Upgrade Softbank X01HT to WM6 - 8525, TyTN, MDA Vario II, JasJam Software Upgradin

Please find below the infomation of my softbank X01HT which I bought few days ago. The softbank has been unlocked by the shop and is running traditional Chinese on WM5.
IPL 1.01
SPL 1.09
ROM Ver 1.23.708.4
ROM Date 07/24/06
Radio 1.06.00.10
Comm Protocol 32.37.7010.01W
Please advise if it is safe to run HARDSPL for upgrading to WM6.
Will there be any adverse/damaging effect?
Do I need to downgrade the ROM version before running HARDSPL V7.
Please advise the procedure.
Thank you in advance
Ken
Isi

I believe you can just put it into bootloader mode and flash the WM6 Dopod ROM. A friend of mine did this recently.

i hv just done it. i did not encounter any major problem except after flashing it with the official ROM, the storage memory is very low ....

KENPPCPHONE said:
Please find below the infomation of my softbank X01HT which I bought few days ago. The softbank has been unlocked by the shop and is running traditional Chinese on WM5.
IPL 1.01
SPL 1.09
ROM Ver 1.23.708.4
ROM Date 07/24/06
Radio 1.06.00.10
Comm Protocol 32.37.7010.01W
Please advise if it is safe to run HARDSPL for upgrading to WM6.
Will there be any adverse/damaging effect?
Do I need to downgrade the ROM version before running HARDSPL V7.
Please advise the procedure.
Thank you in advance
Ken
Isi
Click to expand...
Click to collapse
yes it is safe... but you need an activesync partner ship setup to installl HardSPL as it needs to push SSPL to your device... for more information read www.mrvanx.org

Zilch said:
I believe you can just put it into bootloader mode and flash the WM6 Dopod ROM. A friend of mine did this recently.
Click to expand...
Click to collapse
with updating/installing HardSPL the device needs to be in Windows with activesync connected so SSPL can be pushed to the device...

I trid to install HardSPL Version 7 (2.10.olipro).
I activesync connected and run RUUWraper.exe
I go through all the selection right and on the last page after I click "next" I press yes on my Softbank. but the flash download didn't started and the Softbank reset and go into the engineering mode where I still see :
IPL- SSPL Des
SPL-1.09.ds
All my versions are the same as Ken which are:
IPL 1.01
SPL 1.09
ROM Ver 1.23.708.4
ROM Date 07/24/06
Radio 1.06.00.10
Comm Protocol 32.37.7010.01W
Could anyone advise any solution in proceed with HardSPL installation?
Thanks a lot
Henry

Hi Conorau,
Following the procedure in this forum, my softbank successfully upgrade to WM6 without any problem. Good luck
Ken
IPL 1.04
SPL 2.10.01 olipro
ROM Ver 3.54.708.2
ROM Date 07/05/07
Radio 1.47.00.10
Comm Protocol 32.80.7020.20H

here is solution
I think it usefull !
http://bestsolution.spaces.live.com/Blog/cns!E39312F16E0FBE41!728.entry
and more infomation http://forum.xda-developers.com/forumdisplay.php?f=355

KEN can you tell me exectly what you did? i also want to upgrade my phone

is it ok for my phone to to according to this FAQhttp://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeGuide + take this ROM http://forum.xda-developers.com/showthread.php?t=321332
please help!

Related

Dumping SPL/IPL...

