my jamin stuck on splash screen and i want to flash the rom
i start him with bootloader i see "usb" in screen
but when i run RUU for him .
i get connection error
why?
i have winXP
Related
Ok, i screwed up my Mini s. now i can only boot into the boot loader screen. and phone is CID locked so i can't run the r2sd command.
The question i have is this :
Can i still flash a custom rom or original rom while in bootloader mode ?
And if this is possible, can someone tell me how ?
Regards
Jacque
raymerjacque said:
Ok, i screwed up my Mini s. now i can only boot into the boot loader screen. and phone is CID locked so i can't run the r2sd command.
The question i have is this :
Can i still flash a custom rom or original rom while in bootloader mode ?
And if this is possible, can someone tell me how ?
Regards
Jacque
Click to expand...
Click to collapse
Yes you should be able to flash wizard love rom or the rom that your device was shipped with.
Just download either of these roms then put your device into bootloader mode. Make sure that the word USB is visible in the lower left corner of the bootloader screen when you plug in your usb cable. Then you just have to execute the installer of the rom that you downloaded.
If you get an error message you can use precautionary measures such as killing wcescomme.exe in task manager, turn firewall off, remove memory card, reboot pc etc.
Good Luck
Thnx for reply.
Eqx also just sent me mail and told me the same thing.
I am just busy charging the battery before i attempt another go at repairing the phone, i want to make sure that all goes smooth this time.
Will post my sucess or failure when i am done.
I just tried to flash my G4 with http://forum.xda-developers.com/showthread.php?t=293480 tutorial and of course it didn't work. I am at the three colored bar screen trying to restore my device and every tutorial I find says flash the official ROM to your device, but how do I flash a ROM to my device???
Download the official rom of your carrier,hook up the phone with pc via usb cable,watch small usb appear at the bottom of the Bootloader (RGB) screen and run the Rom,it'll start to flash.
Ok I got it working. What I didn't know was what program to use to load a ROM to my device, but I used RUU. I was having trouble with it not picking up my device but a quick PC reboot fixed that. Thanks for the help.
Hi I have a problem mtty made my touch pro before installing the hspl now to enter boost mode loader for a second I have the gray screen, blue letters says no image file and I can not load a rom that I can install hspl do? is hopeless?
hi i have a htc hero (well t mobile g2 touch) and i was follwing a guide for psfreedom which got me to install a custom recovery image and then install a .zip folder from my sdcard
m phone was fine after flashing the recovery image but after doing the .zip folder it now wont boot up
i can get into recovery but when trying to put a new rom on via sdcard it fails with this message
E:board does not support mtd utils.E:failure at line 72:
write_raw_image Package:boot.img
BOOT:
installation aborted.
i can get into bootloader but when i try to flash with fastboot it just says waiting for device and hangs there
iv tried doing this
http://forum.xda-developers.com/showpost.php?p=4467471&postcount=13
but that didnt work it just loaded up hloader and said no image found
i also tried
I found the solution!
Downloaded the RUU (ftp://xda:[email protected]_NoDriver.exe) and while in fastboot usb run the wizard!
And the hero is working again!
and that didnt work the htc application came up with the error of not detecting my phone through usb
anyone got any ideas?
Is your phone boots to the recovery mode or SPL? If it doesen't mean that it is a brick...
hubix said:
Is your phone boots to the recovery mode or SPL? If it doesen't mean that it is a brick...
Click to expand...
Click to collapse
it boots to recovery mode fine
and i dont know what spl is
Ok it's not a brick. To get into SPL press POWER+VolumeDown and give me a screenshot
Hello Everyone,
I just tried to Moonshine to turn S-OFF, but at second boot it failed, HTC MTP drivers didn't install, I updated all the necessary drivers and fastboot was also before starting the process, now my phone won't boot past first screen, I cannot turn off, I can't go to bootloader or recovery, I try to Moonshine Disterllier , but keeps giving me error "Run Disteller again and READ". its is unlocked, How can i Fix this ?
Fixed it, Just wait for the battery to drain, next reboot it boots normally
Hi. Can you tell me please where did you find the drivers and fastbbot for thr 802w?
Thx.