first i was trying to upgrade system from O2
something goes wrong and ERROR showed
and i could only my xda in bootloader on
then i was trying to upgrade rom bootloader by mitty
i`ve done this steps :
you will lose all data on your device, and your sd-card, so make a backup first*
make sure there is no sd-card in your device.
boot your device into bootloader mode
by holding down the big action/navigator button together with the power button, and hard-resetting with the pen at the same time
now the display should say 'serial' and the bootloader version.
insert a blank sd-card
put your device in it's cradle
start mtty.exe
select 'usb' as the port in the mtty program.
type the followint command into the mtty window
d2s 60000000 00300000
this will write your radio rom to the sd-card
the last step takes very long and my pc hang up
so i treied to do the same once again but mtty showed me "usb port could not open"
and i dont know what to do know???
plz help me
sory my english isn`t good enough
regards
have you tried just putting the pda in the cradle without using mtty?
if it change status to usb serial you can run the flashtool again
Rudegar said:
have you tried just putting the pda in the cradle without using mtty?
if it change status to usb serial you can run the flashtool again
Click to expand...
Click to collapse
i have same problem...
Yes my xda-II change status from SERIAL to USB.
but in PC my xda-II detected as UNKNOWN DEVICE,
so i can't run FLASHTOOL.
i just hope if flashing to be run from sd-card
mine did that once so i rebooted and or changed usb port
Rudegar said:
mine did that once so i rebooted and or changed usb port
Click to expand...
Click to collapse
I did it, and tried to about 3 PC's winXP SP2,
and still detected as Unknown Device, i think its connector problem or hardware error
Related
It is the first time I flashing rom.
when I make my device into bootloader mode(tri-color screen)
the device will become no response and my pc cannot recognizes the device
but when I push the reset hole
the device can reboot and no problem
how to solve it?
I cannot do any unlock or flash procedure!
please help!
My device info.
Softbank X01HT(flashed to HK dopod rom before purchase)
IPL: 1.01
SPL:1.04
Rom version: 1.23.708.4
Rom date: 07/24/06
radio: 1.13.00.00
protool: 32.49.7018.00W
I have installed .NET Framework 2.0
go to activesync, > file > connection settings > and uncheck "allow usb connections" put your phone into bootloader and plug it into your pc... once your done flashing then go back and re-check "allow usb connections"
shogunmark said:
go to activesync, > file > connection settings > and uncheck "allow usb connections" put your phone into bootloader and plug it into your pc... once your done flashing then go back and re-check "allow usb connections"
Click to expand...
Click to collapse
thx for your reply
but the problem is
my pc cannot connect my device during boot mode
my pc said that new hardware found but it cannot be used normally...
is there need any driver?
Penguina said:
thx for your reply
but the problem is
my pc cannot connect my device during boot mode
my pc said that new hardware found but it cannot be used normally...
is there need any driver?
Click to expand...
Click to collapse
when you enter bootloader mode, does it first display Serial then, when you plug in the USB, does it display USB
Olipro said:
when you enter bootloader mode, does it first display Serial then, when you plug in the USB, does it display USB
Click to expand...
Click to collapse
thx for reply
it displays serial
but when I plug in USB cable
nothing change
PS. I have untick 'allow USB connection' in activesync before
Penguina said:
thx for reply
it displays serial
but when I plug in USB cable
nothing change
PS. I have untick 'allow USB connection' in activesync before
Click to expand...
Click to collapse
your bootloader is corrupt, flash Hard-SPL... you're lucky the damn thing boots.
Olipro said:
your bootloader is corrupt, flash Hard-SPL... you're lucky the damn thing boots.
Click to expand...
Click to collapse
o...but when I flash Hard SPL v6, when it turn to tri-color screen
it shows
HERM200
IPL-SSPL by Des
HERM200
SPL-1.09.ds
then the device become no response
later my pc show error 260, miss connection
....
thx all!
