Hi All
Been dying to upgrade my Advantage 7501 and try out some of the new ROMS and the new radio on here. Went to the sticky and spent a day browsing the forums to see what I could pick up, even went to how not to brick your device thread. However I am still having issues
First thing I did was remove the SIM and SD cards, I had just reset the device yesterday so I did not reset again. I got a hold of the AthenaWrapper program and it worked as advertised. Getting into bootloader I have:
Athe100
IPL-v2.02
Athe100
SPL-v1.20.Olipro
However, this is where I run into issues. A soft reset does nothing but give me a black screen. I can get into the hard reset screen okay but when I cancel out I get back to the black screen.
Device also does not sync up with Activesync or WMDC?
Not sure what to try next or how to get back on track
Have tried on both Vista and XP.
Anyone have any suggestions
JP
Try to flash a ROM now, starting in bootloader mode. Hold the volume slider to down and then press into the reset hole.
Chooose one (SPL 1.2) from the sticky topic in the athena WM6 section
Progress
Thanks for the reply
Went back and remembered I had to flash the radio first. So I got the 1.57 update and that went as planned. One bullet dodged. Then I went ahead and grabbed some of the ROMs from the located you mentioned and that went thru as well. So it looks like I am back in business. Appreciate it.
PS I see references to SPL 1.2 and 3.5. I also read somewhere that the AP4 upgrader containts 3.5 (http://forum.xda-developers.com/showthread.php?p=2825883). Is this just a new version of the same thing?
JP
FollowUp
Just an FYI. I got things to work but not after a few more moments.... I initially tried to update to MichyPrimas 6.1 ROM and it got to 93% complete before bombing with a comm error. That was bad! Went thru the recovery wizard but it basically toasted my model id. Nothing would work. Found a copy of mtty and that did the trick. Just so other know, you need a mac address to run in the mac1.exe program. Some people report having this on the inside of their battery cover. No luck here. I did find it at the router from a connection before I started flashing. A spot of luck there. All went well and I got my model ID back and was able to resume normallly. I flashed the Black Touch PK3 ROM with WM6 for now till I have a bit more time to go to 6.1.
Anyone else have issues with MichyPrima's 6.1 ROM like I did. Looks cool and I want to try it but not if it bombs out on me and I have to mtty my way back all the time.
Cheers
jhenel said:
Just an FYI. I got things to work but not after a few more moments.... I initially tried to update to MichyPrimas 6.1 ROM and it got to 93% complete before bombing with a comm error. That was bad! Went thru the recovery wizard but it basically toasted my model id. Nothing would work. Found a copy of mtty and that did the trick. Just so other know, you need a mac address to run in the mac1.exe program. Some people report having this on the inside of their battery cover. No luck here. I did find it at the router from a connection before I started flashing. A spot of luck there. All went well and I got my model ID back and was able to resume normallly. I flashed the Black Touch PK3 ROM with WM6 for now till I have a bit more time to go to 6.1.
Anyone else have issues with MichyPrima's 6.1 ROM like I did. Looks cool and I want to try it but not if it bombs out on me and I have to mtty my way back all the time.
Cheers
Click to expand...
Click to collapse
Check the SPL version before flashing a new rom!
MIchyPrisma 6.1 Crash / Lost Unit ID / NO MTTY Upload
hello,
just read this thread after the same happens to me... ;(
jhenel wrote :
´Just an FYI. I got things to work but not after a few more moments.... I initially tried to update to MichyPrimas 6.1 ROM and it got to 93% complete before bombing with a comm error. That was bad! Went thru the recovery wizard but it basically toasted my model id. Nothing would work. Found a copy of mtty and that did the trick. Just so other know, you need a mac address to run in the mac1.exe program. Some people report having this on the inside of their battery cover. No luck here. I did find it at the router from a connection before I started flashing. A spot of luck there. All went well and I got my model ID back and was able to resume normallly. ...´
The same hits me.. break after 93%
No kind of rom can be installed, error from the romupdate utility from ´wrong unit id´ to ´can´t use this update tool , you need a newer one´ everything, but no rom will install. all hangs after 1% , stock-roms also.
i tried mtty, everything fine until task 32,level =0
then i want to upload the produced file (mac file generated through mac1.exe,spl1.x)
it starts uploading and ends with ´Fail to synchronize with the host (1)´
any ideas `?
ipl-v2.02
spl-v1.20.olipro
nothing works, only bootloader.
i can connect with mtty, but not upload files.
no rom update works..
help....
greetings,
doktor wahnsinn
http://forum.xda-developers.com/showthread.php?t=429013
you should read this first
http://forum.xda-developers.com/showthread.php?t=429013
Make an effort to search for an answer before asking a question
jhenel said:
Just an FYI. I got things to work but not after a few more moments.... I initially tried to update to MichyPrimas 6.1 ROM and it got to 93% complete before bombing with a comm error. That was bad! Went thru the recovery wizard but it basically toasted my model id. Nothing would work. Found a copy of mtty and that did the trick. Just so other know, you need a mac address to run in the mac1.exe program. Some people report having this on the inside of their battery cover. No luck here. I did find it at the router from a connection before I started flashing. A spot of luck there. All went well and I got my model ID back and was able to resume normallly. I flashed the Black Touch PK3 ROM with WM6 for now till I have a bit more time to go to 6.1.
Anyone else have issues with MichyPrima's 6.1 ROM like I did. Looks cool and I want to try it but not if it bombs out on me and I have to mtty my way back all the time.
Cheers
Click to expand...
