Hi there!
I'm new to this : since i upgraded to the offical rom by HTC to wm6 and downgraded the radio rom to 1.40.30.00 to be able recieving calls, now the gsm and gprs are working fine but impossible to connect to wifis ...
Is there any relation between the radio rom and wifi ?
thanks for your help!
CJ
Are you able to connect to wifi but unable to use any internet apps (Poket IE) If so you will likely need to go to programs/proxy manager and disable the proxy. If can't actually connect (The wifi tower doesn't show the connection arrows) then I'm not sure... Hope this helps.
DeathsPal
Thanks but my pocket IE is working fine, and the wifi tower arrows are in movement but not stopping!
CJ
My 838 had the same problem too after i upgraded to WM6 . Whenever i try to enable the Wifi the arrow spinned and then stopped without any message. But it was impossible to enable it. Any help??
upgrading your radio has nothing to do with wifi connection... Does that wifi connection require a WAP of some sort?
I just found out that by putting off the gsm, the wifi connects with no problem, but impossible with the gsm on !
CJ
I get wifi working with gsm on.
see
http://forum.xda-developers.com/showpost.php?p=1457932&postcount=14
Curious Jack said:
Hi there!
I'm new to this : since i upgraded to the offical rom by HTC to wm6 and downgraded the radio rom to 1.40.30.00 to be able recieving calls, now the gsm and gprs are working fine but impossible to connect to wifis ...
Is there any relation between the radio rom and wifi ?
thanks for your help!
CJ
Click to expand...
Click to collapse
try downloading proxy manager.cab from the internet.
open the program and disable proxy. this worked for me
For other WiFi dead problems, check out this thread:
http://forum.xda-developers.com/showthread.php?t=322225
Related
hi could someone plse help i installed wm6 on my ameo the t mobile friendly rom but now i cant get a fix on my wifi ive got a belkin n1 router i know thats working because my universal works fine. i also tried pocket hack master to try and slow down the cpu on the ameo becase i found it in another forum but still could not get it to work. any suggestions plse .thanks in advance
Does the WiFi light flash when you switch WiFi on?
Do you have the latest radio rom (1.45.00)?
Can you ad-hoc WiFi between your Athena and Universal?
Have you tried looking for updated firmware for your Belkin?
The only reason I ask, is because I couldn't connect to my WiFi network either but my Universal could too. Did all of the above and it works fine now
hey yoor right the wifi light isnt flashing wat to do. pleasse post have to go will try wen i get back thanks
The first thing I would do is flash the radio Rom to 1.45.00.
http://forum.xda-developers.com/showthread.php?t=319993&highlight=radio
still not working
hi tried everything you guys suggested but no luck also tried flasing all the roms i could find with no luck can somone post me a link please who has a t mobile ameo of the rom they are using and wifi is working properly.thanks in advance
If you have re-flashed the Radio rom and WiFi still doesn't work, I would say your device is faulty. Send it back for repair.
if this is the case anybody know where i can get the t mobile rom from for waranty.thanks
In the Members FTP area
got the light to flash but still it tries to connect but no luck the one on the ftp sight is german rom or am i looking in the wrong place.ok tried the ameo at me cousins and it works fine his hermes wont work at mine my unieversal does so does my psp so its goto to be a isue with my belkin n1 router.he has a belkin pre n g + and all our phones are working fine on it. what do you guys sugest
Belkin & wm6
Hi,
I'm also suffering from this issue. Please assist before I'm forced to revert back to a previous unit and suffer all the associated reconfiguring...yawn. Whats the issue?
moh6299 said:
got the light to flash but still it tries to connect but no luck the one on the ftp sight is german rom or am i looking in the wrong place.ok tried the ameo at me cousins and it works fine his hermes wont work at mine my unieversal does so does my psp so its goto to be a isue with my belkin n1 router.he has a belkin pre n g + and all our phones are working fine on it. what do you guys sugest
Click to expand...
Click to collapse
Hi
I use Belkin and and PK3.0 wm6 with WPA-TSK security enabled Wi-Fi connection to my athena no problem. You may have set up 54g connection only enabled in the router settings.
on the device start>> settings>> connections>>Wi-FI>>network Adapters then select IEEE 802........ and Select "The internet". Then press ok and reset the device
Belkin routers sometimes don't connect to the devices if you select higher security in wireless settings in the router. Therefore check the router's wireless settings.
set the device settings as above then Try modify settings in the router's wireless security settings. then save and restart the router and try connecting to the device.
I hope this will help you to connect to the Wi-fi internet. good luck
I dont know if this will help, but I have trouble connecting to my netgear router at home. It connects, but then shortly after, although still connected, loses its connectivity to the internet. To fix it, I have to turn off the power save mode to the wifi card and have the slidy bar to maximum performance to keep a connection
My preferred setup for WIFI
First and foremost, do a hard reset on the router by holding in the reset hole at the back for a few seconds until the lights blink.
Make sure security is OFF on the router and try to connect to it with your Ameo. If it works then yeehaa.....
