I have upgraded and downgraded many times, never with a failure. I just upgraded to PDAVIET 4.0003. Went without a hitch but now my phone will not stay on the network, also it will every few minutes complain that there is no sim card. Card is fine as tested in my other phones. The interesting part is it functions fine on any 2.2 ROM.
Tried Smart1's True's and all PDAVIET, no WM6 allows the phone to work.
Cold resets don't resolve the issue. Is there something that could have gotten corrupted that is part of the phone OS and not in the ROM's?
I am at a loss to troubleshoot this issue.
Thanks for reading, any advice/suggestions is appreciated.
ron1n, what is the network protocol for your provider?
Do you use pap or chap, the setting choice in CommManager?
Is network set for auto in phone dialog?
In your connection settings, do you use Server assigned ip address or auto?
Since i have upgraded to PDAviet i have almost the same problem.
After soft-resetting my device no gsm connection is found.
The only solution is to go into phone option and start the manual search.
If it's connected it works without any problems.
Strange thing....I also tested a few gsm roms but always the same experience.
R0N1N said:
I have upgraded and downgraded many times, never with a failure. I just upgraded to PDAVIET 4.0003. Went without a hitch but now my phone will not stay on the network, also it will every few minutes complain that there is no sim card. Card is fine as tested in my other phones. The interesting part is it functions fine on any 2.2 ROM.
Tried Smart1's True's and all PDAVIET, no WM6 allows the phone to work.
Cold resets don't resolve the issue. Is there something that could have gotten corrupted that is part of the phone OS and not in the ROM's?
I am at a loss to troubleshoot this issue.
Thanks for reading, any advice/suggestions is appreciated.
Click to expand...
Click to collapse
Reflash Radio ROM (2.47.21 or 2.69.21 will work)
To reply to all of your suggestions. I have tried 5 different radio roms, none will see the phone network (GSM not GPRS) for more than a few seconds with a weak signal, then they fail and either go to flight mode or say that the SIM is missing. To reiterate, this was working fine up until yesterday with a few different WM6 ROM's. Coincidentally, the rear speaker failed at the same time. I resolved that issue, but the lack of phone service persists, although all AKU 2.2 ROM's work fine. Very curious....
DeviLduck said:
ron1n, what is the network protocol for your provider?
Do you use pap or chap, the setting choice in CommManager?
Is network set for auto in phone dialog?
In your connection settings, do you use Server assigned ip address or auto?
Click to expand...
Click to collapse
It is CHAP, although I am referring to the phone service not wireless GPRS. My network is configured for auto, although if I switch to manual (due to the lack of consistent conntection), it will not be able to see any networks, except briefly and intermittently.
Cheers
WM6 Sim Card issues [solution, use radio rom 2.19.21]
I've been using WM6 for awhile now, I've tried SMART1.3, PDAVIET 4.0.0.01, 4.0.0.0.3,4.0.0.0.3a and finally 4.0.0.0.4 .. but yesterday i tried to flash back to SMART1.3. After downgrading and upgrading, i got unknown sim status ! since yesterday , I've change my Radio Rom and OS ( I've tried almost everything ) but i can't get my phone to work in WM6 !! when i flash back to wm5 ( any AKU 2.2 version ) i have no problem with phone or GSM but as soon as I upgrade to WM6, I got unkown Sim status ... anybody , have any Ideas ?!!
Same Problem !
I have exactly the same problem !! it's not from radio ROM or OS !! I've tried 3 different version of radio ROM, and almost every single WM6 OS that is out there ! my phone stop responding yesterday after i changed my OS from PDAVIET 4.0.0.0.4 to SMART1.3 ! since then I've tried everything, but I can't get the phone to work in any WM6 OS! although WM5 (any version of it) is okay !
hma4 said:
I've been using WM6 for awhile now, I've tried SMART1.3, PDAVIET 4.0.0.01, 4.0.0.0.3,4.0.0.0.3a and finally 4.0.0.0.4 .. but yesterday i tried to flash back to SMART1.3. After downgrading and upgrading, i got unknown sim status ! since yesterday , I've change my Radio Rom and OS ( I've tried almost everything ) but i can't get my phone to work in WM6 !! when i flash back to wm5 ( any version) i have no problem with phone or GSM but as soon as I upgrade to WM6, I got unkown Sim status ... anybody , have any Ideas ?!!
