Related
Heh apologoies for title but im really stuck and desperate for any help!!
I have been trying to unlock my Cingular 8525 for many hours now without any luck.
I bought it off ebay knowing it was locked because I had seen these forums and knew it wasnt too harder job. I live in NZ we have a compatible 3G network here (they sell these phones branded as JasJams).
Anyway I dont have a cingular sim card, only a Vodafone NZ simcard. I dont know if that is a problem for me or not...
My problem is that I get part way through the update process and the connection between pc and phone gets cut everytime at the same place.
On my bootload screen during the setup it says
HERM100 IPL-SSPL by Des
HERM100 SPL-1.09.ds
and then
HERM100 IPL-1.01
HERM100 SPL-1.40.Olipro
Then I tick the appropriate checkboxes, I HAVE to soft reset my phone here to get it to sync up with my PC again, I dont think this should be a problem though,
It then gives me the button to select the Update button (Update the radio and bootloader)
So I click that, it gives the next screen, click next, tells you its going to take 10 minutes etc, so click next,
It then instantly disconnects the active sync connection and about a minute later I get an error screen saying the unlocker encountered communications errors.
I have been through this whole proccess 6 times now with no joy
Someone pleeeeeeeeease help me
Thanks
im willing to pay for a code all i want is a unlocked sim phone none of this radio stuff etc
try Wiki
http://wiki.xda-developers.com/
or alternatively
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=30&Itemid=27
Thanks but not really helpful, I have read the wiki through and through. I have tried that flashing HardSPL v7 and i get exactly the same problem.
PLEASE somebody help me
The only piece that is confusing is what to do once your done. The instructions say that you will be replacing your radio with a tweaked one to allow the unlock. After the entire process is done I assume you will need to have your favorite radio (1.40.3 in my case) handy to flash back onto your Hermes?
I also assume that flashing your favorite radio back to the Hermes won't lock it back again.
To be honest, I'd suggest going back to basics. You could try quite a few workarounds and end up doing this anyway..:
Reflash the original ROM your phone came with. Should be found easily via wiki.
Then you can start upgrading again.
If that's difficult, try flashing from your MicroSD card, which I've found never fails, having bricked my Hermes quite a few times now with my own cockamayme (sp) versions of ROMs that I've cobbled together from bits of code and chewing-gum.
as far as I know you dont need to CID unlock before flashing.... With olipro spl and custom RUU updater you can flash anything on your phone....
laurasaur, after you have installed 1.4 olipro, use custom RUU updater
http://forum.xda-developers.com/showthread.php?t=298737
use the RUU updater with your choice of Rom.
or if yo want to unlock the device before
http://forum.xda-developers.com/showthread.php?t=293665
amet said:
as far as I know you dont need to CID unlock before flashing.... With olipro spl and custom RUU updater you can flash anything on your phone....
laurasaur, after you have installed 1.4 olipro, use custom RUU updater
http://forum.xda-developers.com/showthread.php?t=298737
use the RUU updater with your choice of Rom.
or if yo want to unlock the device before
http://forum.xda-developers.com/showthread.php?t=293665
Click to expand...
Click to collapse
She want's to SIM-Unlock, not to CID-Unlock.
Do you use Vista? I encountered a similar problem with Windows Vista. Try a PC with Windows XP for the unlocking process.
ok my bad....
I've seen this issue with v1.4 Olipro. Upgrade bootloader to the latest Olipro 2.1 version then re-attempt.
ok thanks everyone for your advice but i am still screwed.
im not running vista.
i can not upgrade to olipro 2.1 because the upgrade utility always gets error 260 (update error) the update utility cannot connect to your PDA Phone.
I have now tried on 3 computers, my own, my parents and my work all resulting in the same thing.
