I tried this way - http://en.pdamobiz.com/en/forum/forum_posts.asp?TID=151, but when i press any key in mtty i get the error "Usb Transfer Fail"
Is it possible to backup ROM on my Orsio?
Try it again, maybe some problems with connection?
I tried many times at several PCs and diferrent cables - no way.
There should be a trick...
Related
hey Folks,
it seems i bricked my device while flashing the new PRO ROM.
After 91% i got an breakup and the update tool prompted error 262. Since then I stock in bootloader mode - no connection to windows xp can be established.
I have done the following things;
- tried tools like titan_exitbl oder mtty (can't tick the usb option)
- tried to flash an original rom via sd card (128mb) - it states searching sd card and then goes into bootloader
Again, i neither i can leave the bootloader nor establish an usb connection (even if the device shows on the left bottom usb after i 've connected it)
very thankful for any advises.
IRM
4irm said:
hey Folks,
it seems i bricked my device while flashing the new PRO ROM.
After 91% i got an breakup and the update tool prompted error 262. Since then I stock in bootloader mode - no connection to windows xp can be established.
I have done the following things;
- tried tools like titan_exitbl oder mtty (can't tick the usb option)
- tried to flash an original rom via sd card (128mb) - it states searching sd card and then goes into bootloader
Again, i neither i can leave the bootloader nor establish an usb connection (even if the device shows on the left bottom usb after i 've connected it)
very thankful for any advises.
IRM
Click to expand...
Click to collapse
is it version 3.06 of bootloader? if yes, thats known issue with this version of BL
that can be happen very rarely and if you are flashing official ROMs too, so thats not my bad
i can advice two things only:
1. try to use another microSD cards (from different manufacturers)
2. return it to HTC/Qtek
Sorry
its 3.06...
thx,will send it back - of course its not your fault...
keep on your good work anyway!
cheers
IRM
Hi,
I have had my 8125 for about 2 1/2 years now, love it!. Just the other day, it started locking up and giving me the white screen of death.
I tried to flash it with a rom, and it got to 99% and then lost connection. Tried to do the recovery, but that failed too.
I have found alot of good information from the smart and wonderful people on this forum and tried a bunch of stuff.. but I am now stuck.
Now, I can always boot into the bootloader, and it says USB over the left softkey, but no apps can connect to the phone.
I tried to use other RUU roms, HardSPL, SoftSPL, etc...I tried to unlock my CID using the thread in this forum, but SoftSPL couldnt connect to the phone via USB.
All apps error with "error unable to connect to device."
I have read the forum about having a bad mimi-USB port, but I dont think thats my case.
Please help! I am pretty close
Dell D620 CoreDuo 1.8Ghz; WinXP SP2
ActiveSync 4.5
IPL 2.25.0001
SPL 2.25.0001
end123 said:
Hi,
I have had my 8125 for about 2 1/2 years now, love it!. Just the other day, it started locking up and giving me the white screen of death.
I tried to flash it with a rom, and it got to 99% and then lost connection. Tried to do the recovery, but that failed too.
I have found alot of good information from the smart and wonderful people on this forum and tried a bunch of stuff.. but I am now stuck.
Now, I can always boot into the bootloader, and it says USB over the left softkey, but no apps can connect to the phone.
I tried to use other RUU roms, HardSPL, SoftSPL, etc...I tried to unlock my CID using the thread in this forum, but SoftSPL couldnt connect to the phone via USB.
All apps error with "error unable to connect to device."
I have read the forum about having a bad mimi-USB port, but I dont think thats my case.
Please help! I am pretty close
Dell D620 CoreDuo 1.8Ghz; WinXP SP2
ActiveSync 4.5
IPL 2.25.0001
SPL 2.25.0001
Click to expand...
Click to collapse
Ok,first,no other custom build rom will flash on it,except official stock rom of the carrieror,however, you can try wizard_love rom,as it has patched IPL/SPL (Bootloaders),so don't try to flash any other custom build,as its a G4,custom rom can only be flashed through SoftSPL or HardSPL.
Download official carrier's stock rom and wizard_love rom.
Secondly,
1.Disable activesync or rather uninstal it altogether,as its not needed during flashing a rom.
2.End process 'wcescomm.exe' in the 'windows Task Manager.
3.Clear and delete the 'Temp Folder' files
4.Run 'Disk Cleaner'
5.Disable all Anti Virus and Firewall.
