Dear all,
I am having big trouble with my dopod 838 pro, issues is:-
- I can flash a after market ROM - wm6.1 from PDAVIET
- The unit has no GSM when turn on
- the unit has "IPL-1.01, SPL - 1.40.olipro"
- I can't upgrade to Hard-SPL v7.0 nor Hard-SPL v9.0 now, but it can be before.
- can't flash the radio via SD card, it keep stuck at about 10% stage.
can anyone help to solve this problem and make my unit working properly again?
many thanks.
Winston
P.S.
It can't run "Free HTC Hermes SIM & CID Unlocker *New* version v3a" fully, always has connection error at the last flashing stage.
FYI
Cmd>checkimage
IPL CRC checksum = 0x24C42773
SPL CRC checksum = 0x921BC30
CE CRC checksum = 0xCDD28C10
ExtROM CRC checksum = 0x62D771F3
Radio Image CRC checksum = Checksum: Wait interpreter timeout
0x0
Cmd>
Cmd>
Cmd>
Cmd>info 8
Block 0x0(0) is Reversed block
Block 0x1(1) is Reversed block
Block 0x2(2) is Reversed block
Block 0x3(3) is Reversed block
Block 0x4(4) is Reversed block
Block 0x5(5) is Reversed block
Block 0x6(6) is Reversed block
Block 0x7(7) is Reversed block
Block 0x8(8) is Reversed block
Block 0x9(9) is Reversed block
Block 0xA(10) is Reversed block
Block 0xB(11) is Reversed block
Block 0xC(12) is Reversed block
Partition[0], type=0x20, start=0x2, total=0x18FE
Partition[1], type=0x23, start=0x1900, total=0x1900
Partition[2], type=0x25, start=0x3200, total=0x1FE00
Partition[3], type=0x4, start=0x23000, total=0x1C000
CE Total Length(with sector info) = 0x4718000
CE CheckSum Length(without sector info) = 0x4600000
If you didn't have HARDSPL on the phone prior to the flash there is a WIKI about how to recover from a bricked phone. If you didn't have NO GSM errors before - EVER you can still get it back. Go to the WIKI section for the HERMES and try the steps there. Your radio is probably just corrupted not damaged but it might be.
Try the steps (ALL in the WIKI) then post back.
I had the same problem but my GSM radio is dying. Was able to get it back partially but it dies again so I'm assuming a hardware problem with my phone. If yours worked before the flash WITHOUT any GSM errors before you should be ok.
hi stim141,
thanks very much for your quick reply.
refer to the wiki page -
http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
i am confusing what's my SPL version and bootloader (HTC_BOOT) version ?
- my unit shows "IPL-1.01, SPL - 1.40.olipro"
- there's no radio version i can find in my unit
so what's my SPL version and bootloader (HTC_BOOT) version ?
thanks.
Your spl is the 1.4 and the bootloader is the first number. The chart in the WIKI can be confusing. It looks as though you should be able to flash just a radio rom. First suggest you try to flash HardSPL. REALLY recommend you flash using the SD card (there is instructions on the Wiki page) because you can have problems with Activesync. Try reflashing just a radio ROM first using the SD card it may come back.
stim141 said:
Your spl is the 1.4 and the bootloader is the first number. The chart in the WIKI can be confusing. It looks as though you should be able to flash just a radio rom. First suggest you try to flash HardSPL. REALLY recommend you flash using the SD card (there is instructions on the Wiki page) because you can have problems with Activesync. Try reflashing just a radio ROM first using the SD card it may come back.
Click to expand...
Click to collapse
Hi Again,
My SPL is 1.40.olipro, doesn't mean it is HardSPL already?
The second picture has already shown that the unit can't flash the radio via SD card, it keep stuck at about 10% stage.
any solution?
many thanks.
1.40 is an older unsafe version of Hard SPL. V7 (SPL : 2.10 oli) is considered the best for the layperson.
See if you can find what your radio rom was before you tried to unlock it as it will now be 1.16. Its best to re-install the stock radio rom or it may brick permanently. Always go back to stock....