I think now I will try and flash a WM6 rom onto my phone just using the olipro 1.4 and the custom RUU updater and see how I go but I dont have much hope
ok im currently updating the rom to wm6 as posted on the forums and oh my gosh i have a progress bar for the first time ever!! woot~~
um ok. now i have WM6 dopod version and fkn still sim locked someone help me before i throw my phone at the wall lol im going on holiday tomorrow and will have no phone for a week if i dont fix this in the next 3 hrs
Sim Unlock
http://forum.xda-developers.com/showthread.php?t=293665
laurasaur said:
On my bootload screen during the setup it says
HERM100 IPL-SSPL by Des
HERM100 SPL-1.09.ds
and then
HERM100 IPL-1.01
HERM100 SPL-1.40.Olipro
Then I tick the appropriate checkboxes, I HAVE to soft reset my phone here to get it to sync up with my PC again, I dont think this should be a problem though,
Click to expand...
Click to collapse
Do *NOT* soft reset your phone here, it is normal that activesync disconnects while the pda is in bootloader mode (activesync only works while OS is running). Just click "next, next, next" in the RUU and it will go fine.
woooa i think i love you Pof, I seriously do. Im not sure how I became such a noob at reading instructions but im sorry and thank you so much I now have progress bar
if you're short on time avoid any radio updates, they seem a bit hit and miss - its not worth upgrading then going away to find you've got a tossy signal!!!!
hope it worked out!
hey, im new but have read many of the pages here. i have burnt roms to my first wiz (G3) unlocked it and everything went well. i came about a wiz (G4) last week wm5 bland rom locked and want to get wm6 on it so after my research i went to the IMEI unlock site and purchased the unlock for the g4
the unlock seemed to go well the first time but, it won't come out of boot loader mode
i ran hornet o.10 for g4 it runs and completed to 100 % and then on reboot it comes up with the boot screen again
IPL 2.21.0001
SPL 2.21
i ran the tnt 1933 rom this morning and it completed 100% but still i have a boot screen
i know im missing something the battery power is fine .
i downloaded the stock rom for cingular but it won't load it has error "(294) INVALID VENDOR"
any suggestions ...
thanks in advance for your input
Airborne_Pathogen said:
hey, im new but have read many of the pages here. i have burnt roms to my first wiz (G3) unlocked it and everything went well. i came about a wiz (G4) last week wm5 bland rom locked and want to get wm6 on it so after my research i went to the IMEI unlock site and purchased the unlock for the g4
the unlock seemed to go well the first time but, it won't come out of boot loader mode
i ran hornet o.10 for g4 it runs and completed to 100 % and then on reboot it comes up with the boot screen again
IPL 2.21.0001
SPL 2.21
i ran the tnt 1933 rom this morning and it completed 100% but still i have a boot screen
i know im missing something the battery power is fine .
i downloaded the stock rom for cingular but it won't load it has error "wrong update utility"
any suggestions ...
thanks in advance for your input
Click to expand...
Click to collapse
Are you sure SPL is 2.21 and not 2.21.0001 as IPL 2.21.0001 ?
Well,if its 2.21 only,the phone's got mixed Bootloaders (IPL/SPL),IPL 2.21.0001 are G4 and SPL 2.21 is G3,I don't know how you got it,but your phone is 'Bricked'
mmm it figures
so it appears there could be a problem with the imei program,
as i said it never came out of boot mode after the unlock
and no errors were shown ...
i could get another and replaced the main board, this one is in new condition
except for the custom bricked rom . in the future i will not play with a g4
thanks for the diagnosis, no way to flash a new spl / ipl ... i did read that if
it booted you could get it back in some chance cases .. i am curious as to how this happened (others not doing this for a hobby could brick there only phone)
step 1 - ran imei unlock
never came out of boot mode after
2- flashing the to above roms said to be G4 safe
i never look to see what the ipl / spl were before
i looked with the wizard tool but didn't save it
well you live and learn, it's good for parts now off to ebay for another crack at it ...
thanks everyone ... the best thing about this phone is everything you can do to it
with help from those who know ...
I recommend trying to flash back to original service provider ROM, then unlock again and try another. As long as you can get to bootloader (tri-color screen), there's still hope for your phone. When it's in this mode, and you plug in the USB, does it say USB at the bottom of the phone screen? If so, you are not dead yet.
