rom with BL 1.06.
Try to boot OS again using "set 14 0" (see wiki, "problem 4"), if that doesn't fix it (chances are it will not), then wait until orange releases a rom upgrade with CID "ORANG001".
I've try the procedure "Problem 4" but after "write nand success" and sr it don't start. My cid is always ORANG001 with spl-1.06
pof said:
Your bootloader is 1.09 and you'll not be able to flash anything because the CID will not match. Send it to service centre.
Your phone is not trashed, but there is no rom matching your CID yet. You should have cid unlocked it before flashing a rom with BL 1.06.
Try to boot OS again using "set 14 0" (see wiki, "problem 4"), if that doesn't fix it (chances are it will not), then wait until orange releases a rom upgrade with CID "ORANG001".
Click to expand...
Click to collapse
Please Pof try to help me. Where can i find that rom ? Thanks
You can't find it at the moment. It's not released yet
sn00x said:
You can't find it at the moment. It's not released yet
Click to expand...
Click to collapse
But you think that it will be available ? Thanks
Yes it will surely be released I think. But nobody knows when. Perhaps tomorrow, perhaps next year.
It bet it will be listed here when it's available.
I have searched the forums and have found 1 post saying that the T-MOB005 cannot be CID unlocked ? is this still the case as the post was dated Nov2006 ?
I have tried the POF method twice (i.e. Herm CID Unlock v2a). and although it had updated the Radio to 1.16 when i enter the "info 2" command with mtty it brings back
HTCST-MOB005¼ôàŠHTCEUSB>
which means that it is not super cid unlocked.
SPL=1.04
IPL=1.01
I have also checked that the radio has been flashed correctly and it show in device id that the Radio Version is 1.16 so it certainly appears that all has worked apart from the SuperCid
When i put in a sim from another network i get a screen that " I have tried 10 times and to wait till timeout" both buttons are greyed out so i cannot input any numbers.
My T-Mobile sim still works fine.
mtty output
USB>
USB>info 2
HTCST-MOB005¼ôàŠHTCEUSB>
USB>
USB>rtask b
0
0
atvl
0
[email protected]?40
@SIMLOCK= 01
0
atel
0
USB>
USB>rtask b
0
0
[email protected]=0,1,22051978
4
[email protected]=0,2,22051978
4
[email protected]=0,4,22051978
4
[email protected]=0,8,22051978
4
[email protected]=0,16,22051978
4
[email protected]=0,32,22051978
4
Any info appreciated.
Thanks
Are you sure you didn't flash extracted radio 1.16 before and that's why it's showing 1.16 on radio version now?
If your SPL is 1.04 it should work. Try flashing the patched radio again, and capture the flashing process with USB monitor if nothing changes after flashing the radio. This should help to troubleshoot why it is not working on your device.
I will start from scratch again this evening and see if it still gives the same results. I had already flashed my other vario II and this worked with no problems.
Will post my results this evening.
Thanks for your help so far.
I have absolutely no idea how I got the 1.16 radio roms mixed up but when i re-downloaded the unlocker again and used this one, everything unlocked fine first time. info 2 shows supercid.
Lesson learnt i think, dont do anything when you have been working for the last 14 hours as you tend to miss the most obvious things.
Thanks for your help.
Hi all,
I know this has been asked and answered lots of times, I have read all the wiki posts I could find, but still I'm not 100% sure that I understand correctly, hence this question.
I have a Dopod 838 Pro (Hermes) which I have SuperCID'ed and loaded with bootloader 1.09.
My ppc gets stuck on the windows mobile screen, and in addition I can see in the HTC subsplash screen the "NO GSM" indicator for a flick of a second.
I can go into bootloader and connect with mtty.
In another thread (and also in the wiki), it is suggested that the only way to get my machine back, is first to downgrade to SPL 1.04, and the only way to do this since I'm at 1.09 and no windows, is to purchase the IMEI-CHECK tool .
Am I correct in understanding this? or is there another way?
Thanks for any and all help.
Chris
No, I think you quit reading a bit soon.
With the new unlocker v3 and Des' SSPL flashing method, you no longer need to downgrade from 1.09 to flash anything. Simply find the newest version of the ROM and Radio you are trying to load and run the exe. Hard to believe, but it's really that easy.
Hi and thanks for the reply,
will the v3 unlocker work even if I cant boot my ppc and so I cant connect with activesync?
The only thing I can do, is boot into bootloader on the ppc and connect using the mtty tool.
Can I still use the method you suggest?
Thanks again,
Chris
T-mobile unlocker bootloader 1.09
chrisvor said:
Hi and thanks for the reply,
will the v3 unlocker work even if I cant boot my ppc and so I cant connect with activesync?
The only thing I can do, is boot into bootloader on the ppc and connect using the mtty tool.
Can I still use the method you suggest?
Thanks again,
Chris
Click to expand...
