Hi all,
I know this has been asked and answered lots of times, I have read all the wiki posts I could find, but still I'm not 100% sure that I understand correctly, hence this question.
I have a Dopod 838 Pro (Hermes) which I have SuperCID'ed and loaded with bootloader 1.09.
My ppc gets stuck on the windows mobile screen, and in addition I can see in the HTC subsplash screen the "NO GSM" indicator for a flick of a second.
I can go into bootloader and connect with mtty.
In another thread (and also in the wiki), it is suggested that the only way to get my machine back, is first to downgrade to SPL 1.04, and the only way to do this since I'm at 1.09 and no windows, is to purchase the IMEI-CHECK tool .
Am I correct in understanding this? or is there another way?
Thanks for any and all help.
Chris
No, I think you quit reading a bit soon.
With the new unlocker v3 and Des' SSPL flashing method, you no longer need to downgrade from 1.09 to flash anything. Simply find the newest version of the ROM and Radio you are trying to load and run the exe. Hard to believe, but it's really that easy.
Hi and thanks for the reply,
will the v3 unlocker work even if I cant boot my ppc and so I cant connect with activesync?
The only thing I can do, is boot into bootloader on the ppc and connect using the mtty tool.
Can I still use the method you suggest?
Thanks again,
Chris
T-mobile unlocker bootloader 1.09
chrisvor said:
Hi and thanks for the reply,
will the v3 unlocker work even if I cant boot my ppc and so I cant connect with activesync?
The only thing I can do, is boot into bootloader on the ppc and connect using the mtty tool.
Can I still use the method you suggest?
Thanks again,
Chris
Click to expand...
Click to collapse
Im having the same problem
Hi X01HT Rock....
can I ask u a favor? If you find a solution please PM me... I will do the same
thanks
Chris
you can't use the unlocker unless you can copy it to the device and run it from there.
from xda wiki
Problem 5: Device shows NO GSM when booting
* The radio stack is screwed, you don't get GSM signal and the phone says unknown SIM status
* Device won't start after trying to unlock it with HTC Universal Unlocker (HTC_Uni_SIM_Unlock_v1)
Here is how to fix it:
1. Disable activesync on your computer by right click on activesync icon -> connection settings -> uncheck "allow USB connections".
2. Put your Hermes in bootloader mode
3. Connect device to computer using USB cable.
4. Open mtty.exe and select USB port, then connect.
5. Hit enter twice, you will see the "USB>" prompt.
6.
Type the following commands (do not copy paste!!!)
USB> password 0000000000000000
USB> set 1e 1
USB> erase a0040000 c80000
USB> erase a0cc0000 c80000
USB> erase a1940000 640000
USB> set 1e 0
7. Reset your phone and put it back in bootloader mode
Click to expand...
Click to collapse
now copy unlock v3 to your phone, and run on the phone.
download radio 1.34 and run on your pc, while your device and pc is in activesync mode.
I believe all of this is in the wiki.
lpsi2000 said:
I believe all of this is in the wiki.
Click to expand...
Click to collapse
yeah, but the guy's device is locked with a 1.09 bootloader. we might need POF's help here.
please PLEASE guys, i need your help here (POF are you reading this?)
My machine was made SuperCID using v2a before all this sh*t happened and it was running smoothly.
It now seems that some of the mtty commands I read and tried to apply resulted in the SuperCID status to go away and now it's *scrambled* (info 2 results in "HTCSF kEØ(HTCE"). So now I cannot flash ANY rom into it even if I could.
I get to the bootloader (SPL 1.09) and also up to the windows mobile splash screen.
Also at the HTC subsplash I can see the "No GSM" msg for a fraction of a second.
Please help me unbrick this baby. I can't afford to buy another one
cant run the mtty that way
I have tried to run the password and every thing it I am having some problems with the communication
HTCST ÚÈÒHTCEUSB>
USB>password 0000000000000000
HTCSPass1.CMˆËHTCEUSB>set 1e 1
USB>erase a040000 c80000
HTCST ÚÈÒHTCEUSB>erase a0cc0000 c80000
HTCST ÚÈÒHTCEUSB>erase a01940000 640000
HTCST ÚÈÒHTCEUSB>set 1e 0
USB>
this is what happens then I try to rest the phone but it just goes back to whatit was doing.
I think that I have a language problem here.
chrisvor said:
My machine was made SuperCID using v2a before all this sh*t happened and it was running smoothly.
Click to expand...
Click to collapse
SuperCID unlocker v2a would not have worked on SPL 1.09. It might have said that unlocked successfully, but it wont have unlocked. Only unlocker 3 will unlock a SPL 1.09 phone. You'll have to keep hammering on the "bricked hermes" sticky. Someone will get round to helping you in a day or two.
I put this in the wrong place and cannot delete. Sorry for the misspost.
Hello,
I have seen on the Universal thread a way to completly format the device. After that lot of people who were stuck in windows mobile screen have recovered their device.
I dont know if it is working with hermes.
http://forum.xda-developers.com/showthread.php?t=289325
X01HT Rock said:
Im having the same problem
Click to expand...
