hi
i have an atom with corrupted ext rom (based on the other threads i read). my screen is always stuck at the o2 screen.
so decided to download the official rom from o2 website and flash it. but when it reaches stage 3: update extended rom it is always stuck at 6%..
how can i solve this? is memory card a must to flash the rom?
and cos i cannot reach the today screen and therefore cannot sync. so i did this through bootloader..
Try Aku 3.3.3 released by jiggs
i am not able to download the rom.. having some issues with rapidshare..
Try below..
http://www.mediafire.com/?7txgxjlkwxt
thank you for uploading it.. but still have the same problem.. stuck at 6%.. waited for 5min already.. still waiting.. will post again..
remove the battery and leave it for a while.. then try flashing in bootloader mode..
According to previous posts, when the DSUU failed to format the Extended ROM, it stuck at 6%. The only thing you can do is to try to flash again and again...
You have to flash for two time using the rom version 20060721WWE, all-older roms cannot solve the problem. This error caused by the bootloader.
The first time you flash with the rom 20060721WWE, it uses the old bootloader already in your phone. So it stop at 6% Extended rom but succeeded to write its new bootloader to your phone.
Then the 2nd time you flash, DSUU will use the 20060721WWE rom's bootloader and will have no error.
Good luck!
check out below thread .. It may help..
http://forum.xda-developers.com/show...314613&page=76
http://forum.xda-developers.com/show...314613&page=77
http://forum.xda-developers.com/show...314613&page=78
Related
Any idea? I have to QTEK 8500. One upgraded nicely to 6.1 - the other gives me Error 270 after 5% flashing.
How can I bypass this?
The wiki seems not to exist at least at the moment (timeouts on requests), so I am lost here to know what to do.
Please advice
270 during flashing
First of all - as in instructions to flashing - make sure the phone is unlocked, both aplication and the other unlock.
If it still happens then I had the same thing. I used the clean "boring" ROM. After I changed the bootloader to a newer version, I was ok. So first flash the bootloader - it must be given on the same page as the rom file, and keep your fingers crossed - 'couse if it doesn't work you are in for a problem with a brick.
It should actually take a few seconds only.
After that, flash the new rom, should be ok.
No bootloader update - where is it?
The rom is from the article at http://forum.xda-developers.com/showthread.php?t=374397
(6.1 standard).
So, tell me - Where can I Find the instructions on how to update the boot loader?
Thona said:
the other gives me Error 270 after 5% flashing.
Click to expand...
Click to collapse
is it "corrupted image" error? if yes - READ THE ****ING MANUAL carefully and make sure you have done all the steps in it
Hi,
I had the same problem as you....
My phone was correctly unlocked, but it won't pass the 5% after a first try when i went to 97% (communication error). I was stuck on the nice Erofish sun starting pictures.
I tries many times to flash with the 6.1 standard, but it won't go through the 5% limit (the phone turns off at 5% but it was fully loaded). So I downloaded all the wm6 roms available in this great forum, try to flash them but it was not working (still stick at 5%).
So I doanload a 5.0 rom (Expansys forum : http://www.expansys-usa.com/ft.aspx?k=73618) and was able to flash my phone....
Then after I tried again to reflash with the Erofich rom, and was able to do it. So now, I can use my phone again with the great rom.
Regards,
F.
is it "corrupted image" error? if yes - READ THE ****ING MANUAL carefully and make sure you have done all the steps in it
Click to expand...
Click to collapse
I did - I can redo them, but this is the second phone I try to flash What step do you think I am missing? And it IS the corrupted image error. Is the application unlock wrong?
fdecourt said:
Hi,
I had the same problem as you....
My phone was correctly unlocked, but it won't pass the 5% after a first try when i went to 97% (communication error). I was stuck on the nice Erofish sun starting pictures.
I tries many times to flash with the 6.1 standard, but it won't go through the 5% limit (the phone turns off at 5% but it was fully loaded). So I downloaded all the wm6 roms available in this great forum, try to flash them but it was not working (still stick at 5%).
So I doanload a 5.0 rom (Expansys forum : http://www.expansys-usa.com/ft.aspx?k=73618) and was able to flash my phone....
Then after I tried again to reflash with the Erofich rom, and was able to do it. So now, I can use my phone again with the great rom.
Regards,
F.
Click to expand...
Click to collapse
Thanx! it worked!!!!
Thona said:
What step do you think I am missing?
Click to expand...
Click to collapse
Soft SPL aka SSPL aka USPL
Häh? Sorry, but where is that in the original documentation? I must totally miss it. I follow the instructions in the post verbatim.