Click to collapse
please people, READ!!!! someone above your post just told you to flash 1.2 rom, in BIG RED LETTERS.
the AP4 is what upgrades you to SPL 3.5, then you won't have a problem with 3.5 roms
(btw good thing this reminds me to release a separate 3.5 SPL upgrader)
doktor.wahnsinn said:
hello,
i tried mtty, everything fine until task 32,level =0
then i want to upload the produced file (mac file generated through mac1.exe,spl1.x)
it starts uploading and ends with ´Fail to synchronize with the host (1)´
any ideas `?
ipl-v2.02
spl-v1.20.olipro
nothing works, only bootloader.
i can connect with mtty, but not upload files.
no rom update works..
help....
greetings,
doktor wahnsinn
Click to expand...
Click to collapse
please read my really detailed instructions a bit more carefully. I could bet you skipped the part about trying to copy all the files and mtty to C:\ or the step saying click OK for the small popup in mtty. or the warning that you need to type full filename includign the .bin file extension.
also i hope you use the version of mtty i posted
if that's not it, you can also try a different PC
Related
I was trying to upgrade to radio v1.43 in the hope that battery life was improved over 1.41 however when it got to 8% it stopped and gave me an error i can't remember After atempting to recover, it got off the three colour screen now the 3100 stalls on the blackshadow version4 screen (bootloader screen?) and goes no further. I tried reflashing but got a 260 and using mtty, only getting 2 com port options, didn't offer any help.
I'm really sorry to have not been able to sort this with reading through the relevant post but I haven't found a solution. What else can I try?
Hi,
Could you pls advise what is your device made, model, SPL version ... etc.
Also did you try to do Hard reset?
I'm using now black MAJIK (and few days ago black shadow) with radio 1.43 with no problem.
its the SPV m3100 When I decided to go Black shadow I read up on mr vanx and made sure I had all the things I needed. If I remember right, when I came to upgrade to Majik the auto detect found the second option down
SPL-1.04/1.10 - 1.09 Bootloader. I've realized since I had a spaz and ran the RUU from the archive this time. From what I've since read thats not too cleaver.
I have tried a hard reset and took the battery out instead of pressing space.
I dont know if this information on the starter screen is of use
M 05
S 04
B 05 D 3lak
I'm not sure, but hard reset doesnt mean you take the batery out.
Please check that link:
http://wiki.xda-developers.com/index.php?pagename=Hermes_For_Beginners#hardreset
I was in your position (hanged on booting) few days ago, and when i did hard reset, it changes every thing to basic normal condition.
i meant when i did a hard reset when it asked me to press space to reboot I took the battery out. I tried again this time pressing space to reboot but I still get stuck on the loading screen. I can't connect by USB to the PC I'm guessing the drivers on the phone haven't loaded and I'm stuck as to what to do.
Does anyone have any ideas?
try look at it http://forum.xda-developers.com/showthread.php?t=286755
ok I've tried everything I can think of to connect the 3100 to the computer so I can reflash it but mtty gives only com 1 and com2 but no USB and neither those two work, active sync wont connect so I disabled it as suggested and running the radio ruu and wrapper wont querry the device. I am now at a loss as to what to do next someone must know what I should do. Please?
what is your SPL?
try this http://wiki.xda-developers.com/index.php?pagename=HTC_Hermes
sl is 1.09 i'd updated it on the previously successful black shadow flash
msn [email protected]
icq 150277111
AIM TazmanFH9
Yahoo bigfathairyboggart
I have tried changing KITL trasport but I am unable to select or chose either option. I have also tried the rversion command in the tri colour screen but nothing happens. I hope I'm missing something nice and simple but I get the feeling I'm not going to be that lucky. Please help
tcSPVm3100 said:
sl is 1.09 i'd updated it on the previously successful black shadow flash
Click to expand...
Click to collapse
I suggest you check again, press and hold the side OK button and the power button...then put the stylus into the hole in the bottom of the unit.
yeah I've done that it's "SPL-1.09"
I had this exact problem yesterday, with the same bootloader too. The phone would not pass the splash and IT refused to upgrade. I ended up downgrading to a shipped wm5 rom (in my case the cingular 1.30.502.1_1.11.00.00) which to my surprise actually worked as no rom radio or spl upgrade moved at al on my phone. Then upgraded back to black majik. I hope this helps.
Thanks. I downloaded the trial of wm5 from the windows website and it asked me to install .NET framework version 1 so I got that but it turns out to be 2.0 not 1.1 It would say it had repaired but it would say this with or without the phone connected.
tcSPVm3100 said:
Thanks. I downloaded the trial of wm5 from the windows website and it asked me to install .NET framework version 1 so I got that but it turns out to be 2.0 not 1.1 It would say it had repaired but it would say this with or without the phone connected.
Click to expand...
Click to collapse
Just download a WM5 ROM from the wiki page!
ok tried this too no luck.
Trying to use the one from orange (linked to through wikki) I get an 294 invalid vendor error however active sync cannot connect yet of course so is this to be expected?
I have however gotten a connection with mtty which is a step forward dunno what to do with it yet though except trying the password 0000000000000000 command but it not disabling the password. This then lead me to read for a further hour how to change it and I've got to be honest; it beat me. I have No idea what the hell its talking about. My head hurt with so much reading.