Click to collapse
Me too....!!!! Can't solve this problem
.VIBE said:
you can't use the unlocker unless you can copy it to the device and run it from there.
from xda wiki
now copy unlock v3 to your phone, and run on the phone.
download radio 1.34 and run on your pc, while your device and pc is in activesync mode.
Click to expand...
Click to collapse
I did what you said before but can't solve the problem
.VIBE said:
SuperCID unlocker v2a would not have worked on SPL 1.09. It might have said that unlocked successfully, but it wont have unlocked. Only unlocker 3 will unlock a SPL 1.09 phone. You'll have to keep hammering on the "bricked hermes" sticky. Someone will get round to helping you in a day or two.
Click to expand...
Click to collapse
@.VIBE:
My original SPL at the time when I applied v2a unlocker was 1.01, and v2a unlocked it, I verified it with "info 2" in mtty just after, and also after all this mess started.
Something I did while trying to get out of this mess, changed my SuperCID status and corrupted it.
Is there a way to make it superCID again if the only thing I can connect with is mtty?
Thanks
Chris
You guys with bricked phones need to carefully read and understand ALL of the "dead hermes? corrupted radio? Post comments here" sticky!
Everything that POF currently knows on unbricking your device is in there also Superdave has some help for those who can get into KITL mode. Even then not every brick is recoverable at the moment, but you need to spend some time reading to find out!!
I've noticed that POF's not as quick as he used to be in replying to these kind of threads, I surmise he could be a little fed up with repeating the same thing over and over again, but I could be wrong.
Best of luck to you and my advice at the moment to anybody else coming across this is to SuperCID your phone and always try to keep your bootloader at SPL 1.04 (upgrade using mtty) as it makes recovering from bricked phones much easier.
Im having the same problem
There Is A Way Of Downgrading From 109.
Search Google For Downgrade_SPL Then Do This.
1. Go to Google, search for DownGrade_SPL.rar
2. Connect your tytn to PC and wait until activesync completed.
3. Run M3100v3cUnlock.exe. Once you see checking device.... in DOS box and whilte screen on your tytn, close the program (Dos box) immedaitely.
4. Run ROMUpgradeUt.exe and follow the japanese wizard to complete the boot loader downgrade.
5. Reboot your tytn and then put it into bootloader mode agian, you should see SPL-1.04. Great!
Cheers
@Mousey
You need to be able to fully boot into the OS to connect to activesync and the phones described here can't. The only other way I know of downgrading from 1.09 to 1.04 is from KITL mode which not all ROMS have. Full details are in the sticky I mentioned earlier.
Related
Please help me!
I screwed my MDA Vario II. I used HTC universal sim unlocker and I haven’t got radio. I know I was a craze.
No GSM, no cid and no imei. The pda is working good.
I vas very happy when I find this site :
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems.
I made this:
USB>
USB>password 0000000000000000
HTCSPass1.CMˆËHTCEUSB>set 1e1
USB>erase a0040000 c80000
HTCST ÚČŇHTCEUSB>erase a0cc0000 c80000
HTCST ÚČŇHTCEUSB>erase a1940000 640000
HTCST ÚČŇHTCEUSB>set 1e 0
USB>
The radio doesn’t work , no GSM, no cid and no imei. The pda is working good.
Please help me
Please can a expert check this!?
I found this with the search option.... can someone check this....
Its written for the Tytn and not for the Vario II, i'm not sure but i thought that the english Vario II has a 1.06 bootloader!! Then you are stuck, beacause the file who degrade your bootloader to 1.04 isnt availleble anymore. Maybe one of the guys here can share it with you?!
======================================================
- Take the battery out of your TyTN and leave it out several minutes
- Disable USB-connection in Active-Sync
- Reboot your Computer
- Replace the battery and put your TyTN in the bootloader
- Try to load the ROM found here:
ftp://xda:[email protected]/RUU120_172125_Qtek_WWE_R11400_Shipping.exe
- Keep trying till you get just past the erasing part, then you will get an error-message and are asked to reset your device with the stylus
- Reset your phone and put it back in the bootloader mode
- Install any Hermes ROM you like, no matter what CID if you have bootloader 1.04
lacika said:
The radio doesn’t work , no GSM, no cid and no imei. The pda is working good.
Click to expand...
Click to collapse
Can you attach a USB monitor capture of what happens when you try to:
a) flash a rom
b) flash a radio rom
Do both things starting from bootloader and with activesync disabled.
Same Problem
I have the same problem
My PDA keeps comming back in the bootloader screen.
When 1 try to update (its a unlockes pda), the upload stops at 1%
Is there a way to erease the PDA ?
Thanks
pimmmm said:
I have the same problem
Click to expand...
Click to collapse
I have the same questions.
Can't do anyithing if you don't attach a USB capture of the process. See this page for instructions: common upgrade problems
smarty77 said:
I found this with the search option.... can someone check this....
Its written for the Tytn and not for the Vario II, i'm not sure but i thought that the english Vario II has a 1.06 bootloader!! Then you are stuck, beacause the file who degrade your bootloader to 1.04 isnt availleble anymore. Maybe one of the guys here can share it with you?!
======================================================
Click to expand...
Click to collapse
HI!
Thank You for your answer. I made yours tip, but not was good.
