strange issues going on.. - 8525, TyTN, MDA Vario II, JasJam Software Upgradin

sorry for dupe thread i put the other one in the wrong section but.. heres the deal
so i almost bricked my device changing the boot screens and was able to recover the device after alot of flashing and finally got black majic to work BUT.. now my storage memory is only 5mb im missing the other 50mb of it.. and then i tried to flash to vp3g's rom but it wont go past the subsplash boot screen so im flashing back to black majic, does anyone have any clue as to why this is happening? im running hardspl7 oilipro 2.10
after flashing back to black majik i have 5.83MB total under storage
total 5.83
used 4.92
free 0.92
ok after flashing to black majik le now it shows
total 11.19
used 4.60
free 6.59
this makes NO sense someone help!
after flashing to black satin my storage only shows 15.05mb
15.05mb
4.42mb
10.63mb
ive tried hard resetting and re-flashing twice now and neither seem to fix the problem.
ok now after flashing to black majik LE
18.32
5.14
13.18
what the hell is going on?!
ok then to normal black majik again..
12.93
5.09
7.84
now after custel ultimate
7.33
5.14
2.19
to make the problems even crazyer when i try to flash RUU_Hermes_CINGULAR_WWE_2.15.502.3_6275_1.40.30.00_108_Ship.exe it flashes just fine ..changes my radio back to 1.40.30 except it wont go past the mainsplash where it lists my radio and gsm

You've probably got a boatload of bad blocks. Good news is that Hard-SPL can likely fix 'em.
HINT: mtty and 'task 2a' will be your new friends soon...

ok please please please tell me how to do this im pulling my hair out u dont even understand.. ive read mrvanx gudies for the past 2hrs..
even tried to flash HERM_DOPODASIA_WWE_3.54.707.3_6275_CustomRUU it wont go past the 2nd splash so then i flashed back to black stain from tri-color and now im showing
17.07
4.76
12.31
i was about to go thru the whole downgrade spl process but can u point me in the right direction for this mtty and task 2a purrty please!

Like VP3G said youve probably filled your device with bad blocks.
put your device into bootloader mode,
run mtty.exe (found HERE) with activesync disabled.
plug in your usb cable.
you should see either USB> or Cmd>
type 'task 2a' then press enter
this will detect and remove ANY bad blocks.
Then reflash a ROM.
If you dont know what im saying to do in this post then i suggest you read the wiki, the hardspl thread and any others regarding bad blocks before you do ANYTHING.

