Huge problem...no boot...need help please! - 8525, TyTN, MDA Vario II, JasJam Software Upgradin

Hey guys...Heres a quick run down of whats happened:
Was upgrading to a new version of a custom ROM using SD method like i normally do. Process stuck at the very end forever (hours), so i soft reset. Now phone won't boot past the splash screen, just hangs there.
I have attempted the method "Phone bricked when writing to the Extended ROM" here: http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#error
But my problem is I cant use mtty because i have SPL 2.03.
How am I able to downgrade my SPL to 1.04 if I can't boot?
Or any ideas as to how i can get passed this an start clean altogether?
(I have already tried hard reset, no go)

Re-install the ROM using sd card method. If you think it could be a corrupt ROM image file, use a different ROM.

Might Work for you.
I had almost the same thing happen to my phone not but two days ago.
The problem I experience with SPL 2.03 after it bricked was that any new or custom Roms i tried flashing to my phone would error out before even starting the process.
What I did, and it worked for me, was to flash over the oldest original shipped Rom for my carrier. You can find it here.
http://wiki.xda-developers.com/index.php?pagename=Hermes_Upgrades
Load the Rom to your SD card and enter the bootloader. If your lucky it will start the process and finish.
Then as soon as its done, before putting a different Rom on there, use Hard-SPL. Here's the link and walk through for it.
http://forum.xda-developers.com/showthread.php?t=296722&highlight=bootloader
Let me know if it works out for ya.

Related

Updating/Upgrading a HTC Cingular 8525?

Hi there everyone.
I have just bought a new HTC Cingular 8525 but it is running windows mobile 5. I would like to upgrade but I cannot find any downloads or instructions on how to do so. I do not want to brick up my new phone. Does anybody know a download link to upgrade to the latest windows mobile version that will work on my phone. Its an american bought phone which is unlocked and I am using it in the UK on Three. It used to be locked to at&t and I am pretty sure much of the at&t rubbish is slowing my memory and speed of the unit. If I were to upgrade will the phone still be unlocked?
Rom version is 2.15.502.3
Rom date is 04/09/07
Radio version is 1.40.30.00
Protocol version is 32.73.7020.16H
Operating system is (build 15706.3.5.2)
I am all new to this and would appreciate any advice idiot proof I have flashed many PSPs and other things but nothing like this.
As I have just got the phone I am still trying to work out how to use it so I have no idea how to do a Hard or Soft reset and have no idea about the roms
Sorry to waste your time
Please help
Rob
You should read through the Hermes wiki: http://wiki.xda-developers.com/index.php?pagename=HTC_Hermes
Make sure you install hardspl! If you install the "official" AT&T WM6 install hardspl again, your phone will stay unlocked, even with custom roms. If you flash one of the big storage roms, then go to try another, flash the "official" rom before flashing another custom rom.
Read the wiki: http://wiki.xda-developers.com/index.php?pagename=HTC_Hermes
I would also suggest making sure your phone is "super cid" before flashing custom roms, you'll also be able to flash from an sd card if you are super cid.
Read a bunch before flashing any radio roms!!!
Read, read, and re-read before you flash, and you should be fine. They have made the process fairly straight forward, but you can never be too sure. I have never "bricked" my phone, and I jumped in with both feet!
Mustn't flash a lot then because if you did you will end up with a brick sometime... I've always been able to recover my Hermes but there is STILL the possibility it won't.... one day...
ultramag69 said:
Mustn't flash a lot then because if you did you will end up with a brick sometime... I've always been able to recover my Hermes but there is STILL the possibility it won't.... one day...
Click to expand...
Click to collapse
I guess I have been lucky, but I'm sure I haven't flashed as much as others on here. But, I tried to follow the wiki, and tried to learn from others mistakes before I made some of my own. So, I figure if I can flash my Hermes, others should be able to do the same. And I have read up on the issues for when you "brick it", just in case.
I flashed several roms from the beginning (when I got my hermes), and learned a bunch. Then found what I needed/wanted in a rom, and spent days and days and days reading through many threads to find ones that fit me. I actually tried not to flash too much, but that can be a hard temptation to overcome.
So, just trying to pass on what has worked for me, to avoid the hard resets and such.
I would like to attempt cooking my own rom, and have read through tons of info on it, and played with some kitchens. Still working on learning that stuff, it'll give you a good appreciation of what the chefs around here do.
Whenever i get to the update part of the software my htc turns itself off and disconnects?
I then get the error 260?
robiscool said:
Whenever i get to the update part of the software my htc turns itself off and disconnects?
I then get the error 260?
Click to expand...
Click to collapse
I haven't ran into that one, but I went to the top of the page, clicked search, and typed in "error 260" (without the quotes). And got this http://www.google.com/cse?cx=000825...r+260&sa=Search&cof=FORID:0&ie=utf-8&oe=utf-8
hopefully one of those will help you....google is your friend
I found out that its because I'm running vista. I tried to view Mr. Vanx's guide but its no longer there at this link..
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=23&Itemid=27
So I am a bit stuck as I tried to do the following on here..
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeForBeginners
With no avail. It wont even let me install the HARD-SPL as it just gets stuck in bootloader mode with the error 260.
I have no idea what to do now. This process needs to be simplified more
http://www.mrvanx.org/thg/index.php?option=com_content&task=view&id=16&Itemid=26
Now make sure your device is on and activesync (or for vista users the WMDC) is running on your PC
Click to expand...
Click to collapse
I don't have anything running vista.
I still got the same error
thanks for your help though!
Go to post 1160 on page 116 of this thread - http://forum.xda-developers.com/showthread.php?t=296722
It tells you how to Hard SPL your Hermes with the sd card method. It also gives you ALL the apps needed.
After you Hard SPL your phone you can use the sd card method to flash a new OS. Flashing a new OS though requires you to drop steps 5 & 6 (you don't need sspl.exe once you have Hard SPL). Just remember though that the bootloader won't recognize any sd card bigger than 2gb...
Cheers...
Thanks for that. Its just now I have a problem where my phone is stuck on the Tri-Colour screen
Did you format the sd card fat32 (they are default format FAT) and rename the .nbh file to "hermimg.nbh"?
Is the sd card 2Gb or less?
You're on bootloader, is your SPL 1.09 des? If yes then insert the sd card and reset.
Cheers...
it might be an issue with activesync
i read somewhere before that activesync 6.1 won't sync with WM6 on vista machines.
I had to downgrade mine to ActiveSync 6.0 to get mine working again.
just an idea that might work

