I am posting this outside of the bricked thread in despiration. I posted here http://forum.xda-developers.com/showpost.php?p=1250132&postcount=1164 for intial help.
Quick recap...
Had no GSM on boot...device info showed no radio or protocol versions.
Tried HTC_Hermes_SIM_CID_Unlock_v3a first, which might not have been the best choice. Load something (SPL i guess) then it stopped and tried recovery serval times.
Currently stuck in bootloader screen (tri-color) with this displaying:
HERM100
IPL 1.01
HERM100
SPL 1.40Olipro
Before flashing SPL was 1.11. I was instructed by digger_de to reload with new radio and select SPL 1.40 when asked... tried going to hard SPLv7 using latest CustomRRU...I selected FORCE SSPL (as per the guide) in the menu and tried to upload. Sits on "verify info on the hermes" screen then error 260 appears.
So I tried just to go to the new radio 1.41... I select SPL 1.40 from the menu..click update...get a progress screen that sits at 0% for a min or so...then error 262 displays. What do I do next?
Do I need to try KITLS or whatever, do I even have it? or do I need to use mtty and if so what commands?
I have read through the wiki and several threads, but I have not found something just like my situation.
I appreciate anyone that can point me the right direction.
Thanks,
Michael
reading more...
OK...did some more reading...ran mtty and some commands... seems radio is no there. How do I get it loaded?
Cmd>checkimage
IPL CRC checksum = 0x24C42773
SPL CRC checksum = 0x921BC30
CE CRC checksum = 0x4E705577
ExtROM CRC checksum = 0x1E9CA80
Radio Image CRC checksum = Checksum: Wait interpreter timeout
0x0
Cmd>`
Command error !!!
Cmd>
Cmd>
Cmd>info 8
Block 0x0(0) is Reversed block
Block 0x1(1) is Reversed block
Block 0x2(2) is Reversed block
Block 0x3(3) is Reversed block
Block 0x4(4) is Reversed block
Block 0x5(5) is Reversed block
Block 0x6(6) is Reversed block
Block 0x7(7) is Reversed block
Block 0x8(8) is Reversed block
Block 0x9(9) is Reversed block
Block 0xA(10) is Reversed block
Block 0xB(11) is Reversed block
Block 0xC(12) is Reversed block
Block 0x3FB(1019) is Reversed block
Partition[0], type=0x20, start=0x2, total=0x18FE
Partition[1], type=0x23, start=0x1900, total=0x1700
Partition[2], type=0x25, start=0x3000, total=0x19E00
Partition[3], type=0x4, start=0x1CE00, total=0x1DA00
CE Total Length(with sector info) = 0x3AA7000
CE CheckSum Length(without sector info) = 0x39C0000
Cmd>info 7
HTC Integrated Re-Flash Utility, Common Base Version : 1.60d
Device Name: HERM100, Bootloader Version : 1.40.Olipro
Built at: Mar 30 2007 15:10:47
Copyright (c) 1998-2007 Modified By Olipro - Hard-SPL
CPU ID=0x41129200
Main CPLD version=0x5
Upper CPLD version=0x4
Main Board version=0x6
Cmd>info 6
HTCST ÚÈÒHTCE
Hope you guys can help...I've got a long borring plane ride tomorrow..would love to play with the Herm on the plane.
Thanks!!
Michael
also...
Task 32 returns 0 ... so that means I am SuperCID right?
I am learning...slowly but surely.
MM
zerocool00 said:
I am posting this outside of the bricked thread in despiration. I posted here http://forum.xda-developers.com/showpost.php?p=1250132&postcount=1164 for intial help.
Quick recap...
Had no GSM on boot...device info showed no radio or protocol versions.
Tried HTC_Hermes_SIM_CID_Unlock_v3a first, which might not have been the best choice. Load something (SPL i guess) then it stopped and tried recovery serval times.
Currently stuck in bootloader screen (tri-color) with this displaying:
HERM100
IPL 1.01
HERM100
SPL 1.40Olipro
Before flashing SPL was 1.11. I was instructed by digger_de to reload with new radio and select SPL 1.40 when asked... tried going to hard SPLv7 using latest CustomRRU...I selected FORCE SSPL (as per the guide) in the menu and tried to upload. Sits on "verify info on the hermes" screen then error 260 appears.
So I tried just to go to the new radio 1.41... I select SPL 1.40 from the menu..click update...get a progress screen that sits at 0% for a min or so...then error 262 displays. What do I do next?
Do I need to try KITLS or whatever, do I even have it? or do I need to use mtty and if so what commands?
I have read through the wiki and several threads, but I have not found something just like my situation.
I appreciate anyone that can point me the right direction.
Thanks,
Michael
Click to expand...
Click to collapse
Quick question, the latest radios have CustomRUU 4.3 in them (i know because i repackaged them).....check the wiki. When you select your SPL version do you tick "Is it HardSPL?" ??
I think your problem can solved easily, as you have Olipro's hard SPL already in place, this allows you to flash any ROM. With the phone on the boot loader screen (the coloured bars), connect it to the PC and then run one of the radio upgrades from http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms - I currently use 1.40.30.00. If asked, select 'Hard SPL'.
If that doesn't work (i.e. you can't flash), you can try extracting the .nbh file from the radio upgrade, copy it onto a blank SD card, rename it to HERMIMG.NBH and reset the phone with the card inserted - see http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing for more information.
If you have any further problems I would strongly recommend that you spend some time reading the wiki - the answers to your questions are more than likely there.
I am having exactly the same problem as the op. When running Mtty get the same results just different checksums. (I have IPL-1.04)
When I flash just a radio rom it freezes. Does not matter if I do it via SD card or via PC.