Related

Bricked my phone i think

Hey everyone,
i am so upset and lost; words cannot describe it.
So i installed WM6 black shadow and everything was working except for SMS and MMS. So i am like ok i can live with that for a day till custel' rom will come out. SO i decided to upgrade the radio to 1.43 and boom here is where the problem started, No GSM on boot up. Phone doesn't boot up. I tried install 1.40 over again, still nothing. No i tried upgrade the the rom itself, i tired custel 2.5 and nothing and i tried the new Cingular rom, still same problem. the roms flash all the way. I read the wiki, and saw the mtty.exe thing but that doesn't work for me either. I am really lost and don't know what to do.
Specs
cingular 8525
hardspl v7 cid and sim unlocked.
PLEASE HELP
4.13?? 4.10??
Where did you download these radios from??
or do you mean 1.41 or 1.43??
Yeah thats what i meant, 1.40 and 1.43 sorry. You can see how upset i am.
Thanks Again
Well, if your phone turnes on .. it's not a brick.. lol .. it IS fixable... When you turn the phone on does it go RIGHT to the 3 colored screen?
@dan5.5
You need to read the unbricking thread about this, all the info you need is there.
http://forum.xda-developers.com/showthread.php?t=286755
If you are superCID I don't see how flashing a radio could have messed up your phone.. that's weird.
mrvanx said:
@dan5.5
You need to read the unbricking thread about this, all the info you need is there.
http://forum.xda-developers.com/showthread.php?t=286755
Click to expand...
Click to collapse
I read everything there and nothing seems to be working for me. I woudnt post for nothing. i dont want to be annoying.
OK im going to repost what ive said on 4wm:
We need to check if your Radio BL is functional, firstly leave HardSPL v7 on there and connect to the bootloader via mtty (il assume you know how to do this).
Issue the following commands and tell us the results please:
1) checkimage (this shows the CRC checksums of each component...id expect the radio image to show a timeout....
2) info 2 (This will verify that your CID is intact)
3) info 8 (does a bad block check)
Once youve done this, flash SPL 1.10.oli to the device and once again connect up to mtty.
4) 'rtask a' this will enter the radio bootloader you will see "Enter Radio Bootloader" or something to that effect
from now on when you type the text does NOT appear on the mtty screen.
5) 'rversion' this should return your radio bootloader version...now unfortunatly if you see nothing...you radio BL is dead and sorry your device is royally bricked. If you get something returned back onto the screen (most probably containing the text '0108') then your radio BL is fine.
Click to expand...
Click to collapse
do as instructed in that text, post your results here.
I cant falsh spl 1.10 oli. it gives me the 260 error.
the 260 error is not connected via USB right? .. weird... have you tried taking your battery out for a couple minutes, then booting into BL mode? sounds weird but this worked for me when I didnt flash hardSPL firsl..
hey mrvanx's
I can't downgrade the hardspl to 1.10, anyhelp.
I cant active sync, the phone doesnt boot up.
Is there anyway to aviod having to respond on the phone.
hey,
i can get the phone to boot up into windows and then it freezes within a couple min. what should i do. Still no gsm message and no phone. thanks
Dan
OK, so let's try and get you to a working state - I've bricked mine a couple of times and it can be quite heart-stopping, eh?
The first thing I would do is re-download radio 1.43, just incase your current one is damaged somehow.
Secondly, download Black Shadow - I know it's not the ROM you ultimately want but the aim here is to get you working again and we can move forward from there.
First, boot up into BootLoader mode (hold down the OK button on the left side of the phone and the power button and then press the reset button on the bottom, just in case you didn't know
You should come to the three colour screen and it should be reading IPL-1.04 and SPL-2.10.Olipro. If it isn't, stop here and post what it does say.
If it everything is OK at this point, when you plug your phone into your computer, it should change to USB at the bottom. Just wait for the Found New Hardware prompts to clear on your PC and then flash the black rom - choose the hardspl option in the flash program.
Once that has finished and it is at the "tap screen to set up windows..." bit, put it back into bootloader mode as above and flash the radio.
This should hopefully give you a running phone again as I know this combination works OK as I am currently using it.
Fingers crossed, don't panic, and let us know what the results are
Cheers,
Smiffy.
Nothing is working, can some please help me. Is there anyt way i can restore the spl to the original one so i can send the phone back, i just got it like 2 weeks ago. thanks
Also i have a bad block thats what i think makes the phone freeze after i boot it up.
How can i get around this, thats seems to be the biggest problem.
Hey everyone, let me give you more info.
I can fully flash any rom and and radio,
phone will boot up like 1 out of 10 times and then freezes and thats it.
i have a bad block number 6. I have hard spl v7 installed before the phone got screwed up. I cant downgrader the spl to a lower one to check if radio stack is screwed up. Can someone please help me, if you need to ask me more info feel free.