I get a no gsm pop up v briefly on loader. I so want my phone back
I have since tried CID unlocker just so i get something installed onto this brick but I either get a connection error or it telling me it can't install for some other reason. I can not set the password in mtty to 0000000000000000 so how do I do that and is this the first step to getting things sorted? "just running a rom install" is not happening I can get a USB connection in mtty and that is it. Is the fact i'm running SPL 1.09 a problem? I'm getting precious little help guys If i'm posting in the wrong place or something please let me know. I need thing thing back now. Hours are drifting by with me trying to get some head knowledge but I still need some guidance please
tcSPVm3100 said:
I have since tried CID unlocker just so i get something installed onto this brick but I either get a connection error or it telling me it can't install for some other reason. I can not set the password in mtty to 0000000000000000 so how do I do that and is this the first step to getting things sorted? "just running a rom install" is not happening I can get a USB connection in mtty and that is it. Is the fact i'm running SPL 1.09 a problem? I'm getting precious little help guys If i'm posting in the wrong place or something please let me know. I need thing thing back now. Hours are drifting by with me trying to get some head knowledge but I still need some guidance please
Click to expand...
Click to collapse
can u flashing HARD V7?,i think better u have IPL 1.04 SPL 2.10olipro first ,then try to flashing radio?
and did u try SD card.
In bootloader can anyone here connect with active sync? I can't so updating rom and radio flashes in the usual way isn't possible. Trying the hard spl again it tells me to make sure active sync is connected and as it isn't it throws back a 262 update error. 0% on the hermes and that's currently as far as I can get. I have no means with which to access the memory card.
The reason you get an invalid vendor ID is because your CID doesnt match....download a ROM which is for your device (an orange one?)...then try.
You need to read the wiki alot more before trying anything else since you are not aware of the vendor ID error...nor the fact you MUST use HardSPL.
I linked to the orange ROM from wikki and tried installing it. it was while installing THIS ROM SPV_M3100_ROMUpdate_0407.exe I got invalid vendor error.
Installing a recent DL on HARD spl v7 I get a 240 open file error that's one I haven't had before.
With all other attempts they all say they want an active sync connection.
I can not connect to the phone through active sync
so all attempts by me to flash anything to the phone using an RUU fails.
All rite here we go, in advanced i thank u guys for trying to help me out here.
First, i'm a n00bie compared with the most of u guys.
My Device:
Tytn Herm 300
OS: Schaps Purple 3.30c
SPL: Hard-Spl 2.10 oli
Radio: 1.16.00.00 !Hmzz...that's the problem!
My phone functionallity sucks...some how it keep loosing connection while i see the phone indication bar up to 3 bars. So i decided to do something about it.
Beeing a noob i thought it got to do something with the OS. So i upgrade it to Schaps's wonderfull purple WM6 Hermes 3.30c and loaded the Hard SPL 2.10 oil V7. All went great, and my Hermes never looked so cool before.
But now i'm trying to upgrade my radio, which is still version 1.16.00.00, to what ever better version. I tried every radio upgrade possible from this list:
http://wiki.xda-developers.com/index...actedRadioRoms
Every single one starts well. passed the information retrieving from my phone. Confirmed the update, and then there was the installation progress bar....
All versions of the radio roms i downloaden get stuck in here. It doesn't even start..0% and error... And really i dun have any idea why.
So after re-flashing a gazillion times, i decided to ask help to the allmighty XDA community. So pls, if anybody there got a suggestion or the solution...i would be so thankfull and will slaughter a goat to worship you
If you've got schaps Rom and HardSPL on your phone then you obviously don't have problems flashing or with PC/phone comms.
When you try flashing the radio, how long do you wait before deciding it doesn't work? I've found that some of them can take what seems like a really long time and I'm tempted to unplug and start again.
Maybe try again, then go make yourself a cup of tee/coffee or get a beer then come back 10 minutes later. If the upgrade still hasn't worked we'll have to look a bit deeper
RaDeNRFX said:
- I am so sorry posting this twice in the wrong sections, it seems that i'm a really noobie forum user - But i finally found the rite section. So my humble excuses.
All rite here we go, in advanced i thank u guys for trying to help me out here.
First, i'm a n00bie compared with the most of u guys.
My Device:
Tytn Herm 300
OS: Schaps Purple 3.30c
SPL: Hard-Spl 2.10 oli
Radio: 1.16.00.00 !Hmzz...that's the problem!
My phone functionallity sucks...some how it keep loosing connection while i see the phone indication bar up to 3 bars. So i decided to do something about it.
Beeing a noob i thought it got to do something with the OS. So i upgrade it to Schaps's wonderfull purple WM6 Hermes 3.30c and loaded the Hard SPL 2.10 oil V7. All went great, and my Hermes never looked so cool before.
But now i'm trying to upgrade my radio, which is still version 1.16.00.00, to what ever better version. I tried every radio upgrade possible from this list:
http://wiki.xda-developers.com/index...actedRadioRoms
Every single one starts well. passed the information retrieving from my phone. Confirmed the update, and then there was the installation progress bar....
All versions of the radio roms i downloaden get stuck in here. It doesn't even start..0% and error... And really i dun have any idea why.
So after re-flashing a gazillion times, i decided to ask help to the allmighty XDA community. So pls, if anybody there got a suggestion or the solution...i would be so thankfull and will slaughter a goat to worship you
Click to expand...
Click to collapse
ach2 said:
If you've got schaps Rom and HardSPL on your phone then you obviously don't have problems flashing or with PC/phone comms.
When you try flashing the radio, how long do you wait before deciding it doesn't work? I've found that some of them can take what seems like a really long time and I'm tempted to unplug and start again.
Maybe try again, then go make yourself a cup of tee/coffee or get a beer then come back 10 minutes later. If the upgrade still hasn't worked we'll have to look a bit deeper
Click to expand...
Click to collapse
I waited till the Program says connection error...and send me to recovery proces. And i've been making hella tons of coffee after trying to flash that many Radio Roms. Any other suggestions? I'm so desperate
Ok, maybe some more info...