The best setup I have at the moment with my router is with security DISABLED (believe it or not).
I then log into the router on my main pc and add a MAC FILTER list (i.e. the MAC addresses of the devices I wish to be allowed to connect to my router)
People may see a security-free router but they will NOT be able to connect unless their MAC address is on my router's list.
leoni1980 said:
First and foremost, do a hard reset on the router by holding in the reset hole at the back for a few seconds until the lights blink.
Make sure security is OFF on the router and try to connect to it with your Ameo. If it works then yeehaa.....
The best setup I have at the moment with my router is with security DISABLED (believe it or not).
I then log into the router on my main pc and add a MAC FILTER list (i.e. the MAC addresses of the devices I wish to be allowed to connect to my router)
People may see a security-free router but they will NOT be able to connect unless their MAC address is on my router's list.
Click to expand...
Click to collapse
Errr - if they want to, yes they will. All they need do is scan the network for an active MAC address and then spoof their own MAC address to one already active on the network. OK, it's unlikely anyone would go that far but I would much rather simply use the security!
On my TC500 (HTC Prophet G4) the Wlan doesnt work anymore.
I tried several roms, but always the same, the small symbol in the taskbar doesnt blink and doesnt show any wlans. are there any ideas to solve this?
Please help.
mc_chick
Hi, I have the same problem... but I discovered if you turn off you Prophet for a long while, and after ,restart again and you need to enable flight mode, and disable BT ( if it is enabled) the Wifi work. But after connecting to a network and try to saw samo internet pages... the Prophet freezes...
It is an hardware problem? or a soft problem??
i also have a similar problem... i can enable mi wifi , the light is blinking...but cannot find any networks even not searches..and when i my manually create the network and i'm step away from the acces point it sas unavailable... it started when i was using the latest i-mate rom...then upgraded the touch VII and touch VIII for now and no change...i gave up on the wifi and just surfing with the gprs ... i'm thinking of an hardware problem...cause i cant see the wifi adapter in the device manager which comes with touch VIII but can see other network cards...waiting for a solution for 4 months by now...=( thanx in advance...
Hello,
I got problems with my 3G connectivity. I've read this topic also:
http://forum.xda-developers.com/showthread.php?t=1239777
And manually selected my provider (Telfort).
But, my WiFi connection is also bad too. Sometimes it stops giving internet too. So I have to reconnect to the WiFi access point.
Beside that, When is coming 2.3.4 update to The Netherlands ?
Thanks.
when i finished flashing cm7 beta version on my att atrix and flashed the bell radio.
i found some issues with the network.when i connected to a wifi network,phone stuck with Obtaining IP address.... and need me to disconnect and reconnect again. and it occurs the same problem with the cellular network..i also need to disconnect and reconnect the network ,so that i can finally use 3g connection.
i wonder is it because i flashed the bell radio did not fit my att atrix??
kidqian said:
when i finished flashing cm7 beta version on my att atrix and flashed the bell radio.
i found some issues with the network.when i connected to a wifi network,phone stuck with Obtaining IP address.... and need me to disconnect and reconnect again. and it occurs the same problem with the cellular network..i also need to disconnect and reconnect the network ,so that i can finally use 3g connection.
i wonder is it because i flashed the bell radio did not fit my att atrix??
Click to expand...
Click to collapse
Your question answers itself
kidqian said:
when i finished flashing cm7 beta version on my att atrix and flashed the bell radio.
i found some issues with the network.when i connected to a wifi network,phone stuck with Obtaining IP address.... and need me to disconnect and reconnect again. and it occurs the same problem with the cellular network..i also need to disconnect and reconnect the network ,so that i can finally use 3g connection.
i wonder is it because i flashed the bell radio did not fit my att atrix??
Click to expand...
Click to collapse
I have a similar issue. Wi-Fi doesn't even attempt to connect to the network even when it's within range. It just says disconnected. Doesn't even let me manually reconnect it. So I have to turn the Wi-Fi off and turn it back on to have it reconnect it.
And no, I did not flash radio in long time. I have .30 Att radio.
Sent from my Atrix (CM7 beta on Crystal Theme)!
I also have the same problem, I'm using the correct radio but it just gets stuck on obtaining ip address when i turn wifi on.
I bypass this issue by using wifi manager as it forces the wifi to scan when you open it.
I have the widget on my home screen too for convenience.
I am having a similar connection problem with my wifi, when going from home to office and back my CM7 Atrix cannot connect to wifi because it says it is out of range. Each day I have to forget the wifi network and then rescan and then I can reconnect.
Anyone have any idea why this is happening?
Same problem here. Any resolutions yet?
DrNugu said:
Same problem here. Any resolutions yet?
Click to expand...
Click to collapse
flash radio supplied for your device, if yours is att, find att firmware and flash the radio present in it
i am running homebase 4.1. but internet radio and podcasts would not work when I click on them,saying that data connection not available(both 3G and WIFI are on). Does anyone know the solution?