Custom build wm6 roms like TNT etc... never Brick a G4 phone as no IPL/SPL is included in them,they are completely safe for G4 devices.What I can gather,it must be the wrong imei unlock code perhaps.
Well,like Myrddin Wyllt said,there's no harm in trying,so if it gets into Bootloaders,try to flash the official rom and if there's an error "wrong update utility" ,replace the RUU in the rom with this RUU and run this RUU,hope it might work.
Myrddin Wyllt said:
I recommend trying to flash back to original service provider ROM, then unlock again and try another. As long as you can get to bootloader (tri-color screen), there's still hope for your phone. When it's in this mode, and you plug in the USB, does it say USB at the bottom of the phone screen? If so, you are not dead yet.
Click to expand...
Click to collapse
yes sir i can talk to the phone from xp pro ..
USB does come up
so i can swap the RRU with the nbf file i need ...
no file name change required on the xxx.nbf file
thanks alot for the(schooling) advise ... i was going to need to brick another to make some book ends... this could save me that
stuck
Airborne_Pathogen said:
yes sir i can talk to the phone from xp pro ..
USB does come up
so i can swap the RRU with the nbf file i need ...
no file name change required on the xxx.nbf file
thanks alot for the(schooling) advise ... i was going to need to brick another to make some book ends... this could save me that
Click to expand...
Click to collapse
ok, i swapped out every RUU i could find i get errors from
read file
invalid vendor id
wrong update utility
im too new to figure this out ..can you extract a ipl / spl from an
official rom and then flash that to get the boot loader's back in sync
i found the att 8125 ipl /spl nbf when i flash, it runs to 100% reboots but no changes
anyone have a link to flashing just the ipl / spl on the g4
i am most thankful for any advise ..
try running the hardspl on phone, it might just work to revert it back to a G4 spl.
Link to HardSPL : http://forum.xda-developers.com/showthread.php?t=332320
and G4 ipl and spl here : http://forum.xda-developers.com/showthread.php?t=342744
Also I paid to the IMEI Check and I had to change the plate because the PDA died as yours. E had not returned to the money of the IMEI Check only reply to me was that it had to change of plate ..... It had the unblocked CID?
bastards
yes they won't return my money ... somehow they bricked my phone
i would use the hard /spl and not the imei those guys are assholes
Hey, my phone is an At&t 8525 and after finally fixing the white screen problem and flashing hard-spl v7 and a couple of roms I bricked the phone when flashing the last touch flo rom. During the flash the ruu wrapper stopped and indicated there was an error. I did the recovery and it supposedly completed succesfully if I can remember right. When it reboot it would not get past boot loader. And thats where I am now, the phone will not get past boot loader.
I've tried every method on these forum I could found
SD card flashing dosent work, I get the 002..... error in red.
Flashing the factory an at&t rom dosent work either, gets the same error
\
As for as I know the MTTY method dosent work, I don't know how to type in commands into bootloader and when I type in 14 0 in MTTY nothing happens
KITL is not enabled
IPL-1.04
SPL-2.03
The phone does not boot into bootloader when I hit the power button, I have to hold the comm button, power button, and soft reset in order to bring up bootloader.
When bootloader is up and the phone is connected to the computer via usb bootloader displays usb on the screen and windows detects the device as an HTC device.
Again i've spent about a week and a half trying to fix this phone and I don't know what to do anymore, i've tried more methods than listed above I can't remember though. If anyone can give me a hint on what to do I would highly appreciate it. Thanks
P.S Can someone please tell me how you type commands in bootloader or MTTY
You DON'T have Hard SPL V7 installed..... Otherwise your SPL would be 2.10.
Connect the Hermes to the pc, make sure active sync has benn disabled - got to settings, untick connect by USB. It should register on the pc. Go to bootloader then run the .nbh file for your stock rom... Make sure its the carrier rom that it was shipped with. It doesn't have to be WM05 but it DOES have to be your ORIGINAL carrier rom. Let it run through, you may gewt lucky.....
If it works, INSTALL HARD SPL V7....... Makes it so much easier to fix then...
Good luck...