Did I brick my phone?

Hey All,
I just started working on my phone last night. I installed some 3.xxx radio, and a new ROM that I cooked up. The problem is I did not unlock the phone before I did it, so now I start the phone and it is stuck in a pre-splash screen. Does anyone know where I can get the stock Windows Mobile 6 ROM for it so I can re flash it and then re-cook it? Cause it has OBVIOUS signs that I tweaked it, so it would be hard to explain that it was something "A guy at circuit city" told me to do to get WM6.1. Please help!
Okay I need more specifics. What carrier are you working from?
Stuff
Verizion X6800 went from 2.04 radio to a 3.xxx and wm6 to wm6.1
Just flash your phone with Olipro from microSD card, then u can flash any ROM (exp DCD 3.2.6) also from SD card.
shag1233 said:
Hey All,
I just started working on my phone last night. I installed some 3.xxx radio, and a new ROM that I cooked up. The problem is I did not unlock the phone before I did it, so now I start the phone and it is stuck in a pre-splash screen. Does anyone know where I can get the stock Windows Mobile 6 ROM for it so I can re flash it and then re-cook it? Cause it has OBVIOUS signs that I tweaked it, so it would be hard to explain that it was something "A guy at circuit city" told me to do to get WM6.1. Please help!
Click to expand...
Click to collapse
Make it easy on yourself. Flash a Telus or Sprint ROM over to your phone. THis will fix any booboo's. YOU MUST STOP CARRIER CUSTOMIZATIONS from runing. After this is done, reflash with nueSPL 2.47 like you did and then put on a custom ROM.
This is your easiest option.
If you want the hard route put your phone in bootloader mode and tell me line by line what you see. That will tell us at what state you are in if you really want to try to figure out what you did wrong.
Either way, let us know how it turns out.
Read here for steps:
More info
TITA100 MFG
SPL-2.40.Olipro
CPLD-9
Its still messed up trying the other suggestions. Does anyone know where I can get the original. WM6 rom so I can try again. Or can I unlock it without it so I can load a ROM....also I don't have an SD card.
Thanks for all the help so far