Cheers...
sorry i have no idea what radio version is my original radio version.
can i just try to flash all version RADIOs one by one to figure it out?
ultramag69 said:
Its best to re-install the stock radio rom or it may brick permanently.
Click to expand...
Click to collapse
As I said before.....
my unit is still dead.
I've got a Hermes with the same issue. If the MYYT commands don't work, it's a hardware thing. I replaced the motherboard on my Hermes and it works great now (was curious if it would work and how successful i'd be so i just did it today and it's looking great).
As kareem9nba said, if the fixes given DON'T work its hardware and has to be replaced. Look on ebay, you might be REALLY lucky and get a fully functional Hermes for cheap, as it may have a problem that yours doesn't and can be used for parts, I know mines made up of 2 different units....
Had a Hermes where the screen went bung, found another on ebay that apparently had same problem as yours... Now I have 1 working Hermes and a few extra spare parts...
Cheers...
Related
Just unlocked my Orange SPV M3100 using imei check. I remember that there was a warning that the unlocker would not work if the radio version was later than 1.06
Anyway now that I've unlocked it I want to try out some of the other roms out there which I have later radio version 1.07.
Need to know if the newer roms would work with my phone before going ahead. Thanks
zen123 said:
Just unlocked my Orange SPV M3100 using imei check. I remember that there was a warning that the unlocker would not work if the radio version was later than 1.06
Anyway now that I've unlocked it I want to try out some of the other roms out there which I have later radio version 1.07.
Need to know if the newer roms would work with my phone before going ahead. Thanks
Click to expand...
Click to collapse
Yes they do - my Orange M3100 (unlocked by imeicheck) is running the i-mate JasJam ROM, with a T-Mobile SIM.
EDIT: I forgot to add - the unlock seems also to have removed the CID check, so that upgrading the ROM was really simple (didn't have to run the upgrade twice as others have reported).
battletank said:
zen123 said:
Just unlocked my Orange SPV M3100 using imei check. I remember that there was a warning that the unlocker would not work if the radio version was later than 1.06
Anyway now that I've unlocked it I want to try out some of the other roms out there which I have later radio version 1.07.
Need to know if the newer roms would work with my phone before going ahead. Thanks
Click to expand...
Click to collapse
Yes they do - my Orange M3100 (unlocked by imeicheck) is running the i-mate JasJam ROM, with a T-Mobile SIM.
EDIT: I forgot to add - the unlock seems also to have removed the CID check, so that upgrading the ROM was really simple (didn't have to run the upgrade twice as others have reported).
Click to expand...
Click to collapse
Thanks for the reply. How do you find the JasJam rom by the way? I'm looking at that one or maybe the Dopod rom.
It does seem quicker. More importantly, I find that it's holding onto UMTS signals much longer, and almost never reverting down to GPRS. I'm sure the Dopod ROM with the same radio version would be the same in this regard.
battletank said:
EDIT: I forgot to add - the unlock seems also to have removed the CID check, so that upgrading the ROM was really simple (didn't have to run the upgrade twice as others have reported).
Click to expand...
Click to collapse
So, i guess this means that do you have a SuperCID after runing their unlocker, right?
Can you post the output you get from the bootloader when issuing these commands?
Code:
info 2
info 4
info 7
info 8
Info on how to do it is here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_BootLoader
Let me know if you neet any asistance.
Thanks!
That was certainly my assumption.