Starting to get a bit frustrated with this and starting to get a bit too technical for me haha.
If anyone has any other ideas please let me know.
Cheers
mrvanx said:
Quick question, the latest radios have CustomRUU 4.3 in them (i know because i repackaged them).....check the wiki. When you select your SPL version do you tick "Is it HardSPL?" ??
Click to expand...
Click to collapse
Yessir...I did try that way. No go. Just sits on 0% for a min then phone restarts and PC (WinXP SP2 with .net 2) pops error 262 or whichever saying connection error.
forza said:
I think your problem can solved easily, as you have Olipro's hard SPL already in place, this allows you to flash any ROM. With the phone on the boot loader screen (the coloured bars), connect it to the PC and then run one of the radio upgrades from http://wiki.xda-developers.com/index...actedRadioRoms - I currently use 1.40.30.00. If asked, select 'Hard SPL'.
If that doesn't work (i.e. you can't flash), you can try extracting the .nbh file from the radio upgrade, copy it onto a blank SD card, rename it to HERMIMG.NBH and reset the phone with the card inserted - see http://wiki.xda-developers.com/index...SDCardFlashing for more information.
If you have any further problems I would strongly recommend that you spend some time reading the wiki - the answers to your questions are more than likely there.
Click to expand...
Click to collapse
I hope it is that easy. I appreciate your comments. Currently I do not own a SD card, but as soon as the plane lands this evening, I'll have one if you think that is the way. As for reading, I have read so much here over the past few weeks, it is crazy. That is part of the problem, there is tons of info here and on the wiki, some seems outdated, and as a new user, I wanted current instructions just to make sure I did everything correct.
Thanks,
Michael
@zerocool00: I answered you here:
http://forum.xda-developers.com/showthread.php?t=286755&p=1255936
We don't want the forum flooded with dead devices thread.... all the knowledge about dead devices is on the thread above. Please take your time to read and don't post desperately.
Closing this one.
Related
Hi everybody,
A friend of mine (who claims his English is not good enough to write here in forum) crashed his Hermes (T-Mobile Vario II, preproduction version). He tried to upgrade its ROM (from T-Mobile 1.4.110.1 to HERMIMG_Dopod_1.23.707.1_SHIP.nbh ) with a help of the following link: ftp://xda:[email protected]/Uploads/Hermes/CHT9000_ENG.exe
He followed the instructions:
Please note the existing ROM is English ROM from Dopod for the SE Asia market. I tried this ROM with my Chinese version of Dopod CHT9000 (Traditional Chinese version from Taiwan). If you try to flash it directly you will get a vendor error. Try the following steps:
1. Extract CHT9000_ENG.exe by right click (I use Winrar)
2. Make sure you are connected through ActiveSync.
3. Open ROMUpgradeUT.exe
4. Go through all steps. Eventually you will see your device reset and go into a ROM Flash screen at 0%. You should get an error from the Flash software stating wrong Vendor ID code.
5. Don’t disconnect the device or reset it. Close the Flash software.
6. Click on ROMUpgradeUT.exe again and go through all steps. This time it should start flashing the ROM.
7. That’s it.
Till the step 6 was everything OK. However after re-starting of ROMUpgradeUT.exe everything started again from the beginning. He got the error 262 saying:
ERROR [262"> : UPDATE ERROR
This error occurs during the CE ROM code upgrade process.
Solution: If this happens, you can just soft-reset the device and run RUU again. The update process will then continue.
Note: At this stage, the Wince is destroyed; instead, it is in upgrade mode.
After trying hard reset he lands in so called tri-color mode, he can see “herm100 IPL-0.16 a herm100 mfg spl-0.95”. That’s it. No hard reset possible. No other upgade (downgrade) possible.
My guess is he has to do something like here: http://www.spv-developers.com/forum/archive/index.php?t-455.html
Am I right?
We thought about upgrading to ftp://xda:[email protected]/Up...d_ROMs/HTC_TyTN_1.18.255.3_WWE_Dumped_ROM.zip
I found the instructions how to create these raw files, http://wiki.xda-developers.com/index.php?pagename=Hermes_HowtoDumpRom but I have no idea, how to use the created ones!!!
Could you explain it to me shortly???
Thanks a lot!
Hans Jansen
Hard reset will not help.
Go into Bootloader:
Bootloader mode: Hold side OK and POWER buttons together and reset with stylus.(from Wiki!)
Click to expand...
Click to collapse
If the Tytn is in bootloader mode, you can retry the flashing with the same or another update.
Good luck!
Bernhard
is there any difference?
Hi Bernhard,
Thanks a lot for your reply! However I am not sure if it helps. My friend says that "tri-color" and "bootloader" modes are one and the same mode.
He actually is able to start the flashing process again but is stops working by 0%... If he tries to repeat it - it is the same.
How is the situation with the raw files which I described in my first message?
Cheers
Hans
Re: is there any difference?
Hans Jansen said:
How is the situation with the raw files which I described in my first message?
Click to expand...
Click to collapse
I am investigating on this, but havent found a reliable method to restore "raw" rom images into Hermes yet. I'll put it in the wiki if I find something, any help is appreciated too
@Hans Jansen:
Are you able to find anohter HERM100 preproduction version (300Mhz) where you can extract the rom using the method descibed on the wiki?
When you are in the bootloader, you should be able to run RUU and flash the rom, but I guess the preproduction version has something different that is incompatible with the shipped or extracted roms from production versions, so the way to revive your firend's hermes should be by flashing another preproduction rom on it.