First I to try smarty77 tip. I used RUU120_172125_Qtek_WWE_R11400_Shipping. Its function. After I’d like rom upgrade. This doesn’t was good (invalid vendor).
Second I to try clearing with mtty.exe.
The situation same, the phone doesn’t work.
Sorry my bad English.
pof said:
Can you attach a USB monitor capture of what happens when you try to:
a) flash a rom
b) flash a radio rom
Do both things starting from bootloader and with activesync disabled.
Click to expand...
Click to collapse
HI!
Thank You for your answer. I made yours tip, but not was good.
First I to try smarty77 tip. I used RUU120_172125_Qtek_WWE_R11400_Shipping. Its function. After I’d like rom upgrade. This doesn’t was good (invalid vendor).
Second I to try clearing with mtty.exe.
The situation same, the phone doesn’t work.
Sorry my bad English.
Just seen your capture but it's not good.. you made a "basic" capture which shows nothing important, please repeat the process again, but this time read point 6:
In the upper part there are two tabs: basic and complete. Click on "Complete".
I cannot help unless I have a complete capture to see the problem.
pof said:
Just seen your capture but it's not good.. you made a "basic" capture which shows nothing important, please repeat the process again, but this time read point 6:
In the upper part there are two tabs: basic and complete. Click on "Complete".
I cannot help unless I have a complete capture to see the problem.
Click to expand...
Click to collapse
HI POF!
Thank you four your help.
It is a new captured files.
Please help me. You are a last chance, for my phones.
Lacika
@lacika:
When checking the seclevel (task 32 bootloader command) your phone replies:
Code:
CID: Wait interpreter timeout.
Level=FF
After that when checking the CID with 'info 2' your phone replies:
Code:
HTCS...?\0.?f..|HTCE
This should be something like T-MOB001 if you have a Vario II from UK, so the CID is screwed.
I can see from the output of 'info 3' that you're running bootloader 1.06.
Then you try to flash the 1.18.255.3 ROM from HTC, which has CID "QTEK_001", you won't be able to flash this image in your device with bootloader 1.06, even if the CID was not screwed you will always get an error (you need bootloader 1.04 to bypass CID checking, and you are in 1.06), the error you're getting from bootloader is:
Code:
CID not allow (255)
As you said you can use the PDA (WinCE boots) what I suggest is buying imei-check unlocker (you need activesync working too for running the imei-check unlocker), because it will downgrade your bootloader to 1.04 and patch your radio... probably it can fix your device, at least it will downgrade your bootloader to 1.04. If after running the unlocker your device doesn't work I suggest that you try to flash a radio ROM, you can find them here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms
Let me know how it goes
pof said:
As you said you can use the PDA (WinCE boots) what I suggest is buying imei-check unlocker (you need activesync working too for running the imei-check unlocker), because it will downgrade your bootloader to 1.04 and patch your radio... probably it can fix your device, at least it will downgrade your bootloader to 1.04.
Click to expand...
Click to collapse
Err... I forgot that your IMEI is also screewed, probably imei-check unlocker will not work on your Hermes even if you provide them the right IMEI, because it will not be able to read the IMEI from your phone (will get the wait interpreter timeout too...). anyway... it costs 20GBP, give it a try!
pof said:
@lacika:
As you said you can use the PDA (WinCE boots) what I suggest is buying imei-check unlocker (you need activesync working too for running the imei-check unlocker), because it will downgrade your bootloader to 1.04 and patch your radio... probably it can fix your device, at least it will downgrade your bootloader to 1.04. If after running the unlocker your device doesn't work I suggest that you try to flash a radio ROM, you can find them here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms
Let me know how it goes
Click to expand...
Click to collapse
Hi and thanks!
I’ve got one question. I use imei-check unlocker after I’ll got 1.04 bootloader?
Lacika
I tried that with my device before it got sent to service, I brought imei-check unlocker but as my imei was also corrupt it will not work, so I would not waste GDP 20 if you have corrupt imei.
They will not refund either becuase its your problem the imei is corrupt.
lacika said:
I use imei-check unlocker after I’ll got 1.04 bootloader?
Click to expand...
Click to collapse
No, imei-check unlocker will downgrade your bootloader, BUT as shark1 says, it will not work because your IMEI is corrupted and it will not be able to read it.
I guess the best would be to send the unit to the repair centre then...
pof said:
@lacika:
As you said you can use the PDA (WinCE boots) what I suggest is buying imei-check unlocker (you need activesync working too for running the imei-check unlocker), because it will downgrade your bootloader to 1.04 and patch your radio... probably it can fix your device, at least it will downgrade your bootloader to 1.04. If after running the unlocker your device doesn't work I suggest that you try to flash a radio ROM, you can find them here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms
Let me know how it goes
Click to expand...
Click to collapse
Hi!
I’ve got a new problem.
I used a M3100v3cUnlock.exe program. This doesen’t read my imei number.
I don’t know how can I flash my bootloader.
Lacika
pof said:
No, imei-check unlocker will downgrade your bootloader, BUT as shark1 says, it will not work because your IMEI is corrupted and it will not be able to read it.
I guess the best would be to send the unit to the repair centre then...
Click to expand...