Here's the output from those info commands:
Code:
USB>info 2
HTCSORANG001ã¤USB>info 4
IsAllBytesTheSame-: dwLength=8, bResult=0
HTCSORANG001ã¤USB>info 7
HTC Integrated Re-Flash Utility, Common Base Version : 1.50a
Device Name: H, Bootloader Version : 1.04
Built at: May 26 2006 20:17:35
Copyright (c) 1998-2006 High Tech Computer Corporation
CPU ID=0x41129200
Main CPLD version=0x5
Upper CPLD version=0x4
Main Board version=0x5
USB>info 8
Block 0x0(0) is Reversed block
Block 0x1(1) is Reversed block
Block 0x2(2) is Reversed block
Block 0x3(3) is Reversed block
Block 0x4(4) is Reversed block
Block 0x5(5) is Reversed block
Block 0x6(6) is Reversed block
Block 0x7(7) is Reversed block
Block 0x8(8) is Reversed block
Block 0x9(9) is Reversed block
Block 0xA(10) is Reversed block
Block 0xB(11) is Reversed block
Block 0xC(12) is Reversed block
Block 0x3F8(1016) is Reversed block
Partition[0], type=0x20, start=0x2, total=0x18FE
Partition[1], type=0x23, start=0x1900, total=0x1700
Partition[2], type=0x25, start=0x3000, total=0x19C00
Partition[3], type=0x4, start=0x1CC00, total=0x1DC00
CE Total Length(with sector info) = 0x3A66000
CE CheckSum Length(without sector info) = 0x3980000
battletank said:
USB>info 2
HTCSORANG001ã¤
Click to expand...
Click to collapse
mmm... doesn't seem to be SuperCID, probably is just CID Unlocked ¿?
btw, the imei check people packed their unlocker with Themida, and protected it from debuggers:
"Running debugger in system. In order to execute this program you have to quit the debugger first."
Click to expand...
Click to collapse
And it gives a communication error if you try to monitor the USB port when running it.
So, still don't know what the unlocker really does :?
I just bought a Dutch T-Mobile MDA Vario II which is sim locked. I will not pay for unlocking it, but if I can do something else to help out please let me know .
I am posting this outside of the bricked thread in despiration. I posted here http://forum.xda-developers.com/showpost.php?p=1250132&postcount=1164 for intial help.
Quick recap...
Had no GSM on boot...device info showed no radio or protocol versions.
Tried HTC_Hermes_SIM_CID_Unlock_v3a first, which might not have been the best choice. Load something (SPL i guess) then it stopped and tried recovery serval times.
Currently stuck in bootloader screen (tri-color) with this displaying:
HERM100
IPL 1.01
HERM100
SPL 1.40Olipro
Before flashing SPL was 1.11. I was instructed by digger_de to reload with new radio and select SPL 1.40 when asked... tried going to hard SPLv7 using latest CustomRRU...I selected FORCE SSPL (as per the guide) in the menu and tried to upload. Sits on "verify info on the hermes" screen then error 260 appears.
So I tried just to go to the new radio 1.41... I select SPL 1.40 from the menu..click update...get a progress screen that sits at 0% for a min or so...then error 262 displays. What do I do next?
Do I need to try KITLS or whatever, do I even have it? or do I need to use mtty and if so what commands?
I have read through the wiki and several threads, but I have not found something just like my situation.
I appreciate anyone that can point me the right direction.
Thanks,
Michael
reading more...
OK...did some more reading...ran mtty and some commands... seems radio is no there. How do I get it loaded?
Cmd>checkimage
IPL CRC checksum = 0x24C42773
SPL CRC checksum = 0x921BC30
CE CRC checksum = 0x4E705577
ExtROM CRC checksum = 0x1E9CA80
Radio Image CRC checksum = Checksum: Wait interpreter timeout
0x0
Cmd>`
Command error !!!
