Ahh help! Cannot unlock AT&T 8525 - 8525, TyTN, MDA Vario II, JasJam Software Upgradin

Im pretty new to this whole process, and i went over the unlocking thread with the v.3a. I tried and tested this method, but EVERY time, it goes to the simLock screen and tells me i've entered the code x times, and to wait for timeout. The buttons are greyed out so i cannot enter my own code!
This is a new phone and I havent put my own sim card in it yet (Don't know if i HAVE to do that), I tested with a T-mobile sim card.
Rom Version: 2.15.502.3
Rom date: 4/9/07
Radio version 1.40.30.00
Protocol version: 32.73.7020.16H
IPL - 1.03
SPL - 1.11
Any help would be GREATLY appreciated! Im such a newb at this!!! Thanks!

Noone has any answers? =*(

You need a Cingular / AT&T SIM to be able to do this. I'm stuck in your same situation right now.
Hope that helps.

8525
i just unlocked my AT&T 8525 pretty easy with pof's v.3, when i did it i had no sim chip in the phone. i dont think the sim chip matters much until the unlocking process is over.

with pof v3a
sixteenounces said:
i just unlocked my AT&T 8525 pretty easy with pof's v.3, when i did it i had no sim chip in the phone. i dont think the sim chip matters much until the unlocking process is over.
Click to expand...
Click to collapse
I did everything that i have been asked by it and at last it finished and when i put my simcard which is t-mobile in it, it says that "YOu have tried 6 times please wait until time out " and it is taking more than 12 hours now to time out what should i do is the phone unlocked?

maybe a hard reset will let you try again faster?

Related

M600 SPV Unlock Mess - Have I Killed It!?

Hi
I was given an Orange SPV M600 running WM5.0 I foolishly thought I would be able to unlock it to work with my T-Mobile sim (the only network I can get coverage at home) I ran an unlock tool from en.pdamobiz.com
http://files.pdamobiz.com/c/PDAMobiz.com_ProphetAKU2_unlockCID.rar
I managed to get to through to the completion of the Downgrade.bat process. I was then asked to sofdt boot the M600 but it now cannot be found by Activesync. I was unable to successfully run Unlockcid.bat and now it just boots to either the 'Orange' screen (displaying IPL 2.10.0001, SPL 2.10.0001, GSM 02.07.20 & OS 1.0.13.21 - the new OS I believe) or the 3 colour screen (displaying IPL 2.10.0001, SPL 2.10.0001) if I hold down the camera button.
Windows 5.0 has gone or is unreachable but I am assuming it can't be completely dead as I get a noise when connecting/disconnecting the USB lead....
Is this false hope? Have i killed it after 2 days of ownership??? Should I have attempted this process with very little tech knowledge - me thinks YES!
I would be eternally greatful to anyone who can help me out of this black hole..... I just need pointing in the direection of what stage the M600 is at and how to get it running on my T-Mobile sim.....
Thanks in advance
hi there, try going into the bootloader screen, when you connect the usb cable it should show on the bottom off your screen. then try uploading the orange rom you can find on the wiki page. if this works then try using the loki unlocker which you should also be able to find on the wiki page. i used the loki tool and it unlocked first time. hope this helps. let me know how you go.
The GOOD news is No you haven't killed it. It seems you have wiped the operating system from it. I would sugest searching for RUU-Prophet-G4-AKU2.2-2.20-2.47.21-Jester-r1.exe down load it and then get your phone to the multi colour screen before running the download. This should then update your phone
when I tried to unlock my phone, I couldn't get it to unloack at all till I put a orange pay as you go sim in the phone and registered the sim with orange then it unlocked first time.
Killed prophet reborn!!
Fingers666 said:
hi there, try going into the bootloader screen, when you connect the usb cable it should show on the bottom off your screen. then try uploading the orange rom you can find on the wiki page. if this works then try using the loki unlocker which you should also be able to find on the wiki page. i used the loki tool and it unlocked first time. hope this helps. let me know how you go.
Click to expand...
Click to collapse
Spot on. Thanks so much for the advice. Fingers666 & jazpa !! I'm back on track. M6000 is now communicating again. WM5 is resident. Just need to unlock the sim and I'm away. [email protected] tried loki 3.0 amd 3.0a with both Activesync 4.2 and 4.5 respectively without any luck so I've just spent £5 a http://www.unlocking.org.uk/ as they say they can unlock a G4 ver. We shall see!! Great help though and THANKS again to both of you
Please Help Meee!!
Hello i was wondering if anybody could help me.
I want to unlock my orange SPV M600 for free.
If there are any safe and free websites that anybody knows of could u please tell me.
Thank Youu!!
James Thomas
Download Lokiwz, it is quite easy to locate. Inside the folder you will find 1 or 2 cab files, copy these to your storage card and run them on your M600. Now run Lokiwiz from your PC, after around 12 minutes, it will display your sim unlock code. Switch off your M600 and insert the sim you want to use, at the prompt, enter your code lokiwiz generated. For around 2 minutes the phone will seem to have no signal, then it will connect.
Worked first time for me, my M600 was locked to Orange, now it works great with O2.
wonderful works great with G4
thanks
mike

