I tried to do a ROM Upgrade but something went wrong and now the screen on my XDA II just shows the words Serial and v1.06. When I did a hard reset the screen still shows the same thing. When I connect the device using the cradle the word Serial changed to USB, but it didn't seem to connect to the PC. The Activesync was not activated also. When I tried to run the ROM Upgrade again, it shows ERROR 100: MODEL ID ERROR. I tried to run HimaUpgradeUT_noID.exe, it shows Error 103: ROM IMAGE FILE NOT FOUND. Can anyone please help me get my device working again? Thank you in advance.
Wrong ID
a few days ago i had the same problem with my HTC Blue Angel (also known as
qtek 9090)
temporaly youre PDA shows the bootloaderscreen. On top it shows youre kind of connection, on the bottom you can find the revision of this piece of software.
try this tool to reanimate youre pda.
http://rapidshare.com/files/36498840/MaUpgradeUt_noID.rar runterladen.
extract this file into the dir, where you have copied the original ROM-Image from youre developer, put youre PDA into cradle and check, if the status of this connection is changed in USB. Everything o.k? Right now: doubleklick on MAUpgradeUT_NoID and drink a coffee. it takes about 10 Minutes and after this youre pda runs as well. dont forget to copy youre original ROM-Image with the original Installer after finishing this procedure to avoid any errors.
Well, i hope this tutor will help you. i´m interested for.
Wrong ID
a few days ago i had the same problem with my HTC Blue Angel (also known as
qtek 9090)
temporaly youre PDA shows the bootloaderscreen. On top it shows youre kind of connection, on the bottom you can find the revision of this piece of software.
try this tool to reanimate youre pda.
http://rapidshare.com/files/36498840/MaUpgradeUt_noID.rar runterladen.
extract this file into the dir, where you have copied the original ROM-Image from youre developer, put youre PDA into cradle and check, if the status of this connection is changed in USB. Everything o.k? Right now: doubleklick on MAUpgradeUT_NoID and drink a coffee. it takes about 10 Minutes and after this youre pda runs as well. dont forget to copy youre original ROM-Image with the original Installer after finishing this procedure to avoid any errors.
Well, i hope this tutor will help you. i´m interested for.
[email protected] youre own risk.
Dead XDA II
Hi Guys, I'm new to all this because my XDA has never failed me, until now. I too tried to upgrade the ROM, realising too late that the upgrade from a UK site was not meast for the Asian zone.
Anyway, I tried downloading the following link:
http://rapidshare.com/files/36498840...adeUt_noID.rar runterladen.
When I tried to lanch the file it tells me that RUU.dll is missing.
Is there a link that works or is there a fix for this? As I said, I'm new to this therefore need step by step instruction.
Hope someone can assist, I'm lost without my XDA II.
Thank you
Ben
cannot download from the link
hello
I have a black screen on my qtek 2020i (XDA2i) after upgrading the ROM, and I saw that the solution you are providing works good, but I cannot download the fix using the link
please advice
http://rapidshare.com/files/36498840/MaUpgradeUt_noID.rar
XDAII Dead
hi,
ive put my MDA into the cradle and get the Serial screen to change to a USB screen. ive downloaded the file and put it with the rom upgrade that i got frm T-Mobile. when i run the program on my computer i keep gettin "Connection Error" screen. what should i do.
pleas advise.
m1000 dead sad
i regreat to say i did try for update my spv m1000 today but my got died now when i tried i did conntect my ppc with ppc via bluetooth actvesync when i run HimaUpgradeUt.exe then a window open and shows mgs wait 30 minunt but after even 1 minunt got error also my phone got stop like dead and screen shows on top serial and on bottom it shows v1.3 i realy .sad. becouse now i cant reeboot also even ui have not data cable any body help me plz what i do now ?
thanks for my help
really want to say thanks who helpd me i upgraded now my spv m1000 my self without any problem becouse i brought data cable of i mate and its workin fine with my spv m1000 yahooooooooo xda roken
usman_hussain1987 said:
hi,
ive put my MDA into the cradle and get the Serial screen to change to a USB screen. ive downloaded the file and put it with the rom upgrade that i got frm T-Mobile. when i run the program on my computer i keep gettin "Connection Error" screen. what should i do.
pleas advise.
Click to expand...
Click to collapse
Hi Usman,
What OS of windows PC do you use? it can't work with windows vista. Try to downloads new version of active sync then try it again. The upgrade is specify, can't work in any kind of devices
Related
Have I fried my XDA 2?
