I flashed my Mda Compact 2 using shell tool, for uprading to 004.4v but after few seconds i got error of cannot find temp file in the sheel tool directory and the msg that flashing ended, i hard reset my device after that it got stuck on just tmobile intro screen i tried to hard reset again but i didnt worked again, please help my device got dead.
Just go to bootloader mode and run official RUU.
I tried it but i m getting error of invalid vendor id please help
Look for noid ruu. Its somewhere around Charmer upgrading section.
Related
I've just been trying to upgrade my ROM today, I've been reading all the info on the wiki for the past few weeks, decided that i'd try, and cautiously attempted upgrading to 1.35.255
I'd already performed the unlocking and super CID, and i checked via mtty, and info 2, all was good!
Unfortunately during the flashing, the RUU kept stopping around 1% i followed the recovery steps, all was not lost, again i tried, got to 5% this time......Every time it stopped it said it had a 262 error, anyway, I'm now trying to flash the hermes via the SD flashing method (maybe what i should have done in the beginning!)
I've got my card with HERMIMG.nbh on it, and when i boot up into bootloader....it briefly flashed on the screen no image file.....
And i've just tried again, and it flashes the tri colour screen...then briefly loading.... and then back to the tri colour screen.....
When i boot up normally, it just gets stuck on the windows mobile splash screen....
Anyone offer any advice???
Thanks in advance.
JD
BEFORE POF DOES IT...SEE http://forum.xda-developers.com/showthread.php?t=286755 <--THERE
I need help, after upgrading to XDA Live Rom i decided to downgrade the radio. The flashing got interrupted cause of MSN and the device got bricked, It stops at HTC splash screen after saying NO GSM. I have tried every method imaginable to recover my poor PDA..
All I can get is to the bootloader where i got IPL-1.01 and SPL-1.09.
I've tried the microSD card thing with the .nbh file named HERMIMG, screen goes white, says loading and then checking and then back to the Tri-colour screen.. nothing done :/
Obviously i cannot get an active sync connection so some thing which i could have tried doing weren't possible to achieve.
I tried using the RomUpgradeUT but i get a porblem with vendor ID with all the ROMS and get an error 262 Update Error, I try to do the recovery thing but the PDA always boots in the HTC splash screen and gets stuck there..
Can anyone help??
can you mtty into the device?
yes.. i can.. tried following instruction and installing as in forums but no results. tried loading the .nb files but never made effect
what happens when you reflash radio rom manually ??
if you didn't have the mfg bootloader you have to use the exe files...
maybe just flash the 1.04 loader and then use the 1.27 radio updater (t-mobile)...
after that reflash the 1.01 mfg and you can flash manually ágain
could you guide me in doing that?? tell me what to download an d how to get the nb files for the radio??? plus i didn't get the hang of the mtty yet... thanks for everything
use this thread for bricked devices:
http://forum.xda-developers.com/showthread.php?t=286755
Please do not open new threads, closing that one.
After flashing my XDA2 to WM5 3.5a, i've tried merging storage & extended rom to gain memory by following a thread on Airfagev. After doing a hard reset, i found out that my phone is not responding and all i can see are black horizontal lines on the screen w/out backlight. I tried soft resetting it but still it stays the same.
Though i can still put it on bootloader mode, it also wont finish reflashing and an error message appears that goes like this:
ERROR 100: Model ID Error
The ROM image you are trying to use is not designed to work with your Pocket PC.
Is there any way for me to fix this problem? I really need help from anybody who's knowledgeable enough in solving this problem coz' i am new in this field.
Pls. help.
Thanks in advance!
Yoo can use NOID utility for flashing
HimaUpgradeUt_noID.exe
bootloader
Thank you. I can now reflash my device to WM2003 but not to WM5.I think it's because of the bootloader which is v 1.06.Is there any way to change this to v 1.03?
Help pls.
I have a mogul and have been trying to update the ROM all day with no luck, and could really use some help
I have SPL-2-2.40.Olipro bootloader working ok.
I tried to flash the radio rom 3.27.00 first, but it got about half way and errored. It then had me do the battery removal, reboot procedure and restore which said it completed ok. I then tried the rom again, but now it only goes to 9% and then the mogul resets and i get error [328] invalid command.
I then was able to update the dcd 2.2 rom which completed ok, but now I get the yellow splash screen w/ sprint logo and the no radio message. I've tried loading the radio rom again numerous times from the bootloader, but it does the same thing resetting at 9% error 328
I've rebooted the PC, played with the cable connection which seems to be working as the bootloader will switch between serial and usb.
I also tried restoring to the 2.17 rom which I downloaded from the HTC site, but it only goes 1% and errors out with the same [328] Invalid Command
What can I do to get this working?
So are u sure you have the new unlocker
then flash the rom
and then radio
I think so the file is called "Hard-SPL-MFG" and I get the red, green, blue screen that reads:
TITA100 MFG
SPL-2.40.Olipro
CPLD-9
I was able to get the dcd rom to go with no problems, but the radio rom will not go. Like I said it gets to 9% at which point the phone resets and I recieve the error 328 invalid command on the pc.