Not sure which unlock will benefit me

Ok well I had a unlocked 8125 and I stumbled across a new 8525 for 150, so I picked that up... Now I should be getting it tomorrow and my question is this...
I'm assuming I fall under the post April category(being brand new) with the difficult SIM unlocking procedure... Now I'm not really in to switching around my carrier, I have AT&T its a AT&T branded phone and I'm fine with that... the only thing I really care about is being able to flash different OS roms and whatnot.
So do I just run the auto unlocker and only select CID unlock??
I've been trying to read and find out if the auto unlocker CID option will still work for post April units but I haven't been able to find the response yet.
Or am I totally in left field on this??? Do I need both CID and SIM unlocked to do OS rom flashes??
I acquired the 8125 already unlocked and those tend to be easier to do stuff to than these, or I'm just not reading the right thread.
Any info is appreciated.
I will not be turning the unit on till I hear a response from you guys. Worse case I just wont let the customization complete.
BerettaFreak said:
Ok well I had a unlocked 8125 and I stumbled across a new 8525 for 150, so I picked that up... Now I should be getting it tomorrow and my question is this...
I'm assuming I fall under the post April category(being brand new) with the difficult SIM unlocking procedure... Now I'm not really in to switching around my carrier, I have AT&T its a AT&T branded phone and I'm fine with that... the only thing I really care about is being able to flash different OS roms and whatnot.
So do I just run the auto unlocker and only select CID unlock??
I've been trying to read and find out if the auto unlocker CID option will still work for post April units but I haven't been able to find the response yet.
Or am I totally in left field on this??? Do I need both CID and SIM unlocked to do OS rom flashes??
I acquired the 8125 already unlocked and those tend to be easier to do stuff to than these, or I'm just not reading the right thread.
Any info is appreciated.
I will not be turning the unit on till I hear a response from you guys. Worse case I just wont let the customization complete.
Click to expand...
Click to collapse
You only need to do CID for that purpose. You are correct. Of course, doing SIM won't hurt you, but you only NEED CID.
Ok so when I get this phone... turn it on, do touch screen thing, do other crap, and CANCEL the customization with a soft reboot??? and then I can sim unlock it?
What sim unlocker do I use and whats the best radio for my location? Phone will actually be delivered today so this is why I'm asking.
Wait I think I got it... Turn on phone... Reboot before customization...
Run AUTO_Unlock_v3a once connected, after 1.16 radio installed then run Herm_Unlock_v3.exe to unlock it and once that is done run SoftBank_1.33.761.4_Extrom to remove the bootloader update.exe and then I can hard reboot without problems...
That sound right? This is following POF's thread on how to unlock these... http://forum.xda-developers.com/showthread.php?t=301952
I just run olipro 2.10 hardspl v7 and then I can flash any rom and radio I wish.
Yes but mine is a post April release phone which aparently has a radio bootloader update to 0182 which then makes the Radio rom un updatable, or impossible to unlock the sim.
Unless I dont need the Sim unlocked to do radio updates... but the more I read leads me to believe I wont be able to update the radio if I let the 0182 radio bootloader update run.
OR unless I'm completely retarded and this doesnt apply to the AT&T 8525.... I cant really find that on here.
Either way I'M LOST!
Yeah I think I'm retarded and read too far into this... I don't think the AT&T 8525's have this Radio Bootloader update thingy thats coming on the SoftBank phones...
Well all is good... fired the phone up, used it for all of 20 min before I used the auto unlocker on it unlocked CID and SIM, and then flashed it with VP3G WM6 rom, and the newest 1.54 radio... all is good so far.
Ok, I think I'm still at 1.04 IPL and 1.40 SPL, Olipro, is it worth it for me to install the Hard SPL v7 update??
IPL and SPL stuff on these phones are slightly more confusing than on the older 8125's
Also how do you get to the 3 color boot loader screen manually?
I did a HTC WM6 flash, wasnt very impressed and went back to the vp3G setup... Also is the 1.54.07 radio any good... the HTC rom put me down to 1.48 and since the 1.54 takes 20 min to upload I may leave it as is right now.
BerettaFreak said:
Ok, I think I'm still at 1.04 IPL and 1.40 SPL, Olipro, is it worth it for me to install the Hard SPL v7 update??
IPL and SPL stuff on these phones are slightly more confusing than on the older 8125's
Also how do you get to the 3 color boot loader screen manually?
I did a HTC WM6 flash, wasnt very impressed and went back to the vp3G setup... Also is the 1.54.07 radio any good... the HTC rom put me down to 1.48 and since the 1.54 takes 20 min to upload I may leave it as is right now.
Click to expand...
Click to collapse
I would update to the latest HardSPLv7. Oli makes it better every time - more protection.
1.54 is an AT&T release, so it is probably better than 1.48. I think 1.50 was also an AT&T release, but you can use it and see if it works. The biggest difference usually seems to be battery.
Regarding putting into bootloader screen, I don't have my phone on front of me, but I am sure it is in the wiki. It is a right side button, a left side button and the press the reset hole on the bottom. I think it is the bottom side buttons - OK, PTT and the reset hole. (I think)