Thanks for the reply, much appreciated
I tried downloading and sd card flashing a stock rom from a list of factory roms of all Hermes that I found here on xda. It gave me the same error though. I'm not exactly sure which exact rom to download from that list either. Any more help would be appreciated, thx
Wow I feel retarded, I used the wrong factory rom. After I used the right one it worked perfectly, I now have my 8525 back! Thx so much man, ur the friggin man!
Congrats bro you got it atlast. good luck & take care your baby in future. try to help others with your experience.
Glad you fixed it mate, but if I were you I'd also make sure you have Hard SPL V7 installed. It is the safety net to help when things go wrong... Never gonna be 100% safe but better odds with Hard SPL V7...
SPL - 2.10 oli
Cheers...
Ok... Rejoining the 8525 Clan
Is this Forum still alive???
Been a while guys, figured I would break out the 8525... charge it up and see what kind of things are new in this community. Unfortunately, it looks as if the radio is bricked on it. Seems like it will install ROM's that the radio is not included on. NO GSM is on the boot display, which is strange as I was using this phone until I got the Tilt about 1 1/2-2 yrs ago. I was a hardcore flasher back then... every other day it seemed, so I know it has (or had) everything it needed like the Oli 2.10 SPL... but it seems like I cannot recover this radio issue.
I am messing with the different original OEM and Carrier ROMs hoping I can get passed the 11-12% mark, and I will let you know if something changes. Any idea if un-installing SPL 2.10 Oli, and then trying to walk back through the old SPL steps could help? I am just trying to figure out another way to get around this radio issue... or basically I have a PDA, no phone Damn phone hasn't been touched in like 2 years, you think it would be just as fine as it was when I took the SIM out.
Cheers
Can u plz tell me how do you fix the white screen problem ?????
kashifmehmood said:
Can u plz tell me how do you fix the white screen problem ?????
Click to expand...
Click to collapse
Please try searching before posting.
Your answer lies within
Thread closed
I got an iMate JASJAM from my father awhile back - a great hand-me-down if you ask me!
It's currently running Windows Mobile 5 w/ default just about everything.
HERM100
IPL-1.01
HERM100
SPL-1.11
Anyway, onto my problem.
I'm using the Hard SPL upgrade files found in Olipro's thread.
I run it and it works up until I select "Yes" on my device.
It then reboots into the bootloader and just sits there and does nothing until finally the installer throws an error 260.
Anyone else had this problem?
Is there a simple fix?
If it makes any difference, I've got a Mini-SD card in it. 512mb.
Go to the Hard SPL thread, page 116, post 1160. It tells you (and gives all apps needed) how to install using the SD card... Gets rid of those pesky sync problems.
You can use the sad card method to upgrade your os too, just drop the steps using sspl.exe....
Cheers...
wonderbreadz said:
I got an iMate JASJAM from my father awhile back - a great hand-me-down if you ask me!
It's currently running Windows Mobile 5 w/ default just about everything.
HERM100
IPL-1.01
HERM100
SPL-1.11
Anyway, onto my problem.
I'm using the Hard SPL upgrade files found in Olipro's thread.
I run it and it works up until I select "Yes" on my device.
It then reboots into the bootloader and just sits there and does nothing until finally the installer throws an error 260.
Anyone else had this problem?
Is there a simple fix?
If it makes any difference, I've got a Mini-SD card in it. 512mb.
Click to expand...
Click to collapse
i got your problem on my i-mate jasjam too,
have u solve the problem yet?
i face the same problem
Well I flashed maybe 30 HTC Tytn PDA`s (I work in service) and never bricked any... I never putted cooked roms,bcs this roms are stupid.And a lot of cooked roms use much more ram and many of them have simple appcliations,which you can to install alone... So,my advice for peoples : Use official Win Mobile 6 rom from HTC ftp server.You can find links in this forum also...And yeah I dont need HARD SPL for official... never bricked.
Depends slaki85 if the Hermes has been Branded... For example, I have the Telstra rom on my Jasjam, if I tried to put the HTC official rom onto it, I'd have a brick... The carrier rom prevents me putting any other rom on it other than theirs.... And it ALWAYS has a heap of bloatware.