I've had this thing 1 hour and I was running the latest rom upgrade from O2. While it was checking the rom in my XDA2 it came back saying "Error 120: Country ID Error". Now the thing is stuck in a serial bootloader 1.03 mode and grey screen.
I'd not made ANY changes to config of the XDA before trying to upgrade it.
Any ideas?
Don't lose hope mate! I had a very similar problem, with the same result, only my screen said "Serial v1.01" Black text on grey background, no backlight. When I placed it into the USB Cradle it changed to "USB v1.01". It would do this even after I took the battery out for 20 minutes, the moment I relaced the battery, without even pressing the power button. I believe this is correct operation for the XDA II when it's "between ROMs" so to speak, perhaps someone in authority will confirm this?
Anyway, after rebooting the XDA II and the PC, and re running the upgrade sequence about 10 times it worked, and I now have a perfectly functional XDA II. Made me sweat, and swear, for a few hours though, I can tell you.
Keep trying and good luck. Sorry I can't help more!
Andy
I have the same problem... still not working eventhough tried many many times..
It wont even go to bootloader mode.. (pressing power, navigation and reset button)
I come up with serial on top but when i plug-in to a usb cradle it turns to USB and v.1 06 at bottom..
I also tried with different roms.. (QTEK and MDAII) upgrade utility but it only comes up with a window "checking the information on your pocket pc.. .please wait" then the xdaII screen went blank (like no power) and the utility does nothing else..
can someone help? or have i lost the xda II totally?
Hi,
Same problem for me!
Please let me know how it can be solved.
:evil:
I am in the same deep **** ma self! please any1 who knows please help us!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Sent back to the place where you buy your XDA... :? that's the only way...
Sent back to the place where you buy your XDA... that's the only way...
Click to expand...
Click to collapse
ITS NOT THE ONLY WAY.. because what we did is actually out of warranty.. we are trying to be different with others.. besides if you can't put a good answer you better not reply at all.
alimx said:
Sent back to the place where you buy your XDA... that's the only way...
Click to expand...
Click to collapse
besides if you can't put a good answer you better not reply at all.
Click to expand...
Click to collapse
alimx, You could be more polite replying to him, he was giving you a suggestion, why you become RUDE!!
well, If i have an answer or a solution to your problem then I prefer NOT to give it to you, jerk!!
:evil: :evil: :evil:
alimx,
when it says "Serial" and "v1.06" then changes to "USB" when you place in the cradle, IT IS in bootloader mode.
I had this same problem with a recent i-mate I bought for my boss. It won't let you downgrade or switch to any other ROM besides the 1.66 i-mate ROM.
1. Open Activsync without the unit in the cradle.
2. Go to Activsync and uncheck the box where it says "Allow USB Connection with this Computer" (seems strange I know but it works)
3. Put the i-mate in the cradle. It should say "USB" and "v1.06" at the bottom.
4. Download and run the i-mate ROM version 1.66 from clubimate website.
5. Allow it a few minutes and it should finally come up with the screen about converting blah blah to blah blah ROM.
For some reasons, the new i-mates coming out that have the 1.66 ROM will not allow a downgrade to ANY OTHER ROM. Which I think is BS.
For the guy having trouble with 1.10 Radio version. My suggestion is to re-run the 1.66 ROM (I think it's your only option at this point until a new ROM is issued from i-mate). It may fix things. My 1.10 radio version seemed better the second time I loaded the ROM (I know it shouldn't make a difference but it seemed to).[/list]
Hi
When i tried the upgrade program version 1.0 from orange 166 DK my XDAII started at least to show error codes when upgrading.
Before it only become black
My unit was á new QTEK 2020 with french system 1.66, boatloder 1.06 maybe newer units needs the latest himalya upgrade software.
I will keep trying
Dear all.
I had the very same problem couple nights ago. All I did was soft and hard reset, all of which didn't help. But just before I lost my hope, I re-cradled my XDA II, at that time my xda's screen was still black and displayed "Serial", then I chose different upgrade version and installed it from my PC and everything turned out fine.
HTH Cheers,
I am having the same trouble
I am trying all these suggestions, but with no luck so far! (my screen displays v1:01 When I try and install anything on it, my pc can't detect the device
Any more advice?
