I have a g4 which is a bit dead right now.
Basically I have been playing round with trying out different roms. Its CID locked so I have been using shelltool.
On my last flash, something disrupted it and I had to disconnect. No when I turn it on it hangs on the splash screen (o2).
So what do I do now?
I tried downloading the original software from o2 and ried flashing that with the update facility whilst in boot loader mode and it comes up with a 300 error saying i need an updated update thingy.
Can any one suggest anything? Thanks
Will
Flash Wizrd Love
willroy said:
I have a g4 which is a bit dead right now.
Basically I have been playing round with trying out different roms. Its CID locked so I have been using shelltool.
On my last flash, something disrupted it and I had to disconnect. No when I turn it on it hangs on the splash screen (o2).
So what do I do now?
I tried downloading the original software from o2 and ried flashing that with the update facility whilst in boot loader mode and it comes up with a 300 error saying i need an updated update thingy.
Can any one suggest anything? Thanks
Will
Click to expand...
Click to collapse
Check post #79 on this thread
http://forum.xda-developers.com/showthread.php?t=293480&page=36
Sorry but that hasn't helped me. It says
Code:
Greetings,
Now ill be able to use crossbow, thanks alot.
Now i have 1 question- Is it possible to go back to original rom which imate k jam gave me.
Does it change the IPL SPl and GSM.
Thanks Alot Great job.
Be careful
willroy said:
Sorry but that hasn't helped me. It says
Code:
Greetings,
Now ill be able to use crossbow, thanks alot.
Now i have 1 question- Is it possible to go back to original rom which imate k jam gave me.
Does it change the IPL SPl and GSM.
Thanks Alot Great job.
Click to expand...
Click to collapse
IPL and SPL are not touched, I can not answer if you would be able to go back to your original ROM, and agin: when I tried to flash my Cingular "Original" or "official" ROM from the Cingular site my Extended ROM was wiped, so as today I can flash the original ROM but my Ext ROM went to limbo.
Good luck!
The shelltool thread mentions what to do if your phone is stuck on a splash screen. Perhaps you could re-read certain parts of it, in order to get the answer to your post.
this might help you out:
http://forum.xda-developers.com/showthread.php?t=298613
Related
Flashed WMXL 0.20 yesterday. All fine. I stupidly installed a WM2003 program that seems to have edited the graphics driver. Now the thing wont boot past the HTC splash screen. I've tried flashing, same rom, different t-mobile roms etc. No luck, always same error.
What gives?
Installing a program does not usually brick a device.
And if your graphics driver has been modified,I suggest you do a hard reset on your device.
If that is not helping,please provide your SPL and Radio version,also Cid status and so on ,see who can help you here.
Spuddy said:
Flashed WMXL 0.20 yesterday. All fine. I stupidly installed a WM2003 program that seems to have edited the graphics driver. Now the thing wont boot past the HTC splash screen. I've tried flashing, same rom, different t-mobile roms etc. No luck, always same error.
What gives?
Click to expand...
Click to collapse
Sounds like you're flashing & writing before reading. I'm guessing you went straight to the WM6 rom and didn't do any of the SIM or CID unlocking. Read the following threads and you should discover what you need and probably loads more too...
The Hermes Bible - points to all you need to know
http://wiki.xda-developers.com/index.php?pagename=HTC_Hermes
Common upgrade problems (including yours)
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
Good luck in your discoveries
Thanks for your advice. I have managed to flash a hungarian T-Mobile ROM to my device and am now going to make is supercid so I can put WM6 back on. Thanks again.
Spuddy said:
Thanks for your advice. I have managed to flash a hungarian T-Mobile ROM to my device and am now going to make is supercid so I can put WM6 back on. Thanks again.
Click to expand...
Click to collapse
Congrats and have fun flashing - it's addictive.
I'd suggest that you read and try Olipro's Hard-SPL before you go any further. This appears to be the answer to many of our prayers because you should be able to recover a bad radio flash. (I'm guessing that the 1.04 version will become most popular)
Hard-SPL, Or How to Not Brick Your PDA Ever Again
http://forum.xda-developers.com/showthread.php?t=296722
Spuddy said:
. . . a WM2003 program that seems to have edited the graphics driver . . .
Click to expand...
Click to collapse
What program was that, if you don't mind my asking?
abubasim said:
What program was that, if you don't mind my asking?
Click to expand...