Cmd>
Cmd>
Cmd>info 8
Block 0x0(0) is Reversed block
Block 0x1(1) is Reversed block
Block 0x2(2) is Reversed block
Block 0x3(3) is Reversed block
Block 0x4(4) is Reversed block
Block 0x5(5) is Reversed block
Block 0x6(6) is Reversed block
Block 0x7(7) is Reversed block
Block 0x8(8) is Reversed block
Block 0x9(9) is Reversed block
Block 0xA(10) is Reversed block
Block 0xB(11) is Reversed block
Block 0xC(12) is Reversed block
Block 0x3FB(1019) is Reversed block
Partition[0], type=0x20, start=0x2, total=0x18FE
Partition[1], type=0x23, start=0x1900, total=0x1700
Partition[2], type=0x25, start=0x3000, total=0x19E00
Partition[3], type=0x4, start=0x1CE00, total=0x1DA00
CE Total Length(with sector info) = 0x3AA7000
CE CheckSum Length(without sector info) = 0x39C0000
Cmd>info 7
HTC Integrated Re-Flash Utility, Common Base Version : 1.60d
Device Name: HERM100, Bootloader Version : 1.40.Olipro
Built at: Mar 30 2007 15:10:47
Copyright (c) 1998-2007 Modified By Olipro - Hard-SPL
CPU ID=0x41129200
Main CPLD version=0x5
Upper CPLD version=0x4
Main Board version=0x6
Cmd>info 6
HTCST ÚÈÒHTCE
Hope you guys can help...I've got a long borring plane ride tomorrow..would love to play with the Herm on the plane.
Thanks!!
Michael
also...
Task 32 returns 0 ... so that means I am SuperCID right?
I am learning...slowly but surely.
MM
zerocool00 said:
I am posting this outside of the bricked thread in despiration. I posted here http://forum.xda-developers.com/showpost.php?p=1250132&postcount=1164 for intial help.
Quick recap...
Had no GSM on boot...device info showed no radio or protocol versions.
Tried HTC_Hermes_SIM_CID_Unlock_v3a first, which might not have been the best choice. Load something (SPL i guess) then it stopped and tried recovery serval times.
Currently stuck in bootloader screen (tri-color) with this displaying:
HERM100
IPL 1.01
HERM100
SPL 1.40Olipro
Before flashing SPL was 1.11. I was instructed by digger_de to reload with new radio and select SPL 1.40 when asked... tried going to hard SPLv7 using latest CustomRRU...I selected FORCE SSPL (as per the guide) in the menu and tried to upload. Sits on "verify info on the hermes" screen then error 260 appears.
So I tried just to go to the new radio 1.41... I select SPL 1.40 from the menu..click update...get a progress screen that sits at 0% for a min or so...then error 262 displays. What do I do next?
Do I need to try KITLS or whatever, do I even have it? or do I need to use mtty and if so what commands?
I have read through the wiki and several threads, but I have not found something just like my situation.
I appreciate anyone that can point me the right direction.
Thanks,
Michael
Click to expand...
Click to collapse
Quick question, the latest radios have CustomRUU 4.3 in them (i know because i repackaged them).....check the wiki. When you select your SPL version do you tick "Is it HardSPL?" ??
I think your problem can solved easily, as you have Olipro's hard SPL already in place, this allows you to flash any ROM. With the phone on the boot loader screen (the coloured bars), connect it to the PC and then run one of the radio upgrades from http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms - I currently use 1.40.30.00. If asked, select 'Hard SPL'.
If that doesn't work (i.e. you can't flash), you can try extracting the .nbh file from the radio upgrade, copy it onto a blank SD card, rename it to HERMIMG.NBH and reset the phone with the card inserted - see http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing for more information.
If you have any further problems I would strongly recommend that you spend some time reading the wiki - the answers to your questions are more than likely there.
I am having exactly the same problem as the op. When running Mtty get the same results just different checksums. (I have IPL-1.04)
When I flash just a radio rom it freezes. Does not matter if I do it via SD card or via PC.
Starting to get a bit frustrated with this and starting to get a bit too technical for me haha.
If anyone has any other ideas please let me know.
Cheers
mrvanx said:
Quick question, the latest radios have CustomRUU 4.3 in them (i know because i repackaged them).....check the wiki. When you select your SPL version do you tick "Is it HardSPL?" ??
Click to expand...
Click to collapse
Yessir...I did try that way. No go. Just sits on 0% for a min then phone restarts and PC (WinXP SP2 with .net 2) pops error 262 or whichever saying connection error.
forza said:
I think your problem can solved easily, as you have Olipro's hard SPL already in place, this allows you to flash any ROM. With the phone on the boot loader screen (the coloured bars), connect it to the PC and then run one of the radio upgrades from http://wiki.xda-developers.com/index...actedRadioRoms - I currently use 1.40.30.00. If asked, select 'Hard SPL'.