HI
I found this
http://www.sourceo2.com/O2_Developers/Devices/O2_Xda_II/XdaIIRom.htm
I downloaded the xdaII launch rom, and it is working!! My screen tells me it is upgrading!!
Hope this helps!
Have fun
pw
my appology
My appologise goes to nakamichi... and alexlloyd54... sorry, i didn't mean rude.
I upgraded a TMobile XDA1 got the main ROM upgrade then went and tried to upgrade the radio stack. As I see from the many posts a bad thing to do. But this leaves me with a broken unit. The radio was T310. I can not see how I can solve this problem. I have an SD card, I have a friends German unit with an ENG Rom and the orignal radio which I will leave alone. How can I fix mine?
Thanks
GSM error on Bootload 1.50
Looks pretty much the same as my problem. By pressing the joystick after the error message, I get one step further, but no contact or upload of the ROM. I hope some wise person can supply an answer, :roll:
I have the same problem...
XDA O2 on Wallaby BootLoader v5.15 I see the error : "GSM ERROR"
my pda don´t start good I only see the rom version (3.17.03) and a blue wallpaper of O2..
I already update my rom but it don´t work yet !
Where can I find a GSM rom update? I'm from Portugal
What more can I do ?
Please, help me !
thanks
Joao Afonso, from Portugal
GSM Error
I have tried a number of solutions. None seem to work. If someone has the GSM rom and a solution to upload it let us know. I have tried coping a new radio version to the windows dir on the PPC, this fails. I have removed the back cover and battery again this does not work. The only alternative is to send it back for repair (expensive) or get a new one. I have looked at the solutions in the forum area and on the web but can not find an answer. The unit is an old TMobile (GERMAN) Xda. Upgraded the OS OK then messed up the radio. So as I say let me know if someone has a proven solution. Thanks.
How to fix GSM Error Problem ....
Download the XDA-Developers ROM Version 1.1.
Install the ROM on your Device via SD-Card and bootloader.
The phone should start up and give you the screen allignment and the whole menu!
Download an Upgrade for your device. This depends ont the model you are using. Check the sticker at the back of your device.
If it is a PW10A-Model download RSU Version 4.16.
If it is a PW10B-Model download RSU Version 6.24.20.
Extract the downloaded ZIP-File and copy all files to the /Windows directory of your device.
Copy the RSUpgrade.exe additional to the /windows/startup directory.
Make an soft reset of your device.
Maybe the upgrade will stop again at 1%, this may occur when you have an empty battery.
Place your device in the cradle. Run Active Sync on your device.
The RSU Upgrade will run in the background.
Wait for about 10 Minutes. The upgrade should complete in the background....
Afterwards all should work again...
Good luck....
Click to expand...
Click to collapse
GSM Error
Many thanks for the information. I have tried this but to sorry to say this does not work for me. I can get the RSUgrade.exe to load on the PDA, it stops at 1% and then hangs. The XDA was a TMobile GER unit with 32Mb. I have two units the same, I attempted to upgrade the radio on one and it failed at 10% rebooted and hung with GSM error. Since then I am at a loss as to the next step apart from throwing it in the bin.
same here
it always promt me failed flash device restart press ok. wat the hell is dis . does my gsm rom id basted?day i cant upgrde it tnx
Same problem..
.. and no solution for the GSM Error. There is no possibility to get a connect (O2 germany) and the RSU-Utility stops after 1% - always.
Please help!
Have you tried leaving it for 24 hours with the 1% on screen?
Flash failed
The problem is that there is a message "Flash failed - press ok to restart."
No possibility to leave the program..
same w u
ya i wish someone can find any sol 4 our prob. same problem w u guys.
Dear friends
I was tring to upgrade my iMate Pocket PC also know as Himalaya with windows2003 SE , while upgrading I faced problems, the upgarde failed and now I am just getting no display and OS too. The only message displayed is
Serial
v1.03
nothing is working please help
bye with regrads,
your unit is still okay; even better that the usb version is showing on the screen. it's simply stuck on bootloader mode. what kind of problems did you encounter resulting in the failed upgrade?
one suggestion i can give before you downgrade is to try and proceed with the upgrade to se. put your unit back on the cradle but don't expect activesync to "recognize" the device. just put it back on the cradle and rerun the upgrade to se.
same thing happened when i upgraded but to wm2005. the screen showed error and the only thing on the screen was the usb version. i simply cradled back the unit and ran the upgrade. worked.