6.Try to stop/disable all running programs in the background via 'Task Manager'
7. Get the battery fully charged,as many comm errors are due to weak or discharged battery.
After doing all this,get the phone in Bootloaders before connecting with pc via usb cable,there shudn't be any usb at the bottom of the Bootloaders,now connect with pc and check if usb appears at the bottom,if its there than,its establishing connection,go ahead and run official stock or wizard_love rom.Don't use the pc or play games or check emails,don't even do any word,excell or any office application.Check if any application/program interferes with the flash,either disable or remove that program.
Does the battery get charged through usb cable ? verify it.
If after getting the phone into bootloaders and connecting through usb cable,small usb doesn't appear,it means there's a connectivity problem,replace the usb cable and verify it again.Even try with another pc with winXP or change the usb input port of the pc ,put the usb cable in some other usb port on the pc.
Apart from all these,I don't find any reason for not getting the flash completed
Hi,
Thanks for the help.. I tried the wizzard_love rom, and then went to the NBD_v8.3 /w TouchFlo rom and thats awesome!
my biggest issue was not able to connect to the device although it looked like it should have.
on another thread someone said to leave the battery out for 5 mins. I did that and all of a sudden it started to connect consistantly.
After that I did the HardSPL and started flashing and all is well..
Thanks for your help!!!!
Hello to everyone.
I'm having a problem with my hero. I've just updated OTA with the original 2.1 OS from 2.73.405.5 to 3.32.405.1, and I lost the USB conectivity. There is no notification coming up when I plug the USB cable. I've tried different OS and cables and nothing seems to work. The phones can be charged through USB and the PC recognize it when I turn it on holding the volume down button and it says "Fastboot USB". Does anyone knows how to fix it or go back to the previous version, given that I don't have a propper USB connectivity?
By the way, I've contacted HTC support and they told me that I had to send the phone to the repair pipeline. I bought it through ebay, and I live in Chile, so that is not a real option to me.
same problem with me ! i hav no idea what the problem is happend when i flashed a 2.1 rom aswell!!
Can you get adb working? There are guides in various places.
If adb works, you can be sure it's not the whole usb playing up.
tried flashing 3 roms, modaco, radug and now kimera... none working.
can connect in fastboot, it shows up in device manager as android 1.0
ive tried 3 different usb cables and 4 differet pcs, still there is no response on my phone !!!
using villian rom 10.0 rite now.
okay it boots up into fastboot and fastboot usb shows up on the screen in red,
BUT when i use the "adb devices" command in adb it doesnt show the device,
it is showing as android 1.0 in devices and printers (windows 7)
Try deleting all the drivers using usbdeview (google it) and let windows re-install them when you boot into the custom rom. Have you tried turning on USB-MS in AmonRA recovery?
Another thing would be to try a non-2.1 custom rom and see whether that makes a difference (would be very surprised).
I think it is not a windows driver problem, because I've tried several USB cables and PCs, even a MAC, and nothing seems to work. I've tried to go back to the original 1.5 using the HEROIMG.zip method, but wont let me and says I have a newer version so it cant go back.
I think the only resource left for me is to send it back for repair... to bad.
ffelis said:
I think it is not a windows driver problem, because I've tried several USB cables and PCs, even a MAC, and nothing seems to work. I've tried to go back to the original 1.5 using the HEROIMG.zip method, but wont let me and says I have a newer version so it cant go back.
I think the only resource left for me is to send it back for repair... to bad.
Click to expand...
Click to collapse
I would hold off for now from sending it back.
If fastboot shows it up, then there's still hope. That means the hardware is fine. I remember spending many hours helping someone with this issue over at http://hero.modaco.com (look up my posts as username pulser, and it was early 2010 IIRC).
I can't remember how it got resolved. But if you can use a goldcard, you can try and roll it back to 1.5 using HEROIMG.zip. Without goldcard, it won't work
ffelis said:
I think it is not a windows driver problem, because I've tried several USB cables and PCs, even a MAC, and nothing seems to work. I've tried to go back to the original 1.5 using the HEROIMG.zip method, but wont let me and says I have a newer version so it cant go back.
I think the only resource left for me is to send it back for repair... to bad.
Click to expand...
Click to collapse
I have the same problem. you are able to solve?
I installed the original ROM 1.5, but are not able to restore the original recovery
I have the same issue Tried on different comps and on both XP and 7...
Btw what do you mean with the goldcard? I still got my original nand from back in august 2009..
bump, anybody?..
Try a ROM reset,
Menu > Settings > Privacy > Factory data reset.
This will erase all settings on the phone to go back to default settings so please make sure all your data is backed up. (Numbers et al)
I have a rooted stock ICS SGS2. Since a couple of weeks my USB connection on my laptop isn't working anymore. When I connect the SGS2 to USB, nothing happens on the phone and nothing happens on the laptop.
