Hi,
I have been upgrading to my 2.06.00WWE to 1.60a wm2k5 But when i connected and run bootloader mode and trying to run HimaUpgradeUt.exe or himaupgradeut_noID.exe was crashing or bootloader mode writings was dissappear so It says "101 communication error" so I put the HimaClearJumpCode.exe and run HimaUpgradeUt without bootloader mode when my Himalaya was runing it started and it run to just "removing your old rom" ad then it crashed again when I tried to restart my pocketpc It stuck to bootloader mode again and again.
I tried my old rom to upgrade but the same thing happens as bootloader screen writings disappear or crushings occur.I have an Tmobile mda.Thanks nad please help
I also tried to run himaupgradeut_noID.exe and when this bootloader writings disappear I disconnet it and open in bootloader mode to return writings and connect it to cradle again.Everything goes ok but when It comes to deleting and writing stage It gives me some error ocured and does not say which error is because there is blank
i would try using another pc
try using another pc that can be a error in windows
and do you have power aplied tothe xda when update?
I tried on my friends laptop win xp with sp2 and yes i applied the power to the cradle.. but it doesnt seem to work... bootloader mode shuts itself off when i start the HimaUpgradeUt.exe then it (the exe) crushes.
Zool said:
I tried on my friends laptop win xp with sp2 and yes i applied the power to the cradle.. but it doesnt seem to work... bootloader mode shuts itself off when i start the HimaUpgradeUt.exe then it (the exe) crushes.
Click to expand...
Click to collapse
The blank screen is normal. The display will return as soon as you confirm upgrade on PC screen prompt & it starts erasing the PPC ROM.
Have you tried waiting 'long enough' (at least 2 minutes) before the upgrade prompt confirmation displays in your PC?
When you said 'crashes' which one the PC or the PPC? Any message in your PC/Laptop? Have you installed Active Sync Version 4? Have you gone through with the Magneto Upgrade 'sticky' of XdaIIJojo & check for the prerequisites in upgrading?
Pls. check those 1st!
HimaUpgradeUt.exe crashes.Pc or PPC does not crash.I cant try it because of HimaUpgradeUt.exe crashes even ActiveSync 4.0 and says;
AppName: himaupgradeut.exe AppVer: 1.2.0.0 ModName: himaupgradeut.exe
ModVer: 1.2.0.0 Offset: 00010ed9
I have tried 3 different computer but the same HimaUpgradeUt.exe crashes.
I cant go on Magneto Upgrade 'sticky' of XdaIIJojo & because on this thread there is just a big picture.
Sorry to disappoint you Zool but, my setup is O2 Xda II & there could be some difference with your T.Mobile MDA.
Isnt there any other option ?
Related
I have an imate ppc i some how wiped out my copy of windows 2003. I have another copy of the rom. but cant seem to get past the checking information on your pocket pc screen, from there it just falls over and wont go any futher than the ERROR 101: connection error, i have the ppc coneected via a usb connection. the pocket PC says USB at the top of the screen and v1.06 at the bottom.
I would appreciate any help.
Cheers
Sam
marsam said:
I have an imate ppc i some how wiped out my copy of windows 2003. I have another copy of the rom. but cant seem to get past the checking information on your pocket pc screen, from there it just falls over and wont go any futher than the ERROR 101: connection error, i have the ppc coneected via a usb connection. the pocket PC says USB at the top of the screen and v1.06 at the bottom.
I would appreciate any help.
Cheers
Sam
Click to expand...
Click to collapse
You are in the bootloader mode. just disable the usb connection, connect the device (in bootloader mode) and execute the upgrade utility. You are more likely to succeed when you upgrade in bootloader mode.
Hi ;
i managed to enter the three color bootloader screen by pressing the camera button while restarting the device, then i ran the RUU_Prophet_220734_2207114_024721_NVID but it constantly gives me the error 260 (cannot connect to device).
now it dosen't conect to PC .i use Xp.
Thanks
Ya.. i also face the same problem..Can anyone help..only success flash just once
Within activesync disable connect through USB (Options->connection settings->Connect through USB), and try again.
Well I was trying to upgrade mt niki to 6.1 but apparently I must have missed a step or did something I shouldt have and now I am stuck with the color bar screen. Can anything be done? I am running Vista.
tri-colour = Bootloader
The tri colour screen is the boot loader screen, when you updated, did the progress bar go allll the way to 100%?
If so, its in bootloader, try to flash another rom from you computer,
Also run through what you done to update - What rom also. Did you hard-spl, Uspl or anything like that?