unlock my x01ht unsuccessful... any ideas why?

Hi,
I purchased the Softbank X01HT (post Dec) in Japan when i was working in Japan. I lived with the Japanese OS even though i don't understand Japanese because I didn't want to temper with it just incase something goes wrong and i can't use the phone. Well, now im back in Australia ... and i need to unlock it and flash a new ROM to it so that I can use it in Australia .. otherwise.. it is effectively a brick....
so.. i spent the past two days reading all the valuable information u guys provided... and in the end.. i decided to first unlock and superCID my phone using the AUTO_Unlock_v3a.bat provided by POF ... and then flash it with the Jasjam telstra ROM (RUU_Hermes_DL_UK_3[1].62.305.5_6275_1.54.30.10_108_Ship.exe) also found in this forum which received good feedbacks...
ok... after i executed the AUTO_Unlock_v3a.bat program .. everything went well... and at the end of it.. the screen even said.. successful in both unlock and superCID ... so.. i assumed that my phone is unlocked...
then... i went to flash my phone with the abovementioned jasjam ROM .. and this too.. everything went just fine ... and now.. my phone is working with this new ROM (cool! first time im able to read my x01ht coz its in English) ...
without a sim.. the OS works fine.. etc etc...
however, when i tried to put a telstra sim card in it ... its still simlocked ...
the SimLock screen comes up and requests me to input unlock code ...
so.. i did more reading and researched but can't find any solution to this ... i even tried that "unlock" code (22051978) but it doesnt work ...
Please.. can someone help me with this issue with my phone? now.. it seems that i just need to unlock my phone to use it as my jasjam ROM is working fine. Below are further details:
ROM version: 3.62.305.5
ROM date: 11/06/07
Radio version: 1.54.30.10
EtRom version: 3.62.305.116
any help/comments will be highly appreciated... thanks in advance...!
read somewhere that if you let the softbank go through the 1st boot and it installs all the extra stuff you wont EVER be able to unlock it again. some one else may need to clarify this but apparently you need to soft reset after you've reached the today screen but before the customisations start. if you didnt do this then you probably wont be able to unlock it. sorry if this is wrong/bad news.
Hope someone else can corroborate this.. cheers...
thanks for your reply ultramag69 although i hope that u r wrong.. hahaha
fingers crossed ... hopefully.. positive news from some experts ...
After re-reading the posts, i cannot find that I did anything wrong.
This link "http://forum.xda-developers.com/showthread.php?t=293665" states that the unlocker v3a "can be used in all HTC Hermes devices, no matter which bootloader version the device is running", with the exception of "x01ht post April devices" (i.e., white x01ht).
However, my x01ht is black and is a pre-April device.
So, I am still not sure what is wrong. Please help please help any experts out there ...
POF ... if you are there.. please help ... i need your expert advice thank you in advance.
ultramag69, i think that you are referring to this "http://forum.xda-developers.com/showthread.php?t=301952".
Quote:
"Here's how to unlock the new batch of SoftBank X01HT devices with radio 1.14.01.10.
This process is ONLY valid for new devices which have never turned on or let the SoftBank Extended ROM install.
If you have already let the ExtROM install you CAN'T sim-unlock it."
Fortunately, i find that this does not apply to me because my phone is not post april. Also, originally, my radio was never 1.14.01.10. It was 1.14.00.10.
help..........
snowboarder said:
Hi,