No "unknown device", no "USB connection" beep, no USB connection on the phone.
I tried a differtent cable, didnt work. I tried on another PC, didnt work.
I change developer USB-settings (USB error check) but didnt work.
I searched a lot, but couldn't find any solution. Can anyone please help me?
P.S. Running on Windows 7 64x Professional
edwindejong said:
I have a rooted stock ICS SGS2. Since a couple of weeks my USB connection on my laptop isn't working anymore. When I connect the SGS2 to USB, nothing happens on the phone and nothing happens on the laptop.
No "unknown device", no "USB connection" beep, no USB connection on the phone.
I tried a differtent cable, didnt work. I tried on another PC, didnt work.
I change developer USB-settings (USB error check) but didnt work.
I searched a lot, but couldn't find any solution. Can anyone please help me?
P.S. Running on Windows 7 64x Professional
Click to expand...
Click to collapse
does your phone charge when conneted to the computer, you do not need drivers for that. If it does not try cleaning the usb port on your phone, there maybe dust or something stopping the cable from making ful contact.
Hi,
I had a similar problem ,
1-first try to check in parmater section -> stockage if usb debugging is on
2-Second try to reinstall kies for drivers
3-> change cable or clean your usb port with a toothbruch (slightely hhhh)
4-> if nothing of these solutions works and you get an unknow device also with odin that means youre usb port is broken, it simple to change and dont cost a lot (170 MAD for me ).
There are other threads that spoke about the same problem.Hope it works
My phone charges when connected. I also tried re-installing Kies and cleaned the phone port. Nothing helped
As mentioned before, i tried lots of USB ports, also other PC's and other cables. Still not working.
Any clue?
If you've tried 'everything', then it's a hardware issue. Unroot it, reset the flash counter, send it in for warranty service.
Hello! I know, I know. There are a lot of different threads according to this problem but I read almost everything and still cannot fix my problem.
A few weeks ago when I tried to charge my phone the message: Your cable is not compatible with your device. Please use the orginal HTC-cable or your phone get damaged. appeared.
until that moment I thought it doesnt matter if I use a htc cable or a cable from another brand. I mean they changed all the ports to a micro-usb-port. Just to give you the opportunity to use every cable.
Well, after that I tried to connect my phone with my computer and the HTC Car app appeared and bluetooth got switched on. WHY?
I did a factory reset and flashed my rom again. Now I can connect my HTC One with my computer and on the screen of my computer appears the message:
"Device not recognized "Windows has stopped this device because it has reported problems. (Code 43)"
(and its unable to mount otg-usb in recovery)
I tried different cables. I tried to (un)install and update the HTC drivers. I tried different computer. I tried turning usb debugging off and on! I tried to clean the USB-pins! nothing works! :crying:
(Unfortunately I have no old backup with my new TWRP v2.6.)
I just have been abroad for 6 months and dont wanna loose all my photos and videos. Any ideas?
I think its a software issue on my phones. Maybe something with my partitions. But I dunno what I can wipe without deleting all my photos and video.
THANKS
seven09 said:
Hello! I know, I know. There are a lot of different threads according to this problem but I read almost everything and still cannot fix my problem.
A few weeks ago when I tried to charge my phone the message: Your cable is not compatible with your device. Please use the orginal HTC-cable or your phone get damaged. appeared.
until that moment I thought it doesnt matter if I use a htc cable or a cable from another brand. I mean they changed all the ports to a micro-usb-port. Just to give you the opportunity to use every cable.
Well, after that I tried to connect my phone with my computer and the HTC Car app appeared and bluetooth got switched on. WHY?
I did a factory reset and flashed my rom again. Now I can connect my HTC One with my computer and on the screen of my computer appears the message:
"Device not recognized "Windows has stopped this device because it has reported problems. (Code 43)"
(and its unable to mount otg-usb in recovery)
I tried different cables. I tried to (un)install and update the HTC drivers. I tried different computer. I tried turning usb debugging off and on! I tried to clean the USB-pins! nothing works! :crying:
(Unfortunately I have no old backup with my new TWRP v2.6.)
I just have been abroad for 6 months and dont wanna loose all my photos and videos. Any ideas?
I think its a software issue on my phones. Maybe something with my partitions. But I dunno what I can wipe without deleting all my photos and video.
THANKS
Click to expand...
Click to collapse
use an app like airdroid to copy all your stuff to your pc via wifi
also dropbox can hold all your photo's
then try and RUU back to stock