HI!
I from russia)
HTC don't power on, in the boot mode activesync don't conect to him(((
helpme!
flash a new rom with bootloader screen without activesync
Thanks, but how to me to make it?
Prompt me please!
I shall be very grateful!
download this rom: http://rapidshare.de/files/38259115/RUU_Oxygen_1.5.401.2_R3_4.1.13.28_02.67.90_HTC_EUR_Test.exe.html
Then put your smartphone in bootloader
press (volume down button + photo button ) and then power button for 2 second
when appear a screen color red - green - blue connect usb and install rom downloaded from pc
excuse me for my english
Gives out (260 error)...
Active Sync thus was switched - off, mtty writes that can not open usb port (((
Help!
dont install with Mytt.
you must only enter in bootloader
connect usb to phone and to pc
(activesync NO active)
and install new ROM from exe downloaded.
try
Tried, it deduces error 260, and mytt I tried to connect already then, but unsuccessfully....
RESET pc and phone.
and try
you enter to boot loader?
reset made) some times, boot loader is included
But connection does not occur.
uuuhhmmm!!!
change USB PC port!!
i try with my oxy and work
I made all described above on 4 different PC result everywhere identical...
change USB PC port!!
i try with my oxy and work
Explain!
I have ugual problem, but i have flash in bootloader screen, without mytt, only connecting usb port and double clic to exe rom downloaded.
Related
Hello,
after flashing many, many roms I am not able to flash any more roms....
The problem is: my bootloader stays in SERIAL mode and won't go in USB mode.
I had this problem somethimes before, but after some resetting(PPC and PC), swithing USB cable into antoher USB port after a while he did go into USB mode. But this time nothing works...I tried it manually(power button + ok button + soft reset) and with active sync...but nothing works for me.
I have tried searching the forum, found some articles mentioned it, but no solution.
Anybody else had this problem? My bet: it's a PC problem.....but don't know the solution
Info:
Herm300
IPL-1.04
SPL-2.10Olipro
Current rom: Pandora build 1825
<edit>
PC: Windows XP
tried 2 different USB cables
tried all USB ports
</edit>
Problem Solved !
Solution: reinstall active sync.....
1. Uninstall Activesync 4.5 from Control Panel | Add/Remove Programs
2. Reboot your PC
3. Check to make sure \Program Files\Microsoft Activesync no longer exists - delete it if it's still there.
4. Make sure your phone is NOT connected to your PC and re-install Activesync 4.5
5. Reboot your PC (sorry if this is a bit tedious )
6. Connect your phone directly to a USB port on your PC, NOT VIA A USB HUB!!!
7. Activesync should now detect your phone and start the "Create new partnetship" wizard.
Fine, when problems are solving itselfs, flashing time again, and again and...
Hi! I tryed te fash my niki 200 with original rom! The flash is stopes to 42% and now i have boot mode with this message "Upgrade ROM code error! Please try again". I can not conect again to usb because i received message :"usb device not recognized". Mtty can not conect because i received the same message! There is another metod de make this device?
Have you flashed HardSPL?
Put your device into bootloader (hold b oth Camera and Power button while performing a Softreset via Stylus) and now you can theoretically flash your Provider ROM!
After that your device will work again!
I have not flashed hardspl! If i put the Niki in boot mode, show only "serial" on the screen with usb cable pluged and PC says "usb device not recocnized"!
Flashing in bootloader mode doesn't requires an ActiveSync connection so ignore it and start the ROM Upgrade! It's working, believe me! I've flashed my Niki with this method hundred of times!
I tryed to flash my niki in bootmood, but not working "error 260:conection"! My computer not recocnized my device (with or without activesync)!!!In bootmode on screen show "serial" and when i pluged the cable nothing happend (must see on screen:USB)! This is my problem!!! The computer does not alocate to my device a com port(USB). The same problem with MTTY (no USB poet detected). You understand me?
Maybe your USB drivers screwed up.
Trie with an other PC, this helped me one time.
I tryed on other computer with Xp and other with Vista! The same problem! Not recocnized!!!!!!!!!!!!!!!!!
bugytech said:
I tryed on other computer with Xp and other with Vista! The same problem! Not recocnized!!!!!!!!!!!!!!!!!
Click to expand...
Click to collapse
I've got the same issue. Did you resolve this? I would like to find a solution
Hi everyone.
So I have a Motorola Droid RAZR XT910 its on 4.0.4 OTA with no root.
The issue I have is that I connect the phone to my PC via USB cable and it does not pick it up.
A few things you must know is:
•I have windows 7 32-bit and
•I am using the cable that comes with my phone
What happens when I plug my phone is the computer says installing drivers for unknown device and then it claims to have successfully installing them for "unknown device". My phone does give me option to chose what type of connection I want but it does charge.
Things I have tried:
•A different cable
•A different PC
• Re-installing drivers
• Re-installing Motocast
•Trying with USB Debugging enabled and disabled
•Different USB ports
•Factory reset
•Different USB ports
•Tried installing PIM Sync form Google Play Store
So yeah that's my problem any help will be helpful...