Click to collapse
DotPocket.
http://www.dotpocket.com/pocket-pc-software.html
Ok, I give up. I've been searching all night and I cannot find an answer - all the answers that I have found seem to have driven me and my device further to a state that is unrecoverable.
First I couldnt update the rom at all because it crashed mid way, then I finally did get an OS up and running, yet with no radio - no imei or phone functions. I couldnt update radio rom, and I couldnt revert to the original. I now have just a boot loader, that I cannot install anything on to, at all.
"
HERM300
IPL-1.01
HERM300 MFG
SPL-1.01"
I know I'm running the wrong boot loader now, but it was in effort of persuing being able to update the radio rom. I'm following the instructions to change it and at "task 32" Im getting "FF"
Please. Someone help. I cannot be accused of searching first hand as I've been sat here since 7pm trying to sort this, its now 3:44.
Cheers.
you didnt change to hardspl boot loader before u tried to update it?
mien916 said:
you didnt change to hardspl boot loader before u tried to update it?
Click to expand...
Click to collapse
man, OP, please tell us you did...
have you tried reading here?
and here?
yes. and yes. Thanks for the quick replies - looks like im still up with it.
Bad times.. " you didnt change to hardspl boot loader before u tried to update it?" - this I dont understand. I've been following my nose all night. I've updated roms before, but i've never had any issues, certainly not like this.
Good times.. I've got it to boot. and I'm running WM6 "Pro Black" on the thing as we speak. so its not that dead..
I still have no radio version, nor imei, and spl/ipl is still 1.01. I'm trying to update radio rom, but it hangs at 0%.
i take it youve ruled out a bad usb connection? have you considered trying the SD CARD method of upgrading your rom?
thats all but ruled out, as i havent got an sd reader attached.
im making some headway, got the SPL at 1.10.Oli - still cant install radio rom though!
interesting. the shipped tmobile rom is now working...
I say working, its getting up to 13%. which is more than the 0 i was getting earlier.
Ok. So we're up to normal bootloader
IPL 1.04
SPL 2.10
No radio rom will install though. at all. error 262.
I have the same probleem with my t mobile vario 2. I can only upgrade OS ONLY rom, when I try to flash radio it freeze 0% error 262. I've tried evrything from wiki but nothing has worked jet. I hoop sameone can help us.. thanks
jacky651 said:
I have the same probleem with my t mobile vario 2. I can only upgrade OS ONLY rom, when I try to flash radio it freeze 0% error 262. I've tried evrything from wiki but nothing has worked jet. I hoop sameone can help us.. thanks
Click to expand...
Click to collapse
have you considered SIM/CID unlocking your phone? just a thought. not a definite solution. proceed with the latter (CID) AT YOUR RISK as ive heard changing CID to SUPER CID will make your device SUPER CID for eternity (?) and may void any warranty that you have..
bapski said:
have you considered SIM/CID unlocking your phone? just a thought. not a definite solution. proceed with the latter (CID) AT YOUR RISK as ive heard changing CID to SUPER CID will make your device SUPER CID for eternity (?) and may void any warranty that you have..
Click to expand...
Click to collapse
i 've unlock my phone couple month ago. it super CID i checked with 'mtty' info 2. i can flash everything except radio
Well I being stupid person that I was loaded Faria's rom without unlocking my G4 it got to 99% and errored saying update error and such. So i did some research finding out that I had to unlock first, now after reaidng some tutorials I see things about uploading the EnableRapi to my 8125 but problem is when I turn it on it only has the rainbow colors I can't get in to the phone and I can't use it..
Could anyone please help me and guide me or paste me a thread on how I can fix this. I've been researching for hours and haven't gotten anywhere. If anyone can please help me itll be greatly appreciated.
Thanks
All you have to do is put your phone in bootloader mode then flash wizard love or the rom that your device was shipped with.
You havent told us what wm5 rom your device originally had on it so we cant help you there but Wizard Love can be found here and here.
peter petrelli said:
All you have to do is put your phone in bootloader mode then flash wizard love or the rom that your device was shipped with.
You havent told us what wm5 rom your device originally had on it so we cant help you there but Wizard Love can be found here and here.
Click to expand...