Do you see 'NO GSM' during the phone boot process?
Do you have no radio at all or just intermittent reception?
Are you running Vista?
What is the connection error number?
If you've lost the radio but have hard SPL it may just be a case of re-flashing an original manufacturers ROM (which will include the radio) then start your upgrading again afterwards. Don't forget to back-up data before flashing.
If you do flash a manufacturers shipped rom - check that you still have HardSPL afterwards.
ach2 said:
Ok, maybe some more info...
Do you see 'NO GSM' during the phone boot process?
Do you have no radio at all or just intermittent reception?
Are you running Vista?
What is the connection error number?
If you've lost the radio but have hard SPL it may just be a case of re-flashing an original manufacturers ROM (which will include the radio) then start your upgrading again afterwards. Don't forget to back-up data before flashing.
If you do flash a manufacturers shipped rom - check that you still have HardSPL afterwards.
Click to expand...
Click to collapse
Well the weird part is "No GSM" appeared occasionally...some times it shows it sometimes it's not showing it.
No...i'm a Vista hater. And dun have the original manufacturers ROM. I've got the "T-Mobile Vario II" from The Netherlands..so if anybody got a link for the original version i'd be thankfull.
The Radio it self is intermittent and very inpredictable...for example:
Radio indicator says i got full recieve:...but i can't call or recieve any.
Connection error: 262 (which is, if i'm not mistake a connection error.) Which is bull cuz i'm re-running every other ROM's upload with the same way and succeded/
Radio indicator says no reception and shows an exclamation mark:...and my GF just called me to hurry up and pick her up :/
But the weird part is...it seems that my radio ROM is locked somehow. I can upgrade or downgrade SPL's and OS ROM's but not the Radio ROM.
I've tried to use MTTY by now and followed the manual bellow: (Problem 5)
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#problem5
But it began with invalid password. Procede as written and it didn't helped.
More suggestions are welcome
My bad...i didn't looked well enough. It is saying No GSM the whole time.
More information:
I've checked the Device information on the Hermes now some information are blank:
Radio: Blank
Protocol version: Blank
IMEI: Blank
All other information field are filled. Been spending hours reading tutorials and manuals...and nothing. HELP!
OK,
This isn't a problem I've had myself, but loads of other people have and there are quite a few threads on how to unbrick from here... you're going to have to do a bit of reading.
This page shows the different combinations of OS/radio/brick type etc and should point you in the right direction for the correct course of action http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
Then read through this thread http://forum.xda-developers.com/showthread.php?t=286755 . It's got really long but read the beginning where POF describes the types of problem and also the solutions. Then it's probably best to jump to somewhere near the end and pick someone who has a similar problem.
It sounds to me as though you need to just flash a radio in nbh format, but please do some more reading before you do this to check my advice - as I said at the beginning, I haven't had this problem so I'm only giving advice from what others have written.
ach2 said:
It sounds to me as though you need to just flash a radio in nbh format, but please do some more reading before you do this to check my advice - as I said at the beginning, I haven't had this problem so I'm only giving advice from what others have written.
Click to expand...
Click to collapse
I am really thankfull of ur post. Unfortunately, i've been doing some reading. Including the link u gave me. The problem is that i can't upload/flash Radio in nhb format.
As i described in the first place, i can't load a nhb format radio in RUUWrapper.exe properly. It can start the proces..but it always end up with a connection error code 260/262 during the installation progres bar (0%).
The solutions some ppl tried in ur link is often not my case. And the similar cases i have tried where i end up with the same grumpfy situation.
have you tried to flash the radio using the SD card method? I too have a cable connection problem but I fear mine may be hardware failure.
Yap...and no luck
Even after reading this forum all nite, I am still soooo confused, maybe too much new info in m'head. At any rate, I am trying to UG from WM5 to WM6 and am having a heck of a rough time. Everything goes good until it actually starts the process, at which time I get the 260 Connection Error. After plenty of research on here, I decided to try to "flash" the ROM, to no avail, for nothing happened. I can get into bootloader mode but then nothing else happens (perhaps I'm not waiting long enough? How long should I wait?) and I never see the screen pictured here - http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing - so I just give up and reset. I am currently downloading the HardSPL utility so I can try flashing after the IPL and SPL ugrades. But I do have some questions still --
(1) Does my phone need to be "unlocked" to do this and how can I tell if it is or isn't?
(2) Can I just use the ROM that I downloaded from the HTC site or must I use one found somewhere on this forum?
Any other advice? All will be appreciated. Thanx.
Oh, yeah -- I'm working with a Cingular 8525 Hermes [HERM100 model number] Pocket PC. It's specs are:
ROM version 2.15.502.3
ROM date 04/09/07
Radio version 1.40.30.00
IPL 1.03
SPL 1.11
Have you read this http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeForBeginners ?
Re:
Yes, I have, plus all the links branched from there. After about 3 hours of reading, I felt ready to try flashing, but it didn't work. The HardSPL utility is done downloading, so when I get home I'll try that and hope I finally get a successful upgrade. If not, I'll be back to the forums. Thanx!
What ROM are you upgrading to? The official AT&T ROM? I'd try that first if you're not already.
