Hi! I tryed te fash my niki 200 with original rom! The flash is stopes to 42% and now i have boot mode with this message "Upgrade ROM code error! Please try again". I can not conect again to usb because i received message :"usb device not recognized". Mtty can not conect because i received the same message! There is another metod de make this device?
Have you flashed HardSPL?
Put your device into bootloader (hold b oth Camera and Power button while performing a Softreset via Stylus) and now you can theoretically flash your Provider ROM!
After that your device will work again!
I have not flashed hardspl! If i put the Niki in boot mode, show only "serial" on the screen with usb cable pluged and PC says "usb device not recocnized"!
Flashing in bootloader mode doesn't requires an ActiveSync connection so ignore it and start the ROM Upgrade! It's working, believe me! I've flashed my Niki with this method hundred of times!
I tryed to flash my niki in bootmood, but not working "error 260:conection"! My computer not recocnized my device (with or without activesync)!!!In bootmode on screen show "serial" and when i pluged the cable nothing happend (must see on screen:USB)! This is my problem!!! The computer does not alocate to my device a com port(USB). The same problem with MTTY (no USB poet detected). You understand me?
Maybe your USB drivers screwed up.
Trie with an other PC, this helped me one time.
I tryed on other computer with Xp and other with Vista! The same problem! Not recocnized!!!!!!!!!!!!!!!!!
bugytech said:
I tryed on other computer with Xp and other with Vista! The same problem! Not recocnized!!!!!!!!!!!!!!!!!
Click to expand...
Click to collapse
I've got the same issue. Did you resolve this? I would like to find a solution
Related
i tried to install the latest At&t ROM and i got an error asked me to try and recover it but when i try to recover it it still give me an error message and now my phone is stuck on the bootloader screen it says IPL-1.00 SPL-1.40.Olipro can someone please help me get this out of bootloader mode...i tried reseting it or tried other ROM's but nothing will work....TIA
i can't even get my pc to recongnize that my 8525 is connected to the USB port....
EDIT: I got my PC to see my 8525 by unchecking the USB connections in ActiveSync....
I think this is a crosspost from the HardSPL receovery thread, so I will just answer it here.
Manually put phone in bootloader mode.
Plug into USB
Run RUU to start ROM install
Manaually select your SPL version
Ignore warning in red letters on next screen
Flash away.
(Do not mix up the first two steps - put in bootloader, THEN plug into USB)
If this does not not work, use SD Card flashing method.
help pls my atom always in boot loader mode, i have try upgrade to wm6 jiggs rom or the official o2 rom, but always stuck in bootloader mode can anyone help me pls
sorry my bad english
Pls explain what you did and what is the current status of your device clearly..
I think you should be able to reflash. Does it say "connect a USB cable" on screen, or is there just a jumble of text like a DOS prompt?
Try connecting via USB and run the update executable again. That usually works.
If that isn't your problem, I'm currently not good enough to solve it for you.
Had the same problem flashing WM6.03 before. Changed the USB cable and reflashed. It worked. Sometimes the problem is in the connection no the device or PC.
yes the device say "connect a USB cable" but i already flash 4x time = 3 x time with the official o2 rom 1 x with wm6 aku7.0 from jiggs, but it's doesn't work my atom stuck in "connect a usb cable", pls help
yes i already change n reflashed but stuck in screen "connect a USB cable" n i tried soft reset but once again back in screen "connect a USB cable" any one can help me what rom i should reflash for bring back my atom,
Methinks your flashes went wrong because it didn't flash the extROM successfully. This only happens if you're using the hacked Atom Exec ROM on the Atom. <_<
When I ended up like this once, all I did was keep on trying and trying again until the entire procedure goes right through (it will do so eventually). That's the only answer I know.
I can't help any further.
yuberthegreat said:
yes i already change n reflashed but stuck in screen "connect a USB cable" n i tried soft reset but once again back in screen "connect a USB cable" any one can help me what rom i should reflash for bring back my atom,
Click to expand...
Click to collapse
read the Atom Wiki under upgrading problems.
Hi ;
i managed to enter the three color bootloader screen by pressing the camera button while restarting the device, then i ran the RUU_Prophet_220734_2207114_024721_NVID but it constantly gives me the error 260 (cannot connect to device).
now it dosen't conect to PC .i use Xp.
Thanks
Ya.. i also face the same problem..Can anyone help..only success flash just once
Within activesync disable connect through USB (Options->connection settings->Connect through USB), and try again.
first i was trying to upgrade system from O2
something goes wrong and ERROR showed
and i could only my xda in bootloader on
then i was trying to upgrade rom bootloader by mitty
i`ve done this steps :
you will lose all data on your device, and your sd-card, so make a backup first*
make sure there is no sd-card in your device.
boot your device into bootloader mode
by holding down the big action/navigator button together with the power button, and hard-resetting with the pen at the same time
now the display should say 'serial' and the bootloader version.
insert a blank sd-card
put your device in it's cradle
start mtty.exe
select 'usb' as the port in the mtty program.
type the followint command into the mtty window
d2s 60000000 00300000
this will write your radio rom to the sd-card
the last step takes very long and my pc hang up
so i treied to do the same once again but mtty showed me "usb port could not open"
and i dont know what to do know???
plz help me
sory my english isn`t good enough
regards
have you tried just putting the pda in the cradle without using mtty?
if it change status to usb serial you can run the flashtool again
Rudegar said:
have you tried just putting the pda in the cradle without using mtty?
if it change status to usb serial you can run the flashtool again
Click to expand...
Click to collapse
i have same problem...
Yes my xda-II change status from SERIAL to USB.
but in PC my xda-II detected as UNKNOWN DEVICE,
so i can't run FLASHTOOL.
i just hope if flashing to be run from sd-card
mine did that once so i rebooted and or changed usb port
Rudegar said:
mine did that once so i rebooted and or changed usb port
Click to expand...
Click to collapse
I did it, and tried to about 3 PC's winXP SP2,
and still detected as Unknown Device, i think its connector problem or hardware error
HI!
I from russia)
HTC don't power on, in the boot mode activesync don't conect to him(((
helpme!
flash a new rom with bootloader screen without activesync
Thanks, but how to me to make it?
Prompt me please!
I shall be very grateful!
download this rom: http://rapidshare.de/files/38259115/RUU_Oxygen_1.5.401.2_R3_4.1.13.28_02.67.90_HTC_EUR_Test.exe.html
Then put your smartphone in bootloader
press (volume down button + photo button ) and then power button for 2 second
when appear a screen color red - green - blue connect usb and install rom downloaded from pc
excuse me for my english
Gives out (260 error)...
Active Sync thus was switched - off, mtty writes that can not open usb port (((
Help!
dont install with Mytt.
you must only enter in bootloader
connect usb to phone and to pc
(activesync NO active)
and install new ROM from exe downloaded.
try
Tried, it deduces error 260, and mytt I tried to connect already then, but unsuccessfully....
RESET pc and phone.
and try
you enter to boot loader?
reset made) some times, boot loader is included
But connection does not occur.
uuuhhmmm!!!
change USB PC port!!
i try with my oxy and work
I made all described above on 4 different PC result everywhere identical...
change USB PC port!!
i try with my oxy and work
Explain!
I have ugual problem, but i have flash in bootloader screen, without mytt, only connecting usb port and double clic to exe rom downloaded.