i tried to install the latest At&t ROM and i got an error asked me to try and recover it but when i try to recover it it still give me an error message and now my phone is stuck on the bootloader screen it says IPL-1.00 SPL-1.40.Olipro can someone please help me get this out of bootloader mode...i tried reseting it or tried other ROM's but nothing will work....TIA
i can't even get my pc to recongnize that my 8525 is connected to the USB port....
EDIT: I got my PC to see my 8525 by unchecking the USB connections in ActiveSync....
I think this is a crosspost from the HardSPL receovery thread, so I will just answer it here.
Manually put phone in bootloader mode.
Plug into USB
Run RUU to start ROM install
Manaually select your SPL version
Ignore warning in red letters on next screen
Flash away.
(Do not mix up the first two steps - put in bootloader, THEN plug into USB)
If this does not not work, use SD Card flashing method.
Well I was trying to upgrade mt niki to 6.1 but apparently I must have missed a step or did something I shouldt have and now I am stuck with the color bar screen. Can anything be done? I am running Vista.
tri-colour = Bootloader
The tri colour screen is the boot loader screen, when you updated, did the progress bar go allll the way to 100%?
If so, its in bootloader, try to flash another rom from you computer,
Also run through what you done to update - What rom also. Did you hard-spl, Uspl or anything like that?
It stopped at 15%. These are the directions I was following:
Originally Posted by Judge584
Follow these steps:
1. download the attached files (flash-uspl-niki.zip & sspl-1.16-nike)
2. REMOVE SIM and SD CARDS !!
3. connect usb cable
4. copy sspl-1.16-nike.exe to your device and run it (usb cable must be connected!)
5. after a few seconds "USB" appears on the display
6. unplug and replug the usb cable
8. you can now flash the uspl by running ROMUpdateUtility.exe from flash-uspl-niki
9. Now you can flash the latest rom update to have spl 1.22 and wm6.1.
ouch, Thats the only problem with sspl,
urmm.
How long did it stay at 15%?
As the device isn't CID unlocked you can only flash official roms...
Find an official rom, in the bootloader connect the USB and see if it will flash. It should do!
fingers crossed..
the only rom I can find for singtel in singapore is an updated one so I am trying that now so far so good, I am at 30%. So if this will get me going again can you offer a little advice or explination as to your last post, how do I go about loading a newer 6.1 rom on my device?
Of course, thats what these forums are for. The singapore rom shouldn't hassle you tooo much if you know your way around Windows mob well enough. Let me know how it goes and i'll help you through..
Deejaynate said:
Of course, thats what these forums are for. The singapore rom shouldn't hassle you tooo much if you know your way around Windows mob well enough. Let me know how it goes and i'll help you through..
Click to expand...
Click to collapse
well i was able to fix it by using the singtel rom. I want to use the Niki SuperCID unlocker but I have to install the " HardSPL 1.15 MFG " first - can you walk mw through this so I dont brick my touch again. do you have messenger?
yeah Windows live messenger, add me [email protected]
sorry to hijack your thread, but I encountered exactly the same thing. The screen is now stuck with 3 colour bands. I tried to flash it with an official rom, but the computer is not connecting with the phone, active sync does not recognise the device, any help!?
this is what I did:
1. download the attached files
2. REMOVE SIM and SD CARDS !!
3. connect usb cable
4. copy sspl-1.16-nike.exe to your device and run it (usb cable must be connected!)
5. after a few seconds "USB" appears on the display
6. unplug and replug the usb cable
8. running ROMUpdateUtility.exe from flash-uspl-niki
Sorry for the non prompt reply
I have been at work alot lately,
sorry for a non prompt reply.
Active sync wont connect to your phone, as its in bootloader mode.
At the tri-colour screen, does you computer beep when you connect it, or try to install drivers?
thanks for replying!
no beep from the computer, when connecting the usb to the phone, the phone changes from "serial" to "usb".
I tried reflashing with ROMUpdateUtility.exe from flash-uspl-niki, it will work, but says fail and will go into recovery mode. It will then complete the "recovery" action and go back to flashing new rom which won't work.......
The same ocurred with me!! Help me!
In the middle of an unlocking process, somehow(in the flashing radio process,i got 100%, and then a message saying: an writing error ocurred). So my htc dual got with the image NIKI200 (and four colour - red,green,blue and white..). Now i tried hard reset and after i presse send to initialize, the phone goes to that bloody image....i cant do nothing....what should i do? help me please....regards
luismatos123 said:
In the middle of an unlocking process, somehow(in the flashing radio process,i got 100%, and then a message saying: an writing error ocurred). So my htc dual got with the image NIKI200 (and four colour - red,green,blue and white..). Now i tried hard reset and after i presse send to initialize, the phone goes to that bloody image....i cant do nothing....what should i do? help me please....regards
Click to expand...
Click to collapse
You need to flash an original ROM from your service provider (phone company).