BDsBabyGirl said:
Even after reading this forum all nite, I am still soooo confused, maybe too much new info in m'head. At any rate, I am trying to UG from WM5 to WM6 and am having a heck of a rough time. Everything goes good until it actually starts the process, at which time I get the 260 Connection Error. After plenty of research on here, I decided to try to "flash" the ROM, to no avail, for nothing happened. I can get into bootloader mode but then nothing else happens (perhaps I'm not waiting long enough? How long should I wait?) and I never see the screen pictured here - http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing - so I just give up and reset. I am currently downloading the HardSPL utility so I can try flashing after the IPL and SPL ugrades. But I do have some questions still --
(1) Does my phone need to be "unlocked" to do this and how can I tell if it is or isn't?
(2) Can I just use the ROM that I downloaded from the HTC site or must I use one found somewhere on this forum?
Any other advice? All will be appreciated. Thanx.
Oh, yeah -- I'm working with a Cingular 8525 Hermes [HERM100 model number] Pocket PC. It's specs are:
ROM version 2.15.502.3
ROM date 04/09/07
Radio version 1.40.30.00
IPL 1.03
SPL 1.11
Click to expand...
Click to collapse
What operating system are you using? If its Vista you MUST use Mr. Vanx's guide to get past the connection problem. The standard Vista HTC driver is wrong when we want to flash rom's in bootloader mode and vista WMDC. Get it here:
MR VANX's VISTA GUIDE
Hard SPL is great after that. Just remember you warranty may be void if you have to go to AT&T for repairs and the see that bootloader. You shouldn't need Hard SPL to flash the standard AT&T rom or VP3G's or other AT&T based ROM's, but better safe than sorry.
Be sure to close EVERYTHING in the taskbar! Don't start any programs, allow any updates to mess around with the computer while its flashing..In fact, I disable my AV program and internet connection totally when I flash ROMS. (My Kaspersky started updating and virus scanning during my 1st flash..sucker froze and freaked me out!)
Once I dealt with unlocking and connection issues, I flashed the standard AT&T ROM, performed a hard reset immediately and then connected via WMDC and synced everything. I tested it for a few hours then decided to flash VP3G's excellent AT&T based ROM v3.62.3..I like to do a hard reset immediately after flashing to burn everything in...I've seen others in this forum do the same.
Another ROM I've found fun is S64's(Starbase64) 3.62 WWE v9 - It's not AT&T based but you can get WPBEAR's Config files to set your Medianet and proxy. There are other At&T settings CABs out there like Dr. Puttinghams. S64 ROM also includes Advanced Config 1.1 to set your keyboard to Cingular mapping.
Good Luck!
re:
My desktop PC is running Windows XP...
After trying the HardSPL method - which upgraded perfectly - I continue to have the above-mentioned problems; 260 Connection Error and inability to move beyond the tri-color screen to the one pictured on the page which instructs how to flash via SD card.
Thanx for the list of ROMs I can try. For the record, I have been using the "official" one I downloaded from the HTC website. *sigh* I guess I'll next look for the tutorial I saw somewhere around here on how to upgrade from the tricolor screen [or something like that, I think it was], as well as your advice.
But I do have another question -- how do I format the SD card? The tutorial I used on flashing with it mentioned formatting so I'll retry it with the card newly formatted (I didn't because it said I could just delete everything off the card OR format it).
I'll let you know how it goes...
Ahhh...Sorry for your troubles...I didn't have luck catching an upgrade from the SD Card method on my 8525 either.
I know it seems a bit much but, is your active sync working correctly? Upgraded to 4.5 and all that? Can you sync and Backup all your data then try uninstal, reboot, re-installing AS?
I wonder what would happen if one tried Mr Vanx's instructions on a Win XP box?
I also had heard somewhere about messing around with when Active sync is started. Also as a last ditch, maybe try this from the HTC Wiki:
http://www.htcwiki.com/thread/667087/ActiveSync+and+Rom+8525?t=anon
Good luck
BDsBabyGirl said:
My desktop PC is running Windows XP...
After trying the HardSPL method - which upgraded perfectly - I continue to have the above-mentioned problems; 260 Connection Error and inability to move beyond the tri-color screen to the one pictured on the page which instructs how to flash via SD card.
Thanx for the list of ROMs I can try. For the record, I have been using the "official" one I downloaded from the HTC website. *sigh* I guess I'll next look for the tutorial I saw somewhere around here on how to upgrade from the tricolor screen [or something like that, I think it was], as well as your advice.
But I do have another question -- how do I format the SD card? The tutorial I used on flashing with it mentioned formatting so I'll retry it with the card newly formatted (I didn't because it said I could just delete everything off the card OR format it).
I'll let you know how it goes...
Click to expand...
Click to collapse
Just another tip... Try a different usb port. I've found that sometimes certain usb ports behave differently during the upgrade procedures. So, far I've upgraded three 8525's on Win XP and only one gave me the problem you've described and connecting the sync cable in another port corrected the problem.
Re: my Post
shihayadreamer said:
...I also had heard somewhere about messing around with when Active sync is started. Also as a last ditch, maybe try this from the HTC Wiki:
http://www.htcwiki.com/thread/667087/ActiveSync+and+Rom+8525?t=anon
Good luck
Click to expand...
Click to collapse
OMG! SHIHAYADREAMER! That was JUST the TICKET! I read it and realized that I'd been doing it right all along, I just didn't realize I was! THIS time, I hooked up my cable at the very beginning and let it go. Before, I'd started waiting to hook it up until the instructions asked if I had because I'd gotten to the tricolored screen (the bootloader?) the 1st time and figured I did something wrong. Thanx to that forum, I returned to what I did the very first time and got victory! *falls down sobbing and weeping with joy* I wasted 25 hours because of fear! OMG! *dances around, singing* I've got WM6! I've got WM6!