It's included in the directions. Problem is, your phone is probably Application Locked. Try running the Application Unlock, then run the SSPL.lnk. When you run SSPL, it should put the phone into a virtual "bootloader" screen. This is where the RUU will run the upgrade process. This should get you taken care of. If not, let me know, we'll see what we can get going for you.
Hello
I have the same problem but when I flash with this original rom after 5% telephon turns off and it shows error 294 invalid vender ID
Anyone helps
Somehow i made hard reset and it works now
Hey guys...Heres a quick run down of whats happened:
Was upgrading to a new version of a custom ROM using SD method like i normally do. Process stuck at the very end forever (hours), so i soft reset. Now phone won't boot past the splash screen, just hangs there.
I have attempted the method "Phone bricked when writing to the Extended ROM" here: http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#error
But my problem is I cant use mtty because i have SPL 2.03.
How am I able to downgrade my SPL to 1.04 if I can't boot?
Or any ideas as to how i can get passed this an start clean altogether?
(I have already tried hard reset, no go)
Re-install the ROM using sd card method. If you think it could be a corrupt ROM image file, use a different ROM.
Might Work for you.
I had almost the same thing happen to my phone not but two days ago.
The problem I experience with SPL 2.03 after it bricked was that any new or custom Roms i tried flashing to my phone would error out before even starting the process.
What I did, and it worked for me, was to flash over the oldest original shipped Rom for my carrier. You can find it here.
http://wiki.xda-developers.com/index.php?pagename=Hermes_Upgrades
Load the Rom to your SD card and enter the bootloader. If your lucky it will start the process and finish.
Then as soon as its done, before putting a different Rom on there, use Hard-SPL. Here's the link and walk through for it.
http://forum.xda-developers.com/showthread.php?t=296722&highlight=bootloader
Let me know if it works out for ya.
Hello all!
I am in desperate need of some help from you all, and the great rom chefs here.
What exactly happened:
From past 2-3 roms (pandora 1.0, 1.1, PDAVIET-v6,v7) i have been having regular MANILA freezes. it would freeze within 12 hours of flashing, and in the last 2 flashes, it froze within 1 hour, without me installing anything.
Titanium worked fine. untill that started hanging too.
So i tried reflashing the 1.6 official rom, thinking that might clear up some bugs as its the official rom.
while trying to flash it (from my sd card directly) it gave up an error - Invalid DEVICE.
I restarted and went into bootloader again, and then i started getting this error :
UPGRADE ROM CODE ERROR
PLEASE TRY AGAIN
Now i have tried reflashing from the computer, and also from the sd card directly, 1.6 official , pandora 1.1, pdaviet v7, but to no success.
All the time it still gets stuck on that screen.
I have tried hspl'ing it again, it was successful - the hspl procedure, but then still no rom loads onto it.
Even tried using the sspl, but still nothing happens. With SSPL, it shows flashing as 0%, and stays there forever!
PLEASE HELP guys!
in a real bad situation!
Thanks!
so what is the device status currently?
can u boot into a main manilla or titanium screen?
Can you get to bootloader? Were you flahsing ROMs using SSPL or HSPL?
hi..
i dont know if this might work, try to get stock rom, xxx.exe, rename xxx.exe to xxx.rar and unpack it. you should see RUU_signed.nbh and rename to leoimg.nbh. put leoimg.nbh in the root of your sd card. and flash use vol down+power button.
oh, there was a mistake!
When you firstly flashed your device with 1.6 official from sd card, this removed hspl and the device checked your rom's region id. I guess you have used offical roms from other areas. So the process stopped when the device checked the cid.
At this stage, you should find out the offical rom from your area, and re-flash it from sd card, then everything will be fine.
But you didn't, you tried re-hspl and sspl...and i don't know what the consequence will be.
So? Did you get it fixed mate?
Any update? if you haven't fixed it yet PM me.
If it is de wrong region rom you tried to flash do you might need to flash it with a goldcard?
hope you got it sorted
Just flash your original rom using htc ruu will do. been there, done that
yeah flash the 142 or 148 rom that is appropriate for your device.. and use teh exe/ruu that came with it rather than sdcard.
what's the betting you needed the goldcard to flash 161? which is why you're having issues trying to reflash it ?
HSPL
Hi,
You could try this,
1) flash HSPL first.
2) flash the stockrom one more time from storage card.
This will erase hardspl so if you want to flash custom roms again you need to flash HSPL one more time after you flashed the stockrom.
Succes,
Leo
I have the same problem and I need the official 1.42 rom... do u know where I can find it?
_JuSteR_ said:
I have the same problem and I need the official 1.42 rom... do u know where I can find it?
Click to expand...