I purchased the Softbank X01HT (post Dec) in Japan when i was working in Japan. I lived with the Japanese OS even though i don't understand Japanese because I didn't want to temper with it just incase something goes wrong and i can't use the phone. Well, now im back in Australia ... and i need to unlock it and flash a new ROM to it so that I can use it in Australia .. otherwise.. it is effectively a brick....
so.. i spent the past two days reading all the valuable information u guys provided... and in the end.. i decided to first unlock and superCID my phone using the AUTO_Unlock_v3a.bat provided by POF ... and then flash it with the Jasjam telstra ROM (RUU_Hermes_DL_UK_3[1].62.305.5_6275_1.54.30.10_108_Ship.exe) also found in this forum which received good feedbacks...
ok... after i executed the AUTO_Unlock_v3a.bat program .. everything went well... and at the end of it.. the screen even said.. successful in both unlock and superCID ... so.. i assumed that my phone is unlocked...
then... i went to flash my phone with the abovementioned jasjam ROM .. and this too.. everything went just fine ... and now.. my phone is working with this new ROM (cool! first time im able to read my x01ht coz its in English) ...
without a sim.. the OS works fine.. etc etc...
however, when i tried to put a telstra sim card in it ... its still simlocked ...
the SimLock screen comes up and requests me to input unlock code ...
so.. i did more reading and researched but can't find any solution to this ... i even tried that "unlock" code (22051978) but it doesnt work ...
Please.. can someone help me with this issue with my phone? now.. it seems that i just need to unlock my phone to use it as my jasjam ROM is working fine. Below are further details:
ROM version: 3.62.305.5
ROM date: 11/06/07
Radio version: 1.54.30.10
EtRom version: 3.62.305.116
any help/comments will be highly appreciated... thanks in advance...!
Click to expand...
Click to collapse
hey bro!when you r already flashed v3a unlock,than you should down a software name like "Hard-SPL-V7",it will help you to unlock the exrom,make you able to flash the new os\rom...
"HARD-SPL-V7" has 2 software,1st is "RUU_signed.nbh",2nd is "RUUWrapper.exe".
devileric, read post carefully. snowboarder has no problem with reflashing oses, its the sim that needs unlocking now and hard spl WONT do that...
Still reading and researching. I'd probably retry the unlock tool. it cant hurt but may work... cheers
devileric ... yes ... ultramag69 is correct ... my new English Telstra Jasjam OS works like a beauty when it operates WITHOUT a sim card. However, when i try to insert a telstra (or optus) sim card in there, there is a prompt that requires me to enter a unlock code. Please note that the unlock code 22051978 does NOT work in this case (also doesnt work in alot of other cases that i read in this forum).
Ultramag69, thank you for your help and replies, much appreciated. I actually did try the unlocking program again (three times ) . However, when i execute the AUTO_Unlock_v3a.bat when my OS is the new telstra jasjam OS, my phone will freeze on the telstra startup screen after the radio update step of the unlocking program when it automatically resets. Thereafter, even when i perform soft reset again and again, it will just freeze there. When that happened the first time, I thought that I bricked my phone .. ahhaha.. but fortunately, I was able to simply go to the tri-color boot screen and then simply flash the above said telstra Jasjam ROM. This will get me back to square one, i.e., working Jasjam OS, but phone is still sim locked.
I spent another night last night reading the applicable threads. I find that quite afew other people had the same problem as me. And I also find that whenever such problem is posted, its either ignored or a moot reply is given.
So, for the experts out there, if there is a solution to this, please kindly let me know. I am sure it will others will find it helpful too. Thank you.
Sorry wrong post