Click to collapse
I had the same problem! Send it to orange assistance.
lacika said:
I used a M3100v3cUnlock.exe program. This doesen’t read my imei number. I don’t know how can I flash my bootloader.
Click to expand...
Click to collapse
You can't, and your imei is screwed, the unlocker can't check it... so you should better send the unit to the repair centre as suggested.
pof said:
You can't, and your imei is screwed, the unlocker can't check it... so you should better send the unit to the repair centre as suggested.
Click to expand...
Click to collapse
HI!
I’ve got a last question.
It will a new procedure, program, with I can flashing my bootloader.
Lacika
here is what I've done and what happened:
my ROM was HTC 1.18.255.3 07/22/06 with bootloader 1.04 then I ran "HERM_Unlock_v2a.exe" on the device but I didn't use "HTC_Hermes_Radio_for_SIMunlock_v1.16.00.69" to save time and i wanted a CID unlock only.
after "SUCCESS!" message from "HERM_Unlock_v2a.exe", I connected my device via USB to PC and started to upgrade to Cingular 1.31.502.1 08/30/06 with aku 2.6 and bootloader 1.06 but when I get the "ID ERROR",without disconnecting the USB, I switched back to ugrading to previous ROM HTC 1.18.255.3 and the Processe started with no problem untill 98%, then suddenly upgading interrupted a message came saying connection error or somting like that!
since then my device is stuck on windows mobile screen and I've tested solutions in the "Hermes_Upgrade Problems" page and tried using the "Hermes SD Card flashing" method, But It seems impossible to flash my phone agian.
Help me PLEASE,HELP
someone help me please!
POF can't you help me please
I think Pof is away until 3rd december, I have the similiar problems with my second hermes, if you have then use mtty to see if you have an corrupted cid using info 2.
Do you have the original rom to go back on if so that will fix your problem.
I've used mtty to send some commands to my device and it answers to some of them but It just stop responding when I type "info 2" or "info 3".
and i tried this in mtty:
"
USB>checkimage
IPL CRC checksum = 0x9FCC6BEB
SPL CRC checksum = 0x3BF03635
CE CRC checksum = 0xC0E1751A
ExtROM CRC checksum = Total Block= 1024
dwBlockIndex= 1024
Address Error1!!!
Get checksum ERROR!!!
0x0
Radio Image CRC checksum =
"
again It stop responding
also tried upgrading, no matter which ROM I try, it just can't connect to device.
and thanx for your relpy.
hi, since there is NO htc service center available around me I have to do something about it myself but my phone is still dead and I'm using a nokia 1101. PLEASE someone help me, pof are you back? can you help me?
I've tried all in this page:
"http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems"
and this one too:
"http://forum.xda-developers.com/showthread.php?t=280733"
and tested qtek 2020 rom but no use.
from what I've found out my device hang up and stop responding when it gets the "INFO 2" or "INFO 3" or "TASK 32" or perhaps any thing involving CID so no upgrading utility is able to connect to it, the only thing is to connect to it using "mtty.exe" which I've tried any command found here, but no use again.
and my SPL is 1.04
can anyone help me?
mht220 said:
I ran "HERM_Unlock_v2a.exe" on the device but I didn't use "HTC_Hermes_Radio_for_SIMunlock_v1.16.00.69" to save time and i wanted a CID unlock only.
Click to expand...
Click to collapse
Wrong, you also need a patched radio to CID unlock. Running only the exe file without the patched radio has no effect on the unit.
mht220 said:
from what I've found out my device hang up and stop responding when it gets the "INFO 2" or "INFO 3" or "TASK 32" or perhaps any thing involving CID so no upgrading utility is able to connect to it, the only thing is to connect to it using "mtty.exe" which I've tried any command found here, but no use again.
and my SPL is 1.04
Click to expand...
Click to collapse
Please attach usb monitor capture when trying to flash a ROM and a radio ROM. Otherwise can't help you.
here is exported files from usb-monitor:
and tanx for your reply
uuh... there must be something really wrong with it, no response to bootloader commands. If no sd card flashing is possible, I would suggest you to send it to service centre too.
pof said:
...I would suggest you to send it to service centre too.
Click to expand...
Click to collapse
It's a difficult option for me, as I should send it to a foreign country to service center,so are you sure there is no way like erasing somewhere using mtty?
pof said:
... no response to bootloader commands...
Click to expand...
Click to collapse
but it respond to some of them in mtty.exe e.g. "erase", "set" and some other.
pof said:
...If no sd card flashing is possible...
Click to expand...
Click to collapse
no it would stuck in "checking..." forever
tanx
HI,
I have same exactly problem on my spv m3100: since sept06 I've tried every kind of Unlock software,upgrade ROM and method found in xda..In mtty bootloader (spl 1.04) respond at every command but not "info 2","info 3" and "task 32".Sd card method works but if you try to upgrade other ROM,in your screen "loading..." and then "checking..." hangs on because the ROM upgrade must to match CID (I suppose..).I'll wait the next ROM Upgrade and ORANGE won't release it until gen07..
warrio said:
I'll wait the next ROM Upgrade and ORANGE won't release it until gen07.
Click to expand...