stuck in boot loader updating to 1.43 on black shadow

I was trying to upgrade to radio v1.43 in the hope that battery life was improved over 1.41 however when it got to 8% it stopped and gave me an error i can't remember After atempting to recover, it got off the three colour screen now the 3100 stalls on the blackshadow version4 screen (bootloader screen?) and goes no further. I tried reflashing but got a 260 and using mtty, only getting 2 com port options, didn't offer any help.
I'm really sorry to have not been able to sort this with reading through the relevant post but I haven't found a solution. What else can I try?
Hi,
Could you pls advise what is your device made, model, SPL version ... etc.
Also did you try to do Hard reset?
I'm using now black MAJIK (and few days ago black shadow) with radio 1.43 with no problem.
its the SPV m3100 When I decided to go Black shadow I read up on mr vanx and made sure I had all the things I needed. If I remember right, when I came to upgrade to Majik the auto detect found the second option down
SPL-1.04/1.10 - 1.09 Bootloader. I've realized since I had a spaz and ran the RUU from the archive this time. From what I've since read thats not too cleaver.
I have tried a hard reset and took the battery out instead of pressing space.
I dont know if this information on the starter screen is of use
M 05
S 04
B 05 D 3lak
I'm not sure, but hard reset doesnt mean you take the batery out.
Please check that link:
http://wiki.xda-developers.com/index.php?pagename=Hermes_For_Beginners#hardreset
I was in your position (hanged on booting) few days ago, and when i did hard reset, it changes every thing to basic normal condition.
i meant when i did a hard reset when it asked me to press space to reboot I took the battery out. I tried again this time pressing space to reboot but I still get stuck on the loading screen. I can't connect by USB to the PC I'm guessing the drivers on the phone haven't loaded and I'm stuck as to what to do.
Does anyone have any ideas?
try look at it http://forum.xda-developers.com/showthread.php?t=286755
ok I've tried everything I can think of to connect the 3100 to the computer so I can reflash it but mtty gives only com 1 and com2 but no USB and neither those two work, active sync wont connect so I disabled it as suggested and running the radio ruu and wrapper wont querry the device. I am now at a loss as to what to do next someone must know what I should do. Please?
what is your SPL?
try this http://wiki.xda-developers.com/index.php?pagename=HTC_Hermes
sl is 1.09 i'd updated it on the previously successful black shadow flash
msn [email protected]
icq 150277111
AIM TazmanFH9
Yahoo bigfathairyboggart
I have tried changing KITL trasport but I am unable to select or chose either option. I have also tried the rversion command in the tri colour screen but nothing happens. I hope I'm missing something nice and simple but I get the feeling I'm not going to be that lucky. Please help
tcSPVm3100 said:
sl is 1.09 i'd updated it on the previously successful black shadow flash
Click to expand...
Click to collapse
I suggest you check again, press and hold the side OK button and the power button...then put the stylus into the hole in the bottom of the unit.
yeah I've done that it's "SPL-1.09"
I had this exact problem yesterday, with the same bootloader too. The phone would not pass the splash and IT refused to upgrade. I ended up downgrading to a shipped wm5 rom (in my case the cingular 1.30.502.1_1.11.00.00) which to my surprise actually worked as no rom radio or spl upgrade moved at al on my phone. Then upgraded back to black majik. I hope this helps.