Click to collapse
i've installed farias o1st wm6 rom on my g4 device using the shelltoll method..
i wanted 2 try nother wm6 rom
do i have 2 go thru the entire unlock process again or just use the shell tool with the new rom
ok
u hav 2 go thru the unlocking CID process again & everytime u want 2 reflash
Cingular 8125 G4
All seems to be working back to normal question though using the shelltools it doesn't display all the information about the phone when I press Get Info, i have a 2.x.0001 but when I press get info it wont show the info on CID or the option below it, but itll allow me to Extract OS, is that okay? or do if I flash it, it won't work?
aurfawce said:
All seems to be working back to normal question though using the shelltools it doesn't display all the information about the phone when I press Get Info, i have a 2.x.0001 but when I press get info it wont show the info on CID or the option below it, but itll allow me to Extract OS, is that okay? or do if I flash it, it won't work?
Click to expand...
Click to collapse
Unless the person who converted the 80040000-OS.nb to nk.nbf filled in those fields then they will be blank. Dont worry about these details. Flash away.
Good Luck
G4 help
so i tried flashing it I thought it was successful I did the hard reset after I ran the ShellTools. Was I supposed to do anything after the hardreset? Because I though then maybe I can go on to trying Faria's stuff but when I did got to 99% and 302 error occured so now im flashing back to old ROM, any hints? tips? or programs to make the G4 unlocking easier? any or maybe any roms out there you know of that won't mess with the SPL/IPL that I can just load the rom and use it?
Thanks
aurfawce said:
so i tried flashing it I thought it was successful I did the hard reset after I ran the ShellTools. Was I supposed to do anything after the hardreset? Because I though then maybe I can go on to trying Faria's stuff but when I did got to 99% and 302 error occured so now im flashing back to old ROM, any hints? tips? or programs to make the G4 unlocking easier? any or maybe any roms out there you know of that won't mess with the SPL/IPL that I can just load the rom and use it?
Thanks
Click to expand...
Click to collapse
So you tried to flash Faria's rom to a CID locked G4 then when that didnt work you used shelltool. Following this you tried to flash Faria's rom to your still CID locked G4 and it didnt work again?
I'm a bit confused so I'll start at the beginning again. If you do in fact own a G4 CID locked device then the only way that you can upgrade your OS is to use shelltool, unless you want to pay imei-check to unlock it. Using the RUU method to update a CID locked G4 will produce an error and not finish flashing or it will complete the flashing process but your OS will not have changed.
Shelltool doesnt unlock your device, it will still be CID locked after shelltool completes. Shelltool only updates OS so the chance of bricking your device is minimal. Hope this helps.
I have an new titan, and it has spl-1.20.olipro bootloader.. I am trying to reflash but it reboots at 11%. I can't get any roms to fully flash.. It's stuck on the HTC black screen and say's not radio..
I need help.. how can i fix this cux i can't get any roms to flash... cooked or official
use the boot loader in the guide bellow
follow this guide and start all over
it was stuck in 1.2 olpro. I cant get any rom to flash or update to 2.40... I tried to flash radio 3.27.. that went 100% but now the phone won't even turn on
do you get a charge light when you plug it in to the wall? if so make sure its not dead, ya never know.. lol
no i don't get anything.. no charge light or anything.. it dead
yeah sounds like a brickk... sorry =\
take it in and try to get another one
jmann76 said:
it was stuck in 1.2 olpro. I cant get any rom to flash or update to 2.40... I tried to flash radio 3.27.. that went 100% but now the phone won't even turn on
Click to expand...
Click to collapse
***EDIT***
Dang, I just read your post about your light not even turning on. Did you try soft resetting it? I know that sounds dumb, but had to ask. Did you try taking the battery out for a bit? Try holding the Power button and the Camera button down on the right side of the phone and push your stylus into the soft reset hole. That's the way to put it into bootloader mode. If you've got the phone plugged in even (try it without the battery too) and you still don't get anything, then I'd say try to get it replaced if you can. That's never a good feeling. I've had a couple of HTC devices now, and have been there a couple of times where you think your phone is dead, but it ends up not being that way. I hope this situation goes the same way for you.
*********************************
3.27 requires 2.40 and is also outdated.
You could try the Titan Relocker to put an older bootloader version on it, and then flash an official rom that supports GPS, which will update you to the Carrier's ROM and Radio. At that point, you can try to unlock and flash to 2.40.
Once you have 2.40 installed, you can then put on a 3.xx radio (3.39.10 is recommended right now) and flash to a custom ROM, such as DCD's newly released 3.1.6 ROM. I think it runs really well, and I flash mine to different roms way more than I'd like to admit. I think I'm going to stay with this one for a while.