Guys, how do I dump the SPL, IPL, Bootloader, radio ROM and Radio bootloader version?
I will use the unlocker to unlock the TYTN but then I want to roll back to the default version numbers that I have. I dont want it to stay with the HardSPL or with the newer Radio.
Thanks
Have you ever try to use the search function first? ...or just read the Wiki?...here are the how to...but next time read the wiki first!
Regards,
Primoz
Guys, it starting to get boring.
On every question asked, you send to RTFM.
Maybe, just MAYBE, I already READ everything and I STILL (!!!) have a question? Maybe I'm not as stupid as you think? Maybe the guides are NOT (?!?!!) 100% perfect?
To the subject; I did dumo the ROM. However, as I understand (FROM the guide), it DID NOT dump the SPL and the radio (or the bootloader and the Radio bootloader).
Please confirm that it DID extract everything and that if I'll burn it back to the device it will be 100% the same as it now.
Also, if I first use the unlocker, and then burn back the original radio, will it get locked again?
knfevg said:
Guys, how do I dump the SPL, IPL, Bootloader, radio ROM and Radio bootloader version?
Click to expand...
Click to collapse
You don't need to dump that, every version is available as a shipped upgrade so you can extract it from there and flash it later if you need it for warranty reasons.
knfevg said:
I will use the unlocker to unlock the TYTN but then I want to roll back to the default version numbers that I have. I dont want it to stay with the HardSPL or with the newer Radio.
Click to expand...
Click to collapse
Most probably your rom is available as a shipped NBH, just flashing it will lead your device to the original rom. The only thing you can't do is go from htc_boot 0108 to htc_boot 0106, so make sure you don't upgrade to a very new radio if you want to be able to go back to your original radio if it has a 0106 radio bootloader.
knfevg said:
To the subject; I did dumo the ROM. However, as I understand (FROM the guide), it DID NOT dump the SPL and the radio (or the bootloader and the Radio bootloader).
Click to expand...
Click to collapse
Following the guide, you've only dumped the OS part of the rom.
knfevg said:
Please confirm that it DID extract everything and that if I'll burn it back to the device it will be 100% the same as it now.
Click to expand...
Click to collapse
Tell us how it is now.
knfevg said:
Also, if I first use the unlocker, and then burn back the original radio, will it get locked again?
Click to expand...
Click to collapse
no.
POF, you are THE GOD!!! Thanks, finally someone HELPS!!
Ok, here are the clarifications:
1. How do I check the htc_boot version? I have the 106 SPL so I can’t launch the Radio loader from there....
2. If I dumped only the OS part I guess I should dump the rest too. How do I do that and how do I make the "burnable" afterwards?
3. Here is the current "setup":
The device is Orange branded. It’s exactly as described under "Hermes versions" in Wiki for Orange-Israel:
Israel Versions
HERM200 Orange IL HTC TyTN Israel QWERTY Locked OS 5.1.195 (Build 14955.2.3.0) 1.18.255.3 07/22/06 WWE 1.18.255.112 1.03.03.10 32.34.7010.01H
The SPL is 1.06 and IPL is 1.01. I have no idea how to check the HTC_BOOT version.
There is an Orange boot logo.
Guess that is. Thanks once again
knfevg said:
1. How do I check the htc_boot version? I have the 106 SPL so I can’t launch the Radio loader from there....
Click to expand...
Click to collapse
You should use a SPL based on 1.01 or 1.04 to use 'rtask' and access the radio, you can either flash it or use SSPL to load the NB without flashing. Anyway you don't need to do that, radio 1.03.03.10 has htc_boot 0106.
knfevg said:
2. If I dumped only the OS part I guess I should dump the rest too. How do I do that and how do I make the "burnable" afterwards?
Click to expand...
Click to collapse
You don't need to dump the rest. See later.
knfevg said:
3. Here is the current "setup":
HERM200 Orange IL HTC TyTN Israel QWERTY Locked OS 5.1.195 (Build 14955.2.3.0) 1.18.255.3 07/22/06 WWE 1.18.255.112 1.03.03.10 32.34.7010.01H
The SPL is 1.06 and IPL is 1.01.
There is an Orange boot logo.
Click to expand...
Click to collapse
A full shipped NBH consists on 7 parts: IPL, SPL, MainSplash, SubSplash, Radio, ExtROM and OS.
See the hermes shipped upgrades wiki page. Use nbhextract to separate the NBH into rom parts.
Download any orange ROM to get your MainSplash.nb & SubSplash.nb (boot logo as you say).
Download any rom with IPL-1.01 & SPL-1.06 to get IPL.nb & SPL.nb
Download any rom with radio 1.03.03.10 to get GSM.nb
Unhide your ExtROM to get the files in Extended ROM, then create ExtROM.nb using ExtROM image editor.
Reconstruct the OS.nb using the instructions on wiki (see trinity wiki also)
Finally, create a NBH using nbhgen, and package it with CustomRUU to be able to flash it pushing SSPL.
Make sure you don't upgrade to any radio with htc_boot 0108, otherwise you'll never be able to flash your original radio again.
Hope it's clear
Thanks POF. PERFECT!!!!
Maybe a Wiki should be made for this as I notice alot of people asking on how to go back to the original state of their device?
tnx in advance
sir POF i did want to get the original state of my device for warranty purpose..
I tried everything i can.. i read a lot.. still confusing me.. I did encountered No GSM, the phone dont boot..
I run WM6 Cooked rom before..
heres my device now...
Dopod 838 pro Asia
ORIGINAL
ROM 1.23.707.4
07/21/06 WM5
RADIO 1.06.00.10
PROTOCOL 32.37.7010.01H
OS BUILD 14955.2.3.0
AKU 2.3
SPL 1.04
HTC BOOT 106
IPL ?
NOW RUNNING
WM5
ROM 1.23.707.4
07/21/06
RADIO 1.40.30.00
32.73.7020.16H
OS BUILD 14955.2.3.0
SPL OLIPRO 2.10
IPL 1.04
AKU ?
HTC BOOT ? dnt know if it changed
Ive read ur message.. I just want a simple question...
BASED on the data above is it possible to bring back the device on its
original state specially the radio and SPL ?
TNX in advance..
Im willing to research again if yes..
I have SPL - 2.10 Olipro. I am trying the various Boot Roms starting from 1.41 backwards as someone recommended in some other thread.
But I need to run SSPL before or I get an Error why does that happen why can't the SSPL of the ROM upgrade check and do the needful.
Secondly I want to revert back to SPL-1.04 or 1.09 is it possible. If yes please tell me how. If it is detailed in some other thread please tell me the thread details and oblige.
THANKS IN ADVANCE.
tonetagabaler said:
BASED on the data above is it possible to bring back the device on its original state specially the radio and SPL ?
Click to expand...
Click to collapse
Radio no (you cant go back from htc_boot 0108 to 0106), SPL and rest of rom parts yes, it's possible to return to original state.
hsanghavi said:
I want to revert back to SPL-1.04 or 1.09 is it possible. If yes please tell me how. If it is detailed in some other thread please tell me the thread details and oblige.
Click to expand...
Click to collapse
Read the HardSPL sticky thread.
I tired but could not locate the Hard SPL thread can you please tell me where to find it.
THANKS.