If that doesn't work (i.e. you can't flash), you can try extracting the .nbh file from the radio upgrade, copy it onto a blank SD card, rename it to HERMIMG.NBH and reset the phone with the card inserted - see http://wiki.xda-developers.com/index...SDCardFlashing for more information.
If you have any further problems I would strongly recommend that you spend some time reading the wiki - the answers to your questions are more than likely there.
Click to expand...
Click to collapse
I hope it is that easy. I appreciate your comments. Currently I do not own a SD card, but as soon as the plane lands this evening, I'll have one if you think that is the way. As for reading, I have read so much here over the past few weeks, it is crazy. That is part of the problem, there is tons of info here and on the wiki, some seems outdated, and as a new user, I wanted current instructions just to make sure I did everything correct.
Thanks,
Michael
@zerocool00: I answered you here:
http://forum.xda-developers.com/showthread.php?t=286755&p=1255936
We don't want the forum flooded with dead devices thread.... all the knowledge about dead devices is on the thread above. Please take your time to read and don't post desperately.
Closing this one.
Hello,
i have try to flash my hermes to wm6, but during the flash it breaks. then i have flashed the device via sd card to the original rom. it works, but now freezed the device in the windows mobile boot screen.
Infos from the device:
T-Mobile Start Screen:
M 05 / S 04 / B 05
D 1.21 / No GSM
Bootloader Screen:
Herm300 / IPL-1.01
Herm300 / SPL-2.03
Infos from mtty:
info 2: HTCSF kEØ(HTCE
info 3: HTCSH
info 4: HTCS Lœ3ÆHTCE
info 6: HTCST ÚÈÒHTCE
info 7:
HTC Integrated Re-Flash Utility, Common Base Version : 1.51d
Device Name: HERM100, Bootloader Version : 2.03
Built at: Jun 16 2007 01:57:22
Copyright (c) 1998-2006 High Tech Computer Corporation
CPU ID=0x41129200
Main CPLD version=0x5
Upper CPLD version=0x4
Main Board version=0x5
info 8:
Block 0x0(0) is Reversed block
Block 0x1(1) is Reversed block
Block 0x2(2) is Reversed block
Block 0x3(3) is Reversed block
Block 0x4(4) is Reversed block
Block 0x5(5) is Reversed block
Block 0x6(6) is Reversed block
Block 0x7(7) is Reversed block
Block 0x8(8) is Reversed block
Block 0x9(9) is Reversed block
Block 0xA(10) is Reversed block
Block 0xB(11) is Reversed block
Block 0xC(12) is Reversed block
Partition[0], type=0x20, start=0x2, total=0x18FE
Partition[1], type=0x23, start=0x1900, total=0x1700
Partition[2], type=0x25, start=0x3000, total=0x1B400
Partition[3], type=0x4, start=0x1E400, total=0x1C400
CE Total Length(with sector info) = 0x3D72000
CE CheckSum Length(without sector info) = 0x3C80000
Task 32: Level = FF (no SuperCID)
KITL down´t work
to do a flash from the sd card works, but it breaks with a red number 00028002 or 00068002 on the screen. then the device reboots and nothing changed.
if i try to flash witah a tool (for example ruuwrapper.exe) it breaks by 7 %.
i have made log files with usbmon and saved them in ansi and uni format. but i don´t know where i can place them, tah you can see them. thay are about 8-9 mb.
what can i do ?
who can help me?
i hope my english isn´t too bad ;-) !