Thick Newby wanting a simple CID unlock answer

I must be thick as I have read more posts on this than I have had hot dinners and tried various utilities all to no avail although thankfully my Wizard still seems to work.
My O2 XDA-Mini s is about 2 years old and of course locked to O2 although the device come up as SIM Unlocked but CID Locked.
IPL - 2.21.0001
SPL - 2.21.0001
I am now on the Three network and would just like to get back to using the phone I love rather than the freebie I have now, so I am assuming I need to get CID Unlocked?
Having bothered to get to that stage I would want to scrap the O2 software and upgrade to a better ROM.
Sorry for being so stupid on this, I am hoping someone in the know can take the time to reply.
Thanks in advance
If it's sim unlocked you don't need to CID unlock to enable other sims.
If your new sim is rejected, then the device is still sim locked.
CID is only used for flashing, so if you want to upgrade to the better WM6 roms now available, you'd have to unlock it permanently (hard SPL) or use the Soft SPL.
Good luck,
EquinoXe
the-equinoxe said:
If it's sim unlocked you don't need to CID unlock to enable other sims.
If your new sim is rejected, then the device is still sim locked.
EquinoXe
Click to expand...
Click to collapse
Thanks for taking time to reply EquinoXe, you have confirmed what I had already thought.
The device reports "Invalid or missing SIM card" with the Three SIM card and WST v4.2.2 reports "Your phone is already SIM unlocked" ??
I do wan't to upgrade the ROM but more importantly I want to get the thing working with the Three SIM card, then I can worry about the ROM.
Any other suggestions will be gladly received.
Thanks in Advance
Download and use the LOLKWIZ03b program from these forums, follow the insturctions EXACTLY, and it will generate you a SIM unlock code.....enjoy!
ashasaur said:
Download and use the LOLKWIZ03b program from these forums, follow the insturctions EXACTLY, and it will generate you a SIM unlock code.....enjoy!
Click to expand...
Click to collapse
I have done this twice just recently but my G4 is not asking me to enter any unlock code. I read other threads where people had similar problems so tried a few times, device still comes up "Invalid or missing SIM card"
I ran EnableRapi from the device before running the batch file so I'm not sure what is going on or if it is something quirky about the G4 device??
Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.
C:\Documents and Settings\Jackson>cd\
C:\>lokiwizmsl
machinagod's HTC Wizard/Prophet/Charmer MSL Revealer v0.3
NOW WITHOUT CID Unlocking POWER!
ECHO is off.
Supports SPL 2.x!!
--------------------
WARNING: This tool is highly experimental!
I will NOT be held responsible for any problems caused by this tool.
--------------------
Thanks to xda-developers, spv-developers, and especially itsme by the work they
released. This solution would not be possible without them.
--------------------
Unlocking RAPI Please wait...
MachinaGod RapiUnlocker v1.0
Initializing.......................Done!
RAPI Unlocked.
Starting MSL work... DO NOT DISCONNECT UNTIL THIS SCRIPT ENDS
ECHO is off.
CopyTFFSToFile(0x0, 0x10000, lock_backup.bin)
ECHO is off.
ECHO is off.
SIMLock Code is your code... Type it with another SIM in...
--------------------
Lock Status: 0000000000000000
SIMLock Code: ¨~äe├ÇÔ►-┴«p¦╚.;
This exe file was created with the evaluation version of Perl2Exe.
For more information visit http://www.indigostar.com
(The full version does not display this message with a 2 second delay.)
...
--------------------
"Standing on the shoulder of giants"
Ricardo Afonso, 2005
Press Any key to Exit.
Strange, according to lokiwiz (and WST) you are sim- unlocked.
But clearly your three sim card won't be accepted.
I do remember that HTC had been messing with the bootloaders, had to downgrade one in order to unlock it too..
Could you Flash a 2.19.0001 (or earlier G4) IPL/SPL ROM and try again?
You can use dharvey4651's thread as a guide to flash the IPL/SPL.
Just ignore the carrier ROMs, and only update (downgrade) the IPL/SPL with one attached to djharvey's thread (preferably the orange, because that one worked for me).
Flashing bootloaders can damage your device beyond repair, please use this method only if you are shure about the process, and know what you are doing. I am not responseble or liable for any damages.
Flash the IPL/SPL (takes a minute), then try again to unlock the phone.
Note: WM6.x needs IPL/SPL 2.19.xxxxx at least (works great with a 2.19), so if you have downgraded to a lower number, you'd have to upgrade again in order to run WM6.x .
Good luck,
EquinoXe
Same Problem
I have the same problem as the previous post. I downgraded from WM6.1 to a WM5.1 ROM and then ran lokiwiz - success!
I have now gone back to the original WM6.1 ROM and again I am locked out from my o2 SIM.
I am using: WM6.1 ROM Prophet My Green Edition http://forum.xda-developers.com/showthread.php?p=2116170
Any suggestions?
IPL 2.10.001
SPL 2.G4.4PDA
GSM 02.47.21
OS 5.2.19.209
the-equinoxe said:
Could you Flash a 2.19.0001 (or earlier G4) IPL/SPL ROM and try again?
You can use dharvey4651's thread as a guide to flash the IPL/SPL.
EquinoXe
Click to expand...
Click to collapse
Thanks EquinoXe, I am going to try a T-Mobile, Vodaphone and Orange SIM later to see what results then maybe tomorrow try your last suggestion.
Thanks and I will post any results, hopefully not a flashy paperweight (~:
------------------------------
I have now tried T-Mobile, Vodaphone and Orange SIM cards in the Wizard and all work OK so unlocking was never the problem, obviously O2 is OK also as this was it's original branding.
So the problem is only with the Three SIM, I have an old T610 and T630 which I just put the Three SIM into with the same results.
Need to do a bit more reading on this but I thought this sort of restrictive trading practice went out with the monopolies issues, as it seems at the end of my contract it's not just a matter of me buying a phone of my choice, if I want a new handset I have to go with Three, who interestingly don't do XDA style phones, or change contracts.
More if it happens.
I'm guessing that the reason the 3 sim card won't work is because the Mini S isn't a 3G capable device - 3 is the only network in the UK that's 3G exclusive, hense why other (T-mobile, Vodafone, O2 and Orange) sims will work and the 3 sim card won't.
Hope this helps.