cheers
Hi
Thanks a lot, i tired those steps before and even now I did but its not upgarding I am gettig following error as show i the attachment. Please let me know what to do
thanks a lot
yas
oh, it appears that you have the "wrong country" id issue. i'm not entirely sure as to how to avoid this but i believe it has something to do with the correct rom version (guys, correct me if i'm wrong). where did you get the rom you used for upgrading to se? downgrading might be the only trick if there is no rom for saudi-based users...but if any chaps presently living there and were successful in upgrading their units perhaps you could share the rom version/s you used?
cheers
yasirirfan said:
Hi
Thanks a lot, i tired those steps before and even now I did but its not upgarding I am gettig following error as show i the attachment. Please let me know what to do
thanks a lot
yas
Click to expand...
Click to collapse
To overcome the Country ID Error, first you need to install this tool...
ftp://xda:[email protected]/Tools/ER2003Edit_1_4_26.zip
Open the ROM file you want to upgrade, then change the appropriate 'Operator ID' code, after this click 'Save ROM image'.
Upgrade ur device. You will no longer face the error message.
Hi,
I did the popular mistake, tried to unlock with Universal Unlocker , thinking that this is the staff to unlock all the HTC phones.
Ok. What I have now:
NO GSM - we know that
Tried to install radio roms from here, nothing. I got the information about "Checking the information...." and it is hanging like this.
I made reser and HARD RESET aswell.
I tried to install a lot. Nothing helped.
I had radio ver. 1.05.... I remember that. I have my phone from T-Mobile from UK. I had everything nice, now I have four stripes - RED GREEN BLUE and WHITE and ther is written:
HERM300
IPL-1.01
HERM300
SPL-1.04
Can anybody help me ? I tried to download mtty.exe and put all the commands (not PASTE and it still not working.
Now is 6am in Lisbon. I was sitting all that night and I am finishing writting this post.
Help if you can, regards.
Ben
Have a look on this topic http://forum.xda-developers.com/showthread.php?t=280733
It did not help. Where I can get this Qtek rom ? Is that OK for my device ? I have VARIO II from T-Mobile.
I woul like to try instal this - DUMPED English ROM from TMobile Vario II from here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_DumpedRoms
but i dont now how. There are 3 .raw files, how to put them to my phone ?
That solution didnt help: http://forum.xda-developers.com/showthread.php?t=280733
What else I can do ? I was trying with QTEK rom and a got white screen on the phone and 0% on the computer. It was hanging. I tried 5 times. Then I tried to install the Radio Rom from here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms
I choosed all of them. Nothing. All of them are hanging on:
Chencking the information on your device... Please wait..
Then there is a screen to update. After long time. So when I press the button is still the same info. Checking the information on your device... Please wait..
And its hanging. When I reset to bootloader again the soft telling me:
This ROM Upgrade Utility does not design for your device.
Please get probper ROM Upgrade Utility and try again!
Where can I get the radio version 1.05 for T-Mobile Vario II ???????????
Is there possibility to download from somewhere ?
Or maybe I should try other solution ?
Read "problem 5" here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
Yes, I was tying point 5 few times. The problem is, I can connect through mtty.exe without any problems, but after soft reset, I am pressing POWER and OK button and going to bootloader mode again, and when I am trying to flash the extracted radio ROM (i tried all of them = 4) and there is a problem. nothing is working. I am waiting and waiting, and there is only info: Checking your device information or something like that. What can I do ? Sorry for my English guys.
Instead of flashing an extracted radio image try to flash a normal shipped rom (if possible matching your cid). Capture the process using usb monitor to see where exactly it fails and which error you get.
Where can I download
pof said:
normal shipped rom (if possible matching my cid).
Click to expand...
Click to collapse
?
I had RADIO 1.05 , that I remember, and have a phone from T-Mobile - MDA Vario II.
Benone said:
Where can I download ?
I had RADIO 1.05 , that I remember, and have a phone from T-Mobile - MDA Vario II.
Click to expand...
Click to collapse
No rom matching your cid is available then, use the TyTN 1.18 rom.
pof said:
No rom matching your cid is available then, use the TyTN 1.18 rom.
Click to expand...
Click to collapse
I tried that ROM 2 times, once I plugged with holding camera button and second time without. I made monitor of QTEK rom aswell, because its the one which is changing phone screen from red green blue stripes to completly white. But nothing else is doin...
A attaching logs in zip file below. I have 3 files from each session, I dont know which are correct, 2 of them i saved and 1 is exported.