Follow this thread if you are interested in the process of making a valid .nbh file, but we don't know how to do it yet, you'll have to wait until we find the right way for hermes:
http://forum.xda-developers.com/viewtopic.php?t=58656
are you sayin that the only reason for this happening is because his unit is a preproduction unit?
vapor said:
are you sayin that the only reason for this happening is because his unit is a preproduction unit?
Click to expand...
Click to collapse
I don't know it for sure, but I've heared of two people who are stuck in bootloader after upgrade and both have preproduction models, so I guess it's a common problem on these units.
Hans Jansen:
Have u tried to connect through USB in bootloader mode using mtty?
1) Disable ActiveSync: connections -- settings -- uncheck "Allow USB Connections"
2) Open mtty.exe and select "USB" from the dialog box, then hit OK.
3) On the white screen hit enter and you should see a prompt like this:
USB>
Let me know if that works, probably we can do a full rom backup to microSD and you can load the rom from it.
I just got pre-production Hermes back to a OS using SET 14 0
So far many of you have been right on with suggestions regarding the pre-production units stuck in the boot loader are just that--- the 300mhz cpu, pre=prod Hermes 100 units. I was FINALLY able to use MTTY 1.42 I got from the buzzdev.net/downloads site. I used it by removing my battery, putting it back in, and powering on the unit which allowed the USB port to be opened again. I had to wait a minute or two for activesync to try to connect and say it couldn't recognize the device, then cancelled out of that and MTTY was able to see the USB port as an option. I connected, hit ENTER to get USB> prompt. Then typed SET 14 0 and then soft-reset the PPC and WALA!!! Original OS ROM 1.5 and radio version 0.92 back and OS functional. Not fully functional as it errors trying to load some MSN .cpl files, but I say no to opening them and I have a functioning phone! I've tried to reflash the device NUMEROUS times with the CHT9000 and other ROMs posted here, but they still return me to the stuck at boot loader and won't flash. Each time, I removed the battery, waited, used MTTY to set 14 0, and soft reset and back to a functioning OS. I guess I may have to wait for other roms to try. But at least the unit isn't a BRICK anymore! Even if the ROM sucks, just gotta be patient. I even tried using NoID RUU's and MA ruu. Neither worked.
Re: I just got pre-production Hermes back to a OS using SET
glad you have revived it
HTC makes things easy for us
I'll update the wiki, as this could be useful to someone else
EDIT:
http://wiki.xda-developers.com/index.php?pagename=Hermes_PreproductionVersions
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
wiki updated!
Thanks !!!
Hi pof, hi others!
Great job!!! I am sorry I could not react during the week. I should "meet" my friend via internet soon - so we will report our progress.
Cheers
Hans
hi everybody,
it´s me, hans jensen´s friend, who had the problem with flashing. i am sorry, my englisch knowledge is poor, however i hope, that you will understand me. very much thank to all, who have engaged in my problem. espetially thanks go to holywood63a, because he sorted out my problem.
but attention, the command "SET" may not be typed with upper case, as noted above, but with lower-case letters - "set", then!
holywood63a, pof, i invite you to beer, when you are going to prague 8) ...
xxjohn said:
but attention, the command "SET" may not be typed with upper case, as noted above, but with lower-case letters - "set", then!
holywood63a, pof, i invite you to beer, when you are going to prague 8) ...
Click to expand...
Click to collapse
Glad it is working, updated the wiki with lowecase "set".
thanks for the beer!! :wink:
;-)
F..k, xxjohn told me he speaks no English! I believe he had to be sooo happy that he has forced himself to write his contribution here ;-)
Hans Jensen's friend, let me know if you ever find ROM upg!!
You're very welcome as for the set command restoring your OS. Mine still has some glitches but runs until I can find a flashable ROM for the 300mhz version.
If you ever find a ROM that will flash to it, can you post to this thread?
Thanks!
And not sure I'll ever make my way to Prague or not, but would love to! I could if you sent me pre-paid flight vouchers for two adults and a child though! *smiling*
Hello,
Can you enter into the bootloader of the preproduction version of the Hermes, issue these commands and post the output here?
Code:
info 2
info ?
checkimage
info 3
Hopefully this will give us a clue on how to modify the Hermes roms to make them possible to flash into preproduction versions.
Also check if your bootloader has any of these commands, not present in the production versions: d2s, s2d, help
And tell me the IPL / SPL versions you see when your device boots.
If you want more info check this page, you can compare with the production Hermes bootloader:
http://wiki.xda-developers.com/index.php?pagename=Hermes_BootLoader
Note: "info 3" could hang the mtty console sometimes, do it the latest.
cheers!
Hi Guys,
I'm in the same boat as I've just been given a pre-production model of the Dopod 838 Pro but my main problem is that the ROM language is in Chinese! No problem if I could understand it but I'm trying to install a WWE ROM but have been put off by holywood63a experiences. Has anybody found a solution to this or is there another way I can change the language?
@pof: Anyway, here is the info you requested
USB>info 2
HTCS00000000jR*¥HTCE
USB>info ?
Block 0x0(0) is Reversed block
Block 0x1(1) is Reversed block
Block 0x2(2) is Reversed block
Block 0x3(3) is Reversed block
Block 0x4(4) is Reversed block
Block 0x5(5) is Reversed block
Block 0x6(6) is Reversed block
Block 0x7(7) is Reversed block
Block 0x8(8) is Reversed block
Block 0x9(9) is Reversed block
Block 0xA(10) is Reversed block
Block 0xB(11) is Reversed block
Block 0xC(12) is Reversed block
Partition[0], type=0x20, start=0x2, total=0x18FE
Partition[1], type=0x23, start=0x1900, total=0x1700
Partition[2], type=0x25, start=0x3000, total=0x1B300
CE Total Length(with sector info) = 0x3D51800
CE CheckSum Length(without sector info) = 0x3C60000
USB>checkimage
Command error !!!