I am trying to flash from the bootloader to recover from an installation error on my Fuze. I've entered into the tricolor bootloader screen by holding down Vol.down and reset. Now, when I plug the phone into the computer, the computer recognize the phone as a Qaulcomm CDMA Technologies MSM, and is trying to install a driver for it (which it cannot find.) When I run the Custom_RUU, it does not find my Fuze and is showing a ERROR[260]: Connection.
What am I doing wrong? Do I need to find a driver for Qualcomm first? I searched, and it seemed that when you enter bootloader to flash, it is suppose to say USB at the bottom. Mine says Serial. Does that matter?
If more information is needed to troubleshoot:
SPL is SPL-1.90.OliNex
Phone is unlocked by using Olinex's unlocker
Rom was EnergyRom 3.0 Phoenix 51909
Problem was caused because I tried to install Studio Kuma Traditional Chinese Fonts on it. That program works flawlessly on a WM6.1. Of course, Energy 3.0 are WM6.5, hence causing the problem.
Any assistance is very appreciated.
Try sd card flashing
You have connect your device to your USB port and let it find the drivers. In order for it to download the drivers, you must have Activesync or Windows Mobile Device Center.
Once you have one of those downloaded, launch it and connect the device while it is running normally. Opt to connect via Activesync on your phone. You don't have to have these running in the future but you need it to find the drivers and install them. Leave the Activesync connection intact while you run the Flash program.
Once the phone reboots in bootloader mode, the PC will probably download some more drivers. The Flasher will probably time out while the drivers are being downloaded and installed. Keep trying.
Once the bootloader drivers are downloaded and installed, try to run the Flasher program again. Sometimes you'll need a reboot if something is hung up.
You SHOULD be able to reboot, put the phone in bootloader mode (Down + Power + Reset) and it should change "SERIAL" into "USB". Once it displays "USB" you are good to go. Load up the Flasher program and it should go all the way through without the assistance of ActiveSync or Mobile Device Center.
I always flash in bootloader mode, I just know the initial pairing is rough.
Well, I flashed from sd card, and the phone is working now. Thanks for everyone's replies.
Hey guys,
So I wanted to try out the newest CM12 ROM with A5.0 but seems like it didnt exactly happen how I wanted it. Rooting the device and then installing the XZDualRecovery without a problem. Then downloaded the ROM and gapps.
I have SGP311 (pollux_windy) so I downloaded that version of the CM12 at first. It said that my device is pollux, which I ofc was dumb enough to just skip and download the pollux ver and then install that one. So I installed the pollux ver instead of pollux_windy and when I hit restart device I didnt see it boot again.
So I wanted to connect it to my PC, PC didnt recognize it ofc. Only way my PC regonizes my tab is by fastboot mode. I had to install a driver for that. And even then only the Sony Mobile Flasher by Androxyde recognised it. I run into bootloop various times before with my tab and Emma always fixed it but thats unfortunately not the case here as Emma doesnt recognise it either :/
So now here's the problem, I can only do fastboot mode (not flashmode) and the only program able to do sth with my device is this Sony Mobile Flasher. I downloaded a official FW there and wanted to install it but it required me to go into the flashmode which I can't.
Is there sth I can do? The only thing working is the LED and fastboot mode.
Is there a way to put the device into flashmode via PC, that would solve all issues or maybe a trick to go into flashmode? As there was some thread about it but the thing they did didnt work for me :/
Please help
Thanks in advance
Nevermind, I just forgot how to use Emma....
For anyone to whom this happens:
Computer: Open Emma from the Start menu of your computer.
Connect a USB cable to your computer.
Phone: Turn off your tab.
Connect your tab to the USB cable while holding the VOLUME DOWN.
Computer: Select the software you want to flash in the Service list. The tool automatically detects the tab and lists available software versions, which are called Services in this flash tool.
Click on Apply Service. The tab will now be flashed.
Phone: When you have flashed your device, you can disconnect your phone from the computer. The first time you start your device after you have flashed it, the boot-up might take a little longer than normal.
Hey, I am new here so sorry if I'm posting in wrong board.
I rooted my P70 a while ago and everything was fine. Now I decided that I want to flash 5.1.1 on it. I proceeded to flash TWRP.
I tried it with SP flash on pc, I checked that my scatter file and recovery.img was correct. I opened the scatter file in SP, connected my phone and clicked download, but nothing happened. Only the phone started charging, I have enabled USB Debugging and developer mode. The bootloader was still the stock one. Why?
Next thing I tried is to put the recovery.img on SD card and downloading Uncletools, I flashed it and it asked me if I want to reboot in bootloader, so I did, but it was still the stock bootloader.
What am I doing wrong? Thanks a lot for any response.
Anyone got any idea?
Click download and conecting usb cable to hh
Hey,
I have the same issue. The phone is rooted but the SP flash tool will not do anything. I've read that it's because the USB drivers are incorrect. However I am unable to install the drivers as the phone does not show up under other devices but rather under portable devices. I tried to install the android sdk and use those drivers or ones I found on the web but none of them will take. I found the ADB device signed driver under USB devices in the device manager.
I am honestly at a loss here. Would be grateful if anyone has ideas I could try!
Thanks