C550 Refusing to Flash any ROM via MTTY

I've been having a few odd problems trying to get my C550 to flash a ROM of any kind using MTTY or Tera Term. I had been planning to reflash an old QTek ROM that I had on there, with one of the newer WM6.x ROMs that you guys have managed to put together. To recap, my C550 already has SuperCID, the SPL has been reflashed using Patched RUU and now reports 1.0.77 rather than the 1.0.16 or my other stock C550.
I can enter the bootloader fine and can connect to it using Mtty, making it respond to successfully to info and format commands, but when I try writing a new ROM, it just sits there doing nothing. I know it takes a while to reflash, but on my device it doesn't actually do anything even if you leave it for a couple of hours. The log looks as follows:
Cmd>l c:\rom.bin
clean up the image temp buffer at 0x8C080000 Length 0x01C40000
MTTYDownloadImage "c:\rom.bin"
:F=c:\rom.bin
start download​
The phone itself can be successfully reflashed using a ROM install package such as that of the old QTek ROM, or another T-Mobile ROM I have. The device can also be made to dump the current ROM to the miniSD card, so the bootloader seems to be functional. Which makes me wonder why this isn't working? I've tried flashing with and without the sim card, and also with and without an sd card in the handset, but it doesn't seem to make any difference.
If anybody has any suggestions of something else I could try, I'd greatly appreciate it! I had been thinking of trying to find an image dump of a WM6 ROM that I could then restore from miniSD, so if anybody would be able to that, it would also be appreciated.
Thanks for your help!
chilano
Please ignore the post above, I realised the SPL upgrade didn't seem to take until I used a different download of spl566wm6_spfans2006.nbf. Everything works fine now anyway.
Cheers for the wonderful work guys

HD2 Bricked!-Upgrade Rom Code Error - not able to get out. PLEASE HELP!

Hello all!
I am in desperate need of some help from you all, and the great rom chefs here.
What exactly happened:
From past 2-3 roms (pandora 1.0, 1.1, PDAVIET-v6,v7) i have been having regular MANILA freezes. it would freeze within 12 hours of flashing, and in the last 2 flashes, it froze within 1 hour, without me installing anything.
Titanium worked fine. untill that started hanging too.
So i tried reflashing the 1.6 official rom, thinking that might clear up some bugs as its the official rom.
while trying to flash it (from my sd card directly) it gave up an error - Invalid DEVICE.
I restarted and went into bootloader again, and then i started getting this error :
UPGRADE ROM CODE ERROR
PLEASE TRY AGAIN
Now i have tried reflashing from the computer, and also from the sd card directly, 1.6 official , pandora 1.1, pdaviet v7, but to no success.
All the time it still gets stuck on that screen.
I have tried hspl'ing it again, it was successful - the hspl procedure, but then still no rom loads onto it.
Even tried using the sspl, but still nothing happens. With SSPL, it shows flashing as 0%, and stays there forever!
PLEASE HELP guys!
in a real bad situation!
Thanks!
so what is the device status currently?
can u boot into a main manilla or titanium screen?
Can you get to bootloader? Were you flahsing ROMs using SSPL or HSPL?
hi..
i dont know if this might work, try to get stock rom, xxx.exe, rename xxx.exe to xxx.rar and unpack it. you should see RUU_signed.nbh and rename to leoimg.nbh. put leoimg.nbh in the root of your sd card. and flash use vol down+power button.
oh, there was a mistake!
When you firstly flashed your device with 1.6 official from sd card, this removed hspl and the device checked your rom's region id. I guess you have used offical roms from other areas. So the process stopped when the device checked the cid.
At this stage, you should find out the offical rom from your area, and re-flash it from sd card, then everything will be fine.
But you didn't, you tried re-hspl and sspl...and i don't know what the consequence will be.
So? Did you get it fixed mate?
Any update? if you haven't fixed it yet PM me.
If it is de wrong region rom you tried to flash do you might need to flash it with a goldcard?
hope you got it sorted
Just flash your original rom using htc ruu will do. been there, done that
yeah flash the 142 or 148 rom that is appropriate for your device.. and use teh exe/ruu that came with it rather than sdcard.
what's the betting you needed the goldcard to flash 161? which is why you're having issues trying to reflash it ?
HSPL
Hi,
You could try this,
1) flash HSPL first.
2) flash the stockrom one more time from storage card.
This will erase hardspl so if you want to flash custom roms again you need to flash HSPL one more time after you flashed the stockrom.
Succes,
Leo
I have the same problem and I need the official 1.42 rom... do u know where I can find it?
_JuSteR_ said:
I have the same problem and I need the official 1.42 rom... do u know where I can find it?
Click to expand...
Click to collapse
Link from Dutty:
http://rapidshare.com/users/258XUJ
Your Leo was probably locked on your operator
at this point You've got to flash HTC official ROM with a Golcard.
Or your operator's rom directly from bootloader.
yep. I'm actually trying to get a gold card...
I've tried to create a gold card and hard reset but the setup fail
00018003
LEOIMG.nbh - FAIL
RADIO_V2 - RSA FAIL
rcust -
bootloader -
splash1 -
os -
configdata -
Update terminate
Update FAIL
Click to expand...
Click to collapse
maybe is the gold card wrong?
_JuSteR_ said:
I've tried to create a gold card and hard reset but the setup fail
maybe is the gold card wrong?
Click to expand...
Click to collapse
Did you try flashing thru boatloader official Rom (from your region) ?
I tried to install the latest HTC official rom but the setup stops at 9%
"Error [290]: invalid command"
It seems a problem of Radio... not rom...
_JuSteR_ said:
I tried to install the latest HTC official rom but the setup stops at 9%
"Error [290]: invalid command"
It seems a problem of Radio... not rom...
Click to expand...
Click to collapse
You have to flash 1.43 of your Region thru boatloader. If boatloader does not work thru goldcard.
I tried with italian 1.43 official rom also but the setup keeps stopping... Tried also using a goldcard, created using qmat