Click to collapse
it seems your problem is like mine if so, I don't think ANY normal upgrade can solve your prolem 'cause it can't connect to it.
so don't wait and send your device to service center, if you can.
I'm in your same conditions:there's no repair center here so I have to wait Orange who release a upgrade Rom (I hope asap..).
Hello everybody - can anyone help me at this moment. I am right now sitting with my Hermes connected through USB. I was flashing the standard ROM with RUU_HERMES_HTC_WWE_1[1].35.255.2_1.35.255.102_1.08.00.10_SHIP. Unfortunately it stopped at 5% some half an hour ago. I prefer to ask you before disconnecting it. Please help!!!!!!!!!
OK, having no answer I decided to disconnect it and look for an answer. Now I know that I have a 1000 USD brick and no possibility to put it back to work.
I now suspect that the upgrade did not work properly because my device had a CID lock. That is quite strange however, because I bought it on the open market without any commitment to any GSM operator.
I am now stuck on the tricolor bootloader screen with SPL 1,09.
Basing on the post: http://forum.xda-developers.com/showthread.php?t=285157 - especially on the lines:
"1.09
You can't downgrade to bootloader 1.04 by flashing a Shipped ROM. However imei-check.co.uk is able to downgrade the bootloader.
There was a solution posted on this forum, but it was stolen from imei-check and was removed. If you are not willing to pay you have to wait until another solution is developed.
The RadioROM can't be upgraded. You have to downgrade to bootloader 1.04 to unlock your device.", despite seeing info on the website, I paid to imei-check the 20 pounds.
So far I only lost money, time and nerves trying to downgrade or "repair" my hermes. Nothing works. If anybody has any suggestions please share on the forum or PM me.
BTW I started the whole process with SPL 1,04.
Sounds to me like a flaky USB port which is why it stopped at 5%. Try another port in the rear of your PC and re-flash. Be sure to follow the mantra:
Windows XP, screensaver, powersave disabled
No other programs running.
i had a similar problem probably with the flaky usb port as Sleuth255 mentioned. trying with a different pc is another option if you have one and that was what i did with success.
im not sure about the hermes.. but i know on the wizard as long as you could get to the bootloader screen (the RGB screen) that your device isnt bricked yet.. i would follow the other suggestions about usb ports and using different pc's, i bet you can make your $1k work for you again
Try:
Go into bootloader by pressing down both the POWER button and SIDE OK together and using the stylus at the same time to press the RESET button at the bottom.
Make sure you have disabled the USB connection in ActiveSync, before trying to connect to the bootloader:
File --> Connection settings --> uncheck "allow USB connections"
Connect your USB-Cable
Download mtty.exe. Start it and connect to USB
When you see "USB>" Type "info 2". You should get: "HTCS" + CID + (4-byte checksum) + "HTCE". Remeber what CID you have.
Look for a Shipped ROM that matches your CID
Download and flash it using a different USB-Port or PC than the last time
Afterwards you will be able to use the file that you got from imei-check. The imei-check downgrader/unlocker only works if you've got a working operating system on your device.
After typing "info 2" in mtty.exe I get the following line
HTCSF kEŘ(HTCEUSB>
Which of those is the CID? I cannot find any matching one in the Wiki.
corrupted CID by wrong flash.
OK, I have now the confirmation of the diagnosis - as I was suspecting.
Can I now have some help in the solution?
Some people succeded with the method described as "problem 5" here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
but some others don't succeed and have a brick. Try the steps on the wiki, if you are not able to fix it this way, send it to repair centre.
Following the steps from point 5 of the given website, I only get the following lines:
USB>password 0000000000000000
HTCSPass1.CMˆËHTCEUSB>
USB>set le 1
USB>erase a0040000 c80000
HTCST ÚČŇHTCEUSB>
USB>erase a0cc0000 c80000
HTCST ÚČŇHTCEUSB>
USB>erase a1940000 640000
HTCST ÚČŇHTCEUSB>
USB>set le 0
USB>
Unfortunatelly nothing changes.
I've the same problem. I was flashing the HTC 1.18.416.1 1.18.416.101 1.14.00.10 but the process has stopped to 89 % and now the phone is in bootloader mode spl- 1.06 and don't enter in windows mode !!! My cid is HTCSORANG001a#USB> I hope that i've not a brick !!!
mtadeuszak said:
Following the steps from point 5 of the given website, I only get the following lines:
[...]
Unfortunatelly nothing changes.
Click to expand...
Click to collapse
Your bootloader is 1.09 and you'll not be able to flash anything because the CID will not match. Send it to service centre.
deika95 said:
I've the same problem. I was flashing the HTC 1.18.416.1 1.18.416.101 1.14.00.10 but the process has stopped to 89 % and now the phone is in bootloader mode spl- 1.06 and don't enter in windows mode !!! My cid is HTCSORANG001a#USB> I hope that i've not a brick !!!
Click to expand...
Click to collapse
Your phone is not trashed, but there is no rom matching your CID yet. You should have cid unlocked it before flashing a rom with BL 1.06.
Try to boot OS again using "set 14 0" (see wiki, "problem 4"), if that doesn't fix it (chances are it will not), then wait until orange releases a rom upgrade with CID "ORANG001".
