Hi ;
i managed to enter the three color bootloader screen by pressing the camera button while restarting the device, then i ran the RUU_Prophet_220734_2207114_024721_NVID but it constantly gives me the error 260 (cannot connect to device).
now it dosen't conect to PC .i use Xp.
Thanks
Ya.. i also face the same problem..Can anyone help..only success flash just once
Within activesync disable connect through USB (Options->connection settings->Connect through USB), and try again.
Related
Hi,
I have been upgrading to my 2.06.00WWE to 1.60a wm2k5 But when i connected and run bootloader mode and trying to run HimaUpgradeUt.exe or himaupgradeut_noID.exe was crashing or bootloader mode writings was dissappear so It says "101 communication error" so I put the HimaClearJumpCode.exe and run HimaUpgradeUt without bootloader mode when my Himalaya was runing it started and it run to just "removing your old rom" ad then it crashed again when I tried to restart my pocketpc It stuck to bootloader mode again and again.
I tried my old rom to upgrade but the same thing happens as bootloader screen writings disappear or crushings occur.I have an Tmobile mda.Thanks nad please help
I also tried to run himaupgradeut_noID.exe and when this bootloader writings disappear I disconnet it and open in bootloader mode to return writings and connect it to cradle again.Everything goes ok but when It comes to deleting and writing stage It gives me some error ocured and does not say which error is because there is blank
i would try using another pc
try using another pc that can be a error in windows
and do you have power aplied tothe xda when update?
I tried on my friends laptop win xp with sp2 and yes i applied the power to the cradle.. but it doesnt seem to work... bootloader mode shuts itself off when i start the HimaUpgradeUt.exe then it (the exe) crushes.
Zool said:
I tried on my friends laptop win xp with sp2 and yes i applied the power to the cradle.. but it doesnt seem to work... bootloader mode shuts itself off when i start the HimaUpgradeUt.exe then it (the exe) crushes.
Click to expand...
Click to collapse
The blank screen is normal. The display will return as soon as you confirm upgrade on PC screen prompt & it starts erasing the PPC ROM.
Have you tried waiting 'long enough' (at least 2 minutes) before the upgrade prompt confirmation displays in your PC?
When you said 'crashes' which one the PC or the PPC? Any message in your PC/Laptop? Have you installed Active Sync Version 4? Have you gone through with the Magneto Upgrade 'sticky' of XdaIIJojo & check for the prerequisites in upgrading?
Pls. check those 1st!
HimaUpgradeUt.exe crashes.Pc or PPC does not crash.I cant try it because of HimaUpgradeUt.exe crashes even ActiveSync 4.0 and says;
AppName: himaupgradeut.exe AppVer: 1.2.0.0 ModName: himaupgradeut.exe
ModVer: 1.2.0.0 Offset: 00010ed9
I have tried 3 different computer but the same HimaUpgradeUt.exe crashes.
I cant go on Magneto Upgrade 'sticky' of XdaIIJojo & because on this thread there is just a big picture.
Sorry to disappoint you Zool but, my setup is O2 Xda II & there could be some difference with your T.Mobile MDA.
Isnt there any other option ?
Hello,
after flashing many, many roms I am not able to flash any more roms....
The problem is: my bootloader stays in SERIAL mode and won't go in USB mode.
I had this problem somethimes before, but after some resetting(PPC and PC), swithing USB cable into antoher USB port after a while he did go into USB mode. But this time nothing works...I tried it manually(power button + ok button + soft reset) and with active sync...but nothing works for me.
I have tried searching the forum, found some articles mentioned it, but no solution.
Anybody else had this problem? My bet: it's a PC problem.....but don't know the solution
Info:
Herm300
IPL-1.04
SPL-2.10Olipro
Current rom: Pandora build 1825
<edit>
PC: Windows XP
tried 2 different USB cables
tried all USB ports
</edit>
Problem Solved !
Solution: reinstall active sync.....
1. Uninstall Activesync 4.5 from Control Panel | Add/Remove Programs
2. Reboot your PC
3. Check to make sure \Program Files\Microsoft Activesync no longer exists - delete it if it's still there.
4. Make sure your phone is NOT connected to your PC and re-install Activesync 4.5
5. Reboot your PC (sorry if this is a bit tedious )
6. Connect your phone directly to a USB port on your PC, NOT VIA A USB HUB!!!
7. Activesync should now detect your phone and start the "Create new partnetship" wizard.
Fine, when problems are solving itselfs, flashing time again, and again and...
HI!
I from russia)
HTC don't power on, in the boot mode activesync don't conect to him(((
helpme!
flash a new rom with bootloader screen without activesync
Thanks, but how to me to make it?
Prompt me please!