Once you get the 2.40 bootloader, I'd start using the SD Card flashing method for your ROMs exclusively. It works really well, and the good thing is that you can have other stuff on the card, so you can use a small card by itself only for flashing, with folders for different ROMs and Radios, or you could use one big one, and then just change the required file every time you wanted to flash.
I haven't included links to everything because that would take a while, but you should be able to find everything I've mentioned by using the search function, or if you can't seem to find what you're looking for here, you can try ppcgeeks.com too, it's another great resource for our phones.
Good luck!
-kmart
P.S. Don't worry too much about your phone, these titans are actually quite hard to brick. As long as you can get to the bootloader, you should have a good chance to get everything working properly again.
jmann76 said:
I have an new titan, and it has spl-1.20.olipro bootloader.. I am trying to reflash but it reboots at 11%. I can't get any roms to fully flash.. It's stuck on the HTC black screen and say's not radio..
I need help.. how can i fix this cux i can't get any roms to flash... cooked or official
Click to expand...
Click to collapse
You are fine. Though as your Titan is already unlocked and had an older third-party ROM installed, it ain't so "new" . Your problem is covered in the Wiki:
II. Install the correct bootloader
Hit Power-Camera-Reset to check what version of bootloader you have installed.
At the tri-colour bootscreen you will see the version number installed.
if it is 1.04 or 1.06 then you must unlock your phone and upgrade to 2.40. Olipro 1.20 is not necessary at all when using newer ROMs/Radios.
if it is 1.20 then you have the pre-GPS ROM bootloader and must first flash to one of the older ROMs and associated radio to boot into WM, get an ActiveSync connection and then upgrade to 2.40.
if it is 2.40 then you have the correct bootloader and are ready to move on to the Radio Upgrade in Section III.
michaelm91 said:
use the boot loader in the guide bellow
Click to expand...
Click to collapse
Guys, the info first presented in that thread is out of date and not maintained. Please let it disappear and first direct people in help to the Wiki.
jmann76 said:
...that went 100% but now the phone won't even turn on
Click to expand...
Click to collapse
Oops, I just read that too... Remove the battery or try another battery yet? Other than that...
how did things finally turn out jmann?
Dear all,
I am facing a problem here.
Had a hardware problem with the built in microphone and had to revert back to stock rom/splash screen/Original SPL in that order.
Had no problems reverting the ROM and the original screen back (just a couple of flashes), BUT when I tried to revert back the stock SPL here http://forum.xda-developers.com/attachment.php?attachmentid=110582&d=1220406410
I renamed the file to RAPHIMG.nbh, copied it to the root of the SD Card and entered bootloader mode and this is what it displays:
RAPH100
SPL-1.90.0000 (Which means a successful flash)
!!! AND THEN THIS !!!
"Upgrade ROM code error"
"Please try again"
This message is located in the last part of the green stripe in the tri color screen (bootloader)
It is then followed by the grey screen automatically which you are supposed to press volume key to start a flash process BUT it just HANGS at Loading...
unabling you to flash anything.
It's actually a friend's phone too so I guess you understand how hard it is....
Any help is appreciated
Thanks in advance
Possible image might be corrupt on sd card, grey screen is shown when it's trying to read sd, have you tried with sd removed? if you get to 2nd tricolor screen with sd removed i would use usb flash to restore it to working order..
Da_G said:
Possible image might be corrupt on sd card, grey screen is shown when it's trying to read sd, have you tried with sd removed? if you get to 2nd tricolor screen with sd removed i would use usb flash to restore it to working order..
Click to expand...
Click to collapse
Removed the SD and it stays at the tricolor screen with the spl version as mentioned in 1st post.
Also, displaying the Upgrade ROM code error, please try again message
The mode is currently serial
What can I do from here?
fireblade63 said:
Dear all,
I am facing a problem here.
Had a hardware problem with the built in microphone and had to revert back to stock rom/splash screen/Original SPL in that order.
Had no problems reverting the ROM and the original screen back (just a couple of flashes), BUT when I tried to revert back the stock SPL here http://forum.xda-developers.com/attachment.php?attachmentid=110582&d=1220406410
I renamed the file to RAPHIMG.nbh, copied it to the root of the SD Card and entered bootloader mode and this is what it displays:
RAPH100
SPL-1.90.0000 (Which means a successful flash)
!!! AND THEN THIS !!!