Click to collapse
Link from Dutty:
http://rapidshare.com/users/258XUJ
Your Leo was probably locked on your operator
at this point You've got to flash HTC official ROM with a Golcard.
Or your operator's rom directly from bootloader.
yep. I'm actually trying to get a gold card...
I've tried to create a gold card and hard reset but the setup fail
00018003
LEOIMG.nbh - FAIL
RADIO_V2 - RSA FAIL
rcust -
bootloader -
splash1 -
os -
configdata -
Update terminate
Update FAIL
Click to expand...
Click to collapse
maybe is the gold card wrong?
_JuSteR_ said:
I've tried to create a gold card and hard reset but the setup fail
maybe is the gold card wrong?
Click to expand...
Click to collapse
Did you try flashing thru boatloader official Rom (from your region) ?
I tried to install the latest HTC official rom but the setup stops at 9%
"Error [290]: invalid command"
It seems a problem of Radio... not rom...
_JuSteR_ said:
I tried to install the latest HTC official rom but the setup stops at 9%
"Error [290]: invalid command"
It seems a problem of Radio... not rom...
Click to expand...
Click to collapse
You have to flash 1.43 of your Region thru boatloader. If boatloader does not work thru goldcard.
I tried with italian 1.43 official rom also but the setup keeps stopping... Tried also using a goldcard, created using qmat
My HTC HD2 hang on HTC...
HARD SPL 2.08 HSPL
RADIO 2.15.5 (not show in boot loader mode)
i try many time for rom upgrade...(user latest energy roms also)
but not success...
i do hard SPL ok
flash radio ok
but
problem in rom upgrading....
1.Some time rom upgrade stop in 0%
2.Some time stop in 16%
3.Some time stop in 62%
4.Some time stop in 100% but NOT..show rom upgrade complet..(with SD)
what is problem here..
plz help me ....
Try this HSPL4 ................................
.................................................
kalros said:
.................................................
Click to expand...
Click to collapse
br i allready use this...
its ok my phone hardspl installed.
but ..
after this my problem start...
Have you also tried doing a Task29 first?
Which software have you tried to flash ROMs? Also LeoAdvancedRUU.exe or do you use SD card method only?
Have you tried another USB cable?
Have you tried another SD card (<=2GB)?
Have you tried to download the ROM file again?
Many questions, I know, but maybe also a solution.
chill it in teh fridge for half an hour then try flash your stock rom from sd card, if that works, you may have overheating problems.
if nothing works, remove HSPL and flash a stock ROM via USB or SD card, whichever suitable.
hi,
i have brand new hd2 tmobile. the phone stuck on the tmobile logo and didn't start-up.. i tried to flash the original tmobile stock ROM ** i got it from tmobile website** but it stuck in the flashing and refused to finish flashing.
i tried to install the ROM from the sd card but it always freezes in the radio flashing process.
i installed hspl3. now i have 2.8.hspl and tried to install the original stock ROM again and cocked roms through RRU.exe flashing and the SD card but no luck.
Also i did task29. it wiped out every thing yet no luck .
btw i try to flash radio 2.10.50.x
all the radios i did were 50
i use the reset button every time coz the phone wont respond unless i use it.
Bricked HD2
Make sure it's in bootloader and flash 2.08 HSPL to it via HD Tool Kit...Let it reboot,and pull the battery..Let it sit for 30 seconds..But the battery back in,and flash radio for Leo 2.15.50.14.It should flash the radio with no problems then.Best of luck with it.
Surgeman said:
Make sure it's in bootloader and flash 2.08 HSPL to it via HD Tool Kit...Let it reboot,and pull the battery..Let it sit for 30 seconds..But the battery back in,and flash radio for Leo 2.15.50.14.It should flash the radio with no problems then.Best of luck with it.
Click to expand...
Click to collapse
:good:
gdjy said:
hi,
i have brand new hd2 tmobile. the phone stuck on the tmobile logo and didn't start-up.. i tried to flash the original tmobile stock ROM ** i got it from tmobile website** but it stuck in the flashing and refused to finish flashing.
i tried to install the ROM from the sd card but it always freezes in the radio flashing process.
i installed hspl3. now i have 2.8.hspl and tried to install the original stock ROM again and cocked roms through RRU.exe flashing and the SD card but no luck.
Also i did task29. it wiped out every thing yet no luck .
btw i try to flash radio 2.10.50.x
all the radios i did were 50
i use the reset button every time coz the phone wont respond unless i use it.
Click to expand...
Click to collapse
I had that problem before. take the image and name it LEOIMG.nbh
put it on the root of the sd card than go into bootlaoder and follow direction to get it to work than pull battery.