Related
Hi!
long time viewer first time poster.
I have G4 CID LOCKED Cingular 8125 with mfrazzz's Crossbow Reloaded 1.7.1 I have wizard love Rom as Base.
I really tried hard to update (I guess it is really a downgrade) my original Radio from 02.25.11 to 2.19.11 but no matter what I do, it failed.
I tried with every romupdateutility_wizard_noid.exe i could find but I get the same result everytime.
ON PC: I get 260 Error (tried in two machines same error message)
and
On my Wizard: stuck in this 3 colored screen. I see 3 color screen with "RUU" in right upper corner and "USB" on left bottom with IPL/SPL version showing in red If i press reset button, it will boot back to mobile windows fine.
Can anybody help me?
My rest device info:
ROM Version: 2.18.0.0 WWE
ROM date:2/14/06
IPL/SPL: 2.25.0001
GSM:02.25.11
Protocol version? 4.1.13.12
ExtROM version: faria V5.0
My Downgrade
All I did was use the rom upgrade utility from the "wizard love rom" (the one that is in Italian) and the T-mobile radio rom listed in the Wiki.
Worked like a charm!
thanks for the reply..
but of course i tried that already.
i think error 260 is communication related issue. PC communicate perfectly with ActiveSync.. but when it reboot for the flashing to occur,it just get stucked as if pc is not communicating with the wizard.
is downgrade to 2.19.11 really worthy?
nic2mit said:
thanks for the reply..
but of course i tried that already.
i think error 260 is communication related issue. PC communicate perfectly with ActiveSync.. but when it reboot for the flashing to occur,it just get stucked as if pc is not communicating with the wizard.
is downgrade to 2.19.11 really worthy?
Click to expand...
Click to collapse
Is your device actually booting up? If so, just download one of the radio ONLY roms. It won't matter whether you have a CID locked phone or not and the radio ONLY rom will not touch the IPL/SPL.
Having said that, is there a reason why you want to downgrade to 2.19? Are you having missed calls issues?
Hi titus666,
I am having the same ROM and missed call issues too.Even when i am on a full coverage area my wizard signals seems to dropping,coming back,dropping ....
What could be the probalem .Any recommended Radio ROMS's.
Probably you read this already
xdawiz said:
Hi titus666,
I am having the same ROM and missed call issues too.Even when i am on a full coverage area my wizard signals seems to dropping,coming back,dropping ....
What could be the probalem .Any recommended Radio ROMS's.
Click to expand...
Click to collapse
A little bit off regarding your initial post but here´s good feedback on how both radios behave.
http://forum.xda-developers.com/showthread.php?t=312834
I've had some problems as well.
I used the tool that came in the download to downgrade to 2.19 (I am having missed calls problem) and it won't.
I'm using a Windows Vista and already did the whole thing to update drivers with the one given on the forum over here, yet, everytime I run the thing it crashes and then I have to go through it all over again.
Its like the driver just doesn't work anymore, even though I have tried "re-updating" it to the one that I downloaded here, unlike the real Roms this one just won't go throguh and wait for the 3 colored screen to come up, just freezes before.
I was trying to upgrade to radio v1.43 in the hope that battery life was improved over 1.41 however when it got to 8% it stopped and gave me an error i can't remember After atempting to recover, it got off the three colour screen now the 3100 stalls on the blackshadow version4 screen (bootloader screen?) and goes no further. I tried reflashing but got a 260 and using mtty, only getting 2 com port options, didn't offer any help.
I'm really sorry to have not been able to sort this with reading through the relevant post but I haven't found a solution. What else can I try?
Hi,
Could you pls advise what is your device made, model, SPL version ... etc.
Also did you try to do Hard reset?
I'm using now black MAJIK (and few days ago black shadow) with radio 1.43 with no problem.
its the SPV m3100 When I decided to go Black shadow I read up on mr vanx and made sure I had all the things I needed. If I remember right, when I came to upgrade to Majik the auto detect found the second option down
SPL-1.04/1.10 - 1.09 Bootloader. I've realized since I had a spaz and ran the RUU from the archive this time. From what I've since read thats not too cleaver.