HTCSF kEØ(HTCE means corrupted CID, and since you have no KITL, and NO GSM, and are stuck in Windows Mobile screen, unless you can flash the original rom (and I don't think you can...), you have three choices:
1. Send it to www.imei-check.com and they can do a JTAG reflash.
2. Have a repair center replace the motherboard
3. Buy another unit, and keep your for spare parts
drummer10630 said:
HTCSF kEØ(HTCE means corrupted CID, and since you have no KITL, and NO GSM, and are stuck in Windows Mobile screen, unless you can flash the original rom (and I don't think you can...), you have three choices:
1. Send it to www.imei-check.com and they can do a JTAG reflash.
2. Have a repair center replace the motherboard
3. Buy another unit, and keep your for spare parts
Click to expand...
Click to collapse
What about a "task 28" in mtty?
first mistake was not reading directions lol.. you should of had SPLv7 flashed to your phone before you started. there is a whole section in the wiki on bricks you might want to read as well as a whole 60 something page thread on bricks which might help you out. my best guess is send it in for repair or buy another and save the brick for parts. before SPLv1 there where lots of bricks. you also might consider sending your phone to Oli or pof so they can use it for tests if there still doing hermes work
Sorry if i hijack this thread.
but i have the same problem.
corrupted cid, No KITL, stuck @ windows screen.
But the gsm are still okay.
Any solution ??
Cos i have try all the solution here.
Trying upgrade using the orange rom its say device id error
using no id rom update still the same.
using sd card got the same error as batterie
help will be appreciated
thanks
http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
I was in the repaircenter and they will change the complete device. in a few day i will get a new hermes and if i have a little bit luck i have to pay nothing.
if i will have more luck, i will have a mda touch.
when i will have the mda touch, what do i have to look for ???
what can i do with it and what not ?
what "mußt" i do ???
thank you for the help ...
I am sorry for your problems but it still amazes me that people are still flashing there phones without flashing HardSPL first.
I am interested as to why you did not flash HardSPL first, is the information too deeply buried or not easily found?
I didn´t found the information.
i have flashed my hermes about 10 - 15 times with different roms and operationsystems (wm 5, wm 6, radiopatch 1.xx, splash screen, own cooked roms, ..., up and down) and had no problems.
i think the last rom was not for the hermes device.
now i flash first hard spl and then i will try again all the roms ...
without the bricked device i have never heard about mtty, hard-spl, flash by sd card, ... and so on. so i think it was good for me, that i have bricked the device ;-)
learning by doing ...
without a little bit luck i will have in a few weeks two devices, one hermes (mda vario II) and one mda touch ... then i will use the hermes for test and the touch for work ...
thankxxx
i already read those wiki.
the only solution there is
Flash any shipped ROM matching your CID, if such rom is not available wait until your carrier releases it or send it to repair or warranty...
The problem was the device was corrupted cid so i cannot upgrade using the shipped rom (always country id error)
i try to bring to service center.its say it need to be replaced motherboard. and sadly its not cover the guarantee cos not official rom.
drummer10630 said:
http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
Click to expand...
Click to collapse
also for the hard spl question. Usually i hard spl first if i upgrade using non official rom. but its seem my friend doesn't know hardspl and upgrade it directly.
thx.
i´m waiting ...
now i have an new device ... they have changed it ! yippie ... ...
so first i have to flash hard spl !
is there anything else i must have to do ???
batterie said:
now i have an new device ... they have changed it ! yippie ... ...
so first i have to flash hard spl !
is there anything else i must have to do ???
Click to expand...
Click to collapse
Go to MrVanx guides and read up on upgrading and stuff. The guides will let you know what must be done.
I'm sure everyone is getting sick of these posts. This is the reason I have spent about 2 days reading post after post, along with every how-to ever.
I have tried a couple different versions of Hard-SPL.
Olipro 2.10
SPL-2.03
I have problems when trying to run the radio only updates as well as the updates from the Hermes website for ATT. It either gives me error 262 at 0% or 12%.