What do you think ?
I used USB-monitor from http://www.hhdsoftware.com/
very weird... usb seems not working but for what you say bootloader seems to be ok. Are you sure this was after patching the radio with universal unlocker? it seems totally a different problem :-$
I guess you'll have to wait until t-mob releases a ROM matching your CID and then flash it using the hermimg.nbh sd-card flashing method.
You can also try to connect to it via serial, I have no experience on that, but a search on these forums might tell you how...
keep us updated
How long I have to wait ?
Should I go to T-Mobile when I will be back to Scotland and tell them what I did or what ? Did I lose my warranty ? Do you know approximately how much they will charge me for flashing my phone ?
Do I really have no chances to repair it by myself ?
Benone said:
How long I have to wait ?
Click to expand...
Click to collapse
Until t-mobile releases a rom with your cid... it can be today or next year, I don't know.
Benone said:
Should I go to T-Mobile when I will be back to Scotland and tell them what I did or what ? Did I lose my warranty ? Do you know approximately how much they will charge me for flashing my phone ?
Click to expand...
Click to collapse
I don't think you lost the warranty. They usually charge about 100 eur for flashing it back in the service centre. They do it by inserting a diagnostics sd card, but we don't have it for the Hermes
Benone said:
Do I really have no chances to repair it by myself ?
Click to expand...
Click to collapse
You can try flashing over serial port, and you can try sd-card flashing, but for sd-card flashing you need a rom matching your CID first.
Eureka!!!
Finally I made my device working again!
And I dont have simlock !
After trying everything.... ufffff.
THX !!!!!!
1) I downloaded ftp://xda:[email protected]/Hermes/Tools_and_Programs/HTC_Hermes_SIM_Unlock_v1.zip
2) Reset my phone in bootloader mode.
3) Plug USB cable.
4) Run HTC_Hermes_SIM_Unlock_v1.
5) After 20 min. my phone said ELO to meeeee He did not have simlock when was saying that.
YE YE YE
That was simple. If you have any Hermes radio problem, try that first - HTC_Hermes_SIM_Unlock_v1.
Will be more often here, forum seems to be really interesting.
YO!
Yipie
Glad it worked
Hi All
Been dying to upgrade my Advantage 7501 and try out some of the new ROMS and the new radio on here. Went to the sticky and spent a day browsing the forums to see what I could pick up, even went to how not to brick your device thread. However I am still having issues
First thing I did was remove the SIM and SD cards, I had just reset the device yesterday so I did not reset again. I got a hold of the AthenaWrapper program and it worked as advertised. Getting into bootloader I have:
Athe100
IPL-v2.02
Athe100
SPL-v1.20.Olipro
However, this is where I run into issues. A soft reset does nothing but give me a black screen. I can get into the hard reset screen okay but when I cancel out I get back to the black screen.
Device also does not sync up with Activesync or WMDC?
Not sure what to try next or how to get back on track
Have tried on both Vista and XP.
Anyone have any suggestions
JP
Try to flash a ROM now, starting in bootloader mode. Hold the volume slider to down and then press into the reset hole.
Chooose one (SPL 1.2) from the sticky topic in the athena WM6 section
Progress
Thanks for the reply
Went back and remembered I had to flash the radio first. So I got the 1.57 update and that went as planned. One bullet dodged. Then I went ahead and grabbed some of the ROMs from the located you mentioned and that went thru as well. So it looks like I am back in business. Appreciate it.
PS I see references to SPL 1.2 and 3.5. I also read somewhere that the AP4 upgrader containts 3.5 (http://forum.xda-developers.com/showthread.php?p=2825883). Is this just a new version of the same thing?
JP
FollowUp
Just an FYI. I got things to work but not after a few more moments.... I initially tried to update to MichyPrimas 6.1 ROM and it got to 93% complete before bombing with a comm error. That was bad! Went thru the recovery wizard but it basically toasted my model id. Nothing would work. Found a copy of mtty and that did the trick. Just so other know, you need a mac address to run in the mac1.exe program. Some people report having this on the inside of their battery cover. No luck here. I did find it at the router from a connection before I started flashing. A spot of luck there. All went well and I got my model ID back and was able to resume normallly. I flashed the Black Touch PK3 ROM with WM6 for now till I have a bit more time to go to 6.1.