USB>info 3
HTCSH
USB>info 6
HTCST ÚÈÒHTCE
USB>info 7
HTC Integrated Re-Flash Utility, Common Base Version : 0.05
Device Name: H, Bootloader Version : 0.94
Built at: Feb 21 2006 14:11:43
Copyright (c) 1998-2005 High Tech Computer Corporation
CPU ID = 0x41129200
USB>info 8
Block 0x0(0) is Reversed block
Block 0x1(1) is Reversed block
Block 0x2(2) is Reversed block
Block 0x3(3) is Reversed block
Block 0x4(4) is Reversed block
Block 0x5(5) is Reversed block
Block 0x6(6) is Reversed block
Block 0x7(7) is Reversed block
Block 0x8(8) is Reversed block
Block 0x9(9) is Reversed block
Block 0xA(10) is Reversed block
Block 0xB(11) is Reversed block
Block 0xC(12) is Reversed block
Partition[0], type=0x20, start=0x2, total=0x18FE
Partition[1], type=0x23, start=0x1900, total=0x1700
Partition[2], type=0x25, start=0x3000, total=0x1B300
CE Total Length(with sector info) = 0x3D51800
CE CheckSum Length(without sector info) = 0x3C60000
Hope all this helps someone to come up with a solution.
Cheers
Oz
omaqsood, thanks for the info, but to see exactly WHY and WHERE it fails, we need a full USB capture of the ROM Upgrade process, to do it download HHD USB Monitor, install it and start a new capture, click on the second tab where it says "full decode" and then upgrade the rom until it fails, then stop the capture and export it as TEXT (no unicode), zip it and post the results here.
After that, connect using mtty and type "set 14 0" and "task 8" to return to your previous rom.
Hopefully this will show where the problem is and would give us a clue on how to "adapt" a rom or modify the RomUpgradeUt for flashing preproduction units.
I followed your instructions as well as I could but couldn't find the "full decode" option. I've attached the output as you asked.
I hope it helps.
oops, i'm sorry but the log only contains activesync info, GetDeviceData.exe and EnterBL.exe, and when device enters into BootLoader USB is disconnected and LOG stopped, so it's unuseful
Instructions again, I hope this time will be more useful:
1) Disable activesync on your computer by right click on activesync icon -> connection settings -> uncheck "allow USB connections".
2) Put your device in BootLoader mode
3) Connect device to computer using USB cable.
4) Start USBMonitor.
5) File -> New session -> USB Monitor -> Select USB device where your phone is connected -> Check "request view" -> Finish
6) In the upper part there are two tabs: basic and complete. Click on "Complete".
7) click on RomUpgradeUt.exe and start the Rom Update Process, if everything went fine you should see all the USB traffic output on USB monitor window.
8 ) when rom upgrade fails, click on Edit -> Export and Save as type "ANSI Text files".
9) Save the file and zip it.
10) Go to mtty and issue the bootloader commands "set 14 0" and "task 8".
11) Upload the zipped file here again or put it on xda-dev FTP if it is too big.
Hello,
i have try to flash my hermes to wm6, but during the flash it breaks. then i have flashed the device via sd card to the original rom. it works, but now freezed the device in the windows mobile boot screen.
Infos from the device:
T-Mobile Start Screen:
M 05 / S 04 / B 05
D 1.21 / No GSM
Bootloader Screen:
Herm300 / IPL-1.01
Herm300 / SPL-2.03
Infos from mtty:
info 2: HTCSF kEØ(HTCE
info 3: HTCSH
info 4: HTCS Lœ3ÆHTCE
info 6: HTCST ÚÈÒHTCE
info 7:
HTC Integrated Re-Flash Utility, Common Base Version : 1.51d
Device Name: HERM100, Bootloader Version : 2.03
Built at: Jun 16 2007 01:57:22
Copyright (c) 1998-2006 High Tech Computer Corporation
CPU ID=0x41129200
Main CPLD version=0x5
Upper CPLD version=0x4
Main Board version=0x5
info 8:
Block 0x0(0) is Reversed block
Block 0x1(1) is Reversed block
Block 0x2(2) is Reversed block
Block 0x3(3) is Reversed block
Block 0x4(4) is Reversed block
Block 0x5(5) is Reversed block
Block 0x6(6) is Reversed block
Block 0x7(7) is Reversed block
Block 0x8(8) is Reversed block
Block 0x9(9) is Reversed block
Block 0xA(10) is Reversed block
Block 0xB(11) is Reversed block
Block 0xC(12) is Reversed block
Partition[0], type=0x20, start=0x2, total=0x18FE
Partition[1], type=0x23, start=0x1900, total=0x1700
Partition[2], type=0x25, start=0x3000, total=0x1B400
Partition[3], type=0x4, start=0x1E400, total=0x1C400
CE Total Length(with sector info) = 0x3D72000
CE CheckSum Length(without sector info) = 0x3C80000
Task 32: Level = FF (no SuperCID)
KITL down´t work
to do a flash from the sd card works, but it breaks with a red number 00028002 or 00068002 on the screen. then the device reboots and nothing changed.
if i try to flash witah a tool (for example ruuwrapper.exe) it breaks by 7 %.
i have made log files with usbmon and saved them in ansi and uni format. but i don´t know where i can place them, tah you can see them. thay are about 8-9 mb.
what can i do ?
who can help me?
i hope my english isn´t too bad ;-) !