I have tried a hard reset and took the battery out instead of pressing space.
I dont know if this information on the starter screen is of use
M 05
S 04
B 05 D 3lak
I'm not sure, but hard reset doesnt mean you take the batery out.
Please check that link:
http://wiki.xda-developers.com/index.php?pagename=Hermes_For_Beginners#hardreset
I was in your position (hanged on booting) few days ago, and when i did hard reset, it changes every thing to basic normal condition.
i meant when i did a hard reset when it asked me to press space to reboot I took the battery out. I tried again this time pressing space to reboot but I still get stuck on the loading screen. I can't connect by USB to the PC I'm guessing the drivers on the phone haven't loaded and I'm stuck as to what to do.
Does anyone have any ideas?
try look at it http://forum.xda-developers.com/showthread.php?t=286755
ok I've tried everything I can think of to connect the 3100 to the computer so I can reflash it but mtty gives only com 1 and com2 but no USB and neither those two work, active sync wont connect so I disabled it as suggested and running the radio ruu and wrapper wont querry the device. I am now at a loss as to what to do next someone must know what I should do. Please?
what is your SPL?
try this http://wiki.xda-developers.com/index.php?pagename=HTC_Hermes
sl is 1.09 i'd updated it on the previously successful black shadow flash
msn [email protected]
icq 150277111
AIM TazmanFH9
Yahoo bigfathairyboggart
I have tried changing KITL trasport but I am unable to select or chose either option. I have also tried the rversion command in the tri colour screen but nothing happens. I hope I'm missing something nice and simple but I get the feeling I'm not going to be that lucky. Please help
tcSPVm3100 said:
sl is 1.09 i'd updated it on the previously successful black shadow flash
Click to expand...
Click to collapse
I suggest you check again, press and hold the side OK button and the power button...then put the stylus into the hole in the bottom of the unit.
yeah I've done that it's "SPL-1.09"
I had this exact problem yesterday, with the same bootloader too. The phone would not pass the splash and IT refused to upgrade. I ended up downgrading to a shipped wm5 rom (in my case the cingular 1.30.502.1_1.11.00.00) which to my surprise actually worked as no rom radio or spl upgrade moved at al on my phone. Then upgraded back to black majik. I hope this helps.
Thanks. I downloaded the trial of wm5 from the windows website and it asked me to install .NET framework version 1 so I got that but it turns out to be 2.0 not 1.1 It would say it had repaired but it would say this with or without the phone connected.
tcSPVm3100 said:
Thanks. I downloaded the trial of wm5 from the windows website and it asked me to install .NET framework version 1 so I got that but it turns out to be 2.0 not 1.1 It would say it had repaired but it would say this with or without the phone connected.
Click to expand...
Click to collapse
Just download a WM5 ROM from the wiki page!
ok tried this too no luck.
Trying to use the one from orange (linked to through wikki) I get an 294 invalid vendor error however active sync cannot connect yet of course so is this to be expected?
I have however gotten a connection with mtty which is a step forward dunno what to do with it yet though except trying the password 0000000000000000 command but it not disabling the password. This then lead me to read for a further hour how to change it and I've got to be honest; it beat me. I have No idea what the hell its talking about. My head hurt with so much reading.
I get a no gsm pop up v briefly on loader. I so want my phone back
I have since tried CID unlocker just so i get something installed onto this brick but I either get a connection error or it telling me it can't install for some other reason. I can not set the password in mtty to 0000000000000000 so how do I do that and is this the first step to getting things sorted? "just running a rom install" is not happening I can get a USB connection in mtty and that is it. Is the fact i'm running SPL 1.09 a problem? I'm getting precious little help guys If i'm posting in the wrong place or something please let me know. I need thing thing back now. Hours are drifting by with me trying to get some head knowledge but I still need some guidance please
tcSPVm3100 said:
I have since tried CID unlocker just so i get something installed onto this brick but I either get a connection error or it telling me it can't install for some other reason. I can not set the password in mtty to 0000000000000000 so how do I do that and is this the first step to getting things sorted? "just running a rom install" is not happening I can get a USB connection in mtty and that is it. Is the fact i'm running SPL 1.09 a problem? I'm getting precious little help guys If i'm posting in the wrong place or something please let me know. I need thing thing back now. Hours are drifting by with me trying to get some head knowledge but I still need some guidance please
Click to expand...