You also can't put wm6.5 on...
Hard SPL allows me to put other roms, cooke or official, that I can't put on without ending up with a brick.
As for the guys who can't put Hard SPL on, use the sd card method as I said before. Its easier, means there's less chance of a brick and takes 2 secs...
ultramag69 said:
Depends slaki85 if the Hermes has been Branded... For example, I have the Telstra rom on my Jasjam, if I tried to put the HTC official rom onto it, I'd have a brick... The carrier rom prevents me putting any other rom on it other than theirs.... And it ALWAYS has a heap of bloatware.
You also can't put wm6.5 on...
Hard SPL allows me to put other roms, cooke or official, that I can't put on without ending up with a brick.
As for the guys who can't put Hard SPL on, use the sd card method as I said before. Its easier, means there's less chance of a brick and takes 2 secs...
Click to expand...
Click to collapse
Yeah,you are in right with 6.5 WinMo...I really tryed before Win 6.5,and expect few visual changes,he dont have anything new..With 6.5 or 6.5 + Manilla-TouchFLo,TyTN is very slow...what to say about ram memory...sometimes and 15 MB more busy...I understand that peoples always will put new rooms,I only dont understand why peoples risk...Expect if some win dont have some big changes.byw if someone want to put official HTC 6.0 rom,I tryed many times with 100% sucess in HTC TyTN and SPV M3100 (also TyTN but from postpaid Operators)..
I also agree that is HARD SPL good sometimes.I only dont understand why peoples change roms... : P especially custom roms...(few apps more and speed,ram slower...).But probablly I am subjective : )
Again, if you have a carrier rom they tend to overload it with bloatware, software and apps that use their sites. It tends to slow down the hermes and, truth be told, I've started with less than 15Mb ram using the stock rom... When you have that happen, cooked roms are a much better alternative. Also, if you use the apps cooked in it means you don't have to hunt down the cabs yourself....
Much easier....
Hi all you enthusiastic wizards!
I wonder if there is still a anyone out there with a passion for Hermes 100 / I-mate JasJam ...
I have been following all sorts of threads in an attempt to give my JasJam a new life. Have tried to flash your Hard-SPL-V7, SSPL-Herm, RUU_HER_6.20.100.0_0.00.00.00_XDA_WWE_XBOW_Custom etc. Unfortunately no success at all ... at least, I suppose I can call myself lucky to not have bricked mine in the process.
Can anyone possibly direct me to an "up-to-date" thread which gives me clear step-by-step instructions on how to up-date my gadget and give it a "new life"? I am technically minded, but I am certainly not an expert when it comes to these matters.
The details are:
Herm 100/JasJam
Windows Mobile v 5.0 - OS 5.1.195
ROM verion: 1.31.30 5.2
ROM date: 09/08/06
Radio version: 1.21.31.10
Protocol version: 32.53.7020.01H
Ext ROM version: 1.31.305.104
Thank you so much for your help!!!
Herm100
I myself am trying to do something to this phone. This is my first time flashing a phone and im not too worried about bricking it since its an old phone.. I think i got the Hardspl up but i cant seem to get past the tri-colored screen.. i would like to work together with you if u want
Hi pyramidseeker,
I found out that my problem was that the USB disconnected everytime I attempted to flash any Hard-SPL and therefore always got stuck on the tri-color screen. Is that what happens to you? If so, here is what worked for me:
I found and flashed the Hard-SPL-V9 (in this forum). For some reason it works and does not disconnect in the process.
Once I have done that, I was able to flush Pays_WWE_305_Final_Full, and I assume, you can flush any other RUU you like.
Hope this helps you - it helped me ...
Thx that did work i put the black ver. on my phone.. now i want to try to use my computers net connection to connect on the device i think i can do that... i would like to know what programs u use that r cool.. lemme know... thx again it went like clockwork with the ver.9
i installed activesync 4.5 now i can use my comps connection like a LAN.. sweet.. do u know of a way to watch youtube videos or am i limited to flash?