Click to collapse
Im having the same problem
Hi X01HT Rock....
can I ask u a favor? If you find a solution please PM me... I will do the same
thanks
Chris
you can't use the unlocker unless you can copy it to the device and run it from there.
from xda wiki
Problem 5: Device shows NO GSM when booting
* The radio stack is screwed, you don't get GSM signal and the phone says unknown SIM status
* Device won't start after trying to unlock it with HTC Universal Unlocker (HTC_Uni_SIM_Unlock_v1)
Here is how to fix it:
1. Disable activesync on your computer by right click on activesync icon -> connection settings -> uncheck "allow USB connections".
2. Put your Hermes in bootloader mode
3. Connect device to computer using USB cable.
4. Open mtty.exe and select USB port, then connect.
5. Hit enter twice, you will see the "USB>" prompt.
6.
Type the following commands (do not copy paste!!!)
USB> password 0000000000000000
USB> set 1e 1
USB> erase a0040000 c80000
USB> erase a0cc0000 c80000
USB> erase a1940000 640000
USB> set 1e 0
7. Reset your phone and put it back in bootloader mode
Click to expand...
Click to collapse
now copy unlock v3 to your phone, and run on the phone.
download radio 1.34 and run on your pc, while your device and pc is in activesync mode.
I believe all of this is in the wiki.
lpsi2000 said:
I believe all of this is in the wiki.
Click to expand...
Click to collapse
yeah, but the guy's device is locked with a 1.09 bootloader. we might need POF's help here.
please PLEASE guys, i need your help here (POF are you reading this?)
My machine was made SuperCID using v2a before all this sh*t happened and it was running smoothly.
It now seems that some of the mtty commands I read and tried to apply resulted in the SuperCID status to go away and now it's *scrambled* (info 2 results in "HTCSF kEØ(HTCE"). So now I cannot flash ANY rom into it even if I could.
I get to the bootloader (SPL 1.09) and also up to the windows mobile splash screen.
Also at the HTC subsplash I can see the "No GSM" msg for a fraction of a second.
Please help me unbrick this baby. I can't afford to buy another one
cant run the mtty that way
I have tried to run the password and every thing it I am having some problems with the communication
HTCST ÚÈÒHTCEUSB>
USB>password 0000000000000000
HTCSPass1.CMˆËHTCEUSB>set 1e 1
USB>erase a040000 c80000
HTCST ÚÈÒHTCEUSB>erase a0cc0000 c80000
HTCST ÚÈÒHTCEUSB>erase a01940000 640000
HTCST ÚÈÒHTCEUSB>set 1e 0
USB>
this is what happens then I try to rest the phone but it just goes back to whatit was doing.
I think that I have a language problem here.
chrisvor said:
My machine was made SuperCID using v2a before all this sh*t happened and it was running smoothly.
Click to expand...
Click to collapse
SuperCID unlocker v2a would not have worked on SPL 1.09. It might have said that unlocked successfully, but it wont have unlocked. Only unlocker 3 will unlock a SPL 1.09 phone. You'll have to keep hammering on the "bricked hermes" sticky. Someone will get round to helping you in a day or two.
I put this in the wrong place and cannot delete. Sorry for the misspost.
Hello,
I have seen on the Universal thread a way to completly format the device. After that lot of people who were stuck in windows mobile screen have recovered their device.
I dont know if it is working with hermes.
http://forum.xda-developers.com/showthread.php?t=289325
X01HT Rock said:
Im having the same problem
Click to expand...
Click to collapse
Me too....!!!! Can't solve this problem
.VIBE said:
you can't use the unlocker unless you can copy it to the device and run it from there.
from xda wiki
now copy unlock v3 to your phone, and run on the phone.
download radio 1.34 and run on your pc, while your device and pc is in activesync mode.
Click to expand...
Click to collapse
I did what you said before but can't solve the problem
.VIBE said:
SuperCID unlocker v2a would not have worked on SPL 1.09. It might have said that unlocked successfully, but it wont have unlocked. Only unlocker 3 will unlock a SPL 1.09 phone. You'll have to keep hammering on the "bricked hermes" sticky. Someone will get round to helping you in a day or two.
Click to expand...
Click to collapse
@.VIBE:
My original SPL at the time when I applied v2a unlocker was 1.01, and v2a unlocked it, I verified it with "info 2" in mtty just after, and also after all this mess started.
Something I did while trying to get out of this mess, changed my SuperCID status and corrupted it.
Is there a way to make it superCID again if the only thing I can connect with is mtty?
Thanks
Chris
You guys with bricked phones need to carefully read and understand ALL of the "dead hermes? corrupted radio? Post comments here" sticky!
Everything that POF currently knows on unbricking your device is in there also Superdave has some help for those who can get into KITL mode. Even then not every brick is recoverable at the moment, but you need to spend some time reading to find out!!
I've noticed that POF's not as quick as he used to be in replying to these kind of threads, I surmise he could be a little fed up with repeating the same thing over and over again, but I could be wrong.
Best of luck to you and my advice at the moment to anybody else coming across this is to SuperCID your phone and always try to keep your bootloader at SPL 1.04 (upgrade using mtty) as it makes recovering from bricked phones much easier.
Im having the same problem
There Is A Way Of Downgrading From 109.
Search Google For Downgrade_SPL Then Do This.