I've try the procedure "Problem 4" but after "write nand success" and sr it don't start. My cid is always ORANG001 with spl-1.06
pof said:
Your bootloader is 1.09 and you'll not be able to flash anything because the CID will not match. Send it to service centre.
Your phone is not trashed, but there is no rom matching your CID yet. You should have cid unlocked it before flashing a rom with BL 1.06.
Try to boot OS again using "set 14 0" (see wiki, "problem 4"), if that doesn't fix it (chances are it will not), then wait until orange releases a rom upgrade with CID "ORANG001".
Click to expand...
Click to collapse
Please Pof try to help me. Where can i find that rom ? Thanks
You can't find it at the moment. It's not released yet
sn00x said:
You can't find it at the moment. It's not released yet
Click to expand...
Click to collapse
But you think that it will be available ? Thanks
Yes it will surely be released I think. But nobody knows when. Perhaps tomorrow, perhaps next year.
It bet it will be listed here when it's available.
Ok I have searched the forums pretty hard the last couple of days, and I have not found anyone that has the same issue as mine. It's not too big of a deal as everything operates but it is an issue all the same. This is all of course after I have succesfully ran HARD SPL v7 and upgraded to Black 3.0.1. Basically I decided to use POF's SuperCid Unlocker 3a (yes I know if I had HARD SPL 7 then why go through the trouble of Unlocking my CID, let's call it a need to mess with things) and everything went succesful. Then after the fact I read that it is still good even if you have SuperCID to upgrade the SPL to 2.10 and have read some peoples signatures and it appears that they have succesfully done this. Here is my issue;
When I run the CustomRUU it autodetects my SPL no problems, HARD-SPL? is checked, everything seems to go fine until it gets to the boot loader, once it is there, the progress bar pops up, zings to 100% and then reboots, cool? no because it didn't actually upgrade anything everything is still the same. Ok, so I tried the format SD card and rename *.nbh file to HERMIMG.nbh and put only it on the card, when I go to bootloader it does a quick flash to the screen like it recognizes the image but then goes to boot loader and nothing changes (the flash is so quick I can't even read whatever message it may be showing). I have tried pretty much every flashing method I can come across. MTTY wont recognize that I even have a USB port so I have been unable to try that method. So two questions:
I have SuperCID, so should I continue to even bother to get to 2.10?
If so, is there anything else I can try? Or do I need to get MTTY to work and try that as that is really the only thing left?
Thanks for any and all help anyone can provide.
PuckX said:
Ok I have searched the forums pretty hard the last couple of days, and I have not found anyone that has the same issue as mine. It's not too big of a deal as everything operates but it is an issue all the same. This is all of course after I have succesfully ran HARD SPL v7 and upgraded to Black 3.0.1. Basically I decided to use POF's SuperCid Unlocker 3a (yes I know if I had HARD SPL 7 then why go through the trouble of Unlocking my CID, let's call it a need to mess with things) and everything went succesful. Then after the fact I read that it is still good even if you have SuperCID to upgrade the SPL to 2.10 and have read some peoples signatures and it appears that they have succesfully done this. Here is my issue;
When I run the CustomRUU it autodetects my SPL no problems, HARD-SPL? is checked, everything seems to go fine until it gets to the boot loader, once it is there, the progress bar pops up, zings to 100% and then reboots, cool? no because it didn't actually upgrade anything everything is still the same. Ok, so I tried the format SD card and rename *.nbh file to HERMIMG.nbh and put only it on the card, when I go to bootloader it does a quick flash to the screen like it recognizes the image but then goes to boot loader and nothing changes (the flash is so quick I can't even read whatever message it may be showing). I have tried pretty much every flashing method I can come across. MTTY wont recognize that I even have a USB port so I have been unable to try that method. So two questions:
I have SuperCID, so should I continue to even bother to get to 2.10?
If so, is there anything else I can try? Or do I need to get MTTY to work and try that as that is really the only thing left?
Thanks for any and all help anyone can provide.
Click to expand...
Click to collapse
Did you look on the bootloader screen to see if your SPL changed? To my knowledge the only place you can see it is in the bootloader screen (tri-color screen) And flashing Olipro's Hard SPL only takes a couple seconds so it sounds to me like it is working as designed.
Or are you trying to flash a different rom? If so then try deleting everything you have in the directory you are using and re-downloading. You might have over-written the file you want to flash with the HardSPL one. You shouldn't be using the hard spl wrapper to flash a rom in any case, i believe that is mentioned in bold at the top of the Hard SPL thread.
Ok nevermind I was able to get it to work and MTTY was the answer. This is the 2 steps I had to follow:
From the thread: http://forum.xda-developers.com/showthread.php?t=291723
sp3dev said:
Hi. I`ve finally found the way to connect mtty and run rom update utility in Vista. tested on rtm 6000.
First of all, connect your device when it`s in bootloader.
next, open Windows Mobile Device Center and in connection settings uncheck Allou USB Connections.
next, goto contol panel-administrative tools-services and start windows mobile device connectivity and windows mobile device 2003 connectivity
next, goto device manager and find your device and update the driver to the one from AS 4, i attached it, wceusbsh.inf.
then, kill wmdc.exe with any taskmanager
You are Ready. run ruu or connect MTTY. I guess that vista default driver uses another port, not WCEUSBSH001, that`s why we have to use the old driver.