Click to expand...
Click to collapse
Did it used to work?
Yes , it used to work ! I've been using WM6 for more than 2 weeks with no problem! recently I upgrade my os to PDAVIET 4.0.0.0.4, but I decide to change the OS back to SMART 1.3, after I changed it back, i got the error "Unknown SIM card , without the pin you can call emergency calls only" I tried my pin and PUK , but none works ! So i changed the OS to WM5 again. I've tried couple of different version of WM5 (JESTER, NVID) and I've found the phone works perfectly in wm5 !! as I said before I tried re-flashing my Radio ROM, but it didn't help !! i still can't get my phone to work in WM6 ! any of Pocket PC gurus, have any suggestion ?
S200 Gone Wacko with WM6 and I don't know why
Hello people
Okay so here is the situation, since about last week I have been using PDAViet 4.0.0.3 on my Qtek S200
Now I love this ROM..so much so that I spoon with it at night...um...crap lol Its fast and lite...but something went terribly terribly wrong yesterday
So around 1pm I disconnect my phone from my computer, and notice a "X" in the data connection arrows...okay I thought nothing of it. I go to a restaurant, get a phone call from my brother, and talk, and everything is fine. From there it went bonkers...it kept on trying to connect a GSM signal, and then would go out to no service...it would keep on trying and trying, and bogging down my phone....
So finally i got it stablize (with an EDGE data signal i thought) and of course a voice signal and went on my merry 2 hour drive back home to Montreal.
When I got to Montreal and was waiting in the dead moving traffic jam, I wanted to check the Windies cricket score on BBC, so I take out my phone and try to make a data connection. But again the X showed...i rebooted my phone and signal about 10 or 20 times, and finally got something...however by the time that happend I had arrived at home so i went and used my computer.
The GSM signal stayed, but I dont know if I had a data connection. I then went to a funeral, turned off my radio entirely, and then when I turn it back on...ooooooooo no signal...it would get 2 bars, and then drop, and then 2 bars "E" symbol, and then drop.
So from then on, i went nuts, opened up the back, took out the battery, checked the sim, installed another sim to make sure..and by now it went even worse..first INVALID SIM...then it went to MISSING SIM...urge to kill rising!
I finally said F it, and hard resetted my phone...but i noticed something upon the screen calibration..."NOTIFICATION ERROR...cannot find calnot.exe". After hard resetting and such, the problem still showed...
This morning, after leaving it overnight, it was still misbehaving...so I went to took it back down to the floating NVID file found here on XDA developers...and oddly enough...no more calnot.exe error...the radio signal is strong, and i get a data connection...So i tried to then upgrade to the new PDAViet 4.0.0.4s ROM, but again...calnot.exe error...so finally i am stuck at the NVID ROM...oy!
So I searched here on XDA Developers and on google...now while people have said they get the calnot.exe error, they also get this reglog.dll (or something to that effect) error as well...me on the other hand am only getting that calnot.exe error, which would seem to be the root of my problem.
What can I do fix this, and get back to the speedy 4.0.0.3 ROM (man I love that ROM)
Phone info:
ipl: 2.09
spl: 2.20.0000 (so I guess that my Qtek S200 is a G3 model)
radio: 02.47.21 (i even moved up to 02.69.21)
os: 2.20.7.34
so i really appreciate the help guys...take care...
*howls like a wolf*....nothing?
hofo_mofo said:
*howls like a wolf*....nothing?
Click to expand...
Click to collapse
Flash again the WM5 NoVid Rom,hard reset and if you come up with the same error,hard reset again... Tell me what happens... If it works flash PDAViet 4.0.0.0.3a...
Holy S*** I have the same Problem for like two weeks!!
Man , I have exactly the same problem !!! exactly !! i had PDaviet 4.0.0.0.4 and one day I got the same thing, No signal , then after i hard reset, the Calnot error ! then Hard reset again, and this time I got the replog error !
I get "Unknown Sim Card!" or "Unknow Sim Card status enter your pin" whenever I install WM6! My phone works perfectly in Wm5 though !!
I flashed radio rom in WM6, I also tried different sim Cards , but none works !I can not get the phone to work in wm6!