HTCSF kEØ(HTCE means corrupted CID, and since you have no KITL, and NO GSM, and are stuck in Windows Mobile screen, unless you can flash the original rom (and I don't think you can...), you have three choices:
1. Send it to www.imei-check.com and they can do a JTAG reflash.
2. Have a repair center replace the motherboard
3. Buy another unit, and keep your for spare parts
drummer10630 said:
HTCSF kEØ(HTCE means corrupted CID, and since you have no KITL, and NO GSM, and are stuck in Windows Mobile screen, unless you can flash the original rom (and I don't think you can...), you have three choices:
1. Send it to www.imei-check.com and they can do a JTAG reflash.
2. Have a repair center replace the motherboard
3. Buy another unit, and keep your for spare parts
Click to expand...
Click to collapse
What about a "task 28" in mtty?
first mistake was not reading directions lol.. you should of had SPLv7 flashed to your phone before you started. there is a whole section in the wiki on bricks you might want to read as well as a whole 60 something page thread on bricks which might help you out. my best guess is send it in for repair or buy another and save the brick for parts. before SPLv1 there where lots of bricks. you also might consider sending your phone to Oli or pof so they can use it for tests if there still doing hermes work
Sorry if i hijack this thread.
but i have the same problem.
corrupted cid, No KITL, stuck @ windows screen.
But the gsm are still okay.
Any solution ??
Cos i have try all the solution here.
Trying upgrade using the orange rom its say device id error
using no id rom update still the same.
using sd card got the same error as batterie
help will be appreciated
thanks
http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
I was in the repaircenter and they will change the complete device. in a few day i will get a new hermes and if i have a little bit luck i have to pay nothing.
if i will have more luck, i will have a mda touch.
when i will have the mda touch, what do i have to look for ???
what can i do with it and what not ?
what "mußt" i do ???
thank you for the help ...
I am sorry for your problems but it still amazes me that people are still flashing there phones without flashing HardSPL first.
I am interested as to why you did not flash HardSPL first, is the information too deeply buried or not easily found?
I didn´t found the information.
i have flashed my hermes about 10 - 15 times with different roms and operationsystems (wm 5, wm 6, radiopatch 1.xx, splash screen, own cooked roms, ..., up and down) and had no problems.
i think the last rom was not for the hermes device.
now i flash first hard spl and then i will try again all the roms ...
without the bricked device i have never heard about mtty, hard-spl, flash by sd card, ... and so on. so i think it was good for me, that i have bricked the device ;-)
learning by doing ...
without a little bit luck i will have in a few weeks two devices, one hermes (mda vario II) and one mda touch ... then i will use the hermes for test and the touch for work ...
thankxxx
i already read those wiki.
the only solution there is
Flash any shipped ROM matching your CID, if such rom is not available wait until your carrier releases it or send it to repair or warranty...
The problem was the device was corrupted cid so i cannot upgrade using the shipped rom (always country id error)
i try to bring to service center.its say it need to be replaced motherboard. and sadly its not cover the guarantee cos not official rom.
drummer10630 said:
http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
Click to expand...
Click to collapse
also for the hard spl question. Usually i hard spl first if i upgrade using non official rom. but its seem my friend doesn't know hardspl and upgrade it directly.
thx.
i´m waiting ...
now i have an new device ... they have changed it ! yippie ... ...
so first i have to flash hard spl !
is there anything else i must have to do ???
batterie said:
now i have an new device ... they have changed it ! yippie ... ...
so first i have to flash hard spl !
is there anything else i must have to do ???
Click to expand...
Click to collapse
Go to MrVanx guides and read up on upgrading and stuff. The guides will let you know what must be done.
I'm sure everyone is getting sick of these posts. This is the reason I have spent about 2 days reading post after post, along with every how-to ever.
I have tried a couple different versions of Hard-SPL.
Olipro 2.10
SPL-2.03
I have problems when trying to run the radio only updates as well as the updates from the Hermes website for ATT. It either gives me error 262 at 0% or 12%.
Here is the printout from mtty
Cmd>info 8
Block 0x0(0) is Reversed block
Block 0x1(1) is Reversed block
Block 0x2(2) is Reversed block
Block 0x3(3) is Reversed block
Block 0x4(4) is Reversed block
Block 0x5(5) is Reversed block
Block 0x6(6) is Reversed block
Block 0x7(7) is Reversed block
Block 0x8(8) is Reversed block
Block 0x9(9) is Reversed block
Block 0xA(10) is Reversed block
Block 0xB(11) is Reversed block
Block 0xC(12) is Reversed block
Partition[0], type=0x20, start=0x2, total=0x18FE
Partition[1], type=0x23, start=0x1900, total=0x1700
Partition[2], type=0x25, start=0x3000, total=0x19E00
Partition[3], type=0x4, start=0x1CE00, total=0x1DA00
CE Total Length(with sector info) = 0x3AA7000
CE CheckSum Length(without sector info) = 0x39C0000
If I try to run task 2a it doesn't tell me anything, just goes back to CMD>
For one, mtty always says CMD> instead of USB>. Is that a problem and how would I fix it. I was assuming it didnt matter.
Can someone tell me exactly what radio I should flash? or the most successful radio that I can flash? I don't care if it is old, I just want to make phone calls. I have even tried to flash the nbh from ubuntu with no success.
Also, is hard-spl V9 any better? I haven't tried it yet. i am going to be doing that right after I post this. I am kind of lost in all of this and have no idea where to go from here. I wish I knew a way to figure out if it is a bad physical radio.
Thanks,
Ray
Sorry to hear it. My Hermes if in the "no GSM" mode to.