I know that being reminded to turn off my firewall and stop all the programs in the taskbar played a big role, as well. But I just give a big "Thanx" (on Thanksgiving! *LOL*) to everyone who answered this board because you all helped me so very very much.
Hello, I am in serious trouble! I got a brand new HTC Athena with Windows Mobile 5.0. I succesfully upgrade it to Windows Mobile 6.0.
All was OK.
Than I was interested to move into Windows Mobile 6.1 and possibly 6.5. At first I did the Athena unlock (3 step process) and all went OK: Antenna 1.5.0, SPL 1.2 OLI....
THAN I DID MY ERROR! I try to upgrade my 6.0 ROM with the Micky 6.1 cooked file with SPL 3.5. After a 92 percent upgrade, the ROM crashed and now I always get a nasty black screen with few lines (No 3 color bands!). When I try to upgrade again the same ROM or ROM for SPL 1.2 I get an error (ID mismatching). I guess the only solution is a hard and full reset of the Windows. But doing only a hard reset with the PDA will NOT change my error message and I will keep see this nasty black screen and I cannot load the Windows ActiveSync application-
I am totally lost. Help please. Any tool for a true full restore/recover??? (I did NOT make any backup!).
This thread might hold a solution to your problem.
Hi
If you follow the instructions exactly in post 33, it will solve your problems. just click HERE
Jay
Hello, those links are basically for corrupted wifi antenna files.-
In my case my HTC Athena crashed the Windows 6 ROM while I was attempting to upgrade, after unlocking the phone, the Athena from version 6.0 to version 6.1
Are you sure I can use the post #33 also for my specific trouble?
Thank you in advance!
this is also to repair your bootloader-infos
if you look at your bootloaderscreen, you will see ATHE100, IPL, ATHE100, SPL. if not, you have to repair it
make sure you flashed the right rom, spl 1 or 3.5
How can the bootloader get repaired?
yes use that link, post #33. fixes both wifi and modelid problems and bootloader problems when you got stuck at 92% of the flashing process.
Cannot re flash ROM
Please help! I tried the unlocker and it failed at 92% and since then I have no WM6. Then I tried to flash the Michy WM6.5 and that failed. I was getting model id errors so I did the mtty and mac1 fix which was succesful. However all I can get now is a grey screen on boot-up. I can get to the bootloader screen and it displays ATHE100, IPL-v2.02, ATHE100, SPL-v1.20. Olipro. From what I have read on the forum at this stage I should run a RUU to flash a WM6 ROM but all that I try can't connect because no OS running to connect with Activesync? Is there a way to flash from the bootloader? The other option seems to be putting an image and flasher on a miniSD but I can't find clear instructions for this or which files?
Please ignore - my battery wasn't charged enough. Replaced battery and recovered device.
Still Major Problem! Help me! Have mercy!
Hello Responderman, all,
I have follow the link (thread 33)...., however, after I have typed lnbs filename.bin 75108000 (I have SPL 1.2), I got in mtty the "code entrypoint unknown" message, which should be ok......
However, after I have disconnected the usb cable of the Athena from the PC and try to reboot it, I got again the exact same, nasty, dark screen with blue strips.....:-( It means that my damaged firmware has NOT been fix and in fact I am still NOT able to boot WM successfully!
PLEASE HELP. It is 3 months with this problem and I cannot use my device.:-(
Still Major Problem! Help me! Have mercy!
Hello Responderman, all,
first, how can I get the mac address of my device? It is NOT written anywhere in the Athena parts (checked in the battery bay and so on.....), and so when I run mtty i am in trouble! I have used a mac address got from my company's manager, but not sure it is ok to use it with the Athena!
Anyway,......I have follow the post link (thread 33)...., and followed the various steps.- However, after I have typed lnbs filename.bin 75108000 (I have SPL 1.2), I got in mtty the "code entrypoint unknown" message, which should be ok......
However, after I have disconnected the usb cable of the Athena from the PC and try to reboot it, I got again the exact same, nasty, dark screen with blue strips.....:-( It means that my damaged firmware has NOT been fix and in fact I am still NOT able to boot WM successfully!
PLEASE HELP. It is 3 months with this problem and I cannot use my device.:-(
Solved!
Hi, problem done. I have follow the remarks, fixed my broken firmware and now I use well Athena with VM 6.5! Thanks all for your help!
puffo said:
Hi, problem done. I have follow the remarks, fixed my broken firmware and now I use well Athena with VM 6.5! Thanks all for your help!
Click to expand...
Click to collapse
Can you tell what you've actually done after you've changed ROM with Mtty?
I done the thing with Mtty but just as you described when I reset it now I still get the grey screen. And if I try to update ROM it fails again on 92%
where did you find the upgrade from wm5 to wm6?
the link I found on rapidshare seems not be availabel anymore
Hi guys,
Mods - first time post and im not a regular user so if im breaking the rules i apologise. I have spent hours already trawling the forums, but i am now admitting defeat and I need your help!
My Problem:
I have an x7501 SPL 1.06 0000, WM 5.0, GERMAN OS
I want to upgrade this to WM6.1 ENGLISH
I dont care what the SPL is, as long as it works, is reliable, and wont disable any standard WM functionality
I am not interested in tweaks, hulks, or other (non standard) tricks, i just want to get the device running a stock WM 6.1 rom
That said - if you guys think that going to 6.5 is the best (non beta, no risk) option, then im quite happy to go that route.
$50 reward to the first person who provides the following info IN A FORMAT THAT I CAN UNDERSTAND. im good with computers for a non pro (and can follow instructions , but this is just over my head!
I Need:
1) Link to an unlocker and instructions how to use, that will give me the required SPL (note my SPL is 1.06 - will this require two SPL flash steps??)