"Upgrade ROM code error"
"Please try again"
This message is located in the last part of the green stripe in the tri color screen (bootloader)
It is then followed by the grey screen automatically which you are supposed to press volume key to start a flash process BUT it just HANGS at Loading...
unabling you to flash anything.
It's actually a friend's phone too so I guess you understand how hard it is....
Any help is appreciated
Thanks in advance
Click to expand...
Click to collapse
You cannot flash an SPL from the bootloader. You need to use SSPL. The directions can be found in the HardSPL thread.
NotATreoFan said:
You cannot flash an SPL from the bootloader. You need to use SSPL. The directions can be found in the HardSPL thread.
Click to expand...
Click to collapse
Hey man, thx for stopping by..
If I understand correctly, SSPL runs through the device which is stuck at bootloader currently... or am I hopefully wrong??
If you're at the tricolor screen and it reads serial, that should be fine.. plug in usb and it should switch to usb.. then flash a stock carrier rom through usb.. that should get you up and running and you can then run sspl and flash your spl
Da_G said:
If you're at the tricolor screen and it reads serial, that should be fine.. plug in usb and it should switch to usb.. then flash a stock carrier rom through usb.. that should get you up and running and you can then run sspl and flash your spl
Click to expand...
Click to collapse
Keep in mind im currently on stock SPL, do u think flashing the stock ROM is ok?
That's exactly why i suggested stock ROM, stock SPL will only accept stock ROM's (it will overwrite the spl too so make sure the stock rom you are using is the right one)
dude....i hate to say this...butyou might be s.o.l. at this point. i did the same to my fuze not too long ago... tryingto flash anything to the phone just locks it up.i was lucky enough to bs my way through an att guy to get me a new one (was still under the 30 day warranty).
Da_G said:
That's exactly why i suggested stock ROM, stock SPL will only accept stock ROM's (it will overwrite the spl too so make sure the stock rom you are using is the right one)
Click to expand...
Click to collapse
That's wt Im trying now, tried to flash 2 ROMs already and stops at 2% saying Invalid Vendor ID
I gess I'm using wrong shipped roms till now
fireblade63 said:
That's wt Im trying now, tried to flash 2 ROMs already and stops at 2% saying Invalid Vendor ID
I gess I'm using wrong shipped roms till now
Click to expand...
Click to collapse
I had the same problem as you and could not flash any rom, Always get Invalid vendor ID.
You need the right Stock Rom to flash and in my case in the middleeast, the Stock Rom is so far only available in at HTC.
I had to take the phone to HTC Service Center and they flashed the correct Stock Rom and charged me as they did it out of warranty.
Regards
fireblade63 said:
That's wt Im trying now, tried to flash 2 ROMs already and stops at 2% saying Invalid Vendor ID
I gess I'm using wrong shipped roms till now
Click to expand...
Click to collapse
Sorry about my last post... I misread your issue.
If you flashed the stock 1.90 SPL from the HardSPL thread, then you will need to ask Olipro (or cmonex) which WWE ROM it originated from. That ROM is the ONLY one your phone will accept.
The steps in reverting SPL for warranty / return state to always do the ROM first so that you do not run into this problem. I had the same issue when I was testing a US 3G Diamond I bought from Best Buy (to become acclimated to TF3D prior to the Fuze's release). I restored the SPL first, and then couldn't get Dutty's ROM off the phone, because I could not locate a downloadable version of the WWE ROM that phone came with. [Luckily, Best Buy Mobile's employees in KOP, PA aren't too clever, and I was able to convince them that the phone came that way. ]
NotATreoFan said:
Sorry about my last post... I misread your issue.
If you flashed the stock 1.90 SPL from the HardSPL thread, then you will need to ask Olipro (or cmonex) which WWE ROM it originated from. That ROM is the ONLY one your phone will accept.
The steps in reverting SPL for warranty / return state to always do the ROM first so that you do not run into this problem. I had the same issue when I was testing a US 3G Diamond I bought from Best Buy (to become acclimated to TF3D prior to the Fuze's release). I restored the SPL first, and then couldn't get Dutty's ROM off the phone, because I could not locate a downloadable version of the WWE ROM that phone came with. [Luckily, Best Buy Mobile's employees in KOP, PA aren't too clever, and I was able to convince them that the phone came that way. ]
Click to expand...