My solution, I ended up being getting a Kaiser.
Hope you can find a way to revive yours.
Hi,
It seems that you are not the only one to have a problem with your radio rom. There is a thread here: http://forum.xda-developers.com/showthread.php?t=349461
Could you give a bit more details about what happens before your problem?
- Which radio rom was on your htc before
- Did it stop to work suddenly? or did the problem happen when flashing a new rom?
- Which method did you use for flashing (pc connection or sdcard?)
- Which release of hermes did you have (herm100,200,300?)
- etc...
Thanks
1. My radio was 1.34
2. It just stopped working. Had never been upgraded
3. I tried flashing via pc and I transferred a file to the phone and tried it that way. I may not be doing it correctly though, so maybe I need a point in the right direction for which files to download and flash. Does it have to be from the sd card or can I transfer it to the phone memory.
4. It is a Cingular 8525 HERM100 it says.
Before I put Hard-SPL on it said SPL 1.11 IPL 1.01
Then I started trying to flash several thousand different types of upgrades. Radio rom only, custom RUU, Official HERMES upgrade, etc.
The only progress I made was one time it started flashing and after it failed, the phone restarted and said ATT instead of Cingular.
I have followed steps 4 and 5 on the bricked heremes thread.
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
This is what Im talking about:
USB> password 0000000000000000
USB> set 1e 1
USB> erase a0040000 c80000
USB> erase a0cc0000 c80000
USB> erase a1940000 640000
USB> set 1e 0
After that, I still cant flash anything.
I think it is out of warranty. I dont care to open it up if I have to. Is the radio (that might be corrupted) on a removable board or chip?
I can boot into windows and use it as a PDA, it just has no gsm and no imei
did you solve the problem.the same thing hapeened to me.helpppp
SOLUTION!!!
I had a bricked hermes like everyone else. It had the no GSM message and could not flash anything couldn't even get MTTY to recognize it. I finally got it!!!! I flashed the Hard SPL using the SD Card Method. After I flashed the Official Stock Rom my radio is back. (It did take 2 tries to get the Rom to flash and again I used the SD Card method) I hope you can use this. Just incase you don't know use a 2 GB SD CARD and it MUST BE 2 GB or smaller. put the attached exe file and the .nbh file. Rename the .nbh file to HERMIMG.nbh. Open bootloader and it will start the update after you press start button when prompted. It worked for me and hope it will work for you!!!
I'm new to HTC devices and to XDA. I received the device with 6.1 Professional and I wanted to see if 5 was any faster. I thought I was downgrading from 6.1 to 5 but apparently I flashed the bootloader to SPL 2.03.
I can access the bootloader screen (power + ok + soft reset). When I turn on the device normally, I get a green light but nothing else happens. I've had it for less than 24 hours so I hope I didn't brick it already. I jumped into the flashing thing way too quick. I did some research and tried several different things. (Mtty + spl-1.04.nb = Command Error!!!!!)
If you've got any ideas I'd love some help, please!
Just to add a few more details to this:
The tri-color screen (which I've learned is the bootloader?):
HERM100
IPL-1.04
HERM100
SPL-2.03
What happened:
I bought the phone with Windows Mobile 6 Professional (I think it was 6.1). The ROM on the device was Schaps 4.x (not entirely sure if it was 4.3 or not). In a fury of excitement and rushing, I was thinking (and I don't know why) that a 300KB SPL file was going to bring me back to WM5 and hopefully make the device move a bit quicker. When I updated the device, the update utility said my old version (Schaps 4.x) and the new version (of the SPL). I clicked update, and within 10 seconds, I had nothing more than a green light and no display.
I can access the tri-color screen, I've tried the microSD card methods (every ROM gets to 100% then the device completely shuts off. The only way to get it back on is to either pull the battery and press power (no display/green light) or power + ok + reset.
To make things more complicated I have access to two operating systems at the moment: Windows 7 (Beta) and Ubuntu 8.04. Windows 7 seems to work great with the device.
In WMDC I can't see the device since it's in the tri-color screen, but I am able to see it via mtty and the RUU installers when needed.
I've had the device for probably 1 day solid, is there any way to unbrick this puppy? Is there a way to rewrite the SPL (mrvanx doesn't have the CustomRUU SPL files any longer).
If you need more info, let me know. All my knowledge from flashing ROMs and all this terminology is from this site so thanks to all of you! I also have a background in computers (Windows/Linux - 10yrs) hardware and programming C (the basics anyway) and also web programming in PHP/SQL. I know how to fix most PC problems I've come across but this is simply beyond me. HOWEVER! I am totally willing to take on the challenge of learning a semi-new platform.
whats the link to the file you tried to flash? It sounds like you have tried to flash something no designed for hermes, but without knowing what it is you originally tried to flash very little help can be given. Can you still access the tri colour bootloader?
If you can and you have a full rom you can use, then these files will let you try and flash the windows os back on the device
http://wiki.xda-developers.com/index.php?pagename=Hermes_CustomRUU
try flashing this rom
http://rapidshare.com/files/18315008/RUU_HER_CINGULAR_2.06.502.3_1.34.00.10_SPL1.04.exe
if it fails at 100% try extracting the files from the exe file ,simply right click on the exe installer and click extract to then open the folder and right click again on the ruu_inside.exe and extract those to a ruu_inside folder (you need winrar installed to be able to do the extracting) Now extract the hermes_customRUU files in to a folder and copy the nbh file from the ruu_inside folder to the folder you extracted the custom ruu files to and install from there. If that also fails then i would try this file which contains no spl or radio
It will at least give you some indication of where it is failing if you are able to flash the OS
http://rapidshare.com/files/18475719/Hermes_WM6_vanilla.rar
Another option is to try flashing this rom
http://rapidshare.com/files/52912451/RUU_Hermes_TMO_UK_3.60.110.2_6275_1.50.00.00_108_Test.exe
also add to any comments you make and say where you are from, where you bought the hermes and as i have already said what it was you were trying to flash that got it in this state in the first place
To start off, I'm from Massachusetts. I bought the phone off craigslists from a guy in Connecticut (about 1hr from where I live). He's actually a good guy, he's trying to figure this out also.