1. Go to Google, search for DownGrade_SPL.rar
2. Connect your tytn to PC and wait until activesync completed.
3. Run M3100v3cUnlock.exe. Once you see checking device.... in DOS box and whilte screen on your tytn, close the program (Dos box) immedaitely.
4. Run ROMUpgradeUt.exe and follow the japanese wizard to complete the boot loader downgrade.
5. Reboot your tytn and then put it into bootloader mode agian, you should see SPL-1.04. Great!
Cheers
@Mousey
You need to be able to fully boot into the OS to connect to activesync and the phones described here can't. The only other way I know of downgrading from 1.09 to 1.04 is from KITL mode which not all ROMS have. Full details are in the sticky I mentioned earlier.
FRIENDS help , I think I have the brick of all bricks I followed the wiki step by step including creating and copying the nbh file. I got as far as 70% of image loading and it hung and dropped into recovery mode but could not get passed there. I have tried all forms of reset and do not get passed bootloader screen with Herm100 IPL-1.04 and SPL-2.03. This was a imate jasjam running windows mobile 5.0 to which I tried flashing to the new HTC WWE 6.0 upgrade. I have tried running usb monitor from the link but it just gives me a series of paramters in a notice window and then dops off. I have tried another verison but it is not capturing anything.
I have tried mtty and cant even get the usb> prompt after disabling the usb connect in activesync. Please help as this was a works new unit last month and I have some major explaining to do if I cant get it sorted!
Model: Imate Jasjam
ROM Before Flash: TMO_UK_3.60.110.1_6275_1.50.00.00_108_Test
Radio Before Flash: 1.50
Bootloader Before Flash: Not sure
Flash failed at: 70%
Flashing ROM: Image Vers 3.54.255.3
CID Corrupt: Assume Yes
Radio Corrupt: Assume Yes
No GSM Error: Not got that far
Stuck In Bootloader: Yes
Stuck On Windows Mobile Splash: Not got that far
Can boot into OS: No
Tried mtty command set 14 0: Yes but not getting usb>
Tried wiki problem number 4: Yes dont get passed point 3 as as soon as powers up goes to tri colour screen. Switched from serial to usb with connect of usb cable
mtty info 2 output: cannot run
Current Device Status: unusable
Tried re running install and get error 260 and 294(AFTER 1%)and - Not getting a response from PDA!
I TRIED PB + KITL method .BUT IT FAILED AS I COULD NOT ACTIVATE KITL MODE.I BELIEVE ITS NOT ACTIVATED IN MY PDA.
I SPOKE TO TO IMATE INDIA PEOPLE , THEY REPLIED THAT THE MOTHERBOARD IS TO BE CHANGED , WHICH COSTS 60% OF THE COST OF THE PDA.
CAN ANYONE HELP WITH A BOOTLOADER V2.03 ?
WAKE UP DEVELOPERS .DO SOMETHING.
tHANKS IN ADVANCE.
the output is for :
HTC_Hermes_SIM_CID_Unlock_v3a
And
RUU_Hermes_TMO_UK_3.60.110.1_6275_1.50.00.00_108_Test repectively.
So no HardSPL before you flashed?
You should still be able to get a USB monitor from it.. regardless if the thing has been thrown off the empire state building.
What USB monitor program are you using?
MTTY Set 14 0 I beleive is for a corrupt radio stack, all that does is restore your radio stack to factory form, sounds to me like you have a hybrid brick, which is corrupet or invalid CID coupled along with a corrupt radio stack..
Madcap180 said:
MTTY Set 14 0 I beleive is for a corrupt radio stack, all that does is restore your radio stack to factory form, sounds to me like you have a hybrid brick, which is corrupet or invalid CID coupled along with a corrupt radio stack..
Click to expand...
Click to collapse
set 14 0 tells the device to skip to OS boot rather than go to bootloader (opposite of set 14 1)
what we need to ascertain is exactly what bootloader version this guy is running, and then to find out what CID he has from the bootloader.
until we get these both, I think we'll have to "assume" it's ****ed.
oh and in future, don't PM me twice, it pisses me off. so consider yourself lucky I've bothered to comment.
Cmd>
Cmd>info 2
HTCSCDL__001ÄÊìHTCE
Cmd>info 7
HTC Integrated Re-Flash Utility, Common Base Version : 1.51d
Device Name: HERM100, Bootloader Version : 2.03
Built at: Jun 16 2007 01:57:22
Copyright (c) 1998-2006 High Tech Computer Corporation
CPU ID=0x41129200
Main CPLD version=0x5
Upper CPLD version=0x4
Main Board version=0x6
Cmd>info 6
HTCST ÚÈÒHTCE
Cmd>info 5
Cmd>info 4
HTCSCDL__001ÄÊìHTCE
Cmd>info 3
HTCSH
Cmd>set 14 1
Write Nand Success
HTCST ÚÈÒHTCE
Cmd>rtask 32
Command error !!!
Cmd>rtask 28
Command error !!!
Cmd>rtask 8
Command error !!!
lastly it's not KITL enable.