hi
I need your help to fix my O2 Atom Exec.
i wanted to upgrade my ROM in to the WM6, at the bigining i copied the "diskimage_Ver.nb0" & "EBOOT.nb0" on my memory card. and got my Atom Exec into the bootloader , after download complited the LCD got dark, i got it on bootloader and start the "Device Software Update Utility" and clicked on "Next" until "Upgrad" was shown.When I clicked on "upgrade" this error was shown:"CONNECTION ERROR" . What should i do to fix it?
Thanks.
I'm looking for your answer.
donot ever try thru SD card.. there is a chance that you may brick your device.
Goto bootloader mode first then u run DSUU.
Now after i did that, it dosent work with DSUU .it show "error connection".and my divice shows the upgrade fail
How many files you have in the upgrade directory? Normally it should contain 6 files:
- Device Software Update Utility.exe
- diskimage_Ver.nb0
- EBOOT.nb0
- ExtendedRom.img
- nova_pda_033105.mot
- vl1d_pda_Ver.mot
It will always shown connection error if one of these files is missing
I have all of them,
It seems feasiable to full downloadig the Rom from SD(memory card), but i need mor files:
"diskimg.nb0 , eboot.nb0 , dm.nbo , flash.img , agent.mot , mot.mot , CPLD.img , assetInf.img , extended.img , Mdoc.img"
If it's possible to upgrading with them how can i rech them ?
hello...!!!?
can enybody help me with this case? I need Your Help. Please. . . .
shaemna said:
hi
I need your help to fix my O2 Atom Exec.
i wanted to upgrade my ROM in to the WM6, at the bigining i copied the "diskimage_Ver.nb0" & "EBOOT.nb0" on my memory card. and got my Atom Exec into the bootloader , after download complited the LCD got dark, i got it on bootloader and start the "Device Software Update Utility" and clicked on "Next" until "Upgrad" was shown.When I clicked on "upgrade" this error was shown:"CONNECTION ERROR" . What should i do to fix it?
Thanks.
I'm looking for your answer.
Click to expand...
Click to collapse
Why did you do this?! No one gave out instructions to flash anything using SD CARD in the first place! Of course you will get connection error because bootloader is not functioning. Remove your SDCard, start bootloader mode, and flash the normal way.
I did that but it's not worked. and got me "error connection", i saw some where that if i do it in the that way (with sd) it's worke and beacuse of that i did it in that wey, now what should i do? how can upgrad my ROM or downgrad it, my divice is alredy ded, how can i get it alive? help me
shaemna said:
I did that but it's not worked. and got me "error connection", i saw some where that if i do it in the that way (with sd) it's worke and beacuse of that i did it in that wey, now what should i do? how can upgrad my ROM or downgrad it, my divice is alredy ded, how can i get it alive? help me
Click to expand...
Click to collapse
can you go into bootloader mode?
yes it's go to the bootloader but when run DSUU plase of the last version of the rom and radio is empty, when i click on UPGRAD it get me ERROR CONNECTION
shaemna said:
yes it's go to the bootloader but when run DSUU plase of the last version of the rom and radio is empty, when i click on UPGRAD it get me ERROR CONNECTION
Click to expand...
Click to collapse
I'm sorry. I don't get you. You can go to bootloader, but you get an error. Can you post a screen shot of the error? so, I will know what to do.
How can I uplod picturs?
server is busy it get me Network Error (tcp_error) and cant upload it
the doucument of it is:
(the upgrade page)
Your Divice software is about to be update from:
divice CE image version:0
divice Radio image version:
to:
CE image version: 7210621
Radio image version: R060711N-MN2ARC-RS00011
.......
PLEAS CLICK update to continue
when i click upgrade it show me the fowloeeng error
ERROR:CONNECTION ERROR
THE DIVICE SOFTWAR UPDATE IS HAVING TROUBLE CONECTING TO YOUR DIVICE
PLEAS CHEKE
1)YUOR DIVICE IS PROPLY CONNECTED TO THE USB CABLE OR ...
.
.
.
now what should i do?
do you have any other USB to mini-USB cable? try changing it... The ones used for SD Card readers or Digital Cameras are the same, and do it again.
i do that in all of my USB ports and they are same and get me error conection again
Is there any wey else to inistall a ROM on my divice?