Need help getting my phone to work on Hutchinson Three Australia

Hey,
I was given a Softbank X01HT from my brother and I've been using the information on this site to try and get the phone up and working on the Three network in Australia. This site has been really informative and I managed to do a lot of upgrades to my phone and everything works fine except that I get "no service" when I put my Three sim card into the phone. Could someone please help me work out what's wrong with my phone?
Here are the details of my phone:
Device: Softbank X01HT (Black one don't know how old)
IPL-1.04
SPL-2.10.Olipro
ROM Version: CRCs r13.3
Radio Version: 1.47.30.19
I've done the following:
Upgrade to hard SPL (first thing I did)
Run the Hermes_SIM_CID_Unlock_v3a (Though now I have doubts that I did it right)
Installed various rom (mostly for fun)
Installed Josh V15 Manila 2D rom
Installed the dopod AUS 3network WM6 (I thought it would have the right radio and settings)
Installed the CRC rom (I didn't like the dopod rom)
Any help would be appreciated. I've been searching but I couldn't find a good answer.
I'm not very familiar with that phone but you'll need to create a new data connection so that it can connect to 3.
When creating one, make sure you select the data connection type as GPRS, 3G etc, the access point is called 3services, no username or password is required. Should be good from then on.
These forums are awesome, with a bit more patience and perserverance I finally got my phone to work.
I did more searching on the X01HT and found that people were using the radio rom from pof's SIM & CID Unlocker. There was talk about cooking roms and stuff which I didn't want to try, so I decided to just run through the unlocker again. I made sure that I turned off my phone for 10 secs at the end and do a soft reset after the 10 secs, as I was a bit careless with that part last time.
After getting through all the steps, the phone recognised my sim and configured my phone for the three network. I can now connect to the net and make phone calls.
Now the details of my phone are:
HERM200
IPL-1.01
HERM200
SPL-1.40.Olipro
ROM version: CRC r13.3
Radio version: 1.16.00.00
Thanks guys for running this site. I reckon i'll be on these forums a lot in the next few months. There's still a lot of tweaks I want to do to my phone.
Mate, bit of advice, install Hard SPL V7 so there are no "accidents" when flashing a new rom... Its a bit better at protecting your Hermes when you flash than 1.40. Thats an older version of Hard SPL.
Cheers...

Categories

Resources