Click to collapse
can u flashing HARD V7?,i think better u have IPL 1.04 SPL 2.10olipro first ,then try to flashing radio?
and did u try SD card.
In bootloader can anyone here connect with active sync? I can't so updating rom and radio flashes in the usual way isn't possible. Trying the hard spl again it tells me to make sure active sync is connected and as it isn't it throws back a 262 update error. 0% on the hermes and that's currently as far as I can get. I have no means with which to access the memory card.
The reason you get an invalid vendor ID is because your CID doesnt match....download a ROM which is for your device (an orange one?)...then try.
You need to read the wiki alot more before trying anything else since you are not aware of the vendor ID error...nor the fact you MUST use HardSPL.
I linked to the orange ROM from wikki and tried installing it. it was while installing THIS ROM SPV_M3100_ROMUpdate_0407.exe I got invalid vendor error.
Installing a recent DL on HARD spl v7 I get a 240 open file error that's one I haven't had before.
With all other attempts they all say they want an active sync connection.
I can not connect to the phone through active sync
so all attempts by me to flash anything to the phone using an RUU fails.
All rite here we go, in advanced i thank u guys for trying to help me out here.
First, i'm a n00bie compared with the most of u guys.
My Device:
Tytn Herm 300
OS: Schaps Purple 3.30c
SPL: Hard-Spl 2.10 oli
Radio: 1.16.00.00 !Hmzz...that's the problem!
My phone functionallity sucks...some how it keep loosing connection while i see the phone indication bar up to 3 bars. So i decided to do something about it.
Beeing a noob i thought it got to do something with the OS. So i upgrade it to Schaps's wonderfull purple WM6 Hermes 3.30c and loaded the Hard SPL 2.10 oil V7. All went great, and my Hermes never looked so cool before.
But now i'm trying to upgrade my radio, which is still version 1.16.00.00, to what ever better version. I tried every radio upgrade possible from this list:
http://wiki.xda-developers.com/index...actedRadioRoms
Every single one starts well. passed the information retrieving from my phone. Confirmed the update, and then there was the installation progress bar....
All versions of the radio roms i downloaden get stuck in here. It doesn't even start..0% and error... And really i dun have any idea why.
So after re-flashing a gazillion times, i decided to ask help to the allmighty XDA community. So pls, if anybody there got a suggestion or the solution...i would be so thankfull and will slaughter a goat to worship you
If you've got schaps Rom and HardSPL on your phone then you obviously don't have problems flashing or with PC/phone comms.
When you try flashing the radio, how long do you wait before deciding it doesn't work? I've found that some of them can take what seems like a really long time and I'm tempted to unplug and start again.
Maybe try again, then go make yourself a cup of tee/coffee or get a beer then come back 10 minutes later. If the upgrade still hasn't worked we'll have to look a bit deeper
RaDeNRFX said:
- I am so sorry posting this twice in the wrong sections, it seems that i'm a really noobie forum user - But i finally found the rite section. So my humble excuses.
All rite here we go, in advanced i thank u guys for trying to help me out here.
First, i'm a n00bie compared with the most of u guys.
My Device:
Tytn Herm 300
OS: Schaps Purple 3.30c
SPL: Hard-Spl 2.10 oli
Radio: 1.16.00.00 !Hmzz...that's the problem!
My phone functionallity sucks...some how it keep loosing connection while i see the phone indication bar up to 3 bars. So i decided to do something about it.
Beeing a noob i thought it got to do something with the OS. So i upgrade it to Schaps's wonderfull purple WM6 Hermes 3.30c and loaded the Hard SPL 2.10 oil V7. All went great, and my Hermes never looked so cool before.
But now i'm trying to upgrade my radio, which is still version 1.16.00.00, to what ever better version. I tried every radio upgrade possible from this list:
http://wiki.xda-developers.com/index...actedRadioRoms
Every single one starts well. passed the information retrieving from my phone. Confirmed the update, and then there was the installation progress bar....