By the way, NVID is not a good rom to stay with.
tonydeli7 said:
Flash again the WM5 NoVid Rom,hard reset and if you come up with the same error,hard reset again... Tell me what happens... If it works flash PDAViet 4.0.0.0.3a...
Click to expand...
Click to collapse
Still the same thing...i have treid 4.0.0.0.3a, 4.0.0.0.3, 4.0.0.0.4, 4.0.0.0.4s, 4.0.0.0.4sse, and Mobiz 2.0b3.....all nothing...
Sometimes it would be calnot.exe notification error, or replog.dll, or now clocknot.exe error...so far only NVID works
hma4 said:
Man , I have exactly the same problem !!! exactly !! i had PDaviet 4.0.0.0.4 and one day I got the same thing, No signal , then after i hard reset, the Calnot error ! then Hard reset again, and this time I got the replog error !
I get "Unknown Sim Card!" or "Unknow Sim Card status enter your pin" whenever I install WM6! My phone works perfectly in Wm5 though !!
I flashed radio rom in WM6, I also tried different sim Cards , but none works !I can not get the phone to work in wm6!
By the way, NVID is not a good rom to stay with.
Click to expand...
Click to collapse
In a way I am glad you are having the same problem...so I know I am not a nut lol (and nor am I alone)...but of course its not good to relish in someones downfall, so of course it is also a bad thing eh..
What ROM would you suggest then? NVID seems alright, but I don't know of any others out there (well somewhat)...thanks!
I wish we knew why it happened at first place!
for wm5, if you want a clean, fast and reliable Rom, try Jesterz Rom
http://forum.xda-developers.com/showthread.php?t=284578
you might want to re flash the start-up image to HTC logo... you can find the .cap in the same thread.. I also updated the radio rom too, you can find it in prophet wiki.
Jesterz Rom is nice cause you don't have to uninstall anything, it's really clean and stable. it is by far better than NVID, but don't ask why cause i have to ramble a lot.
Oh by the way if you found out why this happened to us .. let me know
hofo_mofo said:
Still the same thing...i have treid 4.0.0.0.3a, 4.0.0.0.3, 4.0.0.0.4, 4.0.0.0.4s, 4.0.0.0.4sse, and Mobiz 2.0b3.....all nothing...
Sometimes it would be calnot.exe notification error, or replog.dll, or now clocknot.exe error...so far only NVID works
Click to expand...
Click to collapse
Try flashing PDAViet WM5 Temp
http://rapidshare.com/files/32728615/Prophet_PDAViet_Step1.zip PASSWORDDAVIET
or PDAMobiz WM5 Temp......
http://www.sharebigfile.com/file/178269/fantastic-b3-Step1-rar.html
and then try to flash truneytral's WM6 if you haven't already...
http://www.savefile.com/files/763142
If you don't want russian keyboard ,just follow DEVILDUCK's procedure here http://forum.xda-developers.com/showthread.php?t=302067&page=18
and follow the guide
http://forum.xda-developers.com/showthread.php?t=310452(just flash one of the above Wm5 temp roms,instead of NVid)
tonydeli7 said:
Try flashing PDAViet WM5 Temp
http://rapidshare.com/files/32728615/Prophet_PDAViet_Step1.zip PASSWORDDAVIET
or PDAMobiz WM5 Temp......
http://www.sharebigfile.com/file/178269/fantastic-b3-Step1-rar.html
and then try to flash truneytral's WM6 if you haven't already...
http://www.savefile.com/files/763142
If you don't want russian keyboard ,just follow DEVILDUCK's procedure here http://forum.xda-developers.com/showthread.php?t=302067&page=18
and follow the guide
http://forum.xda-developers.com/showthread.php?t=310452(just flash one of the above Wm5 temp roms,instead of NVid)
Click to expand...
Click to collapse
Okay, I spend another 2 hours to update the phone ! This time i didn't get the
Calnote.exe or replog error !! but my phone still doesn't work !
The phone connection is not stable ! it comes and goes ! and i get " Unknow SIM status. 3 attempts remaining. Only emergency calls can be made without a pin." well i tried different sim card , and i still get the same error !
HELPPPPPPPPP Pleaseeeeeee !