Here is the printout from mtty
Cmd>info 8
Block 0x0(0) is Reversed block
Block 0x1(1) is Reversed block
Block 0x2(2) is Reversed block
Block 0x3(3) is Reversed block
Block 0x4(4) is Reversed block
Block 0x5(5) is Reversed block
Block 0x6(6) is Reversed block
Block 0x7(7) is Reversed block
Block 0x8(8) is Reversed block
Block 0x9(9) is Reversed block
Block 0xA(10) is Reversed block
Block 0xB(11) is Reversed block
Block 0xC(12) is Reversed block
Partition[0], type=0x20, start=0x2, total=0x18FE
Partition[1], type=0x23, start=0x1900, total=0x1700
Partition[2], type=0x25, start=0x3000, total=0x19E00
Partition[3], type=0x4, start=0x1CE00, total=0x1DA00
CE Total Length(with sector info) = 0x3AA7000
CE CheckSum Length(without sector info) = 0x39C0000
If I try to run task 2a it doesn't tell me anything, just goes back to CMD>
For one, mtty always says CMD> instead of USB>. Is that a problem and how would I fix it. I was assuming it didnt matter.
Can someone tell me exactly what radio I should flash? or the most successful radio that I can flash? I don't care if it is old, I just want to make phone calls. I have even tried to flash the nbh from ubuntu with no success.
Also, is hard-spl V9 any better? I haven't tried it yet. i am going to be doing that right after I post this. I am kind of lost in all of this and have no idea where to go from here. I wish I knew a way to figure out if it is a bad physical radio.
Thanks,
Ray
Sorry to hear it. My Hermes if in the "no GSM" mode to.
My solution, I ended up being getting a Kaiser.
Hope you can find a way to revive yours.
Hi,
It seems that you are not the only one to have a problem with your radio rom. There is a thread here: http://forum.xda-developers.com/showthread.php?t=349461
Could you give a bit more details about what happens before your problem?
- Which radio rom was on your htc before
- Did it stop to work suddenly? or did the problem happen when flashing a new rom?
- Which method did you use for flashing (pc connection or sdcard?)
- Which release of hermes did you have (herm100,200,300?)
- etc...
Thanks
1. My radio was 1.34
2. It just stopped working. Had never been upgraded
3. I tried flashing via pc and I transferred a file to the phone and tried it that way. I may not be doing it correctly though, so maybe I need a point in the right direction for which files to download and flash. Does it have to be from the sd card or can I transfer it to the phone memory.
4. It is a Cingular 8525 HERM100 it says.
Before I put Hard-SPL on it said SPL 1.11 IPL 1.01
Then I started trying to flash several thousand different types of upgrades. Radio rom only, custom RUU, Official HERMES upgrade, etc.
The only progress I made was one time it started flashing and after it failed, the phone restarted and said ATT instead of Cingular.
I have followed steps 4 and 5 on the bricked heremes thread.
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
This is what Im talking about:
USB> password 0000000000000000
USB> set 1e 1
USB> erase a0040000 c80000
USB> erase a0cc0000 c80000
USB> erase a1940000 640000
USB> set 1e 0
After that, I still cant flash anything.
I think it is out of warranty. I dont care to open it up if I have to. Is the radio (that might be corrupted) on a removable board or chip?
I can boot into windows and use it as a PDA, it just has no gsm and no imei
did you solve the problem.the same thing hapeened to me.helpppp
SOLUTION!!!
I had a bricked hermes like everyone else. It had the no GSM message and could not flash anything couldn't even get MTTY to recognize it. I finally got it!!!! I flashed the Hard SPL using the SD Card Method. After I flashed the Official Stock Rom my radio is back. (It did take 2 tries to get the Rom to flash and again I used the SD Card method) I hope you can use this. Just incase you don't know use a 2 GB SD CARD and it MUST BE 2 GB or smaller. put the attached exe file and the .nbh file. Rename the .nbh file to HERMIMG.nbh. Open bootloader and it will start the update after you press start button when prompted. It worked for me and hope it will work for you!!!
Hi,
I got dead Hermes from friend, I menaged to install OS by card update utility but when ever I want to install gsm it stops on 11% or on 0%.
Is there any help?
I have tried all I know but nothing, and this is not the first one i work on.