2) Link to a stable ROM that retains all windows functionality, and instructions how to use it.
If i find that i used two or more peoples help i will split the reward accordingly!
thanks in advance and keep up the good work!
Alan K
First you need to download the unlocker from this thread and follow instructions... http://forum.xda-developers.com/showthread.php?t=315831
This will give you SPL 1.2
Here is a handy thread with step by step instructions on upgrading your roms you should read through before beginning to flash...http://forum.xda-developers.com/showthread.php?t=429013
Unfortunately, the stock-like wm6.5 roms made by michy-prima that ran on spl1.2 are no longer hosted on any sites anymore. I can try to contact him for you and see if I can get a copy directly from him. I will see if I can do that.
Otherwise, you can change your spl to 3.5, which you might as well do anyways, as there are more roms for that spl and even the stock-like michy-prima roms were made in spl3.5 also, so if I can get those, I will get the spl 3.5 versions.
So to then change your spl to 3.5, you must have first used unlocker to make spl 1.2, then the only way that was made to change spl to 3.5 was to flash the Athena Project 4 rom, so go to this thread... http://forum.xda-developers.com/showthread.php?t=387409 and download the AP ROM V.4, unzip it, and run the flasher while your phone is connected with active-sync to your computer. This will install the spl3.5 and the AP4 Rom.
Now that that is done, you can choose any SPL3.5 ROM to flash... (make sure to only flash SPL3.5 Roms now... if need be, there is a way to go back to SPL1.2 if you need to, but there really is no reason you would need to.)
Probably the most modern rom with the most features would be the AGB Version 3.00 ROM, The Hulk one (I know you said you didn't want that, but it is the most current rom, and you can easily change the theme and wallpaper on it. This is the ROM I have on my Athena... its a nice ROM.) Here is the thread for that ROM... http://forum.xda-developers.com/showthread.php?t=614158
Just unzip the rom after you download it, and like before, hook phone up to computer and let it sync, then run the installer. You can also use the ealier AGB roms, too, if they look better to you, or any rom you come across as long as it is a spl3.5 rom.
And I will try to contact michy-prima to see if I can get one of his old clean wm6.5 roms or his stock wm6.1 roms, but I wouldn't count on me being able to get one from him. Personally I think the newer AGB ROMs are alot better and more recent and updated and would recommend using them.
Also, here is a convenient thread I just found that has links to many different builds and useful tools and guides... http://forum.xda-developers.com/showthread.php?t=397518 ... so if you want to try out a couple wm6.1 while you have spl1.2 or even after flashing spl3.5, as a lot of roms are made for both spls. Just make sure you only flash roms made for the spl that you have on your phone.
I hope this helps... if you have any more questions, feel free to pm me and I'll be glad to help. Happy flashing!
Hi Zarathustrax,
Thanks for the extensive instructions. I will be checking it this week so hopefully ill be sending you some greenbacks by Friday!
Thanks again!
Al
bigalk said:
Hi Zarathustrax,
Thanks for the extensive instructions. I will be checking it this week so hopefully ill be sending you some greenbacks by Friday!
Thanks again!
Al
Click to expand...
Click to collapse
Like I said, if you have any more questions or problems, feel free to ask here or pm me.
Sent from my HTC HD2 using XDA App
Also, if you prefer to have a winmo 6.1 ROM over the 6.5 ROM I suggested, there are links to many 6.1 ROMs in that last thread I linked. Here's the link again... http://forum.xda-developers.com/showthread.php?t=397518
MichyPrima's roms are no longer hosted, but I have heard good things about Taxists and Sogarths ROMs. You can easily try a rom and then flash another if you don't like it. Just remember, make sure to flash roms for the spl that you have. If you have SPL3.5 and want a spl1.2 rom, there are links to the tool to change back to spl1.2. The only way to go from spl 1.2 to spl 3.5 is to flash the Athena Project 4 ROM, then after that you can flash any spl3.5 you want. Let me know if you have any other questions or concerns.
Hi Zarathustrax,
just to let you know - i still havent managed to allocate time to this yet.
I havent forgotten about you, and im not pulling a fast one!
thanks again for your time and effort!
Al
Hi Zarathustrax,
In the very first step (unlocker link) Olipro says "follow the steps...."
I cant see the steps he mentions anywhere? This is one of the reasons for my original post
any ideas?
Al
Forget my last question - unlocker has the steps!
Hi Zarathustrax,
tried twice and i keep getting error 202 - "check cables....... cannot connect to phone"
I have:
1) connected and synced via active sync
2) set active sync not to sync any items except for files
any ideas?
thanks
Ive tried everything i can. ALL windows updates installed (along with .net 2.0)
AV disabled
Athenaunlocker added to firewall exceptions - im on a work network so firewall is controlled through group policy - so i cant completely disable. do you think this might be the problem?
bigalk said:
Ive tried everything i can. ALL windows updates installed (along with .net 2.0)
AV disabled
Athenaunlocker added to firewall exceptions - im on a work network so firewall is controlled through group policy - so i cant completely disable. do you think this might be the problem?
Click to expand...
Click to collapse
Hmmm... might be. I'll look into this and see if I can figure anything out.
Oh, by the way, sorry I missed your messages until now. I don't check these forums daily, so if you need to contact me quicker, send a private message to me.
bigalk said:
Hi Zarathustrax,
tried twice and i keep getting error 202 - "check cables....... cannot connect to phone"
I have:
1) connected and synced via active sync
2) set active sync not to sync any items except for files
any ideas?
thanks
Click to expand...