I just Upgraded my phone to ASreg3.3.12, and LvsW Aku2.3 and still doesn't work !!
I get the same error ! the Phone App doesn't function! I get Unknown Sim Status! I've tried NVID, and Jesterz Roms , both AKU 2 and both work fine !!
any suggestions ?
Strange, however, can you post which radio version you have when you switch roms ? it could a radio rom problem....
Hi,
I purchased the Softbank X01HT (post Dec) in Japan when i was working in Japan. I lived with the Japanese OS even though i don't understand Japanese because I didn't want to temper with it just incase something goes wrong and i can't use the phone. Well, now im back in Australia ... and i need to unlock it and flash a new ROM to it so that I can use it in Australia .. otherwise.. it is effectively a brick....
so.. i spent the past two days reading all the valuable information u guys provided... and in the end.. i decided to first unlock and superCID my phone using the AUTO_Unlock_v3a.bat provided by POF ... and then flash it with the Jasjam telstra ROM (RUU_Hermes_DL_UK_3[1].62.305.5_6275_1.54.30.10_108_Ship.exe) also found in this forum which received good feedbacks...
ok... after i executed the AUTO_Unlock_v3a.bat program .. everything went well... and at the end of it.. the screen even said.. successful in both unlock and superCID ... so.. i assumed that my phone is unlocked...
then... i went to flash my phone with the abovementioned jasjam ROM .. and this too.. everything went just fine ... and now.. my phone is working with this new ROM (cool! first time im able to read my x01ht coz its in English) ...
without a sim.. the OS works fine.. etc etc...
however, when i tried to put a telstra sim card in it ... its still simlocked ...
the SimLock screen comes up and requests me to input unlock code ...
so.. i did more reading and researched but can't find any solution to this ... i even tried that "unlock" code (22051978) but it doesnt work ...
Please.. can someone help me with this issue with my phone? now.. it seems that i just need to unlock my phone to use it as my jasjam ROM is working fine. Below are further details:
ROM version: 3.62.305.5
ROM date: 11/06/07
Radio version: 1.54.30.10
EtRom version: 3.62.305.116
any help/comments will be highly appreciated... thanks in advance...!
read somewhere that if you let the softbank go through the 1st boot and it installs all the extra stuff you wont EVER be able to unlock it again. some one else may need to clarify this but apparently you need to soft reset after you've reached the today screen but before the customisations start. if you didnt do this then you probably wont be able to unlock it. sorry if this is wrong/bad news.
Hope someone else can corroborate this.. cheers...
thanks for your reply ultramag69 although i hope that u r wrong.. hahaha
fingers crossed ... hopefully.. positive news from some experts ...
After re-reading the posts, i cannot find that I did anything wrong.
This link "http://forum.xda-developers.com/showthread.php?t=293665" states that the unlocker v3a "can be used in all HTC Hermes devices, no matter which bootloader version the device is running", with the exception of "x01ht post April devices" (i.e., white x01ht).
However, my x01ht is black and is a pre-April device.
So, I am still not sure what is wrong. Please help please help any experts out there ...
POF ... if you are there.. please help ... i need your expert advice thank you in advance.
ultramag69, i think that you are referring to this "http://forum.xda-developers.com/showthread.php?t=301952".
Quote:
"Here's how to unlock the new batch of SoftBank X01HT devices with radio 1.14.01.10.
This process is ONLY valid for new devices which have never turned on or let the SoftBank Extended ROM install.
If you have already let the ExtROM install you CAN'T sim-unlock it."
Fortunately, i find that this does not apply to me because my phone is not post april. Also, originally, my radio was never 1.14.01.10. It was 1.14.00.10.
help..........
snowboarder said:
Hi,
I purchased the Softbank X01HT (post Dec) in Japan when i was working in Japan. I lived with the Japanese OS even though i don't understand Japanese because I didn't want to temper with it just incase something goes wrong and i can't use the phone. Well, now im back in Australia ... and i need to unlock it and flash a new ROM to it so that I can use it in Australia .. otherwise.. it is effectively a brick....