It stopped at 15%. These are the directions I was following:
Originally Posted by Judge584
Follow these steps:
1. download the attached files (flash-uspl-niki.zip & sspl-1.16-nike)
2. REMOVE SIM and SD CARDS !!
3. connect usb cable
4. copy sspl-1.16-nike.exe to your device and run it (usb cable must be connected!)
5. after a few seconds "USB" appears on the display
6. unplug and replug the usb cable
8. you can now flash the uspl by running ROMUpdateUtility.exe from flash-uspl-niki
9. Now you can flash the latest rom update to have spl 1.22 and wm6.1.
ouch, Thats the only problem with sspl,
urmm.
How long did it stay at 15%?
As the device isn't CID unlocked you can only flash official roms...
Find an official rom, in the bootloader connect the USB and see if it will flash. It should do!
fingers crossed..
the only rom I can find for singtel in singapore is an updated one so I am trying that now so far so good, I am at 30%. So if this will get me going again can you offer a little advice or explination as to your last post, how do I go about loading a newer 6.1 rom on my device?
Of course, thats what these forums are for. The singapore rom shouldn't hassle you tooo much if you know your way around Windows mob well enough. Let me know how it goes and i'll help you through..
Deejaynate said:
Of course, thats what these forums are for. The singapore rom shouldn't hassle you tooo much if you know your way around Windows mob well enough. Let me know how it goes and i'll help you through..
Click to expand...
Click to collapse
well i was able to fix it by using the singtel rom. I want to use the Niki SuperCID unlocker but I have to install the " HardSPL 1.15 MFG " first - can you walk mw through this so I dont brick my touch again. do you have messenger?
yeah Windows live messenger, add me [email protected]
sorry to hijack your thread, but I encountered exactly the same thing. The screen is now stuck with 3 colour bands. I tried to flash it with an official rom, but the computer is not connecting with the phone, active sync does not recognise the device, any help!?
this is what I did:
1. download the attached files
2. REMOVE SIM and SD CARDS !!
3. connect usb cable
4. copy sspl-1.16-nike.exe to your device and run it (usb cable must be connected!)
5. after a few seconds "USB" appears on the display
6. unplug and replug the usb cable
8. running ROMUpdateUtility.exe from flash-uspl-niki
Sorry for the non prompt reply
I have been at work alot lately,
sorry for a non prompt reply.
Active sync wont connect to your phone, as its in bootloader mode.
At the tri-colour screen, does you computer beep when you connect it, or try to install drivers?
thanks for replying!
no beep from the computer, when connecting the usb to the phone, the phone changes from "serial" to "usb".
I tried reflashing with ROMUpdateUtility.exe from flash-uspl-niki, it will work, but says fail and will go into recovery mode. It will then complete the "recovery" action and go back to flashing new rom which won't work.......
The same ocurred with me!! Help me!
In the middle of an unlocking process, somehow(in the flashing radio process,i got 100%, and then a message saying: an writing error ocurred). So my htc dual got with the image NIKI200 (and four colour - red,green,blue and white..). Now i tried hard reset and after i presse send to initialize, the phone goes to that bloody image....i cant do nothing....what should i do? help me please....regards
luismatos123 said:
In the middle of an unlocking process, somehow(in the flashing radio process,i got 100%, and then a message saying: an writing error ocurred). So my htc dual got with the image NIKI200 (and four colour - red,green,blue and white..). Now i tried hard reset and after i presse send to initialize, the phone goes to that bloody image....i cant do nothing....what should i do? help me please....regards
Click to expand...
Click to collapse
You need to flash an original ROM from your service provider (phone company).
Hi! I tryed te fash my niki 200 with original rom! The flash is stopes to 42% and now i have boot mode with this message "Upgrade ROM code error! Please try again". I can not conect again to usb because i received message :"usb device not recognized". Mtty can not conect because i received the same message! There is another metod de make this device?
Have you flashed HardSPL?
Put your device into bootloader (hold b oth Camera and Power button while performing a Softreset via Stylus) and now you can theoretically flash your Provider ROM!
After that your device will work again!
I have not flashed hardspl! If i put the Niki in boot mode, show only "serial" on the screen with usb cable pluged and PC says "usb device not recocnized"!
Flashing in bootloader mode doesn't requires an ActiveSync connection so ignore it and start the ROM Upgrade! It's working, believe me! I've flashed my Niki with this method hundred of times!
I tryed to flash my niki in bootmood, but not working "error 260:conection"! My computer not recocnized my device (with or without activesync)!!!In bootmode on screen show "serial" and when i pluged the cable nothing happend (must see on screen:USB)! This is my problem!!! The computer does not alocate to my device a com port(USB). The same problem with MTTY (no USB poet detected). You understand me?