I found the reason...
becoz I use activesync 4.1....
when I upgrade to 4.5
I can flash hard spl
I'm sorry for the typical question and thread!I did everything but without result,
for this reason i've decided to make a post
so as i said on title i'm stuck on boot screen,to let you understand
the screen with 4 colors,red,green,blue,white.Now here the point,it seems that i can't resume my phone
from that screen!I've tried as is written here "format a microSD card with FAT32
extract the .NBH file from the rom image you like
rename the .NBH to HERMIMG.NBH and copy it to your microSD card
put microSD card in phone and start it in bootloader (hold Ok button on left side and POWER button at same time and stick with stylus in RESET on bottom)
confirm flashing on screen" but it was useless,nothing happend,when i push the left button ok
and at the same time power and soft reset,the screen change color become gray and appear a write "Loading...."and some numbers above 00068002
to return invain at the beginning screen.I don't know what i wrong and if is there another way to resume it,obviously my activesync don't work.
Here others informations if it can be useful for someone about my boot screen
Red stripe there's written: HERM200 I PL-1.01
HERM200 SPL-1.11
White stripe: Serial
does anyone had my same problem???
Please help me i really need my phone because my work
Thanks a lot
Try flashing from the computer - just start with the phone in Bootloader mode, select force using SSPL and flash whatever ROM you like. Give it a try.
Thanks for the answer!But i've already tried that way without success,maybe bcause there's not connection with the activesync,could be possible?In fact when i try appear an error wich says
ERROR [260] : UPDATE ERROR
THE UPDATE Utility cannot connect to your PDA Phone.Please check that your USB cradle/cable is connected properly between the PC and your PDA Phone.
Check the following:
1.The PDA Phone is connected to the USB cradle/cable.
2.The USB cradle/cable is connected to the PC.
Now how can i fix this problem????
Thanks for ur collaboration!!!
Pleaaaaaaaaaaase HEEEEEEEEEEEEELLLLLLLLLLLLLLLLPPPPPPPPPPPPPPPPPPP
I have exactly the same problem !!!
Damn!We gotta find a solution!Hey if you can fix our problem please let me know!And naturally the same for me.Let's keep in touch!
White stripe: Serial
Click to expand...
Click to collapse
This should switch to USB once you plug it in...
Give us a little more info now please:
* what file are you trying to flash
* what RUU are you using
* have you tried connecting with mtty (if you get in, try task 28)
* have you trried hard reset
Just to be clear on my previous post...
1. Put phone in BL mode
2. NOW plug phone into computer (that order is important)
*Phone should now say USB*
3. Launch CustomRUU (should not be a retail RUU)
4. Flash
Dear todd_jg,
first of all thanks to be interesting about my problem,
second yes my phone switch to serial in usb mode,
-regarding the RUU i don't have any idea about it!
-Can u post the right RUU that i should use please?
-Never tryed mtty
-Yes i've tried with hard reset but without result,it send me back to the boot screen
-I did exactly as you said but it was invain!
Use the RUU file from THIS THREAD
Get the nbh file
Drop it into a folder with the RUU
Launch the RUU
Whichever nbh is ok???
tetsuokaneda said:
Whichever nbh is ok???
Click to expand...
Click to collapse
Yes, but if you continue to have problems, you may wish to try a different one or at least post a link where you found it...
I got it!I'm trying right now!I'll let u know immediately!Thanx
Fu.. nothing to do....
here what it said
ERROR [260] : UPDATE ERROR
THE UPDATE Utility cannot connect to your PDA Phone.Please check that your USB cradle/cable is connected properly between the PC and your PDA Phone.
I think that the problem is the connection between the Cpu and the Pda.
tetsuokaneda said:
Fu.. nothing to do....
here what it said
ERROR [260] : UPDATE ERROR
THE UPDATE Utility cannot connect to your PDA Phone.Please check that your USB cradle/cable is connected properly between the PC and your PDA Phone.
I think that the problem is the connection between the Cpu and the Pda.
Click to expand...
Click to collapse
Alright - lets try a task 28 with mtty
You will need to find mtty first (should be a link in the wiki or use search).
The tricky part is getting mtty to see the USB connection... I get it by doing the following
1. With the phone in BL mode and mtty closed, plug it in to the USB
2. Using ActiveSync, manuallyt tell it to check for connected devices (this will get it to start polling the ports)
3. While ActiveSync is still polling the ports, open mtty
4. Where it says connect using... or port... or something like that, you should find USB001 or something like that - something with USB in the name. If you don't see it - try steps 1-3 a few times.
Once you have seen the port, you can connect to the phone. The wiki has some instructions for getting to the USB prompt in mtty. Once you are there you want to issue the task 28. See if that helps.