so.. i spent the past two days reading all the valuable information u guys provided... and in the end.. i decided to first unlock and superCID my phone using the AUTO_Unlock_v3a.bat provided by POF ... and then flash it with the Jasjam telstra ROM (RUU_Hermes_DL_UK_3[1].62.305.5_6275_1.54.30.10_108_Ship.exe) also found in this forum which received good feedbacks...
ok... after i executed the AUTO_Unlock_v3a.bat program .. everything went well... and at the end of it.. the screen even said.. successful in both unlock and superCID ... so.. i assumed that my phone is unlocked...
then... i went to flash my phone with the abovementioned jasjam ROM .. and this too.. everything went just fine ... and now.. my phone is working with this new ROM (cool! first time im able to read my x01ht coz its in English) ...
without a sim.. the OS works fine.. etc etc...
however, when i tried to put a telstra sim card in it ... its still simlocked ...
the SimLock screen comes up and requests me to input unlock code ...
so.. i did more reading and researched but can't find any solution to this ... i even tried that "unlock" code (22051978) but it doesnt work ...
Please.. can someone help me with this issue with my phone? now.. it seems that i just need to unlock my phone to use it as my jasjam ROM is working fine. Below are further details:
ROM version: 3.62.305.5
ROM date: 11/06/07
Radio version: 1.54.30.10
EtRom version: 3.62.305.116
any help/comments will be highly appreciated... thanks in advance...!
Click to expand...
Click to collapse
hey bro!when you r already flashed v3a unlock,than you should down a software name like "Hard-SPL-V7",it will help you to unlock the exrom,make you able to flash the new os\rom...
"HARD-SPL-V7" has 2 software,1st is "RUU_signed.nbh",2nd is "RUUWrapper.exe".
devileric, read post carefully. snowboarder has no problem with reflashing oses, its the sim that needs unlocking now and hard spl WONT do that...
Still reading and researching. I'd probably retry the unlock tool. it cant hurt but may work... cheers
devileric ... yes ... ultramag69 is correct ... my new English Telstra Jasjam OS works like a beauty when it operates WITHOUT a sim card. However, when i try to insert a telstra (or optus) sim card in there, there is a prompt that requires me to enter a unlock code. Please note that the unlock code 22051978 does NOT work in this case (also doesnt work in alot of other cases that i read in this forum).
Ultramag69, thank you for your help and replies, much appreciated. I actually did try the unlocking program again (three times ) . However, when i execute the AUTO_Unlock_v3a.bat when my OS is the new telstra jasjam OS, my phone will freeze on the telstra startup screen after the radio update step of the unlocking program when it automatically resets. Thereafter, even when i perform soft reset again and again, it will just freeze there. When that happened the first time, I thought that I bricked my phone .. ahhaha.. but fortunately, I was able to simply go to the tri-color boot screen and then simply flash the above said telstra Jasjam ROM. This will get me back to square one, i.e., working Jasjam OS, but phone is still sim locked.
I spent another night last night reading the applicable threads. I find that quite afew other people had the same problem as me. And I also find that whenever such problem is posted, its either ignored or a moot reply is given.
So, for the experts out there, if there is a solution to this, please kindly let me know. I am sure it will others will find it helpful too. Thank you.
Sorry wrong post
Hi guys,
I've got a very big problem with my Jamin G4.
When I insert the SD Card (2G no HC), the phone shows me that something happened (the backlight turns on) but the pone doesn't show it in File Explorer and in Settings -> Memory -> Storage Card says: Not installed.
I read all forum about this problem and I didn't found anything to work. I formatted the card Fat, Fat32 and nothing. I have 2 friends with 2 same Jamins where i tested the card. It is installed ok, no problems. So the card it's ok, it's new
The problem is at my pda. When I got the pda, I did Hard SPL from Update_Package but I didn't know that first u have to run "HardSPL.bat" so , for real I didn't HardSPL but I didn't know that at that time, and I tried to install a WM6.1 Rom. Off course I get error and I recovered the phone with RUU-Prophet-G4-AKU2.2-2.20-2.47.21-Jester-r1.exe . I noticed that my IPl/SPL has changed when I installed the Jester's ROM. After that, I did a proper HardSPL and installed a WM6.1 rom.
After that, I bought this SD Card and noticed that doesn't work. I thought that the problem was with the changed IPL/SPL so I installed a WM5 rom from Imate.com to change them back but didn't worked.