All versions of the radio roms i downloaden get stuck in here. It doesn't even start..0% and error... And really i dun have any idea why.
So after re-flashing a gazillion times, i decided to ask help to the allmighty XDA community. So pls, if anybody there got a suggestion or the solution...i would be so thankfull and will slaughter a goat to worship you
Click to expand...
Click to collapse
ach2 said:
If you've got schaps Rom and HardSPL on your phone then you obviously don't have problems flashing or with PC/phone comms.
When you try flashing the radio, how long do you wait before deciding it doesn't work? I've found that some of them can take what seems like a really long time and I'm tempted to unplug and start again.
Maybe try again, then go make yourself a cup of tee/coffee or get a beer then come back 10 minutes later. If the upgrade still hasn't worked we'll have to look a bit deeper
Click to expand...
Click to collapse
I waited till the Program says connection error...and send me to recovery proces. And i've been making hella tons of coffee after trying to flash that many Radio Roms. Any other suggestions? I'm so desperate
Ok, maybe some more info...
Do you see 'NO GSM' during the phone boot process?
Do you have no radio at all or just intermittent reception?
Are you running Vista?
What is the connection error number?
If you've lost the radio but have hard SPL it may just be a case of re-flashing an original manufacturers ROM (which will include the radio) then start your upgrading again afterwards. Don't forget to back-up data before flashing.
If you do flash a manufacturers shipped rom - check that you still have HardSPL afterwards.
ach2 said:
Ok, maybe some more info...
Do you see 'NO GSM' during the phone boot process?
Do you have no radio at all or just intermittent reception?
Are you running Vista?
What is the connection error number?
If you've lost the radio but have hard SPL it may just be a case of re-flashing an original manufacturers ROM (which will include the radio) then start your upgrading again afterwards. Don't forget to back-up data before flashing.
If you do flash a manufacturers shipped rom - check that you still have HardSPL afterwards.
Click to expand...
Click to collapse
Well the weird part is "No GSM" appeared occasionally...some times it shows it sometimes it's not showing it.
No...i'm a Vista hater. And dun have the original manufacturers ROM. I've got the "T-Mobile Vario II" from The Netherlands..so if anybody got a link for the original version i'd be thankfull.
The Radio it self is intermittent and very inpredictable...for example:
Radio indicator says i got full recieve:...but i can't call or recieve any.
Connection error: 262 (which is, if i'm not mistake a connection error.) Which is bull cuz i'm re-running every other ROM's upload with the same way and succeded/
Radio indicator says no reception and shows an exclamation mark:...and my GF just called me to hurry up and pick her up :/
But the weird part is...it seems that my radio ROM is locked somehow. I can upgrade or downgrade SPL's and OS ROM's but not the Radio ROM.
I've tried to use MTTY by now and followed the manual bellow: (Problem 5)
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#problem5
But it began with invalid password. Procede as written and it didn't helped.
More suggestions are welcome
My bad...i didn't looked well enough. It is saying No GSM the whole time.
More information:
I've checked the Device information on the Hermes now some information are blank:
Radio: Blank
Protocol version: Blank
IMEI: Blank
All other information field are filled. Been spending hours reading tutorials and manuals...and nothing. HELP!
OK,
This isn't a problem I've had myself, but loads of other people have and there are quite a few threads on how to unbrick from here... you're going to have to do a bit of reading.
This page shows the different combinations of OS/radio/brick type etc and should point you in the right direction for the correct course of action http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
Then read through this thread http://forum.xda-developers.com/showthread.php?t=286755 . It's got really long but read the beginning where POF describes the types of problem and also the solutions. Then it's probably best to jump to somewhere near the end and pick someone who has a similar problem.
It sounds to me as though you need to just flash a radio in nbh format, but please do some more reading before you do this to check my advice - as I said at the beginning, I haven't had this problem so I'm only giving advice from what others have written.
ach2 said:
It sounds to me as though you need to just flash a radio in nbh format, but please do some more reading before you do this to check my advice - as I said at the beginning, I haven't had this problem so I'm only giving advice from what others have written.
Click to expand...