Here is the link to the wiki - a link to mtty is there and some directions. Good luck.
Ok here what i obtained with mtty
Cmd>task 28
Storage format start
Write Nand Success
dwBlockToWrite = 14
Can't find OS in flash!!!
Storage format success
and now?
tetsuokaneda said:
Ok here what i obtained with mtty
Cmd>task 28
Storage format start
Write Nand Success
dwBlockToWrite = 14
Can't find OS in flash!!!
Storage format success
and now?
Click to expand...
Click to collapse
Well... let's see...
SD Card - No
PC - different BLs and RUUs - No
mtty - No
Manual BL mode - No
Almost stumped here... last resort: KITL + PLatform Builder
http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
OR...
Flash an OS.nb file with mtty (READ THESE DIRECTIONS CAREFULLY)
Daaaamn i think will be a long night
I hope if is gonna work
Thanks todd_jg
i'll keep u posted
Apologies but have scoured all the threads and cannot seem to get to a straight answer!
Have a tocuh-dual which I attempted to update to the latest ROM from HTC and now I have the "tri-colour screen of death!) and can get no further,
The screen shows in thered band - RUUNBH | NIKI100 | SPL-1.16.0000 | CPLD-4. The white band shows "serial" and when I connect the USB lead it shows "USB".
But the PC does not recognise it at all and when I try to load a ROM or run MTTY nothing is found. How can I run a program on the touch if the PC will noit see it through the USB connection?
Any ideas?
Does your PC have active Sync installed? I had a similar problem when I installed a broken rom that would not boot up. I did a device reset using the stylus in the whole next to the USB, while holding the camera and power button to boot into the tri color screen. Once hear i plugged in my USB cable and ran a ROM install.
I hope this helps.
uncheck allow usb-connection in Active Sync
run mtty connect by USB
type "boot" without quotes.
same problem
i have got the same problem and can't get out of the tri-colour.
I try to connect with mtty and it says usb port cannot open. my pc can recognise it and in da phone it shows usb though, i don't really know why its not taking. if i type "boot" in mtty what will happen? cos when i click on com3 its opening but when i write "boot" nothing happening even with boot. any ideas guys? how to solve the problem????
Regards
u have to unckeck allow usb connection in active sync! then u can connect with mtty
Just one point - I am using Vista which does not use Activesync but Sync Centre and that does not give you the option to disable as far as I can see?
use xp
bodonline said:
Just one point - I am using Vista which does not use Activesync but Sync Centre and that does not give you the option to disable as far as I can see?
Click to expand...
Click to collapse
Use xp mate, cos vista has got some problems. normally for unlocking and upgrading i use xp. blow up the vista .
Regards
I will crank one up and let you know how it goes!
kill the task in the Task Manager... then u can connect with mtty
Tried killing the process but MTTY still says "USB port cannot open" - no idea what else to do?
If any Program use the USB Port ... no other Program can use the USB at the same time!
Well I was trying to upgrade mt niki to 6.1 but apparently I must have missed a step or did something I shouldt have and now I am stuck with the color bar screen. Can anything be done? I am running Vista.
tri-colour = Bootloader
The tri colour screen is the boot loader screen, when you updated, did the progress bar go allll the way to 100%?
If so, its in bootloader, try to flash another rom from you computer,
Also run through what you done to update - What rom also. Did you hard-spl, Uspl or anything like that?
It stopped at 15%. These are the directions I was following:
Originally Posted by Judge584
Follow these steps:
1. download the attached files (flash-uspl-niki.zip & sspl-1.16-nike)
2. REMOVE SIM and SD CARDS !!
3. connect usb cable
4. copy sspl-1.16-nike.exe to your device and run it (usb cable must be connected!)
5. after a few seconds "USB" appears on the display
6. unplug and replug the usb cable
8. you can now flash the uspl by running ROMUpdateUtility.exe from flash-uspl-niki
9. Now you can flash the latest rom update to have spl 1.22 and wm6.1.
ouch, Thats the only problem with sspl,
urmm.
How long did it stay at 15%?
As the device isn't CID unlocked you can only flash official roms...