I shall be very grateful!
download this rom: http://rapidshare.de/files/38259115/RUU_Oxygen_1.5.401.2_R3_4.1.13.28_02.67.90_HTC_EUR_Test.exe.html
Then put your smartphone in bootloader
press (volume down button + photo button ) and then power button for 2 second
when appear a screen color red - green - blue connect usb and install rom downloaded from pc
excuse me for my english
Gives out (260 error)...
Active Sync thus was switched - off, mtty writes that can not open usb port (((
Help!
dont install with Mytt.
you must only enter in bootloader
connect usb to phone and to pc
(activesync NO active)
and install new ROM from exe downloaded.
try
Tried, it deduces error 260, and mytt I tried to connect already then, but unsuccessfully....
RESET pc and phone.
and try
you enter to boot loader?
reset made) some times, boot loader is included
But connection does not occur.
uuuhhmmm!!!
change USB PC port!!
i try with my oxy and work
I made all described above on 4 different PC result everywhere identical...
change USB PC port!!
i try with my oxy and work
Explain!
I have ugual problem, but i have flash in bootloader screen, without mytt, only connecting usb port and double clic to exe rom downloaded.
Apologies but have scoured all the threads and cannot seem to get to a straight answer!
Have a tocuh-dual which I attempted to update to the latest ROM from HTC and now I have the "tri-colour screen of death!) and can get no further,
The screen shows in thered band - RUUNBH | NIKI100 | SPL-1.16.0000 | CPLD-4. The white band shows "serial" and when I connect the USB lead it shows "USB".
But the PC does not recognise it at all and when I try to load a ROM or run MTTY nothing is found. How can I run a program on the touch if the PC will noit see it through the USB connection?
Any ideas?
Does your PC have active Sync installed? I had a similar problem when I installed a broken rom that would not boot up. I did a device reset using the stylus in the whole next to the USB, while holding the camera and power button to boot into the tri color screen. Once hear i plugged in my USB cable and ran a ROM install.
I hope this helps.
uncheck allow usb-connection in Active Sync
run mtty connect by USB
type "boot" without quotes.
same problem
i have got the same problem and can't get out of the tri-colour.
I try to connect with mtty and it says usb port cannot open. my pc can recognise it and in da phone it shows usb though, i don't really know why its not taking. if i type "boot" in mtty what will happen? cos when i click on com3 its opening but when i write "boot" nothing happening even with boot. any ideas guys? how to solve the problem????
Regards
u have to unckeck allow usb connection in active sync! then u can connect with mtty
Just one point - I am using Vista which does not use Activesync but Sync Centre and that does not give you the option to disable as far as I can see?
use xp
bodonline said:
Just one point - I am using Vista which does not use Activesync but Sync Centre and that does not give you the option to disable as far as I can see?
Click to expand...
Click to collapse
Use xp mate, cos vista has got some problems. normally for unlocking and upgrading i use xp. blow up the vista .
Regards
I will crank one up and let you know how it goes!
kill the task in the Task Manager... then u can connect with mtty
Tried killing the process but MTTY still says "USB port cannot open" - no idea what else to do?
If any Program use the USB Port ... no other Program can use the USB at the same time!
Hi! I tryed te fash my niki 200 with original rom! The flash is stopes to 42% and now i have boot mode with this message "Upgrade ROM code error! Please try again". I can not conect again to usb because i received message :"usb device not recognized". Mtty can not conect because i received the same message! There is another metod de make this device?
Have you flashed HardSPL?
Put your device into bootloader (hold b oth Camera and Power button while performing a Softreset via Stylus) and now you can theoretically flash your Provider ROM!
After that your device will work again!
I have not flashed hardspl! If i put the Niki in boot mode, show only "serial" on the screen with usb cable pluged and PC says "usb device not recocnized"!
Flashing in bootloader mode doesn't requires an ActiveSync connection so ignore it and start the ROM Upgrade! It's working, believe me! I've flashed my Niki with this method hundred of times!
I tryed to flash my niki in bootmood, but not working "error 260:conection"! My computer not recocnized my device (with or without activesync)!!!In bootmode on screen show "serial" and when i pluged the cable nothing happend (must see on screen:USB)! This is my problem!!! The computer does not alocate to my device a com port(USB). The same problem with MTTY (no USB poet detected). You understand me?
Maybe your USB drivers screwed up.
Trie with an other PC, this helped me one time.
I tryed on other computer with Xp and other with Vista! The same problem! Not recocnized!!!!!!!!!!!!!!!!!
bugytech said:
I tryed on other computer with Xp and other with Vista! The same problem! Not recocnized!!!!!!!!!!!!!!!!!
Click to expand...
Click to collapse
I've got the same issue. Did you resolve this? I would like to find a solution