Click to collapse
Hmm, then I need to know from which ROM the SPL originated and then flash it.
Thing is, some of the shipped roms available at wiki are just nbh files..
I tried flashing with the wrapper exe and the RaphaelCustomRUU.exe and still all roms I've downloaded don't seem to work.
It's a RAPH100 untied to a network.
fireblade63 said:
Hmm, then I need to know from which ROM the SPL originated and then flash it.
Thing is, some of the shipped roms available at wiki are just nbh files..
I tried flashing with the wrapper exe and the RaphaelCustomRUU.exe and still all roms I've downloaded don't seem to work.
It's a RAPH100 untied to a network.
Click to expand...
Click to collapse
Post in the HardSPL thread asking which ROM the SPL originated from. Once you know that, you can download the appropriate ROM from the Wiki.
NotATreoFan said:
Sorry about my last post... I misread your issue.
If you flashed the stock 1.90 SPL from the HardSPL thread, then you will need to ask Olipro (or cmonex) which WWE ROM it originated from. That ROM is the ONLY one your phone will accept.
The steps in reverting SPL for warranty / return state to always do the ROM first so that you do not run into this problem. I had the same issue when I was testing a US 3G Diamond I bought from Best Buy (to become acclimated to TF3D prior to the Fuze's release). I restored the SPL first, and then couldn't get Dutty's ROM off the phone, because I could not locate a downloadable version of the WWE ROM that phone came with. [Luckily, Best Buy Mobile's employees in KOP, PA aren't too clever, and I was able to convince them that the phone came that way. ]
Click to expand...
Click to collapse
SPL has nothing to do with the Invalid Vendor ID Error, It is the CID. In another word you can flash SPL 1.95 and still can not flash the AT Rom 1.95.502.5 because the CID is different.
Regards
ViperBJK's QMAT features GoldCard generator for current HTC devices that can force RUU to bypass CID check.
Do you know what is the CID of your device?
shafez said:
SPL has nothing to do with the Invalid Vendor ID Error, It is the CID. In another word you can flash SPL 1.95 and still can not flash the AT Rom 1.95.502.5 because the CID is different.
Regards
Click to expand...
Click to collapse
The CID is determind by the SPL.
Look up the error code posted... everything points to HardSPL. Back in my Wizard days, HardSPL did not exist, and we just did a CID unlocking. This is not the case with newer devices.
All ROMs are not created equal. Each WWE ROM checks for specific information within the SPL, and if it doesn't find what it's expecting, fail...
stepw said:
ViperBJK's QMAT features GoldCard generator for current HTC devices that can force RUU to bypass CID check.
Do you know what is the CID of your device?
Click to expand...
Click to collapse
I'm not sure
Where can I know that?
@NotATreoFan && Shafez,
I remember from TyTNII day when Shafez suggested extracting 3.29 and 28 SPLs from the newer shipped 6.1's for a better responsive device.
We could extract and build with htc rom tool if I remember the name of the tool correctly.
Do we have a tool as such compatible with TP? (agreeing with NotATreoFan here)
@Shafez,
Since you think it is not SPL and it is a CID issue, what can I do about it?
Sending it to SVC for repair out of warranty is an option but I'd like to leave it as my last.
Did they provide the ROM or they flashed it for you?
Were u able to make raw files out of it for future use or any1 else has it?
Thx guys and keep the help coming
fireblade63 said:
@NotATreoFan && Shafez,
I remember from TyTNII day when Shafez suggested extracting 3.29 and 28 SPLs from the newer shipped 6.1's for a better responsive device.
We could extract and build with htc rom tool if I remember the name of the tool correctly.
Do we have a tool as such compatible with TP? (agreeing with NotATreoFan here)
@Shafez,
Since you think it is not SPL and it is a CID issue, what can I do about it?
Sending it to SVC for repair out of warranty is an option but I'd like to leave it as my last.
Did they provide the ROM or they flashed it for you?
Were u able to make raw files out of it for future use or any1 else has it?
Thx guys and keep the help coming
Click to expand...
Click to collapse
Since you cannot get past the bootloader, your only option is to find the WWE ROM that matches the SPL you flashed. Even though the HTC ROM Tool "signs" the NBH file, it still won't fool the stock bootloader... if it did, we wouldn't need HardSPL.