Anyone else have issues with MichyPrima's 6.1 ROM like I did. Looks cool and I want to try it but not if it bombs out on me and I have to mtty my way back all the time.
Cheers
jhenel said:
Just an FYI. I got things to work but not after a few more moments.... I initially tried to update to MichyPrimas 6.1 ROM and it got to 93% complete before bombing with a comm error. That was bad! Went thru the recovery wizard but it basically toasted my model id. Nothing would work. Found a copy of mtty and that did the trick. Just so other know, you need a mac address to run in the mac1.exe program. Some people report having this on the inside of their battery cover. No luck here. I did find it at the router from a connection before I started flashing. A spot of luck there. All went well and I got my model ID back and was able to resume normallly. I flashed the Black Touch PK3 ROM with WM6 for now till I have a bit more time to go to 6.1.
Anyone else have issues with MichyPrima's 6.1 ROM like I did. Looks cool and I want to try it but not if it bombs out on me and I have to mtty my way back all the time.
Cheers
Click to expand...
Click to collapse
Check the SPL version before flashing a new rom!
MIchyPrisma 6.1 Crash / Lost Unit ID / NO MTTY Upload
hello,
just read this thread after the same happens to me... ;(
jhenel wrote :
´Just an FYI. I got things to work but not after a few more moments.... I initially tried to update to MichyPrimas 6.1 ROM and it got to 93% complete before bombing with a comm error. That was bad! Went thru the recovery wizard but it basically toasted my model id. Nothing would work. Found a copy of mtty and that did the trick. Just so other know, you need a mac address to run in the mac1.exe program. Some people report having this on the inside of their battery cover. No luck here. I did find it at the router from a connection before I started flashing. A spot of luck there. All went well and I got my model ID back and was able to resume normallly. ...´
The same hits me.. break after 93%
No kind of rom can be installed, error from the romupdate utility from ´wrong unit id´ to ´can´t use this update tool , you need a newer one´ everything, but no rom will install. all hangs after 1% , stock-roms also.
i tried mtty, everything fine until task 32,level =0
then i want to upload the produced file (mac file generated through mac1.exe,spl1.x)
it starts uploading and ends with ´Fail to synchronize with the host (1)´
any ideas `?
ipl-v2.02
spl-v1.20.olipro
nothing works, only bootloader.
i can connect with mtty, but not upload files.
no rom update works..
help....
greetings,
doktor wahnsinn
http://forum.xda-developers.com/showthread.php?t=429013
you should read this first
http://forum.xda-developers.com/showthread.php?t=429013
Make an effort to search for an answer before asking a question
jhenel said:
Just an FYI. I got things to work but not after a few more moments.... I initially tried to update to MichyPrimas 6.1 ROM and it got to 93% complete before bombing with a comm error. That was bad! Went thru the recovery wizard but it basically toasted my model id. Nothing would work. Found a copy of mtty and that did the trick. Just so other know, you need a mac address to run in the mac1.exe program. Some people report having this on the inside of their battery cover. No luck here. I did find it at the router from a connection before I started flashing. A spot of luck there. All went well and I got my model ID back and was able to resume normallly. I flashed the Black Touch PK3 ROM with WM6 for now till I have a bit more time to go to 6.1.
Anyone else have issues with MichyPrima's 6.1 ROM like I did. Looks cool and I want to try it but not if it bombs out on me and I have to mtty my way back all the time.
Cheers
Click to expand...
Click to collapse
please people, READ!!!! someone above your post just told you to flash 1.2 rom, in BIG RED LETTERS.
the AP4 is what upgrades you to SPL 3.5, then you won't have a problem with 3.5 roms
(btw good thing this reminds me to release a separate 3.5 SPL upgrader)
doktor.wahnsinn said:
hello,
i tried mtty, everything fine until task 32,level =0
then i want to upload the produced file (mac file generated through mac1.exe,spl1.x)
it starts uploading and ends with ´Fail to synchronize with the host (1)´
any ideas `?
ipl-v2.02
spl-v1.20.olipro
nothing works, only bootloader.
i can connect with mtty, but not upload files.
no rom update works..
help....
greetings,
doktor wahnsinn
Click to expand...
Click to collapse
please read my really detailed instructions a bit more carefully. I could bet you skipped the part about trying to copy all the files and mtty to C:\ or the step saying click OK for the small popup in mtty. or the warning that you need to type full filename includign the .bin file extension.
also i hope you use the version of mtty i posted
if that's not it, you can also try a different PC