Downgrade to WM5 Asia ROM problem

Dear all,
I was upgraded my Prophet to WM6 b4 version,
and I want to downgrade my phone to WM5 Asia version now.
But the process is terminated at 95%.
I think that there maybe SPL version problem. The version number of SPL is 2.15.0000 before, and now is 2.20.0000
Is it possible to making a custom asia rom (nk.nbf) with SPL version 2.20.0000 by myself?
Anybody can tell me how to getting start and what's the tool I need to have?
Thank you very very much and sorry for pool english.

Downgrade for warranty reasons !

Hi guys I need to downgrade for warranty reasons (Vibrate stopped working)
I have been looking through mrvanx guide and it mentions
"SPL 1.04 (includes IPL 1.00) SPL 1.06 (includes IPL 1.01)"
The thing is my SPL was 1.04 and IPL 1.01 which seems to be a mix of the above !
my Radio version 1.05.05.00 but this is also not on the wiki.
Here are my phone details before
IPL-1.01
SPL-1.04
Rom version 1.21.110.3
Rom date 06/19/06
Radio version 1.05.05.00
protocol version 32.36.7010.04H
Will I need to get the exact same radio and rom version with rom date
or you think its possible they will over look these details aslong as WM5 and an early radio rom is flashed?
Thanks for any advice, Chris.
I really doubt that they would catch it as long as you have wm5. But, if they do, then just play dumb or try another store.
Thanks, I'll try that is there any risks when downgrading or uninstall HardSPL v7 ?
Once my phone had SPL 1.04 on it (after downgrading via MrVanx's method), I flashed the official rom from my carrier, and it returned me to the factory settings. One note, my phone is super CID.
The only T Mobile WM5 rom I can see is the Hungarian one in this thread http://forum.xda-developers.com/showthread.php?t=287338
will this one be ok for t mobile uk ?
The one from hungary is the only t-mob WM5 i know of. You can also search for a dumped one and reconstruct it.
one note: do not flash radio with htc_boot less than 0107 or you'll brick it, as for your signature you have htc_boot 0108 now.
pof said:
The one from hungary is the only t-mob WM5 i know of. You can also search for a dumped one and reconstruct it.
one note: do not flash radio with htc_boot less than 0107 or you'll brick it, as for your signature you have htc_boot 0108 now.
Click to expand...
Click to collapse
Thanks for the advice I will deffentley do alot of reading before I downgrade.
So htc_boot less than 0107, does that mean 0107 are ok nothing lower or stick with htc_boot 0108 ?
I have no idea how to reconstruct a dumped rom so ill have to flash the hungay one.
0107 is ok, but nothing lower. To reconstruct a dumped rom, read the wiki

HardSPL how to

Hi everybody.
I'm about to upgrade my O2 XDA G4 from WM5 to WM6. I bought this neo on ebay and I don't know if it has already been HardSPled. Is there any chance to know - or - can the HardSPL procedure run again without creating problems?
Are the Radio, the IPL and SPL upgraded as well using one of the last WM6 rom or they should be upgraded manually? Do you recommend to upgrade also IPL/SPL/Radio?
Many thanks
The way to tell if it has been HardSPLed is to see the SPL number.
if it is 2.G3.4PDA or 2.G4.4PDA it has been hard SPLed if not, you will need to do it.
Generally, radio ROMs and IPL/SPL are best left alone (other than SPL for HardSPL).
Thanks for your quick quick reply. I have the following numbers:
IPL 2.15.001
SPL 2.15.001
GSM 02.30.21
OS 2.13.9.21 ITA
So I think I have a "2.G4.4PDA". BTW, while I can understand what 2.G4 means, I have no clue about 4PDA... Can you help?
Thanks again
D.
The numbers themselves (2.G4.4PDA) are meaningless... I think it is 2 (the SPL version) G4 (the device version) 4PDA (sounds like "for PDA").
You will need to HardSPL first, using G4 HardSPL as your device is a G4, then you can flash a ROM.
Done.
Thanks for your support. Now I have the following:
IPL 2.15.001
SPL 2.G4.4PDA
GSM 02.30.21
OS 2.13.9.21 ITA
Now you can flash a ROM.

update x7500 problems

hi friends
when I try to update my pocket pc to wm6.1 spl 1.2 or flash spl whit athena unlocker it breaks at 1% during the flash and dont let me to unlock it or upgrade it what can do please help me
thanks alot before for your helpful information
my phone information
wm5
spl 1.07
rom version 1.25.409.2
radio version 1.38.00

Categories

Resources