The original flash is as follows: I went to MrVanx's site, tried to download 2.03 (SPL Downgrade Guide). The link was dead (to the file) so I googled the filename and found it on.
HERM_SPL_2.03_CUSTOMRUU.rar:
http://rapidshare.com/files/151828006/HERM_SPL_2.03_CUSTOMRUU.rar
I found this my Googling the above filename and copying and pasting the rapidshare link from the description in the second result.
I then downloaded Microsoft ActiveSync 4.5 and connected the device. (At this point my 8525 was running fine with WM6.1 (Schaps 4.x). I went through the RUU provided above (SPL_2.03_CUSTOMRUU) and it showed the version I had installed (Schaps) and the new version it was going to flash. I went through all the prompts and it took roughly 10 seconds to flash the device. After which the phone can no longer boot. I can access the bootloader screen (IPL-1.04/SPL-2.03) and I've tried flashing quite a few ROMs to no avail (4 or 5 OEM Cingular ROMS), VP3G ROM, Schaps 4.3 ROM.
In the RUU it never shows my old version (it's left blank). It'll show the new version (whatever the ROM is). Both my PC and device reach 100% and the RUU says it's completed successfully. The device hits 100% for about 4-5 seconds and then shuts off. When I power it up, I receive the green power light and nothing else on the screen.
I can still access the tri-color bootloader screen to this day, just whatever I flash seems not to work.
I've also tried using MTTY and ran all the INFO commands and the task 28 command and successfully reformated the device. (Not sure if that changes anything bootloader wise, but it's still 1.04/2.03 (IPL/SPL)).
I've downloaded the ModifiedRUUUpdater-v2 and I'm downloading one of the original Cingular ROMs as we speak. I'll post back later after I've tried all of your links/ROMs.
Thank you!
Your third link (TMO_UK) - I assume is T-Mobile.. my device isn't SuperCID so I don't think that'll work, but I'll try after I attempt the previous three.
Thanks,
Shawn
Well so far Vanilla ROM and Cingular ROM you provided failed to work. I received the 00068002 error when doing SD card method (copying files from W7 box). On my XP box (copied from XP to SD) it shows "Loading..." then the screen goes right back to the bootloader screen. I'm starting to wonder if there is a problem with my machines.
W7 is beta = a problem.
XP has bad HDD = a problem.
I'm going to install XP over W7 and try all these steps again.
...I'll be back!
EDIT: To make things worse, W7 is 64bit, so perhaps thats giving me some trouble? I'm going to XPH SP3 32bit. I'll be back in a couple hours with results then.
Ok, sorry for the multiple posting but here's the results on a fresh install of Windows XP SP3 with (.NET 1.1 and 2.0)...
Cingular 2.06 ROM - Can't find device (Error 260)
Vanilla ROM - Can't find device (Error 260)
Schaps 4.30 - Found device (Error 270 - Image Corrupt)
MTTY 1.16 - Works fine
MTTY 1.16 - INFO 8
Code:
Block 0x0(0) is Reversed block
Block 0x1(1) is Reversed block
Block 0x2(2) is Reversed block
Block 0x3(3) is Reversed block
Block 0x4(4) is Reversed block
Block 0x5(5) is Reversed block
Block 0x6(6) is Reversed block
Block 0x7(7) is Reversed block
Block 0x8(8) is Reversed block
Block 0x9(9) is Reversed block
Block 0xA(10) is Reversed block
Block 0xB(11) is Reversed block
Block 0xC(12) is Reversed block
Partition[0], type=0x20, start=0x2, total=0x18FE
Partition[1], type=0x23, start=0x1900, total=0x1700
Partition[2], type=0x25, start=0x3000, total=0x1CF00
Partition[3], type=0x4, start=0x1FF00, total=0x1A900
CE Total Length(with sector info) = 0x40DF800
CE CheckSum Length(without sector info) = 0x3FE0000
MTTY 1.16 INFO 7
Code:
HTC Integrated Re-Flash Utility, Common Base Version : 1.51d
Device Name: HERM100, Bootloader Version : 2.03
Built at: Jun 16 2007 01:57:22
Copyright (c) 1998-2006 High Tech Computer Corporation
CPU ID=0x41129200
Main CPLD version=0x5
Upper CPLD version=0x4
Main Board version=0x6
MTTY 1.16 - TASK 32
Code:
Level = FF
MTTY 1.16 - TASK 28
Code:
Storage format start
Write Nand Success
dwBlockToWrite = 13
Storage start block: 511
Storage Total block: 425
Total Bad Block in CE: 0
NeedToEraseBlockStart: 524
NeedToEraseBlockEnd: 936
Storage format success
MTTY 1.16 - checkimage
Code:
IPL CRC checksum = 0x38E3AF5A
SPL CRC checksum = 0xAE0F1EC4
CE CRC checksum = 0x7EFF2612
ExtROM CRC checksum = 0xED0630B1
Radio Image CRC checksum = 0xEA15A16D
try disabling active sync usb connections before trying to flash
I've done it without it checked and with it checked. Doesn't seem to work either way. I attempted to flash the AT&T WM6 ROM and once it said "Upgrade Completed. UPGRADE SUCCESS" I did a soft reset and received just received the green light (the screen still black).