Find an official rom, in the bootloader connect the USB and see if it will flash. It should do!
fingers crossed..
the only rom I can find for singtel in singapore is an updated one so I am trying that now so far so good, I am at 30%. So if this will get me going again can you offer a little advice or explination as to your last post, how do I go about loading a newer 6.1 rom on my device?
Of course, thats what these forums are for. The singapore rom shouldn't hassle you tooo much if you know your way around Windows mob well enough. Let me know how it goes and i'll help you through..
Deejaynate said:
Of course, thats what these forums are for. The singapore rom shouldn't hassle you tooo much if you know your way around Windows mob well enough. Let me know how it goes and i'll help you through..
Click to expand...
Click to collapse
well i was able to fix it by using the singtel rom. I want to use the Niki SuperCID unlocker but I have to install the " HardSPL 1.15 MFG " first - can you walk mw through this so I dont brick my touch again. do you have messenger?
yeah Windows live messenger, add me [email protected]
sorry to hijack your thread, but I encountered exactly the same thing. The screen is now stuck with 3 colour bands. I tried to flash it with an official rom, but the computer is not connecting with the phone, active sync does not recognise the device, any help!?
this is what I did:
1. download the attached files
2. REMOVE SIM and SD CARDS !!
3. connect usb cable
4. copy sspl-1.16-nike.exe to your device and run it (usb cable must be connected!)
5. after a few seconds "USB" appears on the display
6. unplug and replug the usb cable
8. running ROMUpdateUtility.exe from flash-uspl-niki
Sorry for the non prompt reply
I have been at work alot lately,
sorry for a non prompt reply.
Active sync wont connect to your phone, as its in bootloader mode.
At the tri-colour screen, does you computer beep when you connect it, or try to install drivers?
thanks for replying!
no beep from the computer, when connecting the usb to the phone, the phone changes from "serial" to "usb".
I tried reflashing with ROMUpdateUtility.exe from flash-uspl-niki, it will work, but says fail and will go into recovery mode. It will then complete the "recovery" action and go back to flashing new rom which won't work.......
The same ocurred with me!! Help me!
In the middle of an unlocking process, somehow(in the flashing radio process,i got 100%, and then a message saying: an writing error ocurred). So my htc dual got with the image NIKI200 (and four colour - red,green,blue and white..). Now i tried hard reset and after i presse send to initialize, the phone goes to that bloody image....i cant do nothing....what should i do? help me please....regards
luismatos123 said:
In the middle of an unlocking process, somehow(in the flashing radio process,i got 100%, and then a message saying: an writing error ocurred). So my htc dual got with the image NIKI200 (and four colour - red,green,blue and white..). Now i tried hard reset and after i presse send to initialize, the phone goes to that bloody image....i cant do nothing....what should i do? help me please....regards
Click to expand...
Click to collapse
You need to flash an original ROM from your service provider (phone company).
Hi! I tryed te fash my niki 200 with original rom! The flash is stopes to 42% and now i have boot mode with this message "Upgrade ROM code error! Please try again". I can not conect again to usb because i received message :"usb device not recognized". Mtty can not conect because i received the same message! There is another metod de make this device?
Have you flashed HardSPL?
Put your device into bootloader (hold b oth Camera and Power button while performing a Softreset via Stylus) and now you can theoretically flash your Provider ROM!
After that your device will work again!
I have not flashed hardspl! If i put the Niki in boot mode, show only "serial" on the screen with usb cable pluged and PC says "usb device not recocnized"!
Flashing in bootloader mode doesn't requires an ActiveSync connection so ignore it and start the ROM Upgrade! It's working, believe me! I've flashed my Niki with this method hundred of times!
I tryed to flash my niki in bootmood, but not working "error 260:conection"! My computer not recocnized my device (with or without activesync)!!!In bootmode on screen show "serial" and when i pluged the cable nothing happend (must see on screen:USB)! This is my problem!!! The computer does not alocate to my device a com port(USB). The same problem with MTTY (no USB poet detected). You understand me?
Maybe your USB drivers screwed up.
Trie with an other PC, this helped me one time.
I tryed on other computer with Xp and other with Vista! The same problem! Not recocnized!!!!!!!!!!!!!!!!!
bugytech said:
I tryed on other computer with Xp and other with Vista! The same problem! Not recocnized!!!!!!!!!!!!!!!!!
Click to expand...
Click to collapse
I've got the same issue. Did you resolve this? I would like to find a solution