1) Is windows recognizing your device?.. (Do you have activesync installed?)
2) Did u try using different USB cable ?
3) Are you logged on as administrator?
4) Did you remove SD card before going to bootloader mode
5) What is the screen content when you go to boot loader mode
6) Before connecting the device go to bootloader first, then connect the device and then run DSUU
7) Activesync may install device drivers for your device so try installing activesync?
Thanks
when i get my divice in to the bootloader it's display:
===========MN2 Bootloader=
Jun 13 2006 20:41:44
copyright (c) 2006 Quanta cor
poration
CPLD Ver: A0060109
***********************
*Using '<-','->', 'Enter' *
*to choose what you want *
***********************
(1)debug module through UART
(2)jump to DM
enter your selection:
when i conect it to pc( as administrator user) the fallowing line was shown:
USB connected , waiting for download command...
and my computer beeping and found new hardware but not connected to activesync(4.5) , then i start DSUU and when start to upgrade computer show me "ERROR CONECTION" and my divice show me this note:
! ! ! Please use DSUU in OS mode and sync with pc first ! ! !
Usb transfer Fail
please help me
1. We get the most first sewing of Xda-atomexec-eng-20060614_r060428n_ex0028.exe (only by this sewing restore was able)
2. We drag out the files of eboot.nb0
3. We copy on miniSD in a root directory.
4. We insert miniSD in Pocket, enter in bootloader (Camera+SR)
5. We wait inundated while.
6. We take out a miniSD, enter in bootloader, start sewing on PC, connect to USB (it is needed to put to death in the processes of AS)
We are sewn!!!
Related
XDA O2 on Wallaby BootLoader v5.15 I see the error : "GSM ERROR"
my pda don´t start good I only see the rom version (3.17.03) and a blue wallpaper of O2..
I already update my rom but it don´t work yet !
Where can I find a rGSM rom update?
What more can I do ?
Please, help me !
thanks
Joao Afonso, from Portugal
How to fix GSM Error Problem ....
Download the XDA-Developers ROM Version 1.1.
Install the ROM on your Device via SD-Card and bootloader.
The phone should start up and give you the screen allignment and the whole menu!
Download an Upgrade for your device. This depends ont the model you are using. Check the sticker at the back of your device.
If it is a PW10A-Model download RSU Version 4.16.
If it is a PW10B-Model download RSU Version 6.24.20.
Extract the downloaded ZIP-File and copy all files to the /Windows directory of your device.
Copy the RSUpgrade.exe additional to the /windows/startup directory.
Make an soft reset of your device.
Maybe the upgrade will stop again at 1%, this may occur when you have an empty battery.
Place your device in the cradle. Run Active Sync on your device.
The RSU Upgrade will run in the background.
Wait for about 10 Minutes. The upgrade should complete in the background....
Afterwards all should work again...
Good luck....
Click to expand...
Click to collapse
I did exactly what you said in your page !!!
I installed rom without problems, the problem is when I want to install program B, i copy files to sd card, and with the explorer in the rom i copy it to windows and .exe file to windows/startup
Next I restart XDA and setup begin, it stop with 1 % (you said in your page) that it is hapen because I have few batery power..., it´s true..
so I open active sync in PDA and in my PC, put the cable on in the two devices, but PC don´t connect ..
Can you repeat in other way, how to do ?
i have to turn on active sync in the pc and PDA ?or only in the pda ? I don´t have docking station to PDA, I only have the Sync cable, I charge my PDA over that, but now, I can´t charge it ? why ?
I have to restart PDA other time, (press ok to restart) or I only open active sync, and have to press in sync to run program B.
Thanks for your time and patient..
Joao Afonso (a beguinner in XDA..)
I'm new to the whole Hermes upgrading scene - but have read just about every forum thread and post on upgrading. I'm trying to follow this process:
http://forum.xda-developers.com/showthread.php?t=312943&highlight=vista
I chose to upgrade via SD card, since my windows box is a vista machine and I primarily use my mac day to day. Here's the problem I'm having - when I try to flash HardSPL V7 via the SD card (using the filename hermimg.nbh in the root of the SD card), it starts to say "loading" in bootloader mode, but then flashes up "00068002" in red at the top of the screen, and then continues into normal 3 color bootloader mode.