Click to collapse
I am really thankfull of ur post. Unfortunately, i've been doing some reading. Including the link u gave me. The problem is that i can't upload/flash Radio in nhb format.
As i described in the first place, i can't load a nhb format radio in RUUWrapper.exe properly. It can start the proces..but it always end up with a connection error code 260/262 during the installation progres bar (0%).
The solutions some ppl tried in ur link is often not my case. And the similar cases i have tried where i end up with the same grumpfy situation.
have you tried to flash the radio using the SD card method? I too have a cable connection problem but I fear mine may be hardware failure.
Yap...and no luck
hi all,
i have recieved a hermes with boot loader screen (tri color) when i try to switch it on it goes directly to 2 color screen doesnt go further at all. I've read the sticky thread . As the phone which i have shows on screen the following
HERM100
IPL-1.04
HERM100
SPL-1.40. Olipro
thats it nothing else exept tri color screen so read the sticky threadabout how to unbrick hermes and did following options when i flashed tmobile uk rom it goes further but it stucks at 11% and doesnt go further and when i try to flash a rom which has 1.04 (528420-ruu_hermes_1[1].18.255.3_1.18.255.108_1.03.03.10_qtek_wwe_ship) but it doesnt do anything with phone, it cant even detect the phone and give error straight away can anyone please guide me what should i do further to alive this phone
UPDATE - To easily unbrick type 2b (on T-mobile UK) - please flash with wm6 test from t-mobile @ http://forum.xda-developers.com/showthread.php?t=322905
SPL HTC_BOOT Boot OS? No GSM? KITL Diagnostic Solution
1.04 Any No No --- Bricked while flashing OS, radio intact Flash any shipped ROM with bootloader 1.04 on it 2 times (1.04 bug)
hi no reply but 53 views any mod plz help
WHaT YOU MEAN?
by:
UPDATE - To easily unbrick type 2b (on T-mobile UK) - please flash with wm6 test from t-mobile @ http://forum.xda-developers.com/showthread.php?t=322905
SPL HTC_BOOT Boot OS? No GSM? KITL Diagnostic Solution
1.04 Any No No --- Bricked while flashing OS, radio intact Flash any shipped ROM with bootloader 1.04 on it 2 times (1.04 bug)
---I think your hermes is bricked if you cant upgrade even a stock rom is bricked dude...
For the last thing you could do about it... flash a stock rom like ATT stripped you can find it on the WM6 subforum here on hermes forums... all the chefs put in the main post the link to it... if it doesnt works so... you are screwed up...
be sure ahave this:
Battery at 100% at least 60%
XP pc not vista not wm7 ok?
A nice usb cable and nice USB ports too on the XP pc
Dont run anything till it finish and... dont flash with SIM card and microSD inserted.
Go ahead and post your results again.
hi thanks for your reply i have tried these 2 following roms
HTC_TyTN_WWE_3[1].54.255.3_6275_1.48.00.10_108 (stucks at 12%)
RUU_Hermes_CINGULAR_WWE_3[1].62.502.3_6275_1.54.07.00_108_UOOS_SVN05_Ship (stucks at 11%)
with these its not really working anyother thing which u think i should do
br
Sounds like the radio rom is corrupted. Flash a Stripped Stock rom (no radio) . This should get you back up and running windows but it doesn't look good to get the phone running again...
mmmm
Sounds like your batt is almost dead... maybe it shows... 70% but drains to fast is lying to you... or your cable is broken somewhere...
you can DL the stock stripped here
http://www.4shared.com/file/61372397/e2bf76c0/official_ATT_WM6_striped.html
ultramag69 said:
Sounds like the radio rom is corrupted. Flash a Stripped Stock rom (no radio) . This should get you back up and running windows but it doesn't look good to get the phone running again...
Click to expand...
Click to collapse
yes u r right mate my phones radio rom was corrupted and thanks to + Que PPC for providing help and link of the official AT&T WM6 striped rom which turned my phone back to normal but the problem is when i went to device information it says like this
ROM version: 3.62.502.3
ROM date: 10/11/07
Radio version:
Protocol Version:
so radio and protocol versions are blank nothing is there so can u please tell me wt should i do to solve this or its not solvable at all thank you very much indeed to you guys. I really appreciate it
br Sherry
Not solvable... You might like to try running your SHIPPED STOCK Radio Rom, if you know what it is, but there isn't much hope of recovery once the radio goes... Look at it this way, couldn't hurt....