I saw some others here having the same problem, but wasn't able to find a clear resolution posted
thanks
I also just tried flashing the radio rom via sd card with no luck. I extracted and renamed the nbh file and copied it to the root of a freshly formatted (in FAT) sd card. Whne i start the boot loader I get the white screen and it says loading..... but then just returns to the red,green.blue screen. When i reboot I'm still getting the splash screen with no radio at the bottom
Put your phone in 2.40 bootloader (tri-color screen) and follow these instructions starting from step 4:
http://forum.ppcgeeks.com/showthread.php?t=17667
If that does not work, try it again from step 3.
mogul67 said:
I think so the file is called "Hard-SPL-MFG" and I get the red, green, blue screen that reads:
TITA100 MFG
SPL-2.40.Olipro
CPLD-9
I was able to get the dcd rom to go with no problems, but the radio rom will not go. Like I said it gets to 9% at which point the phone resets and I recieve the error 328 invalid command on the pc.
I saw some others here having the same problem, but wasn't able to find a clear resolution posted
thanks
Click to expand...
Click to collapse
hard set your phone(2 soft keys and soft set botton)
and then load it into bootloader(power botton+camera botton) and then try to load the radio like that
bakntyme said:
Put your phone in 2.40 bootloader (tri-color screen) and follow these instructions starting from step 4:
http://forum.ppcgeeks.com/showthread.php?t=17667
If that does not work, try it again from step 3.
Click to expand...
Click to collapse
I've tried that but I can't get the relocker to run? It says no device connected would you like to try copying again? and I'm on the SPL boot screen its connected etc
I've also done the hard reset, gone back into the bootloader and tried the radio rom again, but it stops @ 9% with error 328 and resets the phone
mogul67 said:
I've tried that but I can't get the relocker to run? It says no device connected would you like to try copying again? and I'm on the SPL boot screen its connected etc
I've also done the hard reset, gone back into the bootloader and tried the radio rom again, but it stops @ 9% with error 328 and resets the phone
Click to expand...
Click to collapse
OK, did you try starting from step 4? That means just flashing the Sprint "leaked" ROM.
if I have Alltel should I still use the same method even though it says it's a Sprint rom?
I have the same issue right now
Thank you I was able to get the 3.16 ROM loaded.
next I ran the Hard SPL unlocker and got the bootloader screen, tried the radio rom install and its still quitting @ 9% resetting the phone?
I need to get the radio to work before installing dcd's rom right?
Ok don't worry, I had the exact same problem as you mogul67 and I was puling my hair out for a day and a half.
If you read kmartburrito's original PPCGeeks page:
http://forum.ppcgeeks.com/showthread.php?t=16806
The edit by ImCoKeMaN says:
I have found that if you have issues where your device seems to be bricked and stuck in bootloader before completion of the update you can fix it by flashing via SD card.
To do this there are 3 steps:
First take the .exe file and open it with winrar. There will be a file 3.16.....nbh extract that and rename it to TITAIMG.nbh
Next format a microSD card with FAT 32 (required most are fat16 default) and copy the file TITAIMG.nbh to the root of the sd card with a card reader.
Finally place sdcard in device and reset into bootloader mode. The flash will proceed from the SD card and it should work fine. Enjoy!
Click to expand...
Click to collapse
By "take the .exe" he means open the Radio ROM flasher with WinRAR, btw... I had to think about that one for a second just because it seemed so simple
So head over to best buy and get yourself a cheap MicroSD to SD adapter, throw it in your favorite card reader, follow the steps and you'll be up in no time
THank you for your help that did it, but I was able to just run the 3.16 ROM from Windows with no sd card. After loading that ROM I was able to run the unlocker, hard spl, and then update the ROM
thanks again
Hello all,
I have an T-Mobile MDA (Dutch) that hangs in the bootloader screen after doing a wrong flashprocedure.
I tried to exit the boot loader screen with mmty and UNI_ExitBootloader, but that didn't work, so something is seriously wrong with the current rom data.
I tried to read (and understand) every similar topic on this forum to get a solution. They all point to procedures where I need to copy and run the (h)spl's, but that's impossible because I cannot boot the device.
I also tried to flash a shipped T-Mobile (NL) rom into the device. Unfortunately, the flash procedure hangs at 0% for a while and shows an error message ("connection error")
Is there a way to get this thing alive again?
More info:
Bootloader screen says:
NIKI200
SPL-1.16.0000
CPLD-4
T-Mobile MDA Plus (256MB rom) Dutch version
Some more information...
I have now tried to flash RUU_Nike_HTC_NLD_2.09.404.1_Radio_NikeMR_1.65.28.25_signed_Ship now, and this one is NOT stuck at 0%, but displays the invalid vendor id error after 1%.
I think I need this "type" of rom update, but now for T-Mobile (Dutch), so I won't get a vendor id error. I currently have a CustomRUU with the Dutch T-mobile rom (which is stuck at 0% and reports an 'connection' error message)
I also tried to flash from sd card, but it doesnt start. Do I need to rename the nbh file, because the bootloader (before the rgb screen) says "no image file" ?
I don't know what did the trick. But I have run mtty and entered the commands "set 16 0" and "set 14 0".
Then I tried to flash the Dutch t-mobile rom again, leading to the same error and a flash screen stuck at 0%.
I rebooted my device then .. and there it was.. a T-Mobile boot screen and a device that boots without any problem
Thx Tutti-frutti you are king