When I try to do the flash from vista with RUU (after following the guides showing how to downgrade to the XP drivers), I get a 262 error, and when I look in RUU.log, I see the following:
00:24:27:674 [msg] : Version : [5.10 - 20060412].
00:24:30:851 [msg] : Current Not in CE Mode or in CE Mode but ActiveSync Not Connected.
00:24:34:879 [msg] : Disconnect ActiveSync .... [0]
00:24:34:880 [msg] : Start Get Connect Port.
00:24:35:025 [msg] : Current in BL Mode. Open Port : [\\.\WCEUSBSH001] OK.
00:24:43:512 [msg] : Device BL VER : [1.04] [].
00:24:43:522 [msg] : =============================================
00:24:43:524 [msg] : START GetNBHInfo !
00:24:43:525 [msg] : END GetNBHInfo !
00:24:47:310 [msg] : Check Ac in BL mode. AC : [1]
00:24:47:314 [msg] : IsBL. BL : [1]
00:24:49:363 [msg] : =============================================
00:24:49:384 [msg] : START UpdateNBH !
00:24:50:577 [msg] : Upgrade 2 : 0 Start.
00:24:51:310 [err] : Receive Data Error : 0x713, 0x00068002.
00:24:52:040 [err] : Receive Data Error : 0x708, 0x00018002.
00:24:52:790 [err] : Receive Data Error : 0x708, 0x00018002.
00:24:52:791 [err] : Write NBH Data Error.
00:24:52:793 [err] : BL UpdateNBH Error.
00:24:52:821 [msg] : START UnInitialization !
00:24:52:843 [msg] : END UnInitialization !
Notice the line "00:24:51:310 [err] : Receive Data Error : 0x713, 0x00068002." - that 00068002 is the same number that pops up when trying to flash from the SD card.
Same exact thing happens when I try to flash anything else (like a radio rom, or an OS rom).
Any help would be greatly appreciated!
PS: my TyTN shows as a HERM200, IPL 1.00, SPL 1.04
Did you format your SD Card in Fat32?
The most common problem when flashing from card is a wrong formated card.
yes, i formatted it Fat32 and also did a chkdsk on it.
Did someone get the solution for this?
Why you people do not search before making posts?????!!!!!!
Here is what u asking for :
1. Format your SD card with FAT32.
2. Download Hermes SIM CID Unlock v3a.
3. Copy SSPL-HERM to your SD card.
4. Extract the RUU_HERM_Unlock_v3a.
5. copy HermesUnlocker_HardSPL.nbh to SD card.
6. Rename it to HERMIMG.nbh.
7. put the SD card into the device and run sspl.exe.
8. the device enters the bootloader and ...
I have problem flashing using Sandisk 1GB, formatted FAT32, .nbh in place, after tri color bootloader nothing happen, no 'Loading'. Anybody experience this problem?
When I use micro SD 256 MB (from Nokia), no problem at all, flashing process Completed.
Is SD capacity (too big) become an issue or is this bad SD card..?
some sd cards cant be used to flash roms, i dont know why, maybe someone else can explain why
argupas, did you rename the .nbh file to "hermimg.nbh? It MUST be renamed to this for sd method to work. cheers.....
ultramag69 said:
argupas, did you rename the .nbh file to "hermimg.nbh? It MUST be renamed to this for sd method to work. cheers.....
Click to expand...
Click to collapse
I already rename .nbh to HERMIMG.nbh.
I think it was SD card problem (1 GB Sandisk, I suspect a fake one), because I am now using 512 MB V-gen, no problem for flashing.
Thx.
koorosh_bsboys said:
Why you people do not search before making posts?????!!!!!!
Here is what u asking for :
1. Format your SD card with FAT32.
2. Download Hermes SIM CID Unlock v3a.
3. Copy SSPL-HERM to your SD card.
4. Extract the RUU_HERM_Unlock_v3a.
5. copy HermesUnlocker_HardSPL.nbh to SD card.
6. Rename it to HERMIMG.nbh.
7. put the SD card into the device and run sspl.exe.
8. the device enters the bootloader and ...
Click to expand...