I'm going to start a new thread all together with a more broad topic than what I assumed to be the problem because I don't think the SPL version matters at this point. I appreciate your help thus far and perhaps maybe if you think of a different approach on my situation you can post it?
Thank you again!
Solution for SPL2.03
hi there i am facing the same problem with my spv m3100 and tried out all the tools and tricks that u mentioned in your thread but all in vain....
your thread is almost 3months ago...
i would like to ask.. did u find any solution for that problem of spl2.03....?
if so then please share and help me...
Thanks.. i am waiting for your reply
Dear all,
I am having big trouble with my dopod 838 pro, issues is:-
- I can flash a after market ROM - wm6.1 from PDAVIET
- The unit has no GSM when turn on
- the unit has "IPL-1.01, SPL - 1.40.olipro"
- I can't upgrade to Hard-SPL v7.0 nor Hard-SPL v9.0 now, but it can be before.
- can't flash the radio via SD card, it keep stuck at about 10% stage.
can anyone help to solve this problem and make my unit working properly again?
many thanks.
Winston
P.S.
It can't run "Free HTC Hermes SIM & CID Unlocker *New* version v3a" fully, always has connection error at the last flashing stage.
FYI
Cmd>checkimage
IPL CRC checksum = 0x24C42773
SPL CRC checksum = 0x921BC30
CE CRC checksum = 0xCDD28C10
ExtROM CRC checksum = 0x62D771F3
Radio Image CRC checksum = Checksum: Wait interpreter timeout
0x0
Cmd>
Cmd>
Cmd>
Cmd>info 8
Block 0x0(0) is Reversed block
Block 0x1(1) is Reversed block
Block 0x2(2) is Reversed block
Block 0x3(3) is Reversed block
Block 0x4(4) is Reversed block
Block 0x5(5) is Reversed block
Block 0x6(6) is Reversed block
Block 0x7(7) is Reversed block
Block 0x8(8) is Reversed block
Block 0x9(9) is Reversed block
Block 0xA(10) is Reversed block
Block 0xB(11) is Reversed block
Block 0xC(12) is Reversed block
Partition[0], type=0x20, start=0x2, total=0x18FE
Partition[1], type=0x23, start=0x1900, total=0x1900
Partition[2], type=0x25, start=0x3200, total=0x1FE00
Partition[3], type=0x4, start=0x23000, total=0x1C000
CE Total Length(with sector info) = 0x4718000
CE CheckSum Length(without sector info) = 0x4600000
If you didn't have HARDSPL on the phone prior to the flash there is a WIKI about how to recover from a bricked phone. If you didn't have NO GSM errors before - EVER you can still get it back. Go to the WIKI section for the HERMES and try the steps there. Your radio is probably just corrupted not damaged but it might be.
Try the steps (ALL in the WIKI) then post back.
I had the same problem but my GSM radio is dying. Was able to get it back partially but it dies again so I'm assuming a hardware problem with my phone. If yours worked before the flash WITHOUT any GSM errors before you should be ok.
hi stim141,
thanks very much for your quick reply.
refer to the wiki page -
http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
i am confusing what's my SPL version and bootloader (HTC_BOOT) version ?
- my unit shows "IPL-1.01, SPL - 1.40.olipro"
- there's no radio version i can find in my unit
so what's my SPL version and bootloader (HTC_BOOT) version ?
thanks.
Your spl is the 1.4 and the bootloader is the first number. The chart in the WIKI can be confusing. It looks as though you should be able to flash just a radio rom. First suggest you try to flash HardSPL. REALLY recommend you flash using the SD card (there is instructions on the Wiki page) because you can have problems with Activesync. Try reflashing just a radio ROM first using the SD card it may come back.
stim141 said:
Your spl is the 1.4 and the bootloader is the first number. The chart in the WIKI can be confusing. It looks as though you should be able to flash just a radio rom. First suggest you try to flash HardSPL. REALLY recommend you flash using the SD card (there is instructions on the Wiki page) because you can have problems with Activesync. Try reflashing just a radio ROM first using the SD card it may come back.
Click to expand...
Click to collapse
Hi Again,
My SPL is 1.40.olipro, doesn't mean it is HardSPL already?
The second picture has already shown that the unit can't flash the radio via SD card, it keep stuck at about 10% stage.
any solution?
many thanks.
1.40 is an older unsafe version of Hard SPL. V7 (SPL : 2.10 oli) is considered the best for the layperson.
See if you can find what your radio rom was before you tried to unlock it as it will now be 1.16. Its best to re-install the stock radio rom or it may brick permanently. Always go back to stock....
Cheers...
sorry i have no idea what radio version is my original radio version.
can i just try to flash all version RADIOs one by one to figure it out?
ultramag69 said:
Its best to re-install the stock radio rom or it may brick permanently.
Click to expand...
Click to collapse
As I said before.....
my unit is still dead.
I've got a Hermes with the same issue. If the MYYT commands don't work, it's a hardware thing. I replaced the motherboard on my Hermes and it works great now (was curious if it would work and how successful i'd be so i just did it today and it's looking great).
As kareem9nba said, if the fixes given DON'T work its hardware and has to be replaced. Look on ebay, you might be REALLY lucky and get a fully functional Hermes for cheap, as it may have a problem that yours doesn't and can be used for parts, I know mines made up of 2 different units....
Had a Hermes where the screen went bung, found another on ebay that apparently had same problem as yours... Now I have 1 working Hermes and a few extra spare parts...
Cheers...