Thanks. I downloaded the trial of wm5 from the windows website and it asked me to install .NET framework version 1 so I got that but it turns out to be 2.0 not 1.1 It would say it had repaired but it would say this with or without the phone connected.
tcSPVm3100 said:
Thanks. I downloaded the trial of wm5 from the windows website and it asked me to install .NET framework version 1 so I got that but it turns out to be 2.0 not 1.1 It would say it had repaired but it would say this with or without the phone connected.
Click to expand...
Click to collapse
Just download a WM5 ROM from the wiki page!
ok tried this too no luck.
Trying to use the one from orange (linked to through wikki) I get an 294 invalid vendor error however active sync cannot connect yet of course so is this to be expected?
I have however gotten a connection with mtty which is a step forward dunno what to do with it yet though except trying the password 0000000000000000 command but it not disabling the password. This then lead me to read for a further hour how to change it and I've got to be honest; it beat me. I have No idea what the hell its talking about. My head hurt with so much reading.
I get a no gsm pop up v briefly on loader. I so want my phone back
I have since tried CID unlocker just so i get something installed onto this brick but I either get a connection error or it telling me it can't install for some other reason. I can not set the password in mtty to 0000000000000000 so how do I do that and is this the first step to getting things sorted? "just running a rom install" is not happening I can get a USB connection in mtty and that is it. Is the fact i'm running SPL 1.09 a problem? I'm getting precious little help guys If i'm posting in the wrong place or something please let me know. I need thing thing back now. Hours are drifting by with me trying to get some head knowledge but I still need some guidance please
tcSPVm3100 said:
I have since tried CID unlocker just so i get something installed onto this brick but I either get a connection error or it telling me it can't install for some other reason. I can not set the password in mtty to 0000000000000000 so how do I do that and is this the first step to getting things sorted? "just running a rom install" is not happening I can get a USB connection in mtty and that is it. Is the fact i'm running SPL 1.09 a problem? I'm getting precious little help guys If i'm posting in the wrong place or something please let me know. I need thing thing back now. Hours are drifting by with me trying to get some head knowledge but I still need some guidance please
Click to expand...
Click to collapse
can u flashing HARD V7?,i think better u have IPL 1.04 SPL 2.10olipro first ,then try to flashing radio?
and did u try SD card.
In bootloader can anyone here connect with active sync? I can't so updating rom and radio flashes in the usual way isn't possible. Trying the hard spl again it tells me to make sure active sync is connected and as it isn't it throws back a 262 update error. 0% on the hermes and that's currently as far as I can get. I have no means with which to access the memory card.
The reason you get an invalid vendor ID is because your CID doesnt match....download a ROM which is for your device (an orange one?)...then try.
You need to read the wiki alot more before trying anything else since you are not aware of the vendor ID error...nor the fact you MUST use HardSPL.
I linked to the orange ROM from wikki and tried installing it. it was while installing THIS ROM SPV_M3100_ROMUpdate_0407.exe I got invalid vendor error.
Installing a recent DL on HARD spl v7 I get a 240 open file error that's one I haven't had before.
With all other attempts they all say they want an active sync connection.
I can not connect to the phone through active sync
so all attempts by me to flash anything to the phone using an RUU fails.