Hi guys,
Mods - first time post and im not a regular user so if im breaking the rules i apologise. I have spent hours already trawling the forums, but i am now admitting defeat and I need your help!
My Problem:
I have an x7501 SPL 1.06 0000, WM 5.0, GERMAN OS
I want to upgrade this to WM6.1 ENGLISH
I dont care what the SPL is, as long as it works, is reliable, and wont disable any standard WM functionality
I am not interested in tweaks, hulks, or other (non standard) tricks, i just want to get the device running a stock WM 6.1 rom
That said - if you guys think that going to 6.5 is the best (non beta, no risk) option, then im quite happy to go that route.
$50 reward to the first person who provides the following info IN A FORMAT THAT I CAN UNDERSTAND. im good with computers for a non pro (and can follow instructions , but this is just over my head!
I Need:
1) Link to an unlocker and instructions how to use, that will give me the required SPL (note my SPL is 1.06 - will this require two SPL flash steps??)
2) Link to a stable ROM that retains all windows functionality, and instructions how to use it.
If i find that i used two or more peoples help i will split the reward accordingly!
thanks in advance and keep up the good work!
Alan K
First you need to download the unlocker from this thread and follow instructions... http://forum.xda-developers.com/showthread.php?t=315831
This will give you SPL 1.2
Here is a handy thread with step by step instructions on upgrading your roms you should read through before beginning to flash...http://forum.xda-developers.com/showthread.php?t=429013
Unfortunately, the stock-like wm6.5 roms made by michy-prima that ran on spl1.2 are no longer hosted on any sites anymore. I can try to contact him for you and see if I can get a copy directly from him. I will see if I can do that.
Otherwise, you can change your spl to 3.5, which you might as well do anyways, as there are more roms for that spl and even the stock-like michy-prima roms were made in spl3.5 also, so if I can get those, I will get the spl 3.5 versions.
So to then change your spl to 3.5, you must have first used unlocker to make spl 1.2, then the only way that was made to change spl to 3.5 was to flash the Athena Project 4 rom, so go to this thread... http://forum.xda-developers.com/showthread.php?t=387409 and download the AP ROM V.4, unzip it, and run the flasher while your phone is connected with active-sync to your computer. This will install the spl3.5 and the AP4 Rom.
Now that that is done, you can choose any SPL3.5 ROM to flash... (make sure to only flash SPL3.5 Roms now... if need be, there is a way to go back to SPL1.2 if you need to, but there really is no reason you would need to.)
Probably the most modern rom with the most features would be the AGB Version 3.00 ROM, The Hulk one (I know you said you didn't want that, but it is the most current rom, and you can easily change the theme and wallpaper on it. This is the ROM I have on my Athena... its a nice ROM.) Here is the thread for that ROM... http://forum.xda-developers.com/showthread.php?t=614158
Just unzip the rom after you download it, and like before, hook phone up to computer and let it sync, then run the installer. You can also use the ealier AGB roms, too, if they look better to you, or any rom you come across as long as it is a spl3.5 rom.
And I will try to contact michy-prima to see if I can get one of his old clean wm6.5 roms or his stock wm6.1 roms, but I wouldn't count on me being able to get one from him. Personally I think the newer AGB ROMs are alot better and more recent and updated and would recommend using them.
Also, here is a convenient thread I just found that has links to many different builds and useful tools and guides... http://forum.xda-developers.com/showthread.php?t=397518 ... so if you want to try out a couple wm6.1 while you have spl1.2 or even after flashing spl3.5, as a lot of roms are made for both spls. Just make sure you only flash roms made for the spl that you have on your phone.
I hope this helps... if you have any more questions, feel free to pm me and I'll be glad to help. Happy flashing!
Hi Zarathustrax,
Thanks for the extensive instructions. I will be checking it this week so hopefully ill be sending you some greenbacks by Friday!
Thanks again!