Click to collapse
I dont understand 7th step. Now my device hang in "Windows Mobile" screen, so how can I run sspl.exe. And also if enter the bootloader, I can press Power+OK+soft reset. Is this right for enter bootloader or i must run sspl.exe?
you have to run SSPL.exe from the file explorer. It has to be run from the PHONE memory, NOT the sd card.
Try a hard reset, both soft keys and reset with stylus. Hold all buttons until it asks if you wish to reset to factory (or something like that, you get the idea). Push "r" on slideout keyboard then "space"key. you now have to go through the alignment and everything again.
Even if you use this method, make sure you install Hard SPL V7. It is safer than anything else. You should also have checked what radio rom you were using as it has now been downgraded to 1.116.x.x, this may cause you some trouble later too.
Use the sd card method to fix this as it appears safer than using the pc. Just make sure you have got Hard SPL installed and have a charged battery. DON'T just think you can put it on the charger while flashing AS IT DOESN'T CHARGE...
Cheers...
Sorry to replay this thread but i had a situation like that.
I have a Hermes, with the pin of the USB that makes connection to PC broken... So my only Shot to update the ppc is from SD. The rom i have is one of 1st realeses of hermes wm6.5, so that stucks all the time, even i hard reset it...
When i try to update something from SD i cant because gives me that error 000602... Any idea? So i have to unlock the cid, but if i cant access to the windows what i must do?
If i hard reset it, it enter in windows, but 2 ou 3 seconds that stuck :S
If you can't get into windows to run SSPL.exe to install Hard SPL & your USB is stuffed so you can't connect to PC then you have a brick... If you had Hard SPL installed 1st then you wouldn't be in this situation.
Sorry, you have a brick unless you fix the USB connector.
ultramag69 said:
If you can't get into windows to run SSPL.exe to install Hard SPL & your USB is stuffed so you can't connect to PC then you have a brick... If you had Hard SPL installed 1st then you wouldn't be in this situation.
Sorry, you have a brick unless you fix the USB connector.
Click to expand...
Click to collapse
Ok, but if i fix the usb... updating by bootloader mode and usb, i will not get the error 00068002?
Not if you install Hard SPL 1st...
I dont understand 7th step. Now my device hang in "Windows Mobile" screen, so how can I run sspl.exe
Click to expand...
Click to collapse
same me too,
My device Stuck on bootloader, Why can I run sspl.exe?
Need Help
SOLVED:::::: sorry
aladin said:
same me too,
My device Stuck on bootloader, Why can I run sspl.exe?
Need Help
SOLVED:::::: sorry
Click to expand...
Click to collapse
First off, reflash your device with your phones original carriers ROM. Your phone will accept it. It sounds like you didn't SUPERCID your phone first, and didn't HARDSPL your phone.
Make sure you HARDSPL then SUPERCID your phone FIRST!
Download your phone's original carriers ROM and flash that via SD card to your device. That should return it back to "factory" state, and get it so that you can once again try to HARDSPL and SUPERCID your phone.
Hope this helps,
Cheers
Supercid then Hard SPL... If you run the V3a unlocker it flashes your SPL to 1.40... Hard SPl V7 is the latest and greatest. Technically you shouldn't need to supercid your Hermes after Hard SPLing it.
Hi
your instruction are really complete and clear but . . .
but my TyTn to day has a problem (better I have a problem!!)
After breaking the flash of a new ROM (it was corrupted) it either stays in bootloader mode (IPL 1.01 SPL 2.03) or,after few seconds from booting and displaying all data like
M 05 R 1.56.70.11
S 04 G 32.89.7020.20H
B 06 D 3.57
turns the display full white, make a "ding" and never enter into W.M. 6.5. Hence, how can I launch HERMES-SPL.exe ???
Other attempts to flash from PC through:
- RUUWrapper provide up-date error for missed USB connection
- <ROM>. exe the flash starts but stops after few second when the status bar, on the PDA reach 1%.
So, it became a brick?? There is any chance to retrive it?
3351405372 said:
Hi
your instruction are really complete and clear but . . .
but my TyTn to day has a problem (better I have a problem!!)