Bricked phone

I was instaling NBD_v8.3_8MB trough shelltool on my MDA Vario then something happened and my PC restarted I whink it is because of the electicity .... so now when I restardet my phone it is stuck on the T-mobile screen Where it is writen.....
IPL 2.21.001
SPL 2.21.Olip
GSM 02.19.11
OS 6.6.6.666
Thanks in advance
First of all, its not bricked. Bricked = doesn't turn on, nothing, blank screen.
I've looked to your info, you already have HardSPL, so you can flash directly using any RUU, don't use shelltools!
Enter bootloader (hold camera+reset), open up the RUU of the ROM you want (make sure it doesn't have any IPL/SPL) and flash away
well I looked all day what to do and I can not find solution
I just can not understand how to flash the phone
I found one solution via some kind of Wizard_love, but again I do not know what to do
Please help i am haveing the same thing just did it today i have the Cingular 8125....i have held camera+reset and got into these Red,Green,Blue,white screen and it says IPL 2.25 and SPL 2.25 now when i run the ROMUpdateUtility_Wizard_NoID it does not work i have my usb pluged in and my phone says USB please help
Thank you
PS.
I am running Vista
IPL 2.25
SPL 2.25
GSM 02.25.11
OS.6.6.6.666
_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-
Ok i have try everything. I have tried the RUU from the HTC site and even everything else when it is searching for the PDA and crashes idk why. I turn on my phone holding the camera and i get to the Red,Green,Blue,White...Plug the USB in and the phone says USB but not my computer??? so i don't know what i need to do please HELP i just got the phone and read you can do all this stuff
1. Please use a PC with Windows XP
2. Download your original carrier ROM (i.e. Cinglular stock ROM) and flash back to original WM5
3. Install HardSPL or use SSPL
4. Flash to WM6
starkwong said:
1. Please use a PC with Windows XP
2. Download your original carrier ROM (i.e. Cinglular stock ROM) and flash back to original WM5
3. Install HardSPL or use SSPL
4. Flash to WM6
Click to expand...
Click to collapse
Were can i get HardSPL,SSPLand the flash back up?
all i have is the original rom
You guys wanna see bricked? I have a BRICKED! phone... My MDA was the unfortunate victim of a car accident. When my car went carreening off the road, my MDA went flying through the air and ended up on the floor of the car but not before hitting virtually every surface on the inside of the car.
Now my charge port is completely snapped off and my battery shorted out when I was trying to hold the charge port in place to charge it and fried the main board. DEAD. NO MORE.
THAT MY FRIENDS, IS BRICKED....
No worries though, I already ordered a TyTN II
Cool can you help?
Oh and i had the same problem with my mda and i got it replaced from tmobile. - the easiest way to reapair an MDA is getting it replaced ^^
offtopic
@dharvey4651
Why didn't you buckle up your phone?
Well i got mine up and running agian just used XP and install the RUU from HTC YES.......Now when i go to install WM6 when i press update were it should show me the Ver. of the one i am installing on my phone it does not say why please help and what do i need to install WM6 on my phone?
Just a quick question did you read the other threads there are already. They basicly explain everything clear and good
i have just still stuck on some stuff
dferreira said:
First of all, its not bricked. Bricked = doesn't turn on, nothing, blank screen.
I've looked to your info, you already have HardSPL, so you can flash directly using any RUU, don't use shelltools!
Enter bootloader (hold camera+reset), open up the RUU of the ROM you want (make sure it doesn't have any IPL/SPL) and flash away
Click to expand...
Click to collapse
jukata
first of all,as dferreira has assured u that ur device is not bricked,secondly ,you already have HardSPL,that means your device is unlocked,just follow his instructions,download any wm6 Rom and flash,it'll good to go,but if u still want to be sure,download WST Tool from the below given thread read carefully and apply the tool to verify the status of ur device,
http://forum.xda-developers.com/showthread.php?t=329170
u can flash NBD rom which u have or any other wm6 rom,goodluck
NVM i am on the Other Page! Thanks
Ok, i have read everywhere and can't help myself, so if someone would be kind enough to help it would be much appreciated
Ok, Used SoftSPL and tried flashing the ROM. It manages to get to 99% and then just goes RED. I have tried 3 different ROMS and same story it goes RED at 99%.
When i remove the battery, it goes to the RUU Red, Green and Blue screen. SPL version is 2.16.0001. Not Oli's new one.
What do i do from now?
kastro said:
Ok, i have read everywhere and can't help myself, so if someone would be kind enough to help it would be much appreciated
Ok, Used SoftSPL and tried flashing the ROM. It manages to get to 99% and then just goes RED. I have tried 3 different ROMS and same story it goes RED at 99%.
When i remove the battery, it goes to the RUU Red, Green and Blue screen. SPL version is 2.16.0001. Not Oli's new one.
What do i do from now?
Click to expand...
Click to collapse
Soft SPL only allows you ONE update, so phone is CID unlocked only when Soft SPL is loaded.
It's normal for the RUU to stick on 99 % for a couple of minutes, The whole update will take aprox 10 minutes.
You can try the hard SPL from there you are semi-permanently CID unlocked.
Good luck,
EquinoXe