I don't know what to do anymore. I still belive that the problem is software and not hardware but I don't manage to fix it.
Any suggestions please?
Thanks in advance,
Razvan
I forgot to tell you. My curent config is:
IPL: 2.20.0001
SPL: 2.G4.4PDA
GSM: 02.07.20
OS: 2.13.9.23
Please help me because without SD i can't do many with the PDA.
razvanct said:
I forgot to tell you. My curent config is:
IPL: 2.20.0001
SPL: 2.G4.4PDA
GSM: 02.07.20
OS: 2.13.9.23
Please help me because without SD i can't do many with the PDA.
Click to expand...
Click to collapse
Flash again or Flash other rom....
I flash it with original ROM from imate.com, I flash it with RUU_Prophet_220734_2207114_024721_NVID.exe , I flash it with your roms, Gullum, etc and nothing.
My IPL/SPL changed from 1.xx to 2.20.xx and nothing .. I don't know what to no more .. I have one question though:
Is the any posibility to be a hardware problem even if, when i insert/pull out the card, the light turn on?
If u have other sugestions, please tell me .. maybe others had the same problem .. thank you!
I always notify the guysabout this problem and no one solve it
try 1d it will work
I tried "1d-Storm-4" and same: not working ...
I think I found a problem, when the rom customize, it reset when installing SDcard.txt ..
razvanct said:
I tried "1d-Storm-4" and same: not working ...
I think I found a problem, when the rom customize, it reset when installing SDcard.txt ..
Click to expand...
Click to collapse
that is normal reset if you don't have the SD config. file made in the SD card,
did you ever try other SD card? if same, mostly will be hardware problem.....
Good Luck
razvanct said:
I tried "1d-Storm-4" and same: not working ...
I think I found a problem, when the rom customize, it reset when installing SDcard.txt ..
Click to expand...
Click to collapse
I told you "1d" not "1d storm"
I have thee same problem and I know the perfect roms for it
believe me dioxda2 the problem from roms
bcuz some roms work fine like ur "1d" -not "1d storm"
I can't find just "1d" .. can u give me a link please? Thank you, mostafa0007
i have a dopod 830 which has same SD card issue, my solution is to delete or rename wifiinit.lnk from \windows\startup folder and do a soft reset. this is becasue dopod 830 has no wifi modual, when it starts up, wifiinit may prevent SD card funtion normal.
not sure if this can fix your problem, but worth a try. wish you luck.
razvanct said:
I can't find just "1d" .. can u give me a link please? Thank you, mostafa0007
Click to expand...
Click to collapse
dioxda2 -the coocker- replace the link for 1d version from his topic and put 1d storm insted of 1d ... this is the problem
So strange .. I don't have anything in \windows\startup folder .. is this ok?
hi lol
errrrrrmm
i tried updating my htc athena/ameo but it got stuck in the boatloader screen n i tried hard resetting which didnt work n i sent it to the company to fix but they were charging £350 something n i aint ready to pay dat so can anyone please help me with how i can get my phone back to normal ??
this comes on when i switch it on
ATHE100
1PL-v2. 01
ATHE100
SPL-v1. 06. 0000
please help ?
thanks
if you are in bootloader, try to flash your device with a rom (spl1.2)
flash your athena with memmory card
about flashing
sorry but this is abit hard when i dont know much about the whole flashing thing , can u explain please
Here you have complete tutorial for flashing with SD card http://wiki.xda-developers.com/index.php?pagename=HTC_Athena. Basically you got to have slow SD card rename xxx.nbh file to ATHEIMG.nbh and copy the file on the card. Insert SD card in athena remove sim card and hard reset the athena (camera button and reset). Then you will see flashing gray screen. USE THE ROM YOU HAVE ON YOUR DEVICE. if you flash your device with rom for spl3.5 you will loose device ID and have a lot of problems (i had them )
lilp399 said:
sorry but this is abit hard when i dont know much about the whole flashing thing , can u explain please
Click to expand...
Click to collapse
Reading the wiki for Athena will help you better understand flashing. You can also contact OliPro or Cmonex as they are the most experienced former Athena team members. If you want to send me a pm, I may be alble to help you offline from the forum in an msn chat session or equivalent.