Click to expand...
Click to collapse
Then Do This:
http://wiki.xda-developers.com/index.php?pagename=Hermes_BootloaderMFG
Flashing SPL-1.01 MFG instructions
Put hermes in bootloader mode (side ok + power button + softreset)
Connect Hermes to computer using USB cable.
Open mtty.exe, select "USB" from the dialog box, then hit Ok.
Hit enter twice and you'll see the "USB>" prompt.
Then type these commands: (note the use of 'lnb*s*')
USB>task 32
Level = 0
USB> lnbs SPL-1.01.nbs 50020000
USB> task 8
Device will reboot after this, with bootloader 1.01-MFG on it.
Once I was able to do all this I was succesfully at 1.01 at which point I ran the Custom RUU and upgrade to 2.10 without issue. Once again all right there in the forums, just had to be pieced together to find a solution.
Thank you all for all your dedication to these projects, you make owning a PDA more fun than I am sure was originally intended. I love messing with things.
I have also attached the necessary files from the original posts to perform this for anyone else facing this issue.
PuckX said:
Ok nevermind I was able to get it to work and MTTY was the answer.
Click to expand...
Click to collapse
Cool, glad you got it working
PLEASE HELP I HAVE BRICKED TYTN CAN NOT CHANGE BOOTLOADER CID LOCKED??HELP PLEASE WILL PAID WITH PAYPAL IF ANY MAN CAN HELP ME....
I wanna know whether any one is working to find a sulotion to unbrick the bricked devices HTC TYTN with "SPL 2.03, IPL 1.04, NO GSM, KITL Disabled"!!!!!???????Can not boot only bootloader WHEN PUT IN MTTY, Cid locked LEVEL=FFF
I try this :http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=59&Itemid=27
- NOT WORK always 100% then message : image corrupted !!!!!!! And not change bootloader....
Sd card not work format sd card fat32 and try all TYTN ROM!!!
hen i tried to rom upgrade using any ruu (ruuwraper,.....) it only shows 1% and my device reboots and ....
it looks like LOSE super CID and my boootloader change and now ipl 1.04 and spl 2.03 NOW WHEN GO IN BOOTLOADER AND MTTY command:
Cmd>task 32
CID: Wait interpreter timeout
Level = FF
Cmd>info 2
HTCSF kEØ(HTCE
Cmd>
Cmd>info 7
HTC Integrated Re-Flash Utility, Common Base Version : 1.51d
Device Name: HERM100, Bootloader Version : 2.03
Built at: Jun 16 2007 01:57:22
Copyright (c) 1998-2006 High Tech Computer Corporation
CPU ID=0x41129200
Main CPLD version=0x5
Upper CPLD version=0x4
Main Board version=0x5
----------------------------my bootloader is changed...HELP PLEASE
any suggestions????
any solution to fix this and bootloader AND ALL PLEASE.....
I have tested everything on my bricked hermes but didn't work! READ ALL IN XDA DEVELOPER BAT NOT FIND SOLUTION-SD CARD NOT WORK????
IS ANY SOLUTION I AFTER I READ ALL IS ANY CHENCE HELP ME I WILL PAID WITH PAYPAL IF YOU CAN GIVE ME SOLUTION FOR MY HTC TYTN PLEASE
THANKS FOR ALL AND I HOPE THAT POF WILL RESPOND ME ITS VERY IMORTANT TO ME.
SORY FOR MY BAD ENGLISH....
If you get no replies here, try post it on the link in my signature. I've posted things there for work and found some decent bids.
Olipro Hard Spl 7 NOT WORK ...
Olipro Hard Spl 7 OR ANY HARD SPL NOT WORK WHEN TRY TO UPDATE MY TYTN I SEE 100% IN MY PHONE THEN MESSAGE IMAGE CORRUPTED. IS ANY CAN HELP ME.???????????
Pof did not show up here in last two months. Wondering what has happened to him.
Exactly same issue here.
it seems that there is no sulotion for it for now
I took my device to a service center (not imate servicecenter, because there is no imate certified service center here in my country) and they told me that they should replace my imate's motherboard with a new one and that will cost me about 420$. f***cking service center. i have a bricked and useless jasjam now!
Guys I took a look at the Hermes Unbricking page and I think that you fall to the category not even Pof can repair. Your bootloader is not directly mentioned but the circumstances of your case are the same as in:
1.06, 1.09, 1.11 or 2.02, Any HTC Boot, Will not boot to windows, NO GSM, NO KITL - Bricked while flashing radio, bootloader doesn’t allow to flash unsigned code. BRICK - Send it to repair centre, warranty... Basically you are in the very same situation - only your bootloader version is different - but it is an official bootloader that does not allow unsigned code flashing.
try unpacking the official upgrade from your service provider with ruuwrapper. I had this problem and it worked for me.
ruuwrapper not work!!!
i try to rom upgrade using ruuwrapper
(try offical htc rom and many other more then 20 htc roms) it only shows 1% and my device reboots and ....
it looks like LOSE CID and my boootloader change and now ipl 1.04 and spl 2.03 NOW WHEN GO IN BOOTLOADER AND MTTY command:
Cmd>task 32
CID: Wait interpreter timeout
Level = FF
------------------bat before lose cid i have super cid!!!
mbsshop1302gsm said:
i try to rom upgrade using ruuwrapper
(try offical htc rom and many other more then 20 htc roms) it only shows 1% and my device reboots and ....
it looks like LOSE CID and my boootloader change and now ipl 1.04 and spl 2.03 NOW WHEN GO IN BOOTLOADER AND MTTY command:
Cmd>task 32
CID: Wait interpreter timeout
Level = FF
------------------bat before lose cid i have super cid!!!