Al
bigalk said:
Hi Zarathustrax,
Thanks for the extensive instructions. I will be checking it this week so hopefully ill be sending you some greenbacks by Friday!
Thanks again!
Al
Click to expand...
Click to collapse
Like I said, if you have any more questions or problems, feel free to ask here or pm me.
Sent from my HTC HD2 using XDA App
Also, if you prefer to have a winmo 6.1 ROM over the 6.5 ROM I suggested, there are links to many 6.1 ROMs in that last thread I linked. Here's the link again... http://forum.xda-developers.com/showthread.php?t=397518
MichyPrima's roms are no longer hosted, but I have heard good things about Taxists and Sogarths ROMs. You can easily try a rom and then flash another if you don't like it. Just remember, make sure to flash roms for the spl that you have. If you have SPL3.5 and want a spl1.2 rom, there are links to the tool to change back to spl1.2. The only way to go from spl 1.2 to spl 3.5 is to flash the Athena Project 4 ROM, then after that you can flash any spl3.5 you want. Let me know if you have any other questions or concerns.
Hi Zarathustrax,
just to let you know - i still havent managed to allocate time to this yet.
I havent forgotten about you, and im not pulling a fast one!
thanks again for your time and effort!
Al
Hi Zarathustrax,
In the very first step (unlocker link) Olipro says "follow the steps...."
I cant see the steps he mentions anywhere? This is one of the reasons for my original post
any ideas?
Al
Forget my last question - unlocker has the steps!
Hi Zarathustrax,
tried twice and i keep getting error 202 - "check cables....... cannot connect to phone"
I have:
1) connected and synced via active sync
2) set active sync not to sync any items except for files
any ideas?
thanks
Ive tried everything i can. ALL windows updates installed (along with .net 2.0)
AV disabled
Athenaunlocker added to firewall exceptions - im on a work network so firewall is controlled through group policy - so i cant completely disable. do you think this might be the problem?
bigalk said:
Ive tried everything i can. ALL windows updates installed (along with .net 2.0)
AV disabled
Athenaunlocker added to firewall exceptions - im on a work network so firewall is controlled through group policy - so i cant completely disable. do you think this might be the problem?
Click to expand...
Click to collapse
Hmmm... might be. I'll look into this and see if I can figure anything out.
Oh, by the way, sorry I missed your messages until now. I don't check these forums daily, so if you need to contact me quicker, send a private message to me.
bigalk said:
Hi Zarathustrax,
tried twice and i keep getting error 202 - "check cables....... cannot connect to phone"
I have:
1) connected and synced via active sync
2) set active sync not to sync any items except for files
any ideas?
thanks
Click to expand...
Click to collapse
I've been reading through the forums trying to find an answer... at what point does it show this error? Is it right away? Does the x7501 change screen at all or do anything? I think I remember having problems like this when I unlocked it years ago... but can't remember exactly what I did. Does the x7501 go to it's tricolored bootloader screen at all? It maybe is having problems installing usb drivers while it's in bootloader mode if it changes into bootloader mode when you get that error. Let me know asap so we can get this solved. Also, have you tried using another cable at all?
Putting phone in usb Mode
Try installing Enablerapi.cab before using the olipro unlocker.
Are you still on this
When you run the unlocker there are 3 steps - these are three separate buttons that appear on the flasher each time.
Can you indicate at which step you get this error? Go to this link
http://forum.xda-developers.com/showthread.php?t=378216
...IT IS IN GERMAN...but it gives very nice pics of the process...using google translate you can get some idea. BUT if you can indicate which step you were able to complete.....we can help better !
Also, what windows operating system?
bigalk said:
Ive tried everything i can. ALL windows updates installed (along with .net 2.0)
AV disabled
Athenaunlocker added to firewall exceptions - im on a work network so firewall is controlled through group policy - so i cant completely disable. do you think this might be the problem?
Click to expand...
Click to collapse
chappatti said:
When you run the unlocker there are 3 steps - these are three separate buttons that appear on the flasher each time.