Stuck on Flash Screen please help

hey guys im sorry i know there is a page for this in the wiki but i read it and there is no mention of my spl (2.07.0000)
my phone is the sprint version of the titan the mogule
so i got stuck when i tried flashing from dcd's latest rom 3.2.3 to the new sprint 6.1 as i understand it i was supoosed to relock the device so i did using the titan_relocker file. every thing seemed good so i tried to install the new rom 3.56.651.0_RS_TITAN_3.42.02_SPCS2.04_PPST_0718_Ship and it acts a little weird the load bar shows up on the computer and then about a half a minute later on the screen of the phone it loaded up to about 8 percent or so and then gave an error and some recovery steps that didnt do any thing.
so now im stuck in the flash scren and i have tried flashing a bunch of roms
an old stock sprint rom
the spritn 6.1 i mentioned earlier
and then dcd's 3.2.3 (this one dose not do the strange thing where the load bar shows up on the computer first then the phone but it still does not work)
and nothing works. i cant find any mention of my spl 2.07 and i dont know how it got on my device. as i understand it your phone has to boot up to be able to put a new spl on there so im at a loss if any one could help i would be very greatful.
im new to the 8900 so i dono who the gurus are around here i was a tilt and hermes guy so i dont even know who to ask.
dang i have a theory i think i may have only goten to the step where it flashes like a temp spl on to the device on the relock?... that sould right to any one?/ slash know how to fix it
edit: cant re-run the relock app it crahses and goes to the recovery steps before hitting 1 percent

Tried approximately everything to make my tytn's radio work

So here i am with situation : i can put just about any rom to my tytn, but the problem is the radio. I have tried god knows how many different radio updates, none of em work. And "work" as in when i start the updater, the percentage stays at 0% and after a minute or two it just says error code 260. Im using my _xp_ laptop to update it, with usb-cable. No, i dont have micro-sd card cause im totally broke :<
So i got this tytn from my friend, for free, it originally contained black satin and yes everything worked. But then i installed hmm, yes, CRCs newest and thats the point it went kaput, the radio i mean.
The information that the magical tricolor gives me is:
HERM200
IPL-1.01
HERM200
SPL-1.40.Olipro
So any advice, im puzzled, searched the forums x^y times.
halp! :<
You don't have Hard SPL V7 installed - SPL = 2.10 oli. I'd install that 1st.
Look, $10 for a 2Gb sd card, surely you can afford that?
Don't get bigger than 2Gb if you want to use the sd card method as bootloader won't recognise it. I use a 256Mb for flashing and an 8Gb for normal use. More than enough...
Go to the Hard SPL thread to find out how to install Hard SPL using the sd card method - page 116, post 1160. Afterwards you can use this method to flash roms, just drop the steps using SSPL.exe (Soft SPL). I wouldn't chance flashing a radio rom using the pc, too many things could go wrong... Once the memory is corrupted, you have a lovely PDA, but no more phone...
Also, try to flash the original radio rom on, it may work, DON'T try flashing other things as you may permanently brick your Hermes...
Cheers...
yeah looks like im going to have to submit to buying that micro-sd after all, ill get it, do some things and report back
thanks for advice
now back to the drawing board ^^->
new developments :
installed hard-spl 7
bought micro-sd card, formatted it to fat32
attempted, or, attemping, as i write, to put in a new radio rom as instructed in page 116 post #1160
the progress bar gets stuck to ~10% and never goes forward
what course of action to take next?
yup, waited ~50 minutes, still stuck at 10% :<
Try the SHIPPED STOCK radio ROM... If you can remember what it is...
People have had success flashing the native raio rom when none other will work. It seems it hasn't got to the "magic" 12% mark where its impossible to recover so you MAY be able to flash, no guarantees as these little buggers can be obstinate and cantankerous...
now am i blind but, where to get this magigal stock radio rom ?
pikkuhukka said:
now am i blind but, where to get this magigal stock radio rom ?
Click to expand...
Click to collapse
The operator ROMs typically include radio too. You could look for them.
I have a bricked Hermes. Have tried all the things that you have, and some - no luck in getting the radio to work. The PDA part works beautifully. And the battery lasts almost forever...
kernelguy
I live in finland so um, i have no idea what _is_ the original rom, ohwell :<
brick is a brick
btw got a perfectly working tytn ii so no worries ^^ not gonna flash it in _any_ way x)

Categories

Resources