Maybe your USB drivers screwed up.
Trie with an other PC, this helped me one time.
I tryed on other computer with Xp and other with Vista! The same problem! Not recocnized!!!!!!!!!!!!!!!!!
bugytech said:
I tryed on other computer with Xp and other with Vista! The same problem! Not recocnized!!!!!!!!!!!!!!!!!
Click to expand...
Click to collapse
I've got the same issue. Did you resolve this? I would like to find a solution
Hey guys, as the title suggests....im having trouble
Trying to update my ROM.
Active sync works fine, up to the point I have to run the RUU and .nbh files, it just drops out and then i get the error 266 coming up.....asking me to check the cable etc.
Tried different USB ports and leads with no joy.
Strange one this, as I have updated my ROM before (around a year ago) with no trouble.
Help very much appreciated.
marlon32, ActiveSync has nothing to do with flashing process,
Enter bootloader mode (switch off, press & hold Volume down, switch on), than connect to the USB cable.
The word Serial on tricolor screen will be changed for USB.
Now start RomUpdateUtility....
AndrewSh said:
marlon32, ActiveSync has nothing to do with flashing process,
Enter bootloader mode (switch off, press & hold Volume down, switch on), than connect to the USB cable.
The word Serial on tricolor screen will be changed for USB.
Now start RomUpdateUtility....
Click to expand...
Click to collapse
I have also tried this method, but the nothing happens.
When in bootloader mode and the USB cable connected, it is not able to recognise what Image is already on my phone. Even if i click next it fails again with the error 266 msg.
I thought I understood that active sync had to be established first?
Im following these instructions:
FIRST TIME FLASH
1. Remove SD (and remove Application Data and Program Files folders from it using SD card reader)
2. Remove HSPL with HSPL2_RUN.exe (flash SPL 1.66.0000 with HSPL2_RUN.exe)
3. PowerOff the phone
4. Boot to bootloader (VolDown+PowerOn) and when it shows "USB" flash stock ROM by running matching RUU_Leo_S_HTC_XXX_3.14.XXX_Radio_15.42.50.11U_2.15 .50.14_LEO_S_Ship.exe (get yours HERE or for Orange UK/FR HERE)
5. Hard Reset (when phone starts booting after step 4, remove the battery, insert it back press VolUp+VolDown and still holding both press PowerOn and follow the instructions)
6. Boot to homescreen.
7. Run SSPL_RUU.exe with Artemis v4X RUU_Signed_XXXX.nbh in the same folder - YOU HAVE TO BE ON HOME SCREEN, NOT BOOTLOADER (this took me 3 tries until succeded - yes - nerve wrecking, but works). If it doesn't work (hangs on black screen for more than 2min or stays at 0%) remove the battery and try again. If still doesn't work - try solutions in NOTE below.
8. Hard reset (instructions in step 5)
9. when on homescreen - softreset.
10. Insert SD
marlon32 said:
I have also tried this method, but the nothing happens.
When in bootloader mode and the USB cable connected, it is not able to recognise what Image is already on my phone. Even if i click next it fails again with the error 266 msg.
I thought I understood that active sync had to be established first
Click to expand...
Click to collapse
You're going about things in a strange manner, using hspl.exe to set a stock spl and then using sspl to flash the rom? Pretty non standard, what are you aiming for? My guess is you are using outdated instructions from before Hspl4 was released to handle spl/hspl 3.03 (just a guess, of course)
Stabdard flashing a 3.14 rom would go as follows,
Phone into bootloader(forget actuvesync)
Run Hspl4.exe, choose 3.03.hspl
Back into bootloader,
Run the Artemis flash using custom ruu .
Done.
It won't show the current installed image because that is a simple registry entry and is only accessible when winmo is running, but when winmo is running the USB times out when the ruu reboots into bootloader,sim that's why we manually enter bootloader.
(I haven't checked in the Artemis thread as to if there's a reason why his rom wouldn't follow standard proceedures, but I did use exactly your process prior to Hspl4 release)
Thanks for the reply.
What the issue seemed to be (after reading other threads) is that mu laptop is USB 3 and no HTC programme does not like it!
When i used an older laptop everything was fine flashing HSPL 3.03.
Out of interest is it true that USB 3 does not programme correctly?
marlon32 said:
Thanks for the reply.
What the issue seemed to be (after reading other threads) is that mu laptop is USB 3 and no HTC programme does not like it!
When i used an older laptop everything was fine flashing HSPL 3.03.
Out of interest is it true that USB 3 does not programme correctly?
Click to expand...
Click to collapse
Thanks M8 Had the same problem and moved my usb cable to another port worked 100%