If anybody can help I would be appy ...
try the following links
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
http://forum.xda-developers.com/showthread.php?t=377389
Thanks,
one thing I did not do is bad block check so I did it and this is what I get:
Cmd>info 8
Block 0x0(0) is Reversed block
Block 0x1(1) is Reversed block
Block 0x2(2) is Reversed block
Block 0x3(3) is Reversed block
Block 0x4(4) is Reversed block
Block 0x5(5) is Reversed block
Block 0x6(6) is Reversed block
Block 0x7(7) is Reversed block
Block 0x8(8) is Reversed block
Block 0x9(9) is Reversed block
Block 0xA(10) is Reversed block
Block 0xB(11) is Reversed block
Block 0xC(12) is Reversed block
Partition[0], type=0x20, start=0x2, total=0x18FE
Partition[1], type=0x23, start=0x1900, total=0x1900
Partition[2], type=0x25, start=0x3200, total=0x1D900
Partition[3], type=0x4, start=0x20B00, total=0x19D00
CE Total Length(with sector info) = 0x4265800
CE CheckSum Length(without sector info) = 0x4160000
It seams it is ok but friend of mine probably tried to flash custom rom without hard sspl optrion and now I can not put any rom up.
Eny other solution...
if you're not sure if it is unlocked unlock first then install hard spl... you can do it through usb or sd card. check wiki for details... check if its hard spl already. go into bootloader and see if the spl is 2.10, 2.30 or 2.60.. if it is then its hard spl.
also check if ipl is 1.04 and not 1.01. if not then re install hard spl version 7. THEN flash os, would try stock rom first as it MAY fix the radio(no promises) . if that doesnt work try flashing a radio only rom and if that doesnt work I'm all out of ideas except to flash an os only rom(no radio) so you can use as a PDA..
personal preference is sd card method for ALL flashing. less chance of unfortunate computer related incident resulting in homicide and bricked hermes...
cheers..
SPL is 2.60 oli
IPL is 1.04
but even on card upgrade it stops on radio rom on 11% and that is it
I have read wiki all over 6 times and tried more or les everithing
any new ideas...
thanks
from what you descibe it sounds like your radio ha been corrupted. once that happens you May(very slim chance) fix it BUT 9 times out of 10 its a permanent brick. You should still be able to flash an os only rom onto it but it is now only a PDA. Keep reading though, you might find something.... chances are though that is not a phone anymore...
thanksfully it is not mine I feel sorry for friend but every school is expensive...
Thanks
strazicic said:
thanksfully it is not mine
Click to expand...
Click to collapse
Animal Mother: Better you than me.
abubasim said:
Animal Mother: Better you than me.
Click to expand...
Click to collapse
Full Metal Jacket reference?
Yep. One of my favorite Kubrick movies. strazicic's remark just reminded me of that scene where they're saying their farewell's to their fallen platoon leader.
just Solved same problem
Hi
i have been dealing with the same problem for 4.5 hours finally with the help of wiki and pof 's posts i managed to unbrick radio.
first of all i tried almost evceryting. i finally succeed by reseting radio sector. i used mtty to gel into hermes and used commands of one of pof's posts for erasing radio sector.
i dont remember the link but google xda for it. then i flashed tweaked version wich is inclueded in unlocker by pof i aborted the operation in unlocking phase then installed hardspl7
i can use my phone now radio version is 1.10 sth but i didnt tried to install newer radio ( too tired :=) )
i hope it is usefull if anything not clear PM me or write here....
PS:Many many thanx to pof...
bartan
strazicic said:
Hi,
I got dead Hermes from friend, I menaged to install OS by card update utility but when ever I want to install gsm it stops on 11% or on 0%.
Is there any help?
I have tried all I know but nothing, and this is not the first one i work on.
If anybody can help I would be appy ...
Click to expand...
Click to collapse
I will try,
Thanks a lot
strazicic said:
I will try,
Thanks a lot
Click to expand...
Click to collapse
plz read the post in WM6 section of hermes ; we have different solutions to this problem maybe one of them may work for you
http://forum.xda-developers.com/showthread.php?t=383194
bartan