Try the drivers here:
http://www.motorola.com/consumers/v...59431210VgnVCM1000008406b00aRCRD&pubid=987654
When you try another cable, make sure that works with another device, and not just for charging.
The below instructions will help you troubleshoot if there is a problem with the usb connector on your phone.
1.Power off and disconnect usb cable.
2.Press and hold vol up and down, then hold the power button.
3.You should come to a boot mode selection menu.
4.Press vol down twice to highlight AP fastboot, press vol up once to select.
5.You should see AP fastboot flash mode (s), with last 2 lines saying "Connect USB, Data Cable"
6.Connect your USB cable to your PC and phone, and see if it says USB connected.
7. If nothing happens then it's probably a hardware problem, get it repaired.
Nikorasu said:
Try the drivers here:
http://www.motorola.com/consumers/v...59431210VgnVCM1000008406b00aRCRD&pubid=987654
When you try another cable, make sure that works with another device, and not just for charging.
The below instructions will help you troubleshoot if there is a problem with the usb connector on your phone.
1.Power off and disconnect usb cable.
2.Press and hold vol up and down, then hold the power button.
3.You should come to a boot mode selection menu.
4.Press vol down twice to highlight AP fastboot, press vol up once to select.
5.You should see AP fastboot flash mode (s), with last 2 lines saying "Connect USB, Data Cable"
6.Connect your USB cable to your PC and phone, and see if it says USB connected.
7. If nothing happens then it's probably a hardware problem, get it repaired.
Click to expand...
Click to collapse
Hi thank you for your help.
So I did this method on my PC and it was unsuccessful but i tried it on my mothers and it worked!
So I will update the drivers on my mothers PC and see If I can successfully connect to her PC and use USB mass storage for the first time since I've had Ice Cream Sandwich!
I will keep you updated
Its definitely software. Ill have to wait till there's a rooting application that doesn't require a connection between a PC and phone. One rooted I can flash a ROM from there on...
On your mother's PC, it worked in AP fastboot right? As in the words "USB connected" appears on your phone.
From there you can flash a rom.
Nikorasu said:
On your mother's PC, it worked in AP fastboot right? As in the words "USB connected" appears on your phone.
From there you can flash a rom.
Click to expand...
Click to collapse
I can flash fastboot files which I dont want to do.. I want to flash custom ROMs which require root.
The ap fastboot worked for me but when i restarted the phone it still wont connect with mass storage. i do not own a motorola usb cable mine is an LG and i dont really have money to buy one. bought the phone on ebay and it did not ship with one so ive been using this. it only connects as charging.
My Xperia Ray is originally from SFR. Simlock is removed (code from SFR).
I tried to unlock bootloader using control point method - S1Tool said it's OK (I don't know how to check if it is really OK). I flashed new radio (v.77) without problem using flashtool.
Now I'm trying to enter fastboot mode to change kernel and ROM - no success. Nothing happens if I connect the telephone to PC with Vol+ pressed (it just starts charging). Nothing if I start it Vol+ pressed (it just starts normally). The LED is never flashing blue.
I tested another Xperia Ray (from Bouygues Telecom) - the same thing, no fastboot mode.
Any suggestions?
So,did you have the drivers properly installed on your PC?
You can find it while installing Flashtool.
install drivers from folder in flashtool and then :
1. Disconnect phone from USB
2. Turn off phone (make sure you have at least 50% battery) and wait 30 seconds.
3. Hold the 'Volume UP key' WHILE inserting the USB. --> LED turns blue = fastboot mode.
4. Leave the phone turned off
Sure, the driver is installed.
Nothing happens when I try to connect it Vol+ pressed, NOTHING.
The PC does not see the phone, the phone goes to charging, the LED does not flash blue.
:crying:
no os no recovery no pc detection
hi i'm having a similar problem With my xperia ray
where i have done this:
went into recovery mode via pvyparts
formated system formatted cache formatted dalvik caches
then partioned the sd card
then selected reboot recovery
stuck in boot logo
then phone turned off
pc will not detect the phone
installed 4.2 adb drivers pc companion drivers
flashtool will not detect the phone either
thank you for all the help
After a did a firmware update using USB Burning tool, without no troubles, I want to install other firmware because the accelerometer doesn't work, and so the auto-rotate function (it worked on the old firmware), and I can't get into recovery mode, the home + power function does not work anymore.
I want to use USB Burning tool to reflash the tablet, like the last time, but now I have this problem: when I connect the tablet trough USB cable with the power on, windows recognize the mass storage, but when the power is off, which I need for USB Burning tool, it doesn't do anything. It should show in the bottom-right corner that USB device found, but it doesn't.
I tried this:
1. to hold home-button and then to insert USB... nothing, it just shows the battery charging
2. to hold home+power button... nothing... doesn't enter in recovery mode, it's just loading android system.
3. SD card slot was empty when I tried this.
Does anybody had some king of problems? or know what's the problem?
Please, I need to fix this.