After breaking the flash of a new ROM (it was corrupted) it either stays in bootloader mode (IPL 1.01 SPL 2.03) or,after few seconds from booting and displaying all data like
M 05 R 1.56.70.11
S 04 G 32.89.7020.20H
B 06 D 3.57
turns the display full white, make a "ding" and never enter into W.M. 6.5. Hence, how can I launch HERMES-SPL.exe ???
Other attempts to flash from PC through:
- RUUWrapper provide up-date error for missed USB connection
- <ROM>. exe the flash starts but stops after few second when the status bar, on the PDA reach 1%.
So, it became a brick?? There is any chance to retrive it?
Click to expand...
Click to collapse
Hey bud, if you hold the POWER BUTTON and the CAMERA button down and hit the RESET button, do you get a tricolour screen?
If so, then your phone is not bricked, just has a failed ROM on it.
You can flash via SD card onto your phone, and to do so, download the rom for your network, the one that originally came with your phone, onto your phone. when you put it on the SD card, make sure you name it HERMIMG.nbh. This'll allow you to flash via SD. put the card in, reset to the tricolour screen, and then follow the instructions for flashing.
Once this is done, you can then attempt again to SuperCID your phone.
Cheers!
Everybody plz help me!
I haven't bricked my Atom Exec, but I can flash it no more!
I was trying to cook my own ROM, but after I successfully flashed it, I found it very buggy. I wanted to flash it back, but the device cannot establish a standard patnership with ActiveSync 4.5, only guest mode can be used. When I tried to used DSUU, it stuck. When I entered bootloader (060613 MN2), it refused to DSUU, saying that it must run under Sync (but I can't! ), and when I inserted the SD card with diskimg.nb0, it showed "SD download complete" immidiately after beginning, and nothing flashed.
How can I recover my system? Please help me! Thank you very much!
BoomerCE said:
Everybody plz help me!
I haven't bricked my Atom Exec, but I can flash it no more!
I was trying to cook my own ROM, but after I successfully flashed it, I found it very buggy. I wanted to flash it back, but the device cannot establish a standard patnership with ActiveSync 4.5, only guest mode can be used. When I tried to used DSUU, it stuck. When I entered bootloader (060613 MN2), it refused to DSUU, saying that it must run under Sync (but I can't! ), and when I inserted the SD card with diskimg.nb0, it showed "SD download complete" immidiately after beginning, and nothing flashed.
How can I recover my system? Please help me! Thank you very much!
Click to expand...
Click to collapse
have a try, remove your SD card, and go into bootloader mode, then run DSUU, good luck.
raftcham said:
have a try, remove your SD card, and go into bootloader mode, then run DSUU, good luck.
Click to expand...
Click to collapse
Yeah, but the bootloader told me that it can only flash under Sync mode
You have to flash with another Atom Exec ROM. No choice. And being in guest mode doesn't disable flashing last I checked.
Don't worry!
You have to flash your bootloader with an older version, and then flash new rom in bootloader mode.
First: You need extract file eboot.nb0 from the rom “Xda-Atom-ENG-20060614” and copy this file to the root directory of your Mini SD card. Insert this card into your Atom and press Reset + Camera to go into bootloader mode. Your atom will download this new bootloader and then reboot.
Becareful!Be sure that the file is copy 100% correctly to your card and plug your Atom to a charger before upgrading. Remember that uprom from SDcard is dangerous.
Second: remove your sdcard, go into bootloader mode again, connect your Atom to PC and run DSUU to flash rom (DSUU might stuck at 6% while flashing the extended rom). But at this time, you can press reset and it will start the OS.
If your Atom boot normally and you can run camera apps, your phone is OK. If it not, you have to connect it to PC and run DSSU one more time.
Good luck! Sorry for my bad English!
Problem solved and thanks to everyone
Hi, i have the problem with the threadstarter. Wanted to change my Atom Exec cht rom back to wwe version. But i keep encountering bootloader telling me that it can only flash under Sync mode.
Anyone could help?
Thanks
wonder12 said:
Hi, i have the problem with the threadstarter. Wanted to change my Atom Exec cht rom back to wwe version. But i keep encountering bootloader telling me that it can only flash under Sync mode.
Anyone could help?
Thanks
Click to expand...