Click to expand...
Click to collapse
Dude!, I have exactly in the same situation as you.
I think the only way we can fix our devices is to find the bootloader password and then flash the radio with MTTY. The most important problem here is that we cannot flash our devices using ROMUpgradeUt.exe because it cannot connect to our devices, so we cannot find the bootloader password using the pof & esteve method "HTC Hermes BootLoader PASSWORD".
We can only flash our devies using the ROMUpdateUtility.exe.
I tried to do the above method on ROMUpdateUtility.exe and RUUResource.dll instead but there is no password field in RUUResource.dll . Maybe someone like pof should work with this dll to see how does it works!
Solution That Sspl-herm.EXE Can Start With Windows Command?? AS I SAY IN LAST POST
koorosh_bsboys said:
Dude!, I have exactly in the same situation as you.
I think the only way we can fix our devices is to find the bootloader password and then flash the radio with MTTY. The most important problem here is that we cannot flash our devices using ROMUpgradeUt.exe because it cannot connect to our devices, so we cannot find the bootloader password using the pof & esteve method "HTC Hermes BootLoader PASSWORD".
We can only flash our devies using the ROMUpdateUtility.exe.
I tried to do the above method on ROMUpdateUtility.exe and RUUResource.dll instead but there is no password field in RUUResource.dll . Maybe someone like pof should work with this dll to see how does it works!
Click to expand...
Click to collapse
YES MATE I THINK BAT WHERE IS POF!!! POF WHERE ARE YOU????
OR
Is Any Solution That Sspl-herm.EXE Can Start With Windows Command?? I MEAN I CAN ONLY PUT PUT MY BRICKED TYTN IN BOOTLOADER BAT CAN NOT START SSPL-HERM.EXE BECAUSE NOT WANT TO LOAD ....IS ANY CHANCE TU START Sspl-herm.EXE WITH WINDOWS COMMAND TO CHANGE BOOTLOADER TYTN IN SSPL HERM THEN WE CAN FLASH BRICKED DEVICE!!!??
SO I HOPE THAT SOMEBODY CAN CREATE PATCH FOR THIS THAT SSPL-HERM.EXE CAN START IN WINDOWS THEN CHENGE BOOTLOADER IN HERMES WHEN HERMES CONNECTED WITH USB AND ONLY CAN LOAD BOOTLOADER.....
I MEAN
THAT Sspl-herm.EXE CAN RUN IN WINDOWS AND CHENGE AUTOMATICALY BOOTLOADER IN PHONE WHEN PHONE ONLY CAN RUN BOOTLOADER AND CAN NOT RUN OS...I HOPE THAT YOU UNDERSTAND WHAT I MEAN SORY FOR MY BAD ENGLISH.
mbsshop1302gsm said:
YES MATE I THINK BAT WHERE IS POF!!! POF WHERE ARE YOU????
OR
Is Any Solution That Sspl-herm.EXE Can Start With Windows Command?? I MEAN I CAN ONLY PUT PUT MY BRICKED TYTN IN BOOTLOADER BAT CAN NOT START SSPL-HERM.EXE BECAUSE NOT WANT TO LOAD ....IS ANY CHANCE TU START Sspl-herm.EXE WITH WINDOWS COMMAND TO CHANGE BOOTLOADER TYTN IN SSPL HERM THEN WE CAN FLASH BRICKED DEVICE!!!??
SO I HOPE THAT SOMEBODY CAN CREATE PATCH FOR THIS THAT SSPL-HERM.EXE CAN START IN WINDOWS THEN CHENGE BOOTLOADER IN HERMES WHEN HERMES CONNECTED WITH USB AND ONLY CAN LOAD BOOTLOADER.....
I MEAN
THAT Sspl-herm.EXE CAN RUN IN WINDOWS AND CHENGE AUTOMATICALY BOOTLOADER IN PHONE WHEN PHONE ONLY CAN RUN BOOTLOADER AND CAN NOT RUN OS...I HOPE THAT YOU UNDERSTAND WHAT I MEAN SORY FOR MY BAD ENGLISH.
Click to expand...
Click to collapse
I know what you mean
But unfortunately sspl-herm.exe is a WinCE application and cannot run on x86 or x32 windows.
sspl-herm.exe is a WinCE ?
yes i know this bat i try to work to resolve many bricked device so is any change to create somebody pach that work in windows xp ???I mean when i click in this icon sspl-herm.exe that automaticaly change bootloader in bricked tytn when i have only bootloader ??/