Click to collapse
I've been reading through the forums trying to find an answer... at what point does it show this error? Is it right away? Does the x7501 change screen at all or do anything? I think I remember having problems like this when I unlocked it years ago... but can't remember exactly what I did. Does the x7501 go to it's tricolored bootloader screen at all? It maybe is having problems installing usb drivers while it's in bootloader mode if it changes into bootloader mode when you get that error. Let me know asap so we can get this solved. Also, have you tried using another cable at all?
Putting phone in usb Mode
Try installing Enablerapi.cab before using the olipro unlocker.
Are you still on this
When you run the unlocker there are 3 steps - these are three separate buttons that appear on the flasher each time.
Can you indicate at which step you get this error? Go to this link
http://forum.xda-developers.com/showthread.php?t=378216
...IT IS IN GERMAN...but it gives very nice pics of the process...using google translate you can get some idea. BUT if you can indicate which step you were able to complete.....we can help better !
Also, what windows operating system?
bigalk said:
Ive tried everything i can. ALL windows updates installed (along with .net 2.0)
AV disabled
Athenaunlocker added to firewall exceptions - im on a work network so firewall is controlled through group policy - so i cant completely disable. do you think this might be the problem?
Click to expand...
Click to collapse
chappatti said:
When you run the unlocker there are 3 steps - these are three separate buttons that appear on the flasher each time.
Can you indicate at which step you get this error? Go to this link
http://forum.xda-developers.com/showthread.php?t=378216
...IT IS IN GERMAN...but it gives very nice pics of the process...using google translate you can get some idea. BUT if you can indicate which step you were able to complete.....we can help better !
Also, what windows operating system?
Click to expand...
Click to collapse
I'm kinda thinking he gave up or something.... I've pm'ed him and have been trying to get more info on his problem for a couple weeks. I think he was having the problem on the first step... and the enablerapi will probably solve his problem.
But doing all this reading and trying to solve this problem has got me to pull out my old athena and start playing with it again... it's been a couple years since I've used it... I'm on the HD2 now, dualbooting WP7 and android.... but I've gotten an interest in getting my athena set-up and working again. The athena was way ahead of it's time.... if we could get devs interested in it again and get a good android build ported over, it would make an awesome tablet/phone. I think I'm gonna try to play around with getting android booting on it, but my knowledge of linux and low-level kernel work is limited to none. The best I can do is try to put together a build with what kernels/tools are already out and working on the athena, which isn't much. I think they had it booting and got touch screen working, but not much past that.
Hi zarathustrax,
no i havent given up . was checking in regularly to see if i had any response from you but never even looked at the pms. sorry.
i have a few hours to crack into this now so ive set up on a new machine (different av and firewall) and im going to have a go.
will report back - thanks for all the additional info my man!
al
ok - so i unlocked successfully but i think i may have fcked up. when i read olipros unlocker thread its says that only step 1 is necessary, ("but if you do step 2 you must also do step 3")
as i was trying to get to spl 3.5 i presumed that i didnt need to do step 2 or 3. this might have been a bad choice.
heres what happened:
ran unlocker step 1, it worked, phone rebooted. i finished there as i wasnt sure if i needed step 2 or 3
loaded bootloader screen to check spl. spl said olipro 1.2. i though cool - rebooted phone and now its a black screen. i can get into the bootloader screen whish says:
ATHE100
IPL-V1.00
ATHE100
SPL-V1.20. Olipro
have been reading up on next steps, or how to get rid of blackscreen but no conclusive answer.
its friday so im off home - battle lost but the war aint over!
Well. I'm not an expert (my Ameo was unlocked as I bought it) but if I understand, the black screen is because the ROM on your device dont match the new SPL you have. Try to flash a new ROM (SPL 1.2, right?) should help.
bigalk said:
ok - so i unlocked successfully but i think i may have fcked up. when i read olipros unlocker thread its says that only step 1 is necessary, ("but if you do step 2 you must also do step 3")
as i was trying to get to spl 3.5 i presumed that i didnt need to do step 2 or 3. this might have been a bad choice.
heres what happened:
ran unlocker step 1, it worked, phone rebooted. i finished there as i wasnt sure if i needed step 2 or 3
loaded bootloader screen to check spl. spl said olipro 1.2. i though cool - rebooted phone and now its a black screen. i can get into the bootloader screen whish says:
ATHE100
IPL-V1.00
ATHE100
SPL-V1.20. Olipro
have been reading up on next steps, or how to get rid of blackscreen but no conclusive answer.
its friday so im off home - battle lost but the war aint over!
Click to expand...
Click to collapse
Just replied to your pm before checking this thread, so I see that you can still get to SPL bootloader screen. So, what you should be able to do now is get your phone to bootloader screen and hook it up to pc like that. Then let any drivers that are installing finish, and where it says "serial" at the bottom should change to "USB".
At this point, you can now run a custom rom installer and flash a new rom. Since you want to change to SPL3.5, you should install the Athena Project 4 ROM.
Or if you want to leave it at this SPL for a while and test out a couple WM6.1 ROMS that use this SPL, just flash one of these. Here's a good thread that lists almost every ROM available with links and says what SPL they're for... http://forum.xda-developers.com/showthread.php?t=397518
I'll do a little more research also about the screen not coming on to make sure it's not some other problem, but it probably is just the current rom isn't compatible with the new SPL.
I'm sending this post to your pm too.
Also, make sure you have the SD card and sim card removed when doing flashing. And check what radio you have on your phone... you must have atleast radio 1.50 or higher to use Athena Project 4 or most WM6.1 or WM6.5 ROMS.