Click to collapse
Run CHT DSUU as normal; then before the final confirmation, copy WWE ROM files and overwrite all CHT files, then confirm flashing. That may help. There was a thread about downgrading Atom Exec ROM to Atom ROM that can also help you.
Hello
I have a problem with my Prophet and he needs to go to the factory..i need to install wm5 ,i have a wm6 rom and when i downgrade to wm5, the pda goes to bootloader and appears the following window:
ERROR 302 UPDATE ERROR
The Rom Update Utility has encountered communications errors during the update process. The Program will guide you step-by-step to recover from the errors so you can continue with the update!
I have the following advice but it stop´s on bootloader..
Need urgency help! Tks
tiagofa said:
Hello
I have a problem with my Prophet and he needs to go to the factory..i need to install wm5 ,i have a wm6 rom and when i downgrade to wm5, the pda goes to bootloader and appears the following window:
ERROR 302 UPDATE ERROR
The Rom Update Utility has encountered communications errors during the update process. The Program will guide you step-by-step to recover from the errors so you can continue with the update!
I have the following advice but it stop´s on bootloader..
Need urgency help! Tks
Click to expand...
Click to collapse
if u are in Bootloader mode the one in three color mode.. U can downgrade surely with PDA viet temp.
In Boot loader mode just reconnect your device to pc through USB . and launch the PDA VIET program..
It should be work.
doesn´t work..
is there any connection with SD slot card doesn´t work ?.. ?? :S
help.. :S
u r using vista right?
u should do that with xp
be sure that with xp u can fix it 100%
no, i+m using xp.. still doens´t work..
i think my prophet dies :S
try flashing NVID wm5 when in bootloader. if you were successfull flash HardSPL and after that you original ROM!
First, disable any firewall
Put the prophet in bootloader (3-clored screen) by pushing CAM button and punching the reset hole at the bottom. When you realease the stylus, the colors should appear.
Then, before connecting your prophet to the PC, first DISable the "Allow USB connection" option in the connectionsettings box of ActiveSync.
After that connect the bootloadermoded Prophet to your PC, it conects as an ordinairy USB device. Then run the RUU of your choice.
probably the better idea is to send a snapshot of your display in fault mode.
do that with a camera. it could be useful to identify the state of your error.
i'm not skilled but here you can find a pool of powerfull developers.
jork
problem solve
problem.. usb port lol :S
i buy atom pure from my friend,i have problem to revert back.this atom pure already upgrade to atom exec window mobile 6 profesional 5.2.1413 (18508.0.7.0).but have problem with phone,cant make a call os sms.now im planning to revert back to wm5 original. i already try download original rom Xda-Atom-ENG-20060426-MOT0822.exe but still cant flashing.and show "eror:connection eror"
do i need flash my bootloader 1st?then running then run Xda-Atom-ENG-20060426-MOT0822.exe ?
what file need to copy in the sd card?
nitrospeed said:
i buy atom pure from my friend,i have problem to revert back.this atom pure already upgrade to atom exec window mobile 6 profesional 5.2.1413 (18508.0.7.0).but have problem with phone,cant make a call os sms.now im planning to revert back to wm5 original. i already try download original rom Xda-Atom-ENG-20060426-MOT0822.exe but still cant flashing.and show "eror:connection eror"
do i need flash my bootloader 1st?then running then run Xda-Atom-ENG-20060426-MOT0822.exe ?
what file need to copy in the sd card?
Click to expand...
Click to collapse
Try press "camera button" + "reset button" then plug your usb cable and
run your original rom.
Cheers,
Benz
still cant flashing."error : connection error"
nitrospeed said:
still cant flashing."error : connection error"
Click to expand...
Click to collapse
Have you installed activesync 4.5 btw??? If yes continue to read below, if not get activesync first.
change USB cable, it may be deffective. any cable will do, motorola, canon digicam et al. then try steps below
put device in bootloader mode: camera button + reset hole
plug usb device then run original ROM.
read the wiki thats why it's there!!!!
maybe help
try flashing it while its still connected via active sync and not in the bootloader mode if its still show error connection mode then it must be the rom is not compatible for ur device or there is really a problem with the connection
ok i found the solutions.i try search for 2 days.then i found this.
http://www7.discuss.com.hk/archiver/?tid-5578529.html
now im working on it.i hope it successfull