Can you indicate at which step you get this error? Go to this link
http://forum.xda-developers.com/showthread.php?t=378216
...IT IS IN GERMAN...but it gives very nice pics of the process...using google translate you can get some idea. BUT if you can indicate which step you were able to complete.....we can help better !
Also, what windows operating system?
Click to expand...
Click to collapse
I'm kinda thinking he gave up or something.... I've pm'ed him and have been trying to get more info on his problem for a couple weeks. I think he was having the problem on the first step... and the enablerapi will probably solve his problem.
But doing all this reading and trying to solve this problem has got me to pull out my old athena and start playing with it again... it's been a couple years since I've used it... I'm on the HD2 now, dualbooting WP7 and android.... but I've gotten an interest in getting my athena set-up and working again. The athena was way ahead of it's time.... if we could get devs interested in it again and get a good android build ported over, it would make an awesome tablet/phone. I think I'm gonna try to play around with getting android booting on it, but my knowledge of linux and low-level kernel work is limited to none. The best I can do is try to put together a build with what kernels/tools are already out and working on the athena, which isn't much. I think they had it booting and got touch screen working, but not much past that.
Hi zarathustrax,
no i havent given up . was checking in regularly to see if i had any response from you but never even looked at the pms. sorry.
i have a few hours to crack into this now so ive set up on a new machine (different av and firewall) and im going to have a go.
will report back - thanks for all the additional info my man!
al
ok - so i unlocked successfully but i think i may have fcked up. when i read olipros unlocker thread its says that only step 1 is necessary, ("but if you do step 2 you must also do step 3")
as i was trying to get to spl 3.5 i presumed that i didnt need to do step 2 or 3. this might have been a bad choice.
heres what happened:
ran unlocker step 1, it worked, phone rebooted. i finished there as i wasnt sure if i needed step 2 or 3
loaded bootloader screen to check spl. spl said olipro 1.2. i though cool - rebooted phone and now its a black screen. i can get into the bootloader screen whish says:
ATHE100
IPL-V1.00
ATHE100
SPL-V1.20. Olipro
have been reading up on next steps, or how to get rid of blackscreen but no conclusive answer.
its friday so im off home - battle lost but the war aint over!
Well. I'm not an expert (my Ameo was unlocked as I bought it) but if I understand, the black screen is because the ROM on your device dont match the new SPL you have. Try to flash a new ROM (SPL 1.2, right?) should help.
bigalk said:
ok - so i unlocked successfully but i think i may have fcked up. when i read olipros unlocker thread its says that only step 1 is necessary, ("but if you do step 2 you must also do step 3")
as i was trying to get to spl 3.5 i presumed that i didnt need to do step 2 or 3. this might have been a bad choice.
heres what happened:
ran unlocker step 1, it worked, phone rebooted. i finished there as i wasnt sure if i needed step 2 or 3
loaded bootloader screen to check spl. spl said olipro 1.2. i though cool - rebooted phone and now its a black screen. i can get into the bootloader screen whish says:
ATHE100
IPL-V1.00
ATHE100
SPL-V1.20. Olipro
have been reading up on next steps, or how to get rid of blackscreen but no conclusive answer.
its friday so im off home - battle lost but the war aint over!
Click to expand...
Click to collapse
Just replied to your pm before checking this thread, so I see that you can still get to SPL bootloader screen. So, what you should be able to do now is get your phone to bootloader screen and hook it up to pc like that. Then let any drivers that are installing finish, and where it says "serial" at the bottom should change to "USB".
At this point, you can now run a custom rom installer and flash a new rom. Since you want to change to SPL3.5, you should install the Athena Project 4 ROM.
Or if you want to leave it at this SPL for a while and test out a couple WM6.1 ROMS that use this SPL, just flash one of these. Here's a good thread that lists almost every ROM available with links and says what SPL they're for... http://forum.xda-developers.com/showthread.php?t=397518
I'll do a little more research also about the screen not coming on to make sure it's not some other problem, but it probably is just the current rom isn't compatible with the new SPL.
I'm sending this post to your pm too.
Also, make sure you have the SD card and sim card removed when doing flashing. And check what radio you have on your phone... you must have atleast radio 1.50 or higher to use Athena Project 4 or most WM6.1 or WM6.5 ROMS.