Changing Everything to Default

Hi Xda Members,
I'm using HTC HD2 for 6 months.
I've installed Hard SPL first. Then i've upgraded my Radio Rom from 2.07 to 2.12. Then I've installed ChuckyRom and later I changed my rom to EnergyRom.
Now, I'm going to send my HTC HD2 to service and I want to send it with factory settings because of warranty issues.
I need to know;
1. How can I change the boot screen to original one? (The first one which seems when I turn on the phone; it shows ChuckyRom's boot screen now.)
2. How can I erase every clue about custom roms after flashing the shipped rom? Is it possible for them to understand that I had flashed a custom rom before?
3. When I press Volume Down + Start Button i see LEOIMG.nbh and other stuff. Is it possible to erase them? (I've removed the LEOIMG.nbh from SD Card already.)
If you help me I'll be grateful.
Tatenen said:
Hi Xda Members,
I'm using HTC HD2 for 6 months.
I've installed Hard SPL first. Then i've upgraded my Radio Rom from 2.07 to 2.12. Then I've installed ChuckyRom and later I changed my rom to EnergyRom.
Now, I'm going to send my HTC HD2 to service and I want to send it with factory settings because of warranty issues.
I need to know;
1. How can I change the boot screen to original one? (The first one which seems when I turn on the phone; it shows ChuckyRom's boot screen now.)
2. How can I erase every clue about custom roms after flashing the shipped rom? Is it possible for them to understand that I had flashed a custom rom before?
3. When I press Volume Down + Start Button i see LEOIMG.nbh and other stuff. Is it possible to erase them? (I've removed the LEOIMG.nbh from SD Card already.)
If you help me I'll be grateful.
Click to expand...
Click to collapse
I am using Energy rom, couple of months ago I sent my phone back for warranty. I just downloaded the latest rom from HTC site. If I remember correctly it changes hard spl and radio, but i'm not sure of that. Perhaps you need to install normal spl with the spl tool.
I know for sure that it also changed my boot screen to stock(with the red Vodafone boot screen for NL).
Hope this'll help you out a bit! Maybe this'll help too: http://forum.xda-developers.com/showthread.php?t=713977
Just flash a stock ROM from SD card. See forum.xda-developers.